Emerson LK180 Owner's Manual

READ AND SAVE THESE INSTRUCTIONS

Ceiling Fan

Light Fixture

Owner’s Manual

Net Weight: 4.5 Lbs.

Four 13-Watt CFL Medium Base Bulbs

Model Number:

LK180

Safety Instructions

WARNING: To avoid fire, shock, and serious personal injury, follow all instructions carefully.

1.Read your Owner's Manual carefully before installing the light fixture. Retain Owner's Manual for
future reference.

2.Be careful of the fan and blades when cleaning, painting, or working near the fan. Before installing
or servicing the light fixture or ceiling fan, switch power off at service panel and lock service panel
disconnecting means to prevent power from being switched on accidentally. When the service
disconnecting means cannot be locked, securely fasten a warning device, such as a tag, to the
service panel.

3.Do not exceed the wattage indicated on fixture.

ADDITIONAL SAFETY INSTRUCTIONS FOR INSTALLATION

1.To avoid possible electrical shock be sure electricity is turned off at the main fuse or circuit breaker
box before wiring.

2.Make certain no bare wires are exposed outside the wire connectors.

3.All wiring must conform to national and local electrical codes.

4.Follow the recommended instructions for the proper method of wiring your new light fixture. If you
feel you do not have enough electrical wiring knowledge or experience, have your light fixture
installed by a licensed electrician. Any electrical work not described in this manual should be
performed by a licensed electrician.

WARNING: To reduce the risk of possible fire and electrical shock, install only on Emerson CF
Series Ceiling Fans in indoor locations. This light kit is not to be used on Emerson CF Series Ceiling
Fans installed in damp or wet locations.

Part No. F40BP74860000 Form No. BP7486
Revision: 131112 ETL Model Nos.: LK180

Questions, problems, missing parts: Before returning to the store call Emerson Electric Customer Service

8 a.m. - 6 p.m., Eastern, Monday-Friday

1-800-654-3545

www.emersonfans.com

Assembly and Installation

4. Remove the center screw from the switch cup

(Figure 1).

5. Carefully locate the white and blue wires (labeled

either "L" or "LIGHT") in the switch cup and
remove the wire connectors from the wires.

6. Insert the black and white wires from the light fitter

through the center hole in the switch cup
(Figure 2) and thread the switch cup onto the light
fitter. Hold wires taut while installing switch cup to
prevent the wires from twisting. Tighten the fitter
until the fan switch chain aligns with the hole in the
fitter.

Do not install or use the light fixture if any part
is missing or damaged. Contact your dealer for
replacement.

Figure 1

Installation on Emerson Fans

Having a Modular Switch Cup with

Center Screw

1. Remove all parts and parts packages from the

carton.

2. Remove the switch cup from the cover plate by

removing the three screws around the side of the
switch cup (Figure 1).

3. Disconnect the motor connector from the switch

cup connector (Figure 1).

WARNING

!

To avoid possible electrical shock, be sure
electricity is turned off at the main fuse or
circuit breaker box before wiring.

WARNING

!

R

S

0

Figure 2

Figure 3

WARNING: To avoid possible fire or electrical
shock, make certain no bare wire strands are
exposed outside wire connectors.

To avoid possible fire or electric shock, be careful
not to pinch wires between switch cup and the cover
plate.

WARNING

!

7. Insert the black and white wires through the lock-

washer and hex nut (supplied), firmly tighten the
hex nut to secure the light kit fitter to the switch
cup. Connect the white wire from the switch cup
to the white wire of the light fitter (Figure 2).
Connect the blue wire from the switch cup to the
black wire of the light fitter. Use listed wire
connectors (previously removed in Step 5) to
make connections (Figures 2 and 3).

8. Carefully tuck all wires and splices into the switch

cup. (Figure 2.)

9. Connect the motor connector to the switch cup

connector.

10. Position the cup/light fitter in the cover plate and

install the three screws that were previously
removed in Step 2 and tighten securely.

11. The light sockets are equipped to take four

13-watt CFL medium base bulbs.

2

ETL Model No.: LK180

MOTOR
CONNECTOR

BLACK WIRE

BLUE WIRE
HEX NUT
SCREWS

SWITCH CUP

LIGHT FITTER

COVER PLATE

SWITCH CUP
CONNECTOR

WIRE
CONNECTOR

WHITE WIRE
LOCKWASHE
FAN SWITCH

CHAIN

MOTOR
CONNECTOR

SCREWS

SWITCH
CUP

CENTER SCREW

COVER PLATE

SWITCH CUP
CONNECTOR

FILTER FLANGE
RUBBER

WASHER
HEX NUT

BOWL CAP
(FN200)

FAN SWITCH
CHAIN

FINIAL (FN20