Epson CFS-900P User Manual

MIS Continuous Flow for Epson Photo 900
Installation Instructions

What you will need to Install the Photo 900 CFS

Complete CFS-900P Kit
Scissors
Measuring Tape or Ruler
Paper Towels
Alcohol or Cleaning Solution

What is included in your Photo 900 CFS Kit

Cartridge Set with tubes attached
Set of 6 Inks (C, Lc, M, Lm, Y, K)
6 Drilled Bottle Caps
Clear Plastic Bridge Bracket with Black Velcro
Clear Plastic Tube Support with White Adhesive Backing
1 Beige Tube Clip
6 Black Velcro Circles (Hook & Loop)
1 Piece of Loop Velcro ¾ x ¾
2 thin tie wraps.

Step 1 - Check Printer Condition

If you have a brand new printer, follow the Epson instructions for setting up your printer. Use the Epson cartridges that came with the printer. Follow normal installation instructions for the software. Test the printer by printing pictures. Learn how to use the Epson utilities to run a Nozzle pattern check and to run a Cleaning Cycle.
Make sure that the printer can produce a perfect nozzle pattern before proceeding with Permaflow installation.
If you have been using the printer in the past, just make sure it produces a perfect nozzle pattern before proceeding with the Permaflow installation. If the Nozzle pattern has any gaps whatsoever, then run cleaning cycles until it prints perfectly.
Step 2
– Disconnect Power From Printer
Push, but do not hold the INK button on the printer. This will move the cartridges to the “replacement” position. After they move to this position, which is on the left, PULL THE POWER PLUG OUT OF THE WALL. Now the cartridges can be moved from side to side by hand. We will tell you later when to reattach the printer power plug (step 9).
Step 3
– Install Tube Supports
Use your alcohol or cleaning solution and clean the top of the printer housing where the clear plastic Tube Support is going to attach. Make sure you wipe this area clean and dry before proceeding. See photo below. (The Tube Support is the clear plastic piece with the white foam tape on it.)
Use a pencil or marking pen, and mark a line on the printer housing, at 3 1/8 inches from the edge of the printer housing as shown in the above photo. This photo was taken after the tubes were installed.
Next, you will notice that the Bridge Bracket has both the Hook and Loop Velcro on it. The Hook portion of the Velcro is going to end up attached to your printer. The Loop portion will remain on the Bridge
Bracket. Do not separate the Hook and Loop, Keep them together just like they were when delivered. Remove the adhesive backing from the Hook portion of the Velcro. Keep it attached to the Loop portion. Carefully install the Bridge Bracket in its proper location at the left edge of the housing, as shown above. Keep it straight and press down firmly all along the edges. When you lift up the Bridge Bracket, after pressing it down, the Hook Velcro will remain in place on the printer.
Keep the Bridge Bracket off for now.
Step 4
- Install Protective Velcro
In the kit there is a small piece of Velcro ¾ x ¾ . Install it on the left edge of the printer in the position shown below
Step 5
– Prepare Cartridges
Prefilled Carts
On the end of the cartridge tubes, there is a black steel paper clip. Remove this clip and unfold the tubes so they lay flat. The black paper clip is no longer needed, it was just for shipping purposes. The ends of the tubes should be split so they can be separated easily. Don’t separate them now.
Empty Carts
The ends of the tubes should be split so they can be separated easily. Separate them back about 6 inches, no more.
If you ordered an empty cartridge set, you must put ink in it before it can be used. There are two ways to put ink into the carts. Fill from bottom with syringe and bottom fill adapter, or use a vacuum pump. If you fill from the bottom, then inject ink into the bottom of the cartridge until you just begin to see in at the top of the cartridge. If you are vacuum filling, follow the instructions that came with the vacuum pump.
Make sure you get the right inks in the right cartridge chambers. The cartridges are marked on top.
After filling the empty cartridges, let them sit on your bench in their installed position for at least 2 hours, so that any trapped air can rise to the top.
Loading...
+ 4 hidden pages