Epson DW847 User Manual

INSTRUCTIVO DE OPERACIÓN, CENTROS DE SERVICIO Y PÓLIZA

DE GARANTÍA. ADVERTENCIA: LÉASE ESTE INSTRUCTIVO ANTES

DE USAR EL PRODUCTO.

Si tiene dudas o comentarios, contáctenos.

If you have questions or comments, contact us.

Pour toute question ou tout commentaire, nous contacter.

1-800-4-DEWALT • www.dewalt.com

INSTRUCTION MANUAL

GUIDE D'UTILISATION

MANUAL DE INSTRUCCIONES

DEWALT Industrial Tool Co., 701 East Joppa Road, Baltimore, MD 21286

The following are trademarks for one or more DEWALT power tools: the yellow and black colorscheme; the “D” shaped air intake grill; the array of pyramids on the handgrip; the kit box configuration; and the array of lozenge-shaped humps on the surface of the tool.

Definitions: Safety Guidelines

The definitions below describe the level of severity for each signal word. Please read the manual and pay attention to these symbols.

DANGER: Indicates an imminently hazardous situation which, if not

avoided, will result in death or serious injury.

WARNING: Indicates a potentially hazardous situation which, if not

avoided, could result in death or serious injury.

CAUTION: Indicates a potentially hazardous situation which, if not

avoided, may result in minor or moderate injury. CAUTION: Used without the safety alert symbol indicates a potentially

hazardous situation which, if not avoided, may result in property damage.

IF YOU HAVE ANY QUESTIONS OR COMMENTS ABOUT THIS OR ANY DEWALT TOOL, CALL US TOLL FREE AT: 1-800-4-D

General Safety Rules – For All Tools

WARNING! Read and understand all instructions. Failure to follow all instructions listed below may result in electric shock, fire and/or serious personal injury.

SAVE THESE INSTRUCTIONS

WORK AREA

• Keep your work area clean and well lit. Cluttered benches and dark areas invite

accidents.

• Do not operate power tools in explosive atmospheres, such as in the presence of flammable liquids, gases, or dust. Power tools create sparks which may ignite the dust or fumes.

• Keep bystanders, children, and visitors away while operating a power tool. Distractions can cause you to lose control.

ELECTRICAL SAFETY

• Grounded tools must be plugged into an outlet properly installed and grounded in accordance with all codes and ordinances. Never remove the grounding prong or modify the plug in any way. Do not use any adaptor plugs. Check with a qualified electrician if you are in doubt as to whether the outlet is properly grounded. If the tools

should electrically malfunction or break down, grounding provides a low resistance path to carry electricity away from the user. Applicable only to Class I (grounded) tools.

• Double insulated tools are equipped with a polarized plug (one blade is wider than the

other.) This plug will fit in a polarized outlet only one way. If the plug does not fit fully in the outlet, reverse the plug. If it still does not fit, contact a qualified electrician to install a polarized outlet. Do not change the plug in any way. Double insulation

eliminates the need for the three wire grounded power cord and grounded power supply system. Applicable only to Class II (double insulated) tools.

• Avoid body contact with grounded surfaces such as pipes, radiators, ranges and refrigerators. There is an increased risk of electric shock if your body is grounded.

• Don’t expose power tools to rain or wet conditions. Water entering a power tool will increase the risk of electric shock.

• Do not abuse the cord. Never use the cord to carry the tools or pull the plug from an

outlet. Keep cord away from heat, oil, sharp edges or moving parts. Replace damaged cords immediately. Damaged cords increase the risk of electric shock.

• When operating a power tool outside, use an outdoor extension cord marked “W-A” or “W.” These cords are rated for outdoor use and reduce the risk of electric shock. When

using an extension cord, be sure to use one heavy enough to carry the current your product will draw. An undersized cord will cause a drop in line voltage resulting in loss of power and overheating. The following table shows the correct size to use depending on cord length and nameplate ampere rating. If in doubt, use the next heavier gauge. The smaller the gauge number, the heavier the cord.

EWALT (1-800-433-9258)

DW845, DW847, DW849

Polishers

Polisseuses

EWALT

Pulidoras

Volts Total Length of Cord in Feet

120V 0-25 26-50 51-100 101-150 240V 0-50 51-100 101-200 201-300

Ampere Rating

More Not more AWG Than Than 0 - 6 18 16 16 14 6 - 10 18 16 14 12 10 - 12 16 16 14 12 12 - 16 14 12 Not Recommended

PERSONAL SAFETY

• Stay alert, watch what you are doing and use common sense when operating a power tool. Do not use tool while tired or under the influence of drugs, alcohol, or medication.

A moment of inattention while operating power tools may result in serious personal injury.

• Dress properly. Do not wear loose clothing or jewelry. Contain long hair. Keep your hair, clothing, and gloves away from moving parts. Loose clothing, jewelry, or long hair can be caught in moving parts. Air vents often cover moving parts and should also be avoided.

• Avoid accidental starting. Be sure switch is off before plugging in. Carrying tools with your finger on the switch or plugging in tools that have the switch on invites accidents.

• Remove adjusting keys or wrenches before turning the tool on. A wrench or a key that is left attached to a rotating part of the tool may result in personal injury.

• Do not overreach. Keep proper footing and balance at all times. Proper footing and balance enables better control of the tool in unexpected situations.

• Use safety equipment. Always wear eye protection. Dust mask, non-skid safety shoes, hard hat, or hearing protection must be used for appropriate conditions.

TOOL USE AND CARE

• Use clamps or other practical way to secure and support the workpiece to a stable platform. Holding the work by hand or against your body is unstable and may lead to loss of

control.

• Do not force tool. Use the correct tool for your application. The correct tool will do the job better and safer at the rate for which it is designed.

• Do not use tool if switch does not turn it on or off. Any tool that cannot be controlled with the switch is dangerous and must be repaired.

• Disconnect the plug from the power source before making any adjustments, changing accessories, or storing the tool. Such preventative safety measures reduce the risk of starting the tool accidentally.

• Store idle tools out of reach of children and other untrained persons. Tools are dangerous in the hands of untrained users.

• Maintain tools with care. Keep cutting tools sharp and clean. Properly maintained tools, with sharp cutting edges are less likely to bind and are easier to control.

• Check for misalignment or binding of moving parts, breakage of parts, and any other

condition that may affect the tool’s operation. If damaged, have the tool serviced before using. Many accidents are caused by poorly maintained tools.

• Use only accessories that are recommended by the manufacturer for your model. Accessories that may be suitable for one tool, may become hazardous when used on another tool.

SERVICE

• Tool service must be performed only by qualified repair personnel. Service or maintenance performed by unqualified personnel could result in a risk of injury.

• When servicing a tool, use only identical replacement parts. Follow instructions in the Maintenance section of this manual. Use of unauthorized parts or failure to follow maintenance instructions may create a risk of electric shock or injury.

Minimum Gauge for Cord Sets

Additional Specific Safety Instructions for Polishers

• Always use proper guard with grinding wheel. A guard protects operator from broken wheel fragments and wheel contact.

• Hold tool by insulated gripping surfaces when performing an operation where the cutting tool may contact hidden wiring or its own cord. Contact with a “live” wire will

make exposed metal parts of the tool “live” and shock the operator.

• Always use eye protection. All users and bystanders must wear eye protection that conforms to ANSI Z87.1.

• Clean out your tool often, especially after heavy use. Dust and grit containing metal particles often accumulate on interior surfaces and could create an electric shock hazard.

• Do not operate this tool for long periods of time. Vibration caused by the operating action of this tool may cause permanent injury to fingers, hands, and arms. Use gloves to provide extra cushion, take frequent rest periods, and limit daily time of use.

• Do not allow any loose portion of the polishing bonnet or its attachment strings to spin

freely. Tuck away or trim any loose attachment strings. Loose and spinning attachment strings can entangle your fingers or snag on the workpiece.

Causes and Operator Prevention of Kickback

• Kickback is a sudden reaction to a pinched, bound or misaligned wheel, wire brush or flap disc causing an uncontrolled cut-off tool to lift up and out of the workpiece toward the operator.

• When the wheel is pinched or bound tightly by the workpiece, the wheel stalls and the motor reaction drives the unit rapidly back toward or away from the operator.

• Kickback is the result of tool misuse and/or incorrect operating procedures or conditions and can be avoided by taking proper precautions as given below:

• Maintain a firm grip with both hands on the unit and position your body and arm to allow you to resist kickback forces. Kickback forces can be controlled by the operator, if proper precautions are taken.

• When wheel is binding, or when interrupting a cut for any reason, release the trigger

and hold the unit motionless in the material until the wheel comes to a complete stop. Never attempt to remove the unit from the work or pull the unit backward while the wheel is in motion or kickback may occur. Investigate and take corrective actions

to eliminate the cause of wheel binding.

• When restarting a cut-off accessory in the workpiece, check that the wheel is not engaged into the material. If wheel is binding, it may walk up or kickback from the workpiece as the tool is restarted.

• Support large panels to minimize the risk of wheel pinching and kickback. Large panels tend to sag under their own weight. Support must be placed under the panel on both sides, near the line of cut and near the edge of the panel.

WARNING: ALWAYS use safety glasses. Everyday eyeglasses are NOT safety glasses.

Also use face or dust mask if cutting operation is dusty. ALWAYS WEAR CERTIFIED SAFETY EQUIPMENT:

• ANSI Z87.1 eye protection (CAN/CSA Z94.3),

• ANSI S12.6 (S3.19) hearing protection,

• NIOSH/OSHA/MSHA respiratory protection.

WARNING: Always wear proper personal hearing protection that conforms to ANSI

S12.6 (S3.19) during use. Under some conditions and duration of use, noise from this product

may contribute to hearing loss.

WARNING: Some dust created by power sanding, sawing, grinding, drilling, and other

construction activities contains chemicals known to cause cancer, birth defects, or other reproductive harm. Some examples of these chemicals are:

• lead from lead-based paints,

• crystalline silica from bricks and cement and other masonry products, and

• arsenic and chromium from chemically-treated lumber (CCA).

Your risk from these exposures varies, depending on how often you do this type of work. To reduce your exposure to these chemicals: work in a well ventilated area, and work with approved safety equipment, such as those dust masks that are specially designed to filter out microscopic particles.

• Avoid prolonged contact with dust from power sanding, sawing, grinding, drilling, and

other construction activities. Wear protective clothing and wash exposed areas with soap and water. Allowing dust to get into your mouth, eyes, or lay on the skin may promote

absorption of harmful chemicals.

WARNING: Use of this tool can generate and/or disburse dust, which may cause serious and

permanent respiratory or other injury. Always use NIOSH/OSHA approved respiratory protection appropriate for the dust exposure. Direct particles away from face and body.

CAUTION: Use extra care when working into a corner because a sudden, sharp movement

of the grinder may be experienced when the wheel or other accessory contacts a secondary surface or a surface edge.

• The label on your tool may include the following symbols. The symbols and their definitions are as follows:

V ......................volts A ................amperes

Hz ....................hertz W ...............watts

min ..................minutes

...............direct current

.............alternating current

o ..............no load speed

....................Class I Construction ...............earthing terminal

........................(grounded)

..............safety alert symbol

....................Class II Construction …/min ........revolutions or reciprocation

........................(double insulated) ...................per minute

BPM ................beats per minute

SAVE THESE INSTRUCTIONS

Motor

Your

DEWALT

with the nameplate marking. Voltage decrease of more than 10% will cause loss of power and overheating.

COMPONENTS (Fig. 1, 2, 3)

WARNING: Never modify the power tool or any part of it. Damage or personal injury could

result.

A. Speed Control Wheel (DW849 only) B. Cushion Tool Reset (DW847, DW849 only) C. Trigger Switch D. Brush Inspection Cap E. Spindle Lock Button F. Auxiliary Handle G. Trigger Locking Button

INTENDED USE

The DW845, DW847 and DW849 heavy-duty polishers are designed for professional use at various work sites (i.e., construction sites). Do not use under humid conditions or in presence of flammable liquids or gases.

The DW845, DW847 and DW849 heavy-duty polishers are professional power tools. Do not let children come into contact with the tool. Supervision is required when inexperienced operators use this tool.

Auxiliary Handle (Fig. 1)

An auxiliary handle (F) is furnished with your tool and can be installed on either side of the front housing. This handle should be used at all times to maintain complete control of the tool.

Variable Speed Switch

These tools are equipped with a variable speed switch that permits speed control from (0 to 1750 RPM - DW847) (0 to 1000/0 to 3000 RPM - DW849) (0 to 2300 RPM - DW845). To turn the tool on, squeeze the trigger switch (C) shown in Figure 2 until the tool starts to run. The farther you depress the trigger, the faster it will operate. Releasing the trigger turns the tool off.

Use lower speeds for applying liquid waxes and polishes and higher speeds for removing dried liquid. Use the highest speed (fully depress trigger) for buffing the car to a final lustre.

The tool can be locked on for continuous use by squeezing the trigger switch fully and depressing the lock button (G) shown in Figure 2. Hold the lock button in as you gently release the trigger switch. The tool will continue to run. To turn the tool off from a locked on position, squeeze and release the trigger switch once. Do not unplug the tool with the switch in the locked on condition. Make sure the tool is not locked on when plugging in. A locked on tool will start immediately when plugged in.

NOTE: The trigger can only be locked on with the tool running at the maximum RPM.

Speed Control Wheel (DW849 only)

The maximum speed of your tool can be changed by rotating the speed control wheel (A) to the desired setting. The wheel incorporates detents to prevent inadvertent wheel movement and to facilitate speed selection. For added versatility, the switch may be locked in its full on position and tool speed changed by means of the speed control wheel (A) alone (see Figure 3).

The electronic speed control not only lets you select the speed to suit the job, but also helps to maintain that speed as you load the tool by pressing down. It’s this feature, coupled with the variable speed switch, that make this tool such a value.

The speed control wheel (A) can be set for any speed between 1000 and 3000 RPM and the variable speed switch will then control tool speed from zero to the wheel setting. For example: A control wheel setting of 2200 RPM will allow the variable speed switch to operate the tool between zero and 2200 RPM, depending on how far the trigger is depressed. A wheel setting of 1000 RPM would allow the switch to operate the tool from zero RPM to 1000 RPM.

The electronic speed control feature comes into play whenever the trigger switch is fully depressed and the tool is running at the selected speed determined by the setting of the control wheel. As you load the tool by pushing it down on the work surface, (with the trigger fully depressed) the electronic circuit inside the tool will compensate for the loading and maintain the selected speed. If the speed selected by the control wheel is 2200 RPM, as in the example above, the tool will maintain 2200 RPM, as it is loaded.

It is important to remember two things about electronic speed control:

1. The electronic speed control operates only when the trigger switch (C) is fully depressed.

2. The effect of electronic speed control is much easier to observe at lower speed settings (2600 RPM and below), than at high speeds. As the tool approaches 3000 RPM, the effect is considerably less dramatic.

Keep in mind that, with a conventional polisher running at a typical no load speed of 2400 RPM, the tool slows down to about 2000 RPM under a polishing load. Your DW849 will continue to run at 2400 RPM (or any speed you select with the control wheel) as a load is applied. Since it doesn’t slow down, the speed may be greater than you’re used to so some extra caution should be observed until you get the “feel” of your polisher. If you feel the speed is too great, you can, of course slow the tool down with either the trigger switch or the control wheel.

Spindle Lock Button (Fig. 1)

WARNING: To reduce the risk of serious personal injury, turn tool off and disconnect tool from power source before making any adjustments or removing/installing attachments or accessories. Before reconnecting the tool, depress and release the trigger switch to ensure that the tool is off.

In order to prevent the spindle of the tool from rotating while installing or removing accesso-

ries, a spindle lock button (E) has been provided in the gear head of the machine. To lock the spindle, depress and hold the lock button. NEVER DEPRESS THE SPINDLE LOCK BUTTON WITH THE TOOL RUNNING OR COASTING.

OPERATION

Attaching and Removing Polishing Pads (Fig. 4, 5)

WARNING: To reduce the risk of serious personal injury, do not allow any loose portion of the polishing bonnet or its attachment strings to spin freely. Tuck away or trim any loose attachment strings. Loose and spinning attachment strings can entangle your fingers or snag on the workpiece.

TO ATTACH PAD

1. To attach pad (H), push the hub of the clamp washer through the hole in the center of the

polishing pad as far as it will go.

2. Engage the hexagonal hole in the backing pad. Holding the three pieces firmly together,

place the assembly on the tool spindle.

3. Hold the spindle lock button while turning the pads clockwise to thread them completely on

the spindle.

TO REMOVE PADS

Turn them by hand in the opposite direction from normal rotation to allow lock button to engage spindle, then unscrew pads in normal direction for right hand thread.

NOTE: If you are using a polishing bonnet, rather than a pad, put clamp washer on first, pull bonnet completely over backing pad and pull draw strings tight Tie bow knot and push knot and all loose string completely under the inside, cloth edge of the polishing bonnet.

Polishing

These instructions and suggestions are intended to familiarize new operators in overall general operation of power polishing. You will develop your own techniques which will make the job easier and faster as you learn power polishing.

tool is powered by a

DEWALT

tools are factory tested; if this tool does not operate, check power supply.

DEWALT

-built motor. Be sure your power supply agrees

FIG. 6

FIG. 1

FIG. 2

FIG. 4

FIG. 7

INSTALLING

INSTALLATION

NSTALACIÓN

FIG. 5

FIG. 9

FIG. 3

FIG. 8

REMOVING

RETRAIT

QUITAR

• You should use utmost care when power polishing around or over sharp objects and con-

tours of the car body. It is very important to use the correct pressure while polishing various sections of an automobile body. For example, light pressure should be applied when polishing over sharp edges of body panels, or over edges of the rain gutter along the top.

• Since everyone does not use the same type of power polish, we recommend you clean and

polish a test section on a flat area of the car first. From this test section, you can judge the strength or cleaning action of your power polish.

• Remember, all power polish is not the same. Different brands will react differently on various

painted surfaces. Also, you are now using a power polisher with power polish. This is entirely different from any hand application which you may have done before. Wash the car before power polishing it. Washing will remove loose dirt, scum, road salt, etc. which could act as an abrasive and damage paint. Loose dirt, etc. will also clog the polishing pad and you will have to clean it more often.

• Without turning the tool on, grasp the handles of the tool and pick it up. Keep the tool away

from your body and turn the switch on. Make sure you have a firm grip on the handles and operate the tool freely without forced effort or unnecessary pressure. The side handle can be easily changed to either side of the tool for left-handed or right-handed operation.

NOTE: The high speed rubbing action of the polishing bonnet upon the surface of an automobile can build a static charge on the metal portions of this tool. This can result in a sensation of a very short mild electric shock when the metal area of the tool is touched, and will be more noticeable on days when the humidity is low. This is a harmless phenomenon but you are invited to bring the tool to a D no electrical malfunction is present.

EWALT service center where it can be checked to assure that

Sanding (DW849 only)

WARNING:

• Do not sand metal of any kind with your polisher. Sparks may be generated by sanding

screws, nails or other metals which may ignite dust particles.

• Do not wet sand with this polisher. Liquids may enter the motor housing and cause electric

shock.

• Clean out your tool often, especially after heavy use. Dust and grit containing metal particles

often accumulate on interior surfaces and could create a risk of serious injury, electric shock or electrocution. Wear proper ANSI Z87.1 (CAN/CSA Z94.3) eye protection.

TO ATTACH SANDING DISC (FIG. 6–8)

1. Push the hub of the clamp washer (I) through the center of the sanding (M) and phenolic

discs (L), as far as it will go, and also through the backing pad.

2. Engage the clamp washer threads on the tool spindle and thread assembly clockwise, com-

pletely down on the spindle.

3. Hold the spindle from rotating by engaging the spindle lock button.

TO REMOVE ABRASIVE DISC (FIG. 6–8)

Use a cloth or glove to protect your hand. Turn the disc assembly counterclockwise (Figure 8). Hold the spindle from rotating by engaging the spindle lock button.

SANDING (FIG. 9)

When using an abrasive disc, hold the tool so that an angle of 10º to 15º exists between the disc and the work. If only the outer edge of the sanding disc is used, a rough cut will result. If the sanding disc is pressed flat against the work, the sanding action will be irregular and bumpy, and the tool will be difficult to control.

MAINTENANCE

WARNING: To reduce the risk of serious personal injury, turn tool off and disconnect tool from power source before making any adjustments or removing/installing attachments or accessories.

Cleaning

WARNING: Blow dirt and dust out of all air vents with dry air at least once a week. Wear proper ANSI Z87.1 (CAN/CSA Z94.3) eye protection and proper NIOSH/OSHA/MSHA respiratory protection when performing this.

WARNING: Never use solvents or other harsh chemicals for cleaning the non-metallic parts of the tool. These chemicals may weaken the plastic materials used in these parts. Use a cloth dampened only with water and mild soap. Never let any liquid get inside the tool; never immerse any part of the tool into a liquid.

Lubrication

DEWALT tools are properly lubricated at the factory and are ready for use. Tools should be relubricated regularly every sixty days to six months, depending on usage. (Tools used constantly on production or heavy-duty jobs and tools exposed to heat may require more frequent lubrication.) This lubrication should only be attempted by trained power tool repairpersons such as those at D

EWALT service centers or other authorized service locations.

Motor Brushes

Be sure tool is unplugged before inspecting brushes. Carbon brushes should be regularly inspected for wear. To inspect brushes, unscrew the plastic brush inspection caps (located in the sides of the motor housing) and the spring and brush assemblies may be withdrawn from the tool. Keep brushes clean and sliding freely in their guides. Carbon brushes have varying symbols stamped into them, and if the brush is worn down to the line closest to the spring, they must be replaced.

Accessories

WARNING: Since accessories, other than those offered by DEWALT, have not been tested

with this product, use of such accessories with this tool could be hazardous. To reduce the risk of injury, only D

Recommended accessories for use with your tool are available at extra cost from your local dealer or authorized service center. If you need assistance in locating any accessory, please contact D

EWALT (1-800-433-9258) or visit our website www.dewalt.com.

D Use only accessories having a maximum operating speed at least as high as the highest “NO

LOAD RPM” marked on the tool’s nameplate. This precaution applies to any accessory on any tool.

Rubber Backing Pads: 7" Quick Change Super Flexible Rubber Backing Pad (includes Clamp Washer)

Polishing Bonnets and Pads: D and 9" polishers. See your local D

EWALT, recommended accessories should be used with this product.

EWALT Industrial Tool Co., 701 East Joppa Road, Baltimore, MD 21286, call 1-800-4-

EWALT has an array of polishing bonnets and pads for 7"

EWALT service center.

Repairs

To assure product SAFETY and RELIABILITY, repairs, maintenance and adjustments (including brush inspection and replacement) should be performed by a D a D

EWALT authorized service center or other qualified service personnel. Always use identical

replacement parts.

EWALT factory service center,

Three Year Limited Warranty

DEWALT will repair, without charge, any defects due to faulty materials or workmanship for three years from the date of purchase. This warranty does not cover part failure due to normal wear or tool abuse. For further detail of warranty coverage and warranty repair information, visit www.dewalt.com or call 1-800-4-D accessories or damage caused where repairs have been made or attempted by others. This warranty gives you specific legal rights and you may have other rights which vary in certain states or provinces.

In addition to the warranty, D

EWALT will maintain the tool and replace worn parts caused by normal use, for free, any time

D during the first year after purchase.

If you are not completely satisfied with the performance of your D Nailer for any reason, you can return it within 90 days from the date of purchase with a receipt for a full refund – no questions asked.

LATIN AMERICA: This warranty does not apply to products sold in Latin America. For products sold in Latin America, see country specific warranty information contained either in the packaging, call the local company or see website for warranty information.

FREE WARNING LABEL REPLACEMENT: If your warning labels become illegible or are missing, call 1-800-4-D

EWALT for a free replacement.

EWALT (1-800-433-9258). This warranty does not apply to

EWALT tools are covered by our:

1 YEAR FREE SERVICE

90 DAY MONEY BACK GUARANTEE

EWALT Power Tool, Laser, or

Définitions : lignes directrices en

matière de sécurité

Les définitions ci-dessous décrivent le niveau de danger pour chaque mot-indicateur employé. Veuillez lire le mode d’emploi et porter une attention particulière à ces symboles.

DANGER : indique une situation dangereuse imminente qui, si elle n’est pas

évitée, causera la mort ou des blessures graves.

AVERTISSEMENT : indique une situation potentiellement dangereuse qui, si elle

n’est pas évitée, pourrait se solder par un décès ou des blessures graves.

MISE EN GARDE : indique une situation potentiellement dangereuse

qui, si elle n’est pas évitée pourrait se solder par des blessures mineures ou

modérées. MISE EN GARDE : utilisé sans le symbole d’alerte à la sécurité, indique une situation

potentiellement dangereuse qui, si elle n’est pas évitée pourrait se solder par des dommages à la propriété.

POUR TOUT RENSEIGNEMENT SUPPLÉMENTAIRE SUR L’OUTIL OU TOUT AUTRE OUTIL D

EWALT, COMPOSER SANS FRAIS LE 1-(800)-4-DEWALT (1-(800)-433-9258).

Importantes mesures de sécurité

AVERTISSEMENT! Lire et assimiler toutes les directives. Le non-respect des directives indiquées ci-dessous peut entraîner des risques de choc électrique, d’incendie ou de blessures corporelles graves.

CONSERVER CES DIRECTIVES

ESPACE DE TRAVAIL

• Tenir l’espace de travail propre et bien éclairé. Les établis encombrés et les endroits

sombres sont souvent propices aux accidents.

• Ne pas faire fonctionner d’outils électriques dans un milieu déflagrant, par exemple en présence de liquides, de gaz ou de poussières inflammables. Les outils électriques produisent des étincelles qui peuvent enflammer la poussière ou les vapeurs.

• Éloigner les curieux, les enfants et les visiteurs lors de l’utilisation d’un outil électrique. Une distraction pourrait vous en faire perdre la maîtrise.

SÉCURITÉ EN MATIÈRE D’ÉLECTRICITÉ

• Les outils mis à la terre doivent être branchés dans une prise correctement installée et mise à la terre tel que l’indiquent les codes et règlements en vigueur. Ne jamais retirer la broche de mise à la terre ou modifier la prise en aucune façon. Ne pas utiliser de fiche d’adaptation. Consulter un électricien qualifié s’il y a un doute en ce qui concerne la mise à la terre de la prise. En cas de défaillance électrique ou de bris de

l’outil, la mise à la terre procure un chemin de faible résistance au courant afin de réduire les risques de choc électrique. Ne s’applique qu’aux outils de classe I (mis à la terre).

• Les outils à double isolation sont dotés d’une fiche polarisée (une lame de contact est

plus large que l’autre). Elle ne se branchera que d’une seule façon dans une prise de courant polarisée. Si la fiche ne s’insère pas totalement dans la prise de courant, l’inverser. Si elle ne s’insère toujours pas dans la prise, demander à un électricien qualifié d’installer une prise polarisée. Ne pas remplacer la fiche. La

double isolation à trois fils avec mise à la terre et un bloc d’alimentation avec mise à la terre. Ne s’applique

qu’aux outils de classe II (à double isolation).

• Éviter tout contact physique avec des surfaces mises à la terre comme des tuyaux, des radiateurs, des cuisinières et des réfrigérateurs. Le risque de choc électrique est

plus élevé lorsque le corps est mis à la terre.

• Ne pas exposer les outils électriques à la pluie ou à un environnement humide. La pénétration de l’eau dans un outil électrique augmente le risque de choc électrique.

• Ne pas utiliser le cordon de façon abusive. Ne pas utiliser le cordon pour transporter

l’outil ni tirer dessus pour le débrancher de la prise de courant. Tenir le cordon éloigné de la chaleur, de l’huile, des bords tranchants et des pièces mobiles. Remplacer immédiatement tout cordon endommagé. Un cordon endommagé augmente le risque de

choc électrique.

• Lorsqu’un outil électrique est utilisé à l’extérieur, utiliser une rallonge pour l’extérieur portant la mention « W-A » ou « W ». Ces rallonges sont classées pour un usage extérieur, ce qui réduit le risque de choc électrique. Lorsqu’une rallonge est utilisée, s’assurer d’utiliser un calibre suffisamment élevé pour assurer le transport du courant nécessaire au fonctionnement de l’appareil. Une rallonge de calibre inférieur causera une chute de tension de ligne et donc une perte de puissance et une surchauffe. Le tableau suivant indique le calibre approprié à utiliser selon la longueur de la rallonge et l’intensité nominale de la plaque signalétique. En cas de doute, utiliser le calibre supérieur suivant. Plus le numéro de calibre est petit, plus le cordon est lourd.

Volts Longueur totale de la rallonge en pieds

120 V 0-25 26-50 51-100 101-150 240 V 0-50 51-100 101-200 201-300

Intensité nominale

Plus Pas plus AWG de de 0 - 6 18 16 16 14 6 - 10 18 16 14 12 10 - 12 16 16 14 12 12 - 16 14 12 Non recommandé

SÉCURITÉ PERSONNELLE

• Rester vigilant, faire attention au travail en cours et faire preuve de jugement dans l’utilisation de tout outil électrique. Ne pas utiliser d’outil en cas de fatigue ou sous l’emprise de drogues, d’alcool ou de médicaments. Un simple moment d’inattention en

utilisant un outil électrique peut entraîner des blessures corporelles graves.

• S’habiller de manière appropriée. Ne pas porter de vêtements amples ni de bijoux.

Attacher les cheveux longs. Tenir les cheveux, les vêtements et les gants hors de portée des pièces en mouvement. Les vêtements amples, bijoux ou cheveux longs

pourraient s’enchevêtrer dans les pièces mobiles. Se tenir éloigné des évents puisque ces derniers recouvrent souvent des pièces en mouvement.

• Éviter les démarrages intempestifs. S’assurer que l’interrupteur est à la position arrêt au moment de brancher l’outil. Transporter un outil alors que le doigt repose sur l’interrupteur ou brancher un outil dont l’interrupteur est à la position de marche risque de provoquer un accident.

• Retirer les clés de réglage ou les clés à ouverture fixe avant de mettre l’outil en marche. Une clé à ouverture fixe ou une clé qui est laissée attachée à une partie pivotante de l’outil peut causer des blessures corporelles.

• Ne pas trop tendre les bras. Conserver son équilibre en tout temps. Un équilibre convenable permettra de maîtriser l’outil lors de situations inattendues.

• Utiliser un équipement de sécurité. Toujours porter une protection oculaire. Selon les conditions, porter un masque antipoussière, des chaussures de sécurité antidérapantes, un casque de sécurité ou une protection auditive.

UTILISATION ET ENTRETIEN DE L’OUTIL

• Utiliser des serre-joints ou tout autre dispositif de fixation permettant de soutenir et de retenir la pièce sur une plate-forme stable. Tenir la pièce avec la main ou contre le corps

la rend instable et risque de provoquer une perte de maîtrise de l’outil.

• Ne pas forcer l’outil. Utiliser le bon outil pour votre application. L’outil approprié effectuera un meilleur travail, de façon plus sûre et à la vitesse pour laquelle il a été conçu.

• Ne pas utiliser l’outil si l’interrupteur ne fonctionne pas. Tout outil qui ne peur être contrôlé par l’interrupteur est dangereux et doit être réparé.

• Débrancher la fiche du bloc d’alimentation avant de faire quelque ajustement que ce soit, de changer d’accessoire ou de ranger l’outil. De telles mesures de sécurité préventives réduisent le risque de mettre l’outil en marche accidentellement.

• Ranger les outils inutilisés hors de portée des enfants et des personnes non formées à leur utilisation. Les outils sont dangereux entre les mains d’utilisateurs inexpérimentés.

• Entretenir les outils avec soin. S’assurer que les outils de coupe sont aiguisés et propres. Bien entretenus, les outils de coupe affûtés risquent moins de coincer et sont plus faciles à maîtriser.

élimine la nécessité d’utiliser un cordon d’alimentation muni d’une fiche

Calibre minimum pour une rallonge

+ 4 hidden pages