Fisher 99449 Parts Manual
Replacement Parts for Pre-Rinse Units
2924-6000
GOOSENECK
SPRING
fisher manufacturing company
73550
SEAT WASHER
RH STEM ADAPTER
LH STEM ADAPTER
73570
OR
73569
T
O
H
H
O
T
CONTROL VALVE
1000-7502
SCREW
5400-CV
5000-2100
3/4” ELBOW
L
D
O
C
C
O
D
L
2000-7500
SCREW
2000-8000
RED BUTTON
AND
2000-8001
BLUE BUTTON
2000-2301
LEVER HANDLE
2000-3002
BIBB CAP
73657
DUCK GASKET
73741
WASHER
2000-3406
LH CHECK STEM
OR
2000-3407
RH CHECK STEM
2000-6000
SPRING
73453
RETAINER
ASSEMBLY
73521
LUBE
2992
PST
2902-12
WALL BRACKET
5000-0012
RH CHECK STEM
REPAIR KIT
OR
5000-0013
LH CHECK STEM
REPAIR KIT
2927-4300
16” RISER
5000-0020
14” SWING SPOUT
5000-0001
10” SWING SPOUT
5000-0002
7” SWING SPOUT
HOSE HOOK
72813
CHEM TEE
ULTRA SPRAY VALVE
36” SS HOSE
2925-6300
INSULATED
2949
2914
2913
HANDLE
PRTS-CTA-8BSEELL
Product Installation Guide
Since 1936, Fisher Manufacturing Company has
manufactured heavy-duty, high quality plumbing
products and hardware specialties for the food service
industry. For three generations, the Fisher family has
adhered to a strict dedication of and overall value.
When you install Fisher products… you install the best.
Our hardware is manufactured with the standardization
of internal mechanisms. All chrome plating is triple
plated copper, nickel and chrome for durability. Every
piece of equipment we make is rigorously tested in
both our modern in-house testing center and in actual
field situations under extreme conditions. Every detail
is thoroughly checked. Before we make our products
available to you, they pass each and every test. You get
proven performance. Guaranteed.
Limited One Year Warranty
Fisher Manufacturing Company warrants its products
and parts thereof (except as noted below) against
defects in materials or workmanship for a period of
one year after the date of original purchase. During
this period Fisher Manufacturing Company will
replace a defective product or part without charge to
you, provided that the entire product is delivered to
Fisher Manufacturing Company. All transportation and
insurance charges for shipping the product to and from
Fisher Manufacturing Company must be borne by you.
Charges for transportation and insurance may, at the
option of Fisher Manufacturing Company, be refunded
depending upon our investigation of the warranty claim.
This warranty does not cover external finish (except at
date of original purchase) or labor costs not specifically
authorized by Fisher Manufacturing Company.
A full and complete copy of our One Year limited
warranty is available upon request.
WARNING:
Proposition 65 requires that we provide you with the
following notice: “This product Contains A Chemical
Known To The State Of California To Cause Birth
Defects Or Other Reproductive Harm.”
#49530 - 3/4 PRERINSE SPGCT 8BSELH 10SS
#99449 - 3/4 PRERINSE SPGCT 8BSELH 14SS
PART NO. 74679
20788
ADD-ON-CONTROL
VALV E
MANFACTURING COMPANY
PO BOX 60, TULARE, CA 93275
(800)421-6162, FAX: (800)832-8238
www.fisher-mfg.com
KEEP THIS MANUAL FOR FUTURE REFERENCE
ANSI/A112.18.1M, ANSI/NSF 61.9
fisher manufacturing company - toll free: 800-421-6162 fax: 800-832-8238
REV. A
www.fi sher-mfg.com
Installation Instructions for Pre-Rinse Units
Installation Instructions Continued
BE SURE TO CHECK WITH YOUR LOCAL DEPARTMENT HAVING JURISDICTION
REGARDING BACKFLOW PREVENTION
Installation Notes:
• Be sure to shut off water supply before beginning.
• Use pipe thread sealant such as PST on all threaded joints.
• Check the packaging for missing items BEFORE beginning installation. If items are missing, contact
your supplier.
Tools Required for Installation
• Medium Sized Crescent Wrenches
• Pipe Thread Sealant
• Phillips Screwdriver
• 7/16” Drill Bit
• 1/8” Allen Wrench
Installation Instructions
1. Insert the control valve through the backsplash
sink place the washer and nut on the nipple and
tighten, then put the elbow and tighten. Connect
water supply to the elbows
2. Place the 2 serrated washers into the control valve
stacked on top of each other. Apply lube sealant to
the o-rings on the add on body. Insert the add-on
body into the control valve outlet. Position the addon body and tighten the nut.
3. Mount the pipe to hose adapter to the enclosed
riser using thread sealant. Mount the other end of
the riser to the female outlet of the add-on body
4. Proceed by installing the wall bracket with following steps below.
a. Locate and drill a Ø7/16” hole in the wall directly
behind and about 3/4 the way up the riser pipe.
b. Loosely attach the front and back of the pipe
clamp onto the riser pipe.
c. Hold the wall bracket fl ange against the wall,
centered with the hole. Use the wall screws and
a screw driver to mount the fl ange to the wall.
d. Slide part, but not all, of the wall bracket rod
non-threaded end fi rst through the center hole
of the fl ange and into the wall.
e. Align the rod with the pipe clamp and thread the
rod into the pipe clamp. Be sure the rod is level
by adjusting the pipe clamp position.
f. Once level, fi x the rod in place by tightening
both the set screw located in the fl ange and the
pipe clamp screws.
5. Slip the hose hook over the pipe to hose adapter.
Apply thread sealant to the SS hose and attach the
SS hose to the pipe to hose adapter and tighten
SS hose.
6. Install gooseneck spring by slipping SS hose
through the spring. Spring will fi t over adapter
which holds it in an upright position. Note: Be sure
spring is installed as shown.
7. Place the handle gaskets inside the outlets of the
insulated handle. Attach the insulated handle to
the SS hose and to the spray valve.
8. Apply lube to the o-rings on swing spout, insert the
swing spout in to the add-on faucet outlet and
tighten the spout nut.
9. Turn on water supply and check for leaks.
PST
Step 1
Step 2
Apply Lube
Step 3
Thread Sealant
Goes Here
Washer
Elbow
Nut
Serrated Washer
Step 4
Excess Rod Length
Trim to Fit (optional)
Wall
Wall Screw
Set Screw
Pipe
Clamp
Riser Pipe
Step 6 Step 7
Handle Gasket
Handle Gasket
Step 8
Swing Spout
Apply O-Ring
Lube Here
Step 5
Thread Sealant
Goes Here
Step 9
Loading...