Dyson Airblade TAP AB11, Airblade TAP AB10, Airblade TAP AB09 Pre-installation Information
200mm maximum
385mm minimum
200mm maximum
350mm minimum
385mm minimum
300mm minimum
100mm minimum
200mm maximum
PRE-INSTALLATION INFORMATION
distributed by
RESTROOM DIRECT 704 .937. 2673 www.RestroomDirect.com
Sink specification guidelines
The Dyson Airblade Tap hand dryer is compatible with
most sink types.
Do not use plugs within the plug holes in sinks.
Due to high velocity air and water being in close proximity,
there is a chance of some water dispersion outside
the sink dimensions.
Sinks with highly polished surfaces should be avoided
e.g. reflective chrome.
Porcelain or brushed metal are ideal.
Fi g .1
1325⁄32" minimum
350mm minimum
" minimum
16
⁄
13
11
300mm minimum
Tap mounting
The tap stem (measured from the outside diameter) should
19
be mounted
⁄32" – 19⁄16" from the outside edge of the sink.
When multiple taps are installed side-by-side, tap centers
should be a minimum of 22
27
⁄64" from tap center to a side wall. This allows sufficient
11
53
⁄64" apart and a minimum of
space for mounting the motor bucket horizontally as well as
enough space for users at the sink (shoulder to shoulder).
Do not place the downward facing water sensor of the tap over
a reflective surface, such as the drainage hole. (Fig.4)
Fig.2
" maximum
8
⁄
7
7
200mm maximum
Fig.3 Fig.4
Sink dimensions (All internal measurements unless otherwise stated)
Fig.1 Width of sink minimum: 13
Fig.2 Maximum depth of sink for Long Neck Tap (AB10) only: 7
(External measurement of vessel/pedestal sink).
155⁄32" minimum
" minimum
16
⁄
15
3
100mm minimum
25
⁄32", Front to back of sink minimum: 1113⁄16"
7
⁄8"
Fig.3 Minimum distance from tap center to top of sink (AB11 only) 315⁄16".
Front edge of sink (all t ypes – pedestal, recessed, slab) to wall minimum 15
Internal depth of sink minimum (for all taps): 315⁄16"
For further information please contact Dyson.
888-397-6622
airbladeinfo@dyson.com
www.dysonairblade.com
5
⁄32".
Locating the soap dispenser
distributed by
RESTROOM DIRECT 704 .937. 2673 www.RestroomDirect.com
Mounting the motor bucket (AB09/AB10)
The infrared sensing zone for air activation extends along each
tap branch. Therefore, it is the user’s hand route to the soap
dispenser that is most important to prevent nuisance activation.
23
The soap dispenser should be located at least 2
⁄64" outside the
width of the tap. This is so the user can reach around the side of
the branch.
23
The soap dispenser should be located at least 2
⁄64" above
the branches so that the sensors are not activated.
It is also important to note that the user may reach diagonally
across for the soap and this path must not go through the
sensing zone.
"
64
Front on view showing
soap dispenser
clear zone.
⁄
23
2
223⁄64"223⁄64"
The motor bucket cannot be mounted upside down.
The motor bucket cannot be installed above the sink.
15
⁄16" minimum clearance from bottom of motor bucket
3
to floor/wall.
Only the following is advised.
L N
L N
L N
315⁄16"
"
16
⁄
15
3
Over head view
showing soap
dispenser clear zone.
223⁄64" 223⁄64"
"
64
⁄
23
2
For further information please contact Dyson.
888-397-6622
airbladeinfo@dyson.com
www.dysonairblade.com
" minimum
16
⁄
15
3
Mounting the motor bucket (AB11)
Metal enclosure assembly
This Dyson product is designed so the motor unit is located
behind the stud wall. The vertical wall studs must be constructed
so as to allow the metal enclosure to be fitted between them.
One of the horizontal wall studs must be fitted a) so it holds the
main weight of the metal duct and the unit, and b) so it is in the
correct position for the tap stem.
Loading...