The Light pack contains:
The following tools may be required:
Ayres - 4CH / 6CH (Semi-Flush fittings)
Safety Warnings
INSTRUCTION M ANUAL
These products are only suitable for connection to a 240V~50Hz supply in accordance with current
IEE wiring Regulations and should be installed in accordance with local Building Regulations and
are for Domestic indoor ceiling use only and not suitable for a Bathroom location.
The light fittings should be connected to a lighting circuit protected by a 5 amp fuse (or a 6 amp
miniature circuit breaker).
If in doubt we recommend you contact a qualified electrician. Before installing your light fitting
always:
Switch off the mains supply and remove the appropriate fuse or switch off the appropriate circuit
breaker before commencing installation.
Ensure that no one else has access that would enable the supply to be inadvertently reconnected.
Never fit bulbs of a higher wattage or of a type other than those specified on the label as this may
cause overheating and damage the fitting.
These product contains glass parts – be careful during handling and maintenance to avoid
breakage.
The bulbs become hot during use so please switch off and allow 10 minutes to cool before replacing
bulbs or cleaning the fitting.
This fitting is heavy and you may require assistance in connecting it to the supply and securing it to
the mounting surface. When fixing to the mounting surface ensure that the fixings used are
appropriate for the mounting surface on which they are being used.
Clean with a dry cloth only. Do not use liquid or abrasive cleaners on this product.
If any modification is made it will invalidate the warranty and may render the product unsafe.
Before you start
Please read these instructions carefully before fitting your new light and retain for reference.
Make sure that there are no pipes or cables beneath the mounting surface.
Check the packaging and make sure that you have all the required parts.
Follow each assembly step in order to prevent incorrect assembly.
Make sure all screws / nuts, including electrical connections etc are fully tightened before use.
This type of Light Fitting may be connected to a Dimmer if a Tungsten incandescent bulb is used. If
a CFL/LED type bulb is fitted then these cannot (generally) be controlled by a dimmer.
Light fitting and mounting bracket.
Terminal connection block(s).
Shade ring tool.
G9 Bulbs.
Selection of cross and flat head screwdrivers.
Electric drill and assorted drill bits.
Wire strippers.
Electrical insulation tape.
1
Assembly/ User Instructions
Diagram A
1. Decide on the position of the light fitting / or
Diagram B
WIRING DETAILS
These assembly diagrams are intended as a guide – if in doubt consult a qualified electrician.
The same general instruction applies to the 4 and 6 light fittings.
Endon
LS9 0SE
20150907
Y11 131v3
2
remove existing light fitting. Take a note of the
position of the electrical connections. Ensure
there is a solid mounting surface, preferably a
wooden joist or joist bridge to support the
weight of the light fitting.
2. See Diagram A. Remove the fixing bracket by
undoing the 2 side screws (1), retain for re-use.
3. Use the fixing bracket (2) as a template to
mark the screw holes, mark the screw holes
and secure to the ceiling with the screws (3)
supplied.
4. Diagram B. Your fitting will be supplied `flat
packed`. To assemble the stem, screw the
bottom nipple to the hub at position (4). Then
put the decorative chrome tube over it. Next
screw the nut to the top of the thread at (5) as
shown. Finally screw the top stem to this
thread. NOTE: The internal cables will need
to be shortened. Make a note of the ter m inal
positions. (see wiring details) We suggest
that the earth cable (green/yellow) is cut to
a length of 200mm, reconnect to the earth
terminal. Shorten the live (brown) / Neutral
(blue) cables to 150mm and connect them
to their respective terminal positions.
Support your fitting and connect the house
wiring to the terminal block (6) – see wiring
details. NOTE: This is a Class I fitting and
must be earthed. The 4
connector is used for the “loop” wires of the
“Ring Circuit”. There may be more than one set
of cables in the “loop” connections. If there is a
“Ring Circuit” and you do not understand the
connections you must consult an electrician.
Any loose terminal blocks –not secured to
ceiling cup - should always be covered with 2
layers of good quality insulation tape.
5. Secure the fitting back onto the fixing bracket
with the 2 side screws (1), removed in 2 above.
Make sure that all the internal cables and
connections are inside the ceiling cup taking
care not to trap or strain the internal cables.
6. Fit the shades (7) and secure with the shade
ring (8) using the shade ring tool (9).
7. Fit the bulbs (10) into the lamp holders being
careful not to touch the bulbs with your bare
hands – use a cloth or gloves to insert the
bulbs. NOTE; Never fit bulbs of a higher
wattage or of a type other than those
provided / specified on the lab el (as these
may cause overheating and damage the
fitting).
8. Turn on the power and test.
th
terminal block
Loading...