Emerson Liebert UPStation GXT2U User Manual

AC Power Systems
For Business-Critical Continuity™

Liebert® UPStation GXT2U

User Manual - 230V, 700-3000VA

™

TABLE OF CONTENTS

1.0 IMPORTANT SAFETY INSTRUCTIONS . . . . . . . . . . . . . . . 1

2.0 GLOSSARY OF SYMBOLS . . . . . . . . . . . . . . . . . . . . . . . 3

3.0 INTRODUCTION. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

4.0 MAJOR COMPONENTS . . . . . . . . . . . . . . . . . . . . . . . . . 5

4.1 Transient Voltage Surge Suppression (TVSS)

and EMI/RFI Filters. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

4.2 Rectifier/Power Factor Correction (PFC) Circuit . . . . . . 5

4.3 Inverter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

4.4 Battery Charger . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

4.5 DC to DC Converter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

4.6 Battery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

4.7 Dynamic Bypass . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

5.0 INSTALLATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

5.1 Preparation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

5.2 Tower UPS Installation . . . . . . . . . . . . . . . . . . . . . . . . . . 8

5.3 Rack-Mount UPS Conversion and Installation . . . . . . . 9

5.4 External Battery Cabinet Installation . . . . . . . . . . . . . 13

6.0 CONTROLS AND INDICATORS . . . . . . . . . . . . . . . . . . . 14

6.1 ON/Alarm Silence/Manual Battery Test Button . . . . . 14

6.2 Standby/Manual Bypass Button . . . . . . . . . . . . . . . . . . 15

6.3 Load/Battery Level Indicators (4 Green, 1 Amber) . . . 15

6.4 Fault Indicator LED (Red). . . . . . . . . . . . . . . . . . . . . . . 15

6.5 Bypass Indicator LED (Amber) . . . . . . . . . . . . . . . . . . . 15

6.6 UPS ON Indicator LED (Green) . . . . . . . . . . . . . . . . . . 15

6.7 Battery Indicator LED (Amber). . . . . . . . . . . . . . . . . . . 16

6.8 AC Input Indicator LED (Green). . . . . . . . . . . . . . . . . . 16

6.9 Output Voltage Selection . . . . . . . . . . . . . . . . . . . . . . . . 16

i

7.0 OPERATING INSTRUCTIONS . . . . . . . . . . . . . . . . . . . . 17

7.1 Normal Mode Operation . . . . . . . . . . . . . . . . . . . . . . . . 17

7.2 Bypass Mode Operation . . . . . . . . . . . . . . . . . . . . . . . . . 17

7.3 Battery Mode Operation . . . . . . . . . . . . . . . . . . . . . . . . 18

7.4 Battery Recharge Mode . . . . . . . . . . . . . . . . . . . . . . . . . 18

8.0 COMMUNICATIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

8.1 Communications Interface Port. . . . . . . . . . . . . . . . . . . 19

8.2 Pins 4 & 5 - Remote Shutdown on Battery . . . . . . . . . . 19

8.3 Pins 5 & 6 - Any-Mode Shutdown . . . . . . . . . . . . . . . . . 20

8.3.1 Auto-Enable Output . . . . . . . . . . . . . . . . . . . . . . . . . . 20

8.3.2 Pin 6 Logic . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20

8.4 UPS Intelligent Communications . . . . . . . . . . . . . . . . . 21

9.0 CONFIGURATION PROGRAM . . . . . . . . . . . . . . . . . . . . 22

9.1 Liebert UPStation GXT2U Configuration Program

Abilities . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22

9.1.1 What You Will Need . . . . . . . . . . . . . . . . . . . . . . . . . . 22

10.0 MAINTENANCE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

10.1 Battery Replacement . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

10.1.1 Internal Battery Replacement Procedures . . . . . . . . 24

11.0 TROUBLESHOOTING . . . . . . . . . . . . . . . . . . . . . . . . . . 25

12.0 SPECIFICATIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30

12.1 Battery Cabinet Specifications . . . . . . . . . . . . . . . . . . . 32

13.0 BATTERY RUN TIMES. . . . . . . . . . . . . . . . . . . . . . . . . 33

13.1 Product Warranty Registration. . . . . . . . . . . . . . . . . . . 34

ii

Important Safety Instructions

1.0 IMPORTANT SAFETY INSTRUCTIONS

WARNING

!

Opening or removing the cover may expose you to lethal
voltages within this unit even when it is apparently not
operating and the input wiring is disconnected from the
electrical source. Observe all cautions and warnings in this
manual. Failure to do so MAY result in serious injury or
death. Refer all UPS and battery service to qualified service
personnel. Do not attempt to service this product yourself.
Never work alone.

SAVE THESE INSTRUCTIONS

This manual contains important safety instructions. Read all safety,
installation, and operating instructions before operating the Uninter­ruptible Power System (UPS). Adhere to all warnings on the unit and
in this manual. Follow all operating and user instructions. Individuals
without previous training can install and operate this equipment.

It is not intended for use with life support and other designated “criti­cal” devices. Maximum load must not exceed that shown on the UPS
rating label. The UPS is designed for data processing equipment. If
uncertain, consult your local dealer or Liebert representative.

This UPS is designed for use on a properly earthed (grounded), 50 Hz
or 60Hz, 230V supply (programmable for 200, 208, 220, 230, and
240VAC output). Installation instructions and warning notices are
located in this manual.

ELECTROMAGNETIC COMPATIBILITY—The Liebert UPStation
GXT2U
2004/108/EC and the published technical standards. Continued com­pliance requires installation in accordance with these instructions and
use of manufacturer approved accessories only.

Operate the UPS in an indoor environment only in an ambient tem­perature range of 0°C to +40°C (32°F to +104°F). Install it in a clean
environment, free from conductive contaminates, moisture, flammable
liquids, gases and corrosive substances.

™

Series complies with the requirements of the EMC directive

WARNING

!

This UPS should not be supplied from electrical power
systems of the “IT” (Impedance á Terre) type
(IEC 364 - Electrical Installation of Buildings).

1

Important Safety Instructions

This UPS contains no user serviceable parts except the internal bat­tery pack. The UPS ON/Standby push buttons do not electrically iso­late internal parts. Under no circumstances attempt to gain access
internally other than to replace the batteries due to risk of electric
shock or burn. Do not continue to use the UPS if the front panel indi­cations are not in accordance with these operating instructions or if
the UPS performance alters in use. Refer all faults to your local
dealer, Liebert representative or the Liebert Worldwide Support
Group.

Servicing of batteries should be performed or supervised by personnel
knowledgeable of batteries and the required precautions. Keep unau­thorized personnel away from the batteries. PROPER DISPOSAL OF
BATTERIES IS REQUIRED. REFER TO YOUR LOCAL LAWS AND
REGULATIONS FOR BATTERY DISPOSAL REQUIREMENTS.

Never block or insert any object into the ventilation holes or other
openings of the UPS.

DO NOT CONNECT equipment that could overload the UPS or
demand half-wave rectification from the UPS, for example: electric
drills, vacuum cleaners, laser printers or hairdryers.

Storing magnetic media on top of the UPS may result in data loss or
corruption.

Turn the UPS off and isolate the UPS before cleaning; use only a soft
cloth, never liquid or aerosol cleaners. Keep the front and rear vents
free of dust accumulation that could restrict airflow.

When replacing batteries, replace with the same Liebert authorized
replacement battery kits.

CAUTION

!

Do not dispose of battery or batteries in a fire. The battery
may explode.

Do not open or mutilate the battery or batteries. Released
electrolyte is harmful to skin and eyes. It may be toxic.

CAUTION

!

A battery can present a risk of electrical shock and high short
circuit current. The following precautions should be observed
when working on batteries:

• Remove watches, rings, and other metal objects.

• Use tools with insulated handles.

2

2.0 GLOSSARY OF SYMBOLS

•

Risk of electrical shock

Indicates caution followed by important instructions

AC input

AC output

Glossary of Symbols

i

Requests the user to consult the manual

Indicates the unit contains a valve-regulated lead acid
battery

Recycle

DC voltage

Equipment grounding conductor

Bonded to ground

AC voltage

ON

Standby

3

Introduction

3.0 INTRODUCTION

Congratulations on your choice of the Liebert UPStation GXT2U™
Uninterruptible Power System (UPS). It provides conditioned power
to microcomputers and other sensitive electronic equipment.

Upon generation, AC power is clean and stable. However, during
transmission and distribution it may be subject to voltage sags,
spikes, or complete power failure that may interrupt computer opera­tions, cause data loss, or even damage equipment. The Liebert UPSta­tion GXT2U protects equipment from these disturbances.

The Liebert UPStation GXT2U comes in nominal power ratings of
700, 1000, 1500, 2000 and 3000 VA. Complete model specifications
appear at the end of this manual (see 12.0 - Specifications).

The Liebert UPStation GXT2U is a compact, “on-line” UPS. An on-line
UPS continuously conditions and regulates its output voltage,
whether mains power is present or not. It supplies connected equip­ment with clean sinewave power. Sensitive electronic equipment oper­ates best from sinewave power.

For ease of use, the Liebert UPStation GXT2U features a light-emit­ting diode (LED) display to indicate either load percentage or battery
capacity depending upon the mode of operation. It also provides self­diagnostic tests, a combination ON/Alarm Silence/Manual Battery
Test button, a Standby button, user configurable program, and two
levels of alarms when the unit is operating on battery.

The Liebert UPStation GXT2U has an interface port for communica­tion between the UPS and a network server or other computer sys­tems. This port provides detailed operating information including
voltages, currents, and alarm status to the host system when used in
conjunction with Liebert MultiLink™ software. Liebert MultiLink
software can also remotely control UPS operation.

4

4.0 MAJOR COMPONENTS

Major Components

Input Output

L

N
G

TVSS &
EMI/RFI

Battery

Charger

Rectifier

Dynamic

Bypass

Inverte

DC to DC

Converter

Battery

4.1 Transient Voltage Surge Suppression (TVSS)
and EMI/RFI Filters

L

N

G

These UPS components provide surge protection and filter both elec­tromagnetic interference (EMI) and radio frequency interference
(RFI). They minimize any surges or interference present in the mains
line and keep the sensitive equipment protected.

4.2 Rectifier/Power Factor Correction (PFC) Circuit

In normal operation, the rectifier/power factor correction (PFC) circuit
converts mains AC power to regulated DC power for use by the
inverter while ensuring that the waveshape of the input current used
by the UPS is near ideal. Extracting this sinewave input current
achieves two objectives:

• The mains power is used as efficiently as possible by the UPS.

• The amount of distortion reflected on the mains is reduced.

This results in cleaner power being available to other devices in the
building not being protected by the Liebert UPStation GXT2U.

4.3 Inverter

In normal operation, the inverter utilizes the DC output of the power
factor correction circuit and inverts it into precise, regulated sinewave
AC power. Upon a mains power failure, the inverter receives its
required energy from the battery through the DC to DC converter. In
both modes of operation, the UPS inverter is on-line and continuously
generating clean, precise, regulated AC output power.

5

Major Components

4.4 Battery Charger

The battery charger utilizes energy from the mains power and pre­cisely regulates it to continuously “float charge” the batteries. The bat­teries are being charged whenever the Liebert UPStation GXT2U is
plugged in, even when the UPS is not turned on.

4.5 DC to DC Converter

The DC to DC converter utilizes energy from the battery system and
raises the DC voltage to the optimum operating voltage for the
inverter. This allows the inverter to operate continuously at its opti­mum efficiency and voltage, thus increasing reliability.

4.6 Battery

The Liebert UPStation GXT2U utilizes valve-regulated, nonspillable,
lead acid batteries. To maintain battery design life, operate the UPS
in an ambient temperature of 20°C to 25°C (68°F to 77°F). Optional
external battery cabinets are available to extend battery run times.

4.7 Dynamic Bypass

The Liebert UPStation GXT2U provides an alternate path for mains
power to the connected load in the unlikely event of a UPS malfunc­tion. Should the UPS have an overload, overtemperature, or UPS fail­ure condition, the UPS automatically transfers the connected load to
bypass. Bypass operation is indicated by an audible alarm and illumi­nated amber Bypass LED (other LEDs may be illuminated to indicate
the diagnosed problem). To manually transfer the connected load from
the inverter to bypass, press the Standby button once.

NOTE

The bypass power path does NOT protect the connected
equipment from disturbances on the mains supply.

6

Figure 1 Liebert UPStation GXT2U, Rear View

Major Components

DB-9

Communications

Port

Rev. USBCARD

USB card being fitted
in Liebert IntelliSlot

®

Port

Cooling Fans

External Battery
Connector

Output
Sockets

Support Base

Circuit Protector

Mains Input

7

Installation

5.0 INSTALLATION

5.1 Preparation

1. Visually inspect the UPS for freight damage. Report damage to

the carrier and your local dealer or Liebert representative.

CAUTION

!

The UPS is heavy (see 12.0 - Specifications section). Take
proper precautions when lifting or moving it.

2. Decide where to place the Liebert UPStation GXT2U. Install the

UPS indoors in a controlled environment, where it cannot be
accidentally turned off. Place it in an area of unrestricted airflow
around the unit, away from water, flammable liquids, gases,
corrosives, and conductive contaminants. Maintain a minimum
clearance of 100mm (4 in.) in the front and rear of the UPS.
Maintain an ambient temperature range of 0°C to 40°C (32°F to
104°F).

NOTE

UPS operation in temperatures above 25°C (77°F) reduces
battery life.

3. The Liebert UPStation GXT2U may be installed in either a tower

configuration or in a rack, depending on available space and use
considerations. Determine the type of installation and follow the
appropriate instructions in either 5.2 - Tower UPS Installation
or 5.3 - Rack-Mount UPS Conversion and Installation.

5.2 Tower UPS Installation

When using the Liebert UPStation GXT2U in a tower configuration,
use the included support base (shown below, left) to stabilize the UPS.

If any battery cabinets are added, they will include spacers to accom­modate the additional cabinets (shown below, right).

Support base Spacers added to support

base to accommodate

additional battery cabinets

8

Installation

5.3 Rack-Mount UPS Conversion and Installation

NOTE

When rack mounted, the UPS must be supported by a shelf,
brackets or slide rails on each side. The rack mount handles
WILL NOT support the weight of the UPS. They are used to
move the UPS into and out of the rack.

1. For slide rail installations, first remove the top/side fin. Slide the

top/side fin forward, then lift it up to remove. If desired, install the
optional rack mount handles that were shipped with the UPS.

UPStation

GXT

–

+

AC INPUT

BATTERY

UPS ON

BYPASS

Optional rack mount handles

Securing hardware and slide rails are sold separately. Contact
your local dealer or Liebert representative for these additional
options and any assistance needed.

2. Unpack the two (2) rack-

mounting bracket assemblies
and mounting hardware
from the rack-mounting kit
(P/N: RMKIT18-32). Bracket

Retaining
latches

assemblies are
interchangeable between
left-hand or right-hand.
Remove inner member of
each bracket assembly as
shown at right by extending
it to its outermost position,

Inner
members

Front
members

depressing the retaining
latch and then pulling inner member from bracket assembly.

Return
flanges

Rear
members

9

Installation

3. Determine the height position inside the rack enclosure where you

want to mount the UPS or battery cabinet.

CAUTION

!

Reduce risk of tipping the rack enclosure by placing UPS or
battery cabinet in the lowest possible rack position.

Install rear member of each
bracket assembly into rack
enclosure with two (2) M5

Front rack
mounting rails

M5 screws

screws provided in this kit.
(See figure at right.) Return
flanges on bracket assembly
fit to the inside of rack
mounting rails. Insert
screws loosely (finger-tight)
into top and bottom holes of
return flange on rear mem­ber. Extend bracket assem-

M5 screws

Rear rack
mounting
rails

bly by sliding front member
forward until it touches the front rack mounting rail. Insert two (2)
M5 screws loosely (finger-tight) into top and bottom holes of return
flange on each front member. Make sure bracket assemblies are at
the same mounting height on all four (4) rack mounting rails.

4. Locate eight (8) M4 screws and eight (8) M4 nuts from hardware

pack in this kit. Each nut has a locking, nylon insert that begins
gripping the screw when it is halfway tight. Make sure to tighten
nut and screw completely to assure locking action. Fasten rear
member and front member together using four (4) screws and four
(4) nuts per bracket assembly as shown in the figures below. For
maximum support, locate fasteners for each bracket assembly as
far apart as possible, depending on rack depth, while still joining
both members (See figures below). Check alignment of bracket
assemblies and TIGHTEN ALL SCREWS FROM Steps 3 and 4.

M4 nuts

M4
screws

M4 nuts

M4
screws

18" rack
depth

32" rack
depth

M4 nuts

M4 nuts

10

Installation

Retaini

h

5. Prepare the UPS or battery

M4 screws

ng latc

cabinet (the “equipment”) for
rack mounting by following
instructions in the
equipment’s user manual. The
equipment may require

UPS or battery
cabinet

additional parts to be added or
parts to be removed for rack
mounting. After it is prepared,
lay equipment in rack­mounting position. Fasten
inner members from Step 2 to

Front

M4 screws

the equipment on both sides
as shown in the figure at right with (8) M4 screws provided in this
kit. Make sure retaining latch is near the rear of the equipment as
shown in the figure at right.

6. Open grease packet

provided in this kit. Apply
a 1" long bead of grease
four (4) places inside the
bottom, curved tracks of

UPS or
battery
cabinet

Apply
grease

front members as shown at
right. The grease will allow
the equipment to slide into
the bracket assemblies
more easily.

Apply
grease
(inside)

CAUTION

!

Lifting equipment into rack may be a two-person job,
depending on weight of equipment. See equipment’s user
manual.

7. Insert the equipment, with inner members attached from Step 5,

into bracket assemblies by inserting top and bottom edges of inner
members into the top and bottom, curved tracks of front members
and sliding the equipment into rack (see figure in Step 6). Ends of
inner members are tapered to allow rear of the equipment to be
angled upward before insertion, if space allows.

Then the rear, bottom edges of inner
members can be placed into front
edge of bottom tracks, and the front of
the equipment can be tipped up into
horizontal position to insert the top
edges of inner members before sliding
the equipment into rack (see figure at right). The equipment
should move smoothly into bracket assemblies. If not, recheck
alignment of front and rear members from Steps 3 and 4.

11

Installation

8. Secure front of the equipment to rack mounting rails to prevent

the equipment from sliding out of position. If securing holes are
provided on front of the equipment that align with the center holes
on return flange of front members, you can use the four (4) extra
M5 screws provided in this kit to secure the equipment.
Otherwise, the equipment should be secured to front of rack
mounting rails with four (4) customer-supplied fasteners.

9. To orient the display for

horizontal viewing, remove the
front plastic bezel by pulling
forward evenly on both sides.
The unit has two front panel

Vertical
overlay
for
tower
UPS

Horizontal overlay
for rack UPS

overlays. Remove the outer
overlay (used for tower
installation). This reveals a
horizontally oriented front
panel overlay for rack
mounting. Snap the front bezel
back into place.

10. Once the UPS is installed in

UPStation GXT

+

–

UPStation GXT

+

–

AC INPUT BATTERY UPS ON BYPASS

AC INPUT BATTERY UPS ON BYPASS

the rack, the load may be
connected. Ensure the load
equipment is turned off; plug
all loads into the output
sockets on the rear of the UPS.

11. The input supply cable should

be connected to the electrical
supply distribution in
accordance with local rules and conditions.

12. Turn ON the UPS by pressing the ON button; then turn on the

connected load equipment. The UPS is now providing conditioned
power to your equipment.

12

Installation

5.4 External Battery Cabinet Installation

Optional Liebert external battery cabinets may be connected to the UPS
to provide additional battery run time. External battery cabinets are
designed to be placed all on one side of the UPS or stacked beneath the
UPS. There is no limit to the number of external battery cabinets that
can be used but each cabinet will increase the battery recharge time.

CAUTION

!

The external battery cabinet(s) are heavy (see

12.0 - Specifications). External battery cabinets can be used
in rack-mount or tower configuration. Take proper precautions
when lifting them.

1. Visually inspect the external battery cabinet for freight damage.

Report damage to the carrier and your local dealer or Liebert
representative.

2. For slide rail installations, first remove the top/side fin. Top/side

fin slides forward and then lift up to remove. Optional rack-mount
handles are shipped with the external battery cabinet and may be
installed at this time if desired.

3. Securing hardware and slide rails are sold separately. Please

contact your local dealer or Liebert representative for these
additional options and any assistance needed. Fasten the slides
into position with the screws per the instructions included with
the slide rails.

4. Use the enclosed support bases for the

tower option to prevent tip-over. One
additional set of support base
extensions ships with each external
battery cabinet.

5. Connect the supplied external battery

cabinet cable to the rear of the
external battery cabinet, then to the
rear of the UPS.

Rev. USBCARD

6. Turn ON the battery breaker on the

rear of the external battery cabinet.

7. The UPS is now equipped with

additional backup battery run time.
For approximate battery run times,
refer to 13.0 - Battery Run Times.

NOTE

You must use the included Configuration Program to specify
the number of external battery cabinets connected to the UPS.
For more information, see 9.0 - Configuration Program.

13

6.0 CONTROLS AND INDICATORS

All LEDs illuminated

for illustrative purposes only.

Controls and Indicators

6.1 ON/Alarm Silence/Manual Battery Test Button

This button controls output power to connected load(s) and has
three functions:

•ON

•Alarm Silence

•Manual Battery Test

ON - Pressing this button will start up the UPS in order to provide
conditioned and protected power.

Alarm Silence - To silence alarms, press this button for at least one
second. After the alarm is silenced, the Liebert UPStation GXT2U will
reactivate the alarm system to alert of additional problems.

NOTE

The LOW BATTERY and BYPASS reminder alarms CANNOT
be silenced.

Manual Battery Test - To initiate a manual battery test, press the
ON button for at least one second while operating from mains power
with no alarm conditions present.

• If only three of the five Battery LEDs illuminate, allow the UPS to
recharge the batteries for 24 hours.

• After 24 hours, retest the batteries.

• After the batteries have been retested, if only three of the five Bat­tery LEDs illuminate, contact your local dealer, Liebert represen­tative or Liebert Worldwide Support Group.

14

Controls and Indicators

6.2 Standby/Manual Bypass Button

This button controls output power to connected load(s) and has
dual functions: Standby and Manual Bypass.

CAUTION

!

While the UPS is in Normal Mode operation, pressing the
Standby/ Manual Bypass button once will put the UPS into
Bypass Mode.

Once the UPS is in Bypass Mode operation, press the Standby/
Manual Bypass button two distinct times (for about one
second each time) to turn off the UPS. Perform all necessary
shutdown procedures on connected loads before turning off the
UPS.

6.3 Load/Battery Level Indicators (4 Green, 1 Amber)

The load/battery level indicators have dual functions. During normal
mode operation LED indicators display the approximate electrical
load placed upon the UPS; and during battery mode operation LED
indicators display approximate battery capacity.

The Liebert UPStation GXT2U is equipped with automatic and
remote battery test features. The automatic test occurs every 14 days
(this option is user configurable) if mains has not been interrupted.
Should the battery fail this test, the red Fault indicator LED along
with the A and C diagnostic LEDs will illuminate and an alarm will
sound (refer to 11.0 - Troubleshooting). The remote test feature
functions with Liebert MultiLink 3 software and can remotely initiate
the battery test.

6.4 Fault Indicator LED (Red)

The Fault indicator LED is illuminated if the UPS has detected a
problem. Also, one or more of the load/battery level indicators may be
illuminated (refer to 11.0 - Troubleshooting).

6.5 Bypass Indicator LED (Amber)

The Bypass indicator LED is illuminated when the UPS is operating
from bypass power. An alarm will sound indicating the UPS detected
a problem, or the manual bypass function has been activated.

6.6 UPS ON Indicator LED (Green)

The UPS ON indicator LED is illuminated when the UPS inverter is
operating and supplying power to your connected loads.

15

Controls and Indicators

6.7 Battery Indicator LED (Amber)

The Battery indicator LED is illuminated when the UPS is operating
on battery.

6.8 AC Input Indicator LED (Green)

The AC Input indicator LED is illuminated when mains power is
available and within the input specifications.

6.9 Output Voltage Selection

The Output Voltage is user configurable and is designed to allow
selecting or changing the desired output voltage to match the mains
via the Liebert UPStation GXT2U Configuration Program provided
with the UPS. The settings to choose from are 200, 208, 220, 230, and
240 VAC output. The factory default setting is 230 VAC.

CAUTION

!

Never change the voltage settings while the UPS is ON and
powering connected loads.

NOTE

Setting output voltage to 200 VAC will cause the UPS unit to
be derated (700/1000 VA to 90%, 1500/2000/3000 VA to 80%)
of the VA and watt ratings listed in 12.0 - Specifications.

16

Operating Instructions

7.0 OPERATING INSTRUCTIONS

7.1 Normal Mode Operation

During normal operation,
mains power provides energy
to the UPS. The filters, power
factor correction circuit and
the inverter process this

AC INPUTBATTERY UPS ON BYPASS

Normal Mode Operation at 26-50%

The four green load level LEDs indicate an approximate level of load
in 25% increments. If the UPS becomes loaded beyond full rating, the
fifth (amber) LED indicator will illuminate and the UPS will sound an
audible alarm. The display template indicates the percentage of load
(26-50% of load shown in the example above) on the UPS output.

power to provide computer
grade power to connected
loads. The UPS maintains
the batteries in a fully
charged state.

7.2 Bypass Mode Operation

Bypass mode occurs when
the OFF button is pressed
once while the UPS is in Nor­mal Mode. During bypass
operation, mains power pro-

AC INPUTBATTERY UPS ON BYPASS

Bypass Mode Operation at 26-50%

The four green load level LEDs indicate an approximate level of load
in 25% increments. If the UPS becomes loaded beyond full rating, the
fifth (amber) LED indicator will illuminate and the UPS will sound an
audible alarm. The display template indicates the percentage of load
(26-50% of load shown in the example above) on the UPS output.

vides energy to the UPS. The
mains power bypasses the
inverter and provides power
for the connected load.

CAUTION

!

Turning OFF the UPS while in bypass mode will result in loss
of output power.

17

Operating Instructions

7.3 Battery Mode Operation

Battery mode occurs in
event of an extreme input
voltage condition or com­plete mains failure. The
battery system supplies
power through the DC to
DC converter to the
inverter to generate power
for the connected load.

During battery mode an alarm sounds every 10 seconds. This will
change to two beeps every 5 seconds when the battery runs low
(approximately 2 minutes remaining, but this is user configurable).
The AC Input LED will extinguish, and the Battery LED will illumi­nate to warn that a mains problem has occurred. Each battery level
indicator represents a 20% capacity level. As capacity decreases, fewer
indicators remain illuminated. Refer to 11.0 - Troubleshooting.

AC INPUTBATTERY UPS ON BYPASS

Battery Mode Operation at 80-61%

For approximate battery run times, refer to 13.0 - Battery Run
Times. These times are approximates based on resistive load and an

ambient temperature of 25°C (77°F). To increase this time, turn off
non-essential pieces of equipment (such as idle computers and moni­tors) or add the optional external battery cabinet.

CAUTION

!

Turning OFF the UPS while in battery mode will result in loss
of output power.

7.4 Battery Recharge Mode

Once mains power is restored, the UPS resumes normal operation. At
this time, the Battery Charger begins recharging.

18

Communications

r

8.0 COMMUNICATIONS

8.1 Communications Interface Port

The Liebert UPStation GXT2U UPS has a standard DB-9 serial port
female connector located on the rear of the UPS unit. Several signals
are provided on this port and are assigned as follows:

Pin Assignment Description

1 Low Battery (open collector)
2 UPS TxD (typical RS-232 levels)
3 UPS RxD (typical RS-232 levels)
4 Remote Shutdown (5-12VDC, 10-24 mA max); battery operation
5 Common
6 Remote Shutdown (short to pin 5); all modes of operation
7 Low Battery (open emitter)
8 Mains Fail (open emitter)
9 Mains Fail (open collector)

Pin Assignment Collector to Emitter*

6789

330 Ohms

54321

* Maximum voltage and current on pins 1, 7, 8, and 9 is 60VDC; 10.0 mA.

(+)

(-)

Open
Collecto

Open
Emitter

8.2 Pins 4 & 5 - Remote Shutdown on Battery

This pin is functional only when the UPS is in battery mode. If the UPS
is being powered by the mains, Pin 4 will ignore any signal on this pin.

Pin 4 requires a 5-12 VDC signal to shutdown. This normally comes
form the serial port using Liebert’s contact closure cable. It cannot be
used with just a contact closure unless the relay is used to switch a
voltage source. A 5-12 VDC signal for 1.5 seconds or greater is
required to signal a shutdown. Signals for less than 1.5 seconds will be
ignored. After Pin 4 receives a shutdown signal for 1.5 seconds, the
command cannot be canceled.

A battery shutdown signal on Pin 4 will NOT cause an immediate shut­down. A shutdown signal will start a 2-minute shutdown timer. The
timer cannot be stopped. After 2 minutes, the UPS will shut down.

19

Communications

If the mains returns during the 2-minute timer countdown, the shut­down timer will continue until the end of 2 minutes and the UPS will
turn OFF. The UPS must remain OFF for at least 10 seconds even if
AC input power returns before the UPS turns OFF. This serves to
reset and restart the server.

Whether the UPS turns back ON when power is restored depends on
the auto-restart setting: enabled or disabled.

If the auto-restart is disabled, the UPS will not restart after perform­ing the 2-minute shutdown delay.

8.3 Pins 5 & 6 - Any-Mode Shutdown

Pin 6 of the 9-pin communication connector is used for “Any-Mode
Shutdown” of the UPS output. This control input may be used in spe­cial applications to disable the UPS output power—both Inverter and
Bypass.

The Options tab allows the behavior of the Any-Mode Shutdown fea­ture to be modified. When the program opens, or the REFRESH but­ton is pressed, the UPS setting is read by the configuration program
and displayed.

8.3.1 Auto-Enable Output

WARNING

!

Note that when this option is selected and the UPS output is
disabled using Pin 6, the UPS output can turn on
automatically and without warning if the Pin 6 connection is
changed.

8.3.2 Pin 6 Logic

WARNING

!

DO NOT CHANGE THIS OPTION from the factory default
setting unless you are ready to install a normally-closed
connection between Pins 5 & 6. This connection must be
maintained to use the UPS or to use the configuration
program again, including the ability to change the UPS
setting back to the default setting using the configuration
program via a serial communication link.

If version 1.6 (or later) is used with an earlier Liebert UPStation
GXT2U model (with an earlier UPS firmware version), the Any-Mode
Shutdown features cannot be changed.

If the configuration program is used with an earlier UPS model (with
an earlier UPS firmware version) that does not support the modifica­tion of these settings, the Options tab will display a reminder of the
factory default settings. These cannot be changed.

20

Communications

8.4 UPS Intelligent Communications

The Liebert UPStation GXT2U is equipped with a Liebert IntelliSlot®
port to provide advanced communication and monitoring options.

Liebert’s MultiLink software continually monitors the UPS and can
shut down your computer or server in the event of an extended power
failure.

Liebert MultiLink can also be configured for use without the serial
cable when the Liebert IntelliSlot SNMP/Web card is installed in the
UPS. Additionally, Liebert MultiLink can be configured to coordinate
shutdown across the network with other computers running Liebert
MultiLink when you purchase a Liebert MultiLink License Kit. For
more information about the Liebert IntelliSlot SNMP/Web Card and
Liebert MultiLink License Kits, visit our Web site (www.liebert.com)
or contact your local dealer or Liebert representative.

Several option cards are available for use in the Liebert IntelliSlot
port of the Liebert UPStation GXT2U. The Liebert IntelliSlot SNMP/
Web Card provides SNMP and Web-based monitoring and control of
the UPS across the network.

The Liebert IntelliSlot MultiPort 4 Card allows you to install Liebert
MultiLink software on four computers and coordinate shutdown in the
event of a power failure.

The Liebert IntelliSlot Relay Card provides dry contact relay outputs
for custom-wired applications and delivers support for built-in shut­down for AS/400 systems.

CAUTION

!

To maintain safety (SELV) barriers and for electromagnetic
compatibility, signal cables should be segregated and run
separate from all other power cables, where applicable.

21

Configuration Program

9.0 CONFIGURATION PROGRAM

This is a new feature included with the new Liebert UPStation
GXT2U line. Several UPS settings that were previously not available
or required custom manufacturing may now be modified using this
program. For most users, the factory default settings will be adequate.
This manual illustrates the features available for modification, as well
as the factory default setting.

NOTE

The UPS must be turned off—and not powering connected equip­ment—before you make any changes to configuration settings.

While the UPS is in Normal Mode operation, press the OFF
button once to put the UPS into Bypass Mode.

Once the UPS is in Bypass Mode operation, press and release
the OFF button two distinct times (for about a second each
time) to turn off the UPS.

9.1 Liebert UPStation GXT2U Configuration Program
Abilities

• Select one of five output voltages to match voltages found around
the world.

• Enable/Disable Auto-Restart.

• Select frequency converter operation with a fixed output frequency
of 50 or 60 Hz.

• Set the Low Battery Warning alarm time from 2 to 30 minutes.

• Enable/Disable the Auto-Battery test.

• Set the Auto-Battery test to 7, 14, 21, or 28 days.

• Select the number of external battery cabinets connected to the
UPS to adjust the remaining run time calculations reported by
Liebert software products.

• Modify the shutdown setting of DB-9 pin 6 (for information on pin
assignments, see 8.0 - Communications).

NOTE

This program is compatible with UPS models beginning with
“GXT2-”, as in “GXT2-1500RT230.” It is not compatible with
earlier versions of Liebert UPStation GXT UPS.

9.1.1 What You Will Need

In addition to the Liebert UPStation GXT2U UPS, you will need the
configuration program diskette and serial cable (beige or tan, 3-wire:
GND, TX, RX; straight through 2-2, 3-3, 5-5) included in the UPS
accessory box. The BLACK ML9P9S CONTACT CLOSURE communi­cation cable IS NOT compatible with the configuration program. A
Windows 95
required to set up and run the configuration program.

®

, 98®, or NT® computer—desktop or laptop—is also

22

Maintenance

10.0 MAINTENANCE

The Liebert UPStation GXT2U requires very little maintenance. The
batteries are valve-regulated, nonspillable, lead acid and should be
kept charged to obtain their designed life. The UPS continuously
charges the batteries when connected to the mains supply.

When storing the UPS for any length of time, it is recommended to
plug the UPS in for at least 24 hours every four to six months to
ensure full recharge of the batteries.

The Liebert UPStation GXT2U is designed to allow the user to safely
replace the internal batteries. Read the safety cautions before pro­ceeding. Contact your local dealer or Liebert representative to obtain
the appropriate replacement battery kit part number and pricing.

10.1 Battery Replacement

CAUTION

!

A battery can present a risk of electrical shock and high short
circuit current. The following precautions should be observed
before replacing the batteries:

• Remove rings, watches, or other metal objects.

• Use a Phillips (crosshead) screwdriver with insulated grips.

• Do not lay tools or other metal objects on top of the batteries.

• If the battery replacement kit is damaged in any way or
shows signs of leakage, contact your local dealer or Liebert
representative immediately.

• Do not dispose of batteries in a fire. The batteries may
explode.

23

Maintenance

10.1.1 Internal Battery Replacement Procedures

1. Gently remove the front plastic bezel cover from the UPS.

2. Loosen and remove the four screws on the front battery door. Lay
the battery door aside for reassembly.

3. Gently pull battery wiring out and disconnect the two slotted
battery connectors.

4. Grasp the battery pack assembly, and pull it out of the front of the
UPS.

5. Unpack the new battery assembly taking care not to destroy the
packing. Compare new and old battery assemblies to make sure
they are the same. If so, proceed with Step 6; otherwise STOP and
contact your local dealer, Liebert representative, or the Liebert
Worldwide Support Group.

6. Line up and slide in the new replacement battery pack.

7. Reconnect the two slotted battery connectors and gently push the
battery wiring and battery pack assembly back into the UPS.

8. Reattach the front battery door with the four screws.

9. Reattach the front plastic bezel cover to the UPS.

NOTE

These are hot-swappable replacement batteries. However,
caution should be exercised because during this procedure the
load is unprotected from disturbances and power outages.

24

Troubleshooting

11.0 TROUBLESHOOTING

The information below indicates various symptoms a user may
encounter in the event the Liebert UPStation GXT2U develops a prob­lem. Use this information to determine whether external factors
caused the problem and how to remedy the situation.

1. The Fault indicator will illuminate, indicating the UPS detected a
problem.

2. An alarm will sound, alerting that the UPS requires attention.

3. One or more additional load/battery level LED indicators will be
illuminated to provide a diagnostic aid to the operator, as
described below:

Fault

E

D

C

B

A

BYPASS

UPS ON

BATTERY

AC
INPUT

This example shows the UPS
on bypass due to output overload.

ABC DEFault

AC INPUT BATTERY UPS ON BYPASS

LOAD/BATTERY

LEVEL INDICATORS

LED status Diagnosis/Audible alarm

All LEDs On bypass due to output overload; beep every half-second
A LED On bypass due to overtemperature condition; beep every 4 sec.
B LED On bypass due to DC bus overvoltage; beep every 4 sec.
C LED On bypass due to control power supply failure; beep every 4 sec.
D LED On bypass due to PFC failure; beep every 4 sec.
E LED On bypass due to inverter failure; beep every 4 sec.
A&C LEDs UPS failed battery test; long beep every minute
C&E LEDs UPS shutdown due to command from communication port

(SNMP); no beep

Battery LED
Flashing

AC LED
Flashing

Bypass LED
Flashing

Internal Battery source not available (continuous horn). Check
battery connection, completely power down and reboot UPS.

Line-to-neutral reversal in the AC input power supply or a loss of
proper grounding; continuous horn and UPS will not start.

Mains power voltage or frequency is out of tolerance; bypass is
unavailable.

25

Troubleshooting

Under fault conditions, the Fault indicators will be illuminated indefi­nitely while battery charger is operational, or for a maximum of 5 min­utes while battery charger is not operational.

If a problem persists, consult your local dealer, Liebert representative
or contact the Liebert Worldwide Support Group. Please have the UPS
model number and serial number available at the time of your
inquiry.

Table 1 Troubleshooting guide

Problem Cause Solution

Ensure UPS is OFF.

UPS fails to start
when the ON
button is pressed.

UPS is short circuited or
overloaded.

UPS not plugged in.

Disconnect all loads and
ensure nothing is lodged in
output receptacles. Ensure
loads are not defective or
shorted internally.

UPS is operating from
battery mode, make certain
UPS is securely plugged
into the wall receptacle.

Battery indicator
LED is
illuminated.

UPS has reduced
battery time.

UPS input protection fuse
has blown/opened.

Mains voltage out of UPS
input range.

Batteries are not fully
charged.

UPS is overloaded.

Batteries may not be able
to hold a full charge due to
age.

UPS is operating from
battery mode. Save data
and close applications.
Replace UPS input fuse,
then restart UPS.

UPS is operating from
battery mode. Save data
and close applications.
Ensure mains supply
voltage is within
acceptable limits for UPS.

Keep UPS plugged in
continuously at least 24
hours to recharge
batteries.

Check load level display
and reduce the load on the
UPS.

Replace batteries. Contact
your local dealer, Liebert
representative or the
Liebert Worldwide Support
Group for replacement
battery kit.

26

Table 1 Troubleshooting guide (continued)

Problem Cause Solution

Check load level display
Fault and Bypass
indicator LEDs
and all load level
LEDs are
illuminated.

Fault and Bypass
indicator LEDs
and diagnostic
LED A are
illuminated.

UPS overloaded or load
equipment is faulty.

UPS internal fan has a
problem or UPS shutdown
due to temperature
condition. Load is on
bypass power.

and remove non-essential

loads. Recalculate the load

and reduce number of

loads connected to UPS.

Check load equipment for

faults.

Ensure UPS is not

overloaded, ventilation

openings not blocked, or

room ambient temperature

is not excessive. Wait 30

minutes to allow UPS to

cool, then restart UPS. If

UPS does not restart,

contact your local dealer,

Liebert representative or

the Liebert Worldwide

Support Group.

Troubleshooting

Fault and Bypass
indicator LEDs
and diagnostic
LED B are
illuminated.

Fault and Bypass
indicator LEDs
and diagnostic
LED C are
illuminated.

Fault and Bypass
indicator LEDs
and diagnostic
LED D are
illuminated.

Fault and Bypass
indicator LEDs
and diagnostic
LED E are
illuminated.

Fault indicator
LED and
diagnostic LED A
and C are
illuminated.

UPS internal DC bus
overvoltage.

UPS control power supply
fault.

UPS PFC (Power Factor
Correction Circuit) fault.

UPS inverter fault.

UPS failed the battery test.

UPS requires service.

Contact your local dealer,

Liebert representative or

the Liebert Worldwide

Support Group.

UPS requires service.

Contact your local dealer,

Liebert representative or

the Liebert Worldwide

Support Group.

UPS requires service.

Contact your local dealer,

Liebert representative or

the Liebert Worldwide

Support Group.

UPS requires service.

Contact your local dealer,

Liebert Representative or

the Liebert Worldwide

Support Group.

Replace batteries. Contact

your local dealer, Liebert

representative or the

Liebert Worldwide Support

Group.

27

Table 1 Troubleshooting guide (continued)

Problem Cause Solution

Your UPS has received a

signal or command from

the attached computer. If

Fault and Bypass
indicator LEDs
and diagnostic
LED C and E are
illuminated.

AC LED is
flashing.

UPS shutdown due to a
command from the
communications port(s).

UPS detected a line-to­neutral reversal or a loss of
proper grounding;
continuous horn and UPS
will not start. This is active
only when power is first
applied to the input. Once
the UPS is running, the AC
LED will not start flashing,
even if the input wiring is
changed.

this was inadvertent,

ensure the communication

cable used is correct for

your system. For

assistance, contact your

local dealer, Liebert

representative or the

Liebert Worldwide Support

Group.

Contact a qualified

electrician to verify site

wiring.

Troubleshooting

Battery LED is
flashing.

Bypass LED is
flashing.

Battery source is not
available; continuous horn.

Bypass voltage is present,
but is disabled for use
because the voltage or
frequency is outside
acceptable limits.

Check battery connections,

completely power down

and restart UPS.

NOTE: If the battery circuit

opens while the UPS is

running, it will be detected

when the next battery test

is performed.

The AC input powers the

PFC input and serves as

the bypass source. If the

AC is present but the

voltage or frequency

exceeds the acceptable

range for safe operation

with a load, the bypass will

be disabled and this LED

will flash, indicating that the

bypass is unavailable.

28

Table 2 Alarm Conditions

Condition Alarm

Troubleshooting

Battery Mode
(mains failure)

Low Battery

Output Overload
(bypass)

Overtemperature
(bypass)

DC Bus Overvoltage
(bypass)

Control Power Supply
Failure (bypass)

One short beep every 10 seconds;
more than 2 minutes of run time remaining

Two short beeps every 5 seconds;
less than 2 minutes of run time remaining

One short beep every half second

A one-second beep every 4 seconds

A one-second beep every 4 seconds

A one-second beep every 4 seconds

PFC Failure (bypass) A one-second beep every 4 seconds

Inverter Failure A one-second beep every 4 seconds

Battery Test Failure A 2-second beep every minute

29

12.0 SPECIFICATIONS

Specifications

Model Number
Model Rating
DIMENSIONS: mm

Unit W x D x H: mm

Shipping W x D x H: mm

WEIGHT: kg

Unit: kg

Shipping: kg

INPUT AC PARAMETERS

Voltage Range

(typical)

100% - 90% loading

90% -70% loading
70% -30% loading

30% - 0% loading

Frequency

Input Connector

OUTPUT AC PARAMETERS

Output Sockets

Voltage

Frequency

Waveform

Main Mode

Overload

BATTERY PARAMETERS

Type

Qty x V x Rating

Battery Mfg/Part #

Back-up Time

Recharge Time

ENVIRONMENTAL

Operating Temp

Storage Temp

Relative Humidity

Operating Elevation

Storage Elevation

Audible Noise

AGENCY

Safety

RFI/EMI

Surge Immunity

Transportation

GXT2-700RT230 GXT2-1000RT230 GXT2-1500RT230

700VA / 490W 1000VA / 700W 1500VA / 1050W

87 x 547 x 430 87 x 547 x 430 87 x 547 x 430

268 x 692 x 585 268 x 692 x 585 268 x 692 x 585

22.5 22.6 23.2

26.5 26.6 27.2

230 VAC nominal;

variable based on output load
159VAC / 280VAC 159VAC / 280VAC 176 VAC / 280VAC
159VAC / 280VAC 159VAC / 280VAC 159 VAC / 280VAC
139VAC / 280VAC 139VAC / 280VAC 139 VAC / 280VAC
119VAC / 280VAC 119 VAC / 280VAC 119VAC / 280VAC

40 - 70 Hz; Auto Sensing

IEC320-10A

(6) EN 60320/C13

200/208/220/230/240 (user configurable) VAC; ±3%

50 Hz or 60 Hz

Sinewave

200% for 8 cycles;

130% for 10 seconds with transfer to bypass

Valve-regulated, nonspillable, lead acid

4 x 12V x 7.0 or 7.2 AH

China Storage Battery / CSB 1270 F2

See 13.0 - Battery Run Times

5 Hours to 95% capacity after full discharge

into 100% load (Internal Batteries Only)

0°C to +40°C (+32°F to +104°F)

-15°C to +50°C (+5°F to +122°F)
0% to 95%, non-condensing

Up to 3000 m (10,000 ft.) at 40°C (104°F) without derating

15,000 m (50,000 ft.) maximum

<50 dBA, at 1 metre from the rear

<45 dBA, at 1 metre from the front or sides

EN 62040-1, CE compliance mark,

for both Low Voltage and EMC Directives

EN 62040-2, Class B

EN 61000 4-2, 4-3, 4-4, 4-5

ISTA Procedure 1A

30

Specifications

SPECIFICATIONS, CONTINUED

Model Number GXT2-2000RT230 GXT2-3000RT230 / 3KRT230E
Model Rating 2000VA / 1400W 3000VA / 2100W
DIMENSIONS: mm

Unit W x D x H: mm 87 x 547 x 430 87 x 618 x 430
Shipping W x D x H: mm 268 x 692 x 585 268 x 692 x 585

WEIGHT: kg

Unit: kg 24.7 31.9
Shipping: kg 28.7 35.9

INPUT AC PARAMETERS

Voltage Range
(typical)
100% - 90% loading 176VAC / 280VAC 176VAC / 280VAC
90% -70% loading 159VAC / 280VAC 159VAC / 280VAC
70% -30% loading 139VAC / 280VAC 139VAC / 280VAC
30% - 0% loading 119VAC / 280VAC 119VAC / 280VAC
Frequency 40 - 70 Hz; Auto Sensing
Input Connector IEC320-10A IEC320-16A

OUTPUT AC PARAMETERS

Output Sockets (6) IEC320-10A

Voltage 200/208/220/230/240 (user configurable) VAC; ±3%
Frequency 50 Hz or 60 Hz
Waveform Sinewave
Main Mode
Overload

BATTERY PARAMETERS

Type Valve-regulated, nonspillable, lead acid
Qty x V x Rating 4 x 12V x 9.0 AH 6 x 12V x 9.0 AH

Battery Mfg/Part #

Back-up Time See 13.0 - Battery Run Times

Recharge Time

ENVIRONMENTAL

Operating Temp 0°C to +40°C (+32°F to +104°F)
Storage Temp -15°C to +50°C (+5°F to +122°F)
Relative Humidity 0% to 95%, non-condensing
Operating Elevation Up to 3000 m (10,000 ft.) at 40°C (104°F) without derating
Storage Elevation 15,000 m (50,000 ft.) maximum

Audible Noise

AGENCY

Safety

RFI/EMI EN 62040-2, Class B
Surge Immunity EN 61000 4-2, 4-3, 4-4, 4-5
Transportation ISTA Procedure 1A

130% for 10 seconds with transfer to bypass

5 Hours to 95% capacity after full discharge

into 100% load (Internal Batteries Only)

<55 dBA, at 1 metre from the rear

<50 dBA, at 1 metre from the front or sides

EN 62040-1, CE compliance mark,

for both Low Voltage and EMC Directives

230 VAC nominal;

variable based on output load

(6) IEC320-10A,

(1) IEC320-16A

200% for 8 cycles;

Panasonic UP-VW1245P1

Yuasa / REW 45-12

31

Specifications

12.1 Battery Cabinet Specifications

Model Number GXT2-48VBATT GXT2-72VBATT

GXT2-700RT230

Used w/ UPS Model

DIMENSIONS: mm

Unit W x D x H: mm 87 x 547 x 430 87 x 618 x 430

Shipping W x D x H: mm 268 x 692 x 585 268 x 692 x 585

WEIGHT: kg

Unit: kg 28.3 42.5

Shipping: kg 32.3 46.5

BATTERY PARAMETERS

Type Valve-regulated, nonspillable, lead acid

Qty x V x Rating 2 x 4 x 12V x 7.0 or 7.2 AH 2 x 6 x 12V x 9.0 AH

Battery Mfg /
Part #

Back-up Time See 13.0 - Battery Run Times

ENVIRONMENTAL

Operating Temp 0°C to +40°C (+32°F to +104°F)

Storage Temp -15°C to +50°C (+5°F to +122°F)

Relative Humidity 0% to 95%, non-condensing

Operating Elevation Up to 3000 m (10,000 ft.) at 40°C (104°F) without derating

Storage Elevation 15,000 m (50,000 ft.) maximum

AGENCY

Safety

RFI/EMI EN 62040-2, Class B

Transportation ISTA Procedure 1A

GXT2-1000RT230
GXT2-1500RT230
GXT2-2000RT230

China Storage Battery /

CSB 1270 F2

EN 62040-1, CE compliance mark,

for both Low Voltage and EMC Directives

GXT2-3000RT230

Panasonic / UP-VW1234P1

Yuasa / REW 45-12

32

Battery Run Times

13.0 BATTERY RUN TIMES

Load% 700VA 1000VA 1500VA 2000VA 3000VA

10% 248 191 144 56 91
20% 115 87 53 33 46
30% 79 48 38 26 30

Internal
Battery
(minutes)

Internal Battery
+ 1 External
Battery Cabinet
(minutes)

Internal Battery
+ 2 External
Battery
Cabinets
(minutes)

Internal Battery
+ 3 External
Battery
Cabinets
(minutes)

Internal Battery
+ 4 External
Battery
Cabinets
(minutes)

Note: Approximate discharge times are in minutes and at 25°C (77°F) with a 100% resistive load.

40% 58 34 28 19 21
50% 44 25 20 14 16
60% 35 19 15 12 11
70% 29 16 12 10 9
80% 24 13 10 8 8
90% 20 12 8 7 7

100% 17 11 7 6 5

10% 992 764 576 328 364
20% 460 348 212 159 184
30% 316 192 152 88 120
40% 232 136 112 67 84
50% 176 100 80 52 64
60% 140 76 60 36 44
70% 116 64 48 30 36
80% 96 52 40 24 32
90% 80 48 32 21 28

100% 68 44 28 18 20

10% 1984 1528 1152 392 728
20% 920 696 424 231 368
30% 632 384 304 182 240
40% 464 272 224 133 168
50% 352 200 160 98 128
60% 280 152 120 84 88
70% 232 128 96 70 72
80% 192 104 80 56 64
90% 160 96 64 49 56

100% 136 88 56 42 40

10% 2976 2292 1728 560 1092
20% 1380 1044 636 330 552
30% 948 576 456 260 360
40% 696 408 336 190 252
50% 528 300 240 140 192
60% 420 228 180 120 132
70% 348 192 144 100 108
80% 288 156 120 80 96
90% 240 144 96 70 84

100% 204 132 84 60 60

10% 3968 3056 2304 840 1456
20% 1840 1392 848 495 736
30% 1264 768 608 390 480
40% 928 544 448 285 336
50% 704 400 320 210 256
60% 560 304 240 180 176
70% 464 256 192 150 144
80% 384 208 160 120 128
90% 320 192 128 105 112

100% 272 176 112 90 80

33

13.1 Product Warranty Registration

To register for warranty protection:

•Visit the Quick Links section of our Web site at:

Battery Run Times

http://www.liebert.com

• Click on Product Warranty Registration and fill in the form.

If you have any questions, please contact us at:

US: 800-222-5877
Outside the US: 614-841-6755

[e-mail]

34

Ensuring The High Availability
0f Mission-Critical Data And Applications.

Technical Support / Service

Web Site

www.liebert.com

Monitoring

800-222-5877
[e-mail]
Outside the US: 614-841-6755

Single-Phase UPS

800-222-5877
[e-mail]
Outside the US: 614-841-6755

Three-Phase UPS

800-543-2378
[e-mail]

Environmental Systems

800-543-2778
Outside the United States
614-888-0246

While every precaution has been taken to ensure the accuracy and completeness of this literature, Liebert Corporation assumes
no responsibility and disclaims all liability for damages resulting from use of this information or for any errors or omissions.
© 2007 Liebert Corporation
All rights reserved throughout the world.
Specifications subject to change without notice.
® Liebert is the registered trademark of Liebert Corporation. All names referred to are trademarks or
registered trademarks of their respective owners.

35028 Piove Di Sacco (PD) Italy

7/F, Dah Sing Financial Centre

108 Gloucester Road, Wanchai

1050 Dearborn Drive

Columbus, OH 43229

Via Leonardo Da Vinci 8

Zona Industriale Tognana

Fax: [phone]

Locations

United States

P.O. Box 29186

Europe

[phone]

Asia

Hong Kong

852 2572220

Fax: [phone]

SLI-23150_REV07_01-08

Emerson Network Power.

The global leader in enabling Business-Critical Continuity™.

AC Power Systems

EmersonNetworkPower.com

Outside Plant

Connectivity

DC Power Systems

Embedded Computing

Embedded Power

Integrated Cabinet Solutions

Business-Critical Continuity, Emerson Network Power and the Emerson Network Power logo are
trademarks and service marks of Emerson Electric Co.

©2007 Emerson Electric Co.

Power Switching & Control

Precision Cooling

Services

Site Monitoring

Surge Protection