The Light pack contains:
The following tools may be required:
96961 -WBCH and 96971-WBAB - 1 Light Wall brackets.
Safety Warnings
INSTRUCTION M ANUAL
These products are only suitable for connection to a 240V~50Hz supply in accordance with current
IEE wiring Regulations and should be installed in accordance with local Building Regulations and
are for Domestic wall use only. They are not suitable for bathroom use.
The light fitting should be connected to a lighting circuit protected by a 5 amp fuse (or a 6 amp
miniature circuit breaker).
If in doubt we recommend you contact a qualified electrician. Before installing your light fitting
always:
Switch off the mains supply and remove the appropriate fuse or switch off the appropriate circuit
breaker before commencing installation.
Ensure that no one else has access that would enable the supply to be inadvertently reconnected.
Never fit bulbs of a higher wattage or of a type other than those specified on the label as this may
cause overheating and damage the fitting.
Be careful during handling and maintenance to avoid breakage or damage to the fitting.
The bulbs become hot during use so please switch off and allow 10 minutes to cool before replacing
bulbs or cleaning the fitting.
Clean with a dry cloth only. Do not use liquid or abrasive cleaners on this product.
If any modification is made it will invalidate the warranty and may render the product unsafe.
Before you start
Please read these instructions carefully before fitting your new light and retain for reference.
Make sure that there are no pipes or cables beneath the mounting surface.
Check the packaging and make sure that you have all the required parts.
Follow each assembly step in order to prevent incorrect assembly.
Make sure all screws / nuts, including electrical connections etc are fully tightened before use.
This type of Light Fitting may be connected to a Dimmer if a Tungsten incandescent bulb is used. If
a CFL/LED type bulb is fitted then these cannot (generally) be controlled by a dimmer.
Light fitting and mounting bracket.
Terminal connection block(s).
Shade ring.
Selection of cross and flat head screwdrivers.
Electric drill and assorted drill bits.
Wire strippers.
1
Assembly/ User Instructions
D090 48
Diagram A
1. Decide on the position of your light
Diagram B
Wiring Details
These assembly diagrams are intended as a guide – if in doubt consult a qualified electrician.
fitting. Ensure there is a solid mounting
surface, preferably a brick or block wall
and ensure that there are no cables or
pipes beneath the surface. If the wall is
timber frame and plasterboard then
please use appropriate fixings. Wall
plugs are shown here – Diagram A.
Ensure the fixings used can support
the weight of the wall light.
2. Remove the fixing bracket, by undoing
the 2 back plate /bracket screws (1),
retain these for re-use.
3. Use the fixing bracket, as a template to
mark the screw holes. Make sure the
bracket is horizontal. Fix the bracket to
the wall – the use of plugs (2) and
screws (3) are shown here.
4. Diagram B. Support your fitting and
connect the house wiring to the
terminal block (4). NOTE: This is a
Class I fitting and must be earthed..
Open the terminal block box and take
out the long tailed grommet, sliding it
up the house supply cable. Cut and
strip the cable and connect it to the
terminal block as shown. See wiring
details. Re-fit the long tailed grommet.
Close the box.
5. Re-position the fitting over the wall
bracket and secure with the 2 back
plate / bracket screws, removed in 2
above. Make sure that all the internal
cables and connections are inside the
back plate taking care not to trap or
strain the internal cables.
6. Secure the shade (5) with the shade
ring (6).
7. Fit the bulb (7) into the lamp holder.
NOTE; Never fit bulbs of a higher
wattage than those specified on the
label (as these may cause
overheating and damage the fitting).
8. Turn on the power and test.
Endon Lighting
LS
9 0SE
20150904
2
Loading...