Epson PixiePlus Control System fors Installation Supplement

PixiePlusTM ELPSP10 Supplement

for the Epson® Projector Controller

Contents

1. Installation of the Epson Projector Controller with the Epson AP-60 Configuration 1 – Projector Volume Control Configuration 2 – AP-60 IR Volume Control

2. Using the Programming Wand (PXE-PGM-TOOL) to Reprogram the PixiePlus

3. Using the Programming Wand to Set Schedule Events

4. Restoring the PixiePlus to its Default Preconfiguration

1. Installation of the Epson Projector Controller with the Epson AP-60

The PixiePlus may be easily set up to work with the Epson AP-60 Audio System in two basic configurations.

Configuration 1 – Projector Volume Control

In this configuration, route the audio for the various display devices in your room through your Epson projector. The PixiePlus will control the audio switching and volume level on the projector with its preconfigured RS-232 codes. Connect the audio output from the projector to the audio input on the AP-60.

A. Connect the audio outputs from your display devices to your projector as shown in the projector documentation.

B. Connect the 3.5mm jack labeled Audio Out on your projector to the AP-60 jack labeled Line 1 LCP.

Once this cable is connected the projector speakers will be inactive. C. If you wish to control the power On/Off of the AP-60 connect the IR emitter output

from PixiePlus Ceiling Plate to the IR receiver of AP-60 to enable power control of AP-60 when the PixiePlus Audio button is pressed. The IR codes for AP-60 are preconfigured in the PixiePlus.

Configuration 2 – AP-60 IR Volume Control

In this configuration the PixiePlus will control the volume level of the AP-60 directly with IR codes. If you have multiple audio sources, you should consider how to handle audio switching before implementing this configuration. Connect audio devices to the AP-60 as shown in the AP-60 Installat i on Guide .

Note: This configuration requires reprogramming the PixiePlus volume buttons with IR volume commands for the AP-60. For complete instructions on reprogramming PixiePlus buttons, see the PixiePlus Installation Guide, pages 8 and following.

A. Wire the IR output from the PixiePlus Ceiling Plate to the IR receiver window on the AP-60 (see the

PixiePlus Installation Guide,

pages 6-7). B. To reprogram the

PixiePlus volume buttons with IR volume commands, insert a paper clip into the small opening on the lower-right of the PixiePlus labeled Insert paper clip here to enter learning mode. The learning mode indicator LED on the PixiePlus will begin flashing red. If it does not, be sure the PixiePlus is powered.

C. Press the Volume Down button on the PixiePlus a single time. It will beep once, indicating that it is armed for learning an IR code. Hold the AP-60 remote control perpendicular to the PixiePlus about 2-3 inches from the IR receiver labeled aim remote here to be learned in the upper-right of the frame. Press the Volume - button on the remote control for about a second, then release it. The PixiePlus will beep three times to indicate that the code has been learned correctly. If you do not hear the confirmation beeps, repeat these steps.

D. Press the Volume + button on the PixiePlus to arm it for learning. Repeat the process described in step 3, except pressing the Volume + button on the AP-60 remote control.

E. When the volume buttons are successfully reprogrammed, remove the paper clip to return the PixiePlus to normal operation.

Note: Reprogramming any button erases the code that is already in place. F. To restore the PixiePlus to its factory default preconfiguration. Simply place the

PixiePlus in learning mode by inserting the paper clip, then press and hold any two buttons on the PixiePlus for 5 to 10 seconds. When the unit beeps three times, it will be restored to its factory default configuration.

+ 3 hidden pages