Dymo RHINO 6000 User Manual

www.dymo.com

User Guide

Backlight

Power

Tap e Ex it

LCD d ispla y

Cut/Feed

Hot Keys

Barcode

Symbol

Size/CAPS

Save/Insert

Recall/Remove

USB connector

Space bar

Print/# of copies

Library

Escape

Clear

Navigation keys

OK

Serialization

Settings

Backspace

Enter

Shift

Power connector

Figure 1 RHINO 6000 LabelPrinter

Contents

About Your New Printer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1

Getting Started . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1

Connecting the Power . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1

Connecting the Power Adapter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1

Inserting the Battery Pack. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1

Recharging the Battery Pack. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

Inserting and Removing the Tape Cassette . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

Setting the Tape Width . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

Selecting a Language . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

Selecting Units of Measure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

Getting to Know Your Printer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

Power . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

LCD Display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

Using the Backlight . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

Adjusting the Display Contrast . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

Hiding the Caption Bar. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

CAPS Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

Shift Key . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

Escape Key . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

Navigation Keys . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

Backspace Key . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

Clear Key . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

Cutter Button . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

Hot Keys . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

Working with Label Files . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

Creating a Label File . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

Adding Labels to a Label File . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

Removing Labels from a File . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

Printing a Label File . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

Formatting a Label . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

Changing the Text Size . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

Changing the Text Style . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

Creating Multi-Line Labels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

Using International Characters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

Creating Industrial Labels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

Creating Wire Wrap Labels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

Creating Vertical Wrap Labels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

Creating Horizontal Wrap Labels. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

Creating Self-Laminating Labels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

Creating Flag Labels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

Creating Fixed Length Labels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

Creating Patch Panel Labels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

Creating Terminal Block Labels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

Creating Module Labels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

Using Fuse Multipliers. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

Printing Empty Modules. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

Creating Vertical Labels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

Changing the Label Type . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

Changing the Label Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10

Printing Vertical Lines between Cells . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

Using Barcodes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

Adding a Barcode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10

Editing a Barcode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10

Deleting a Barcode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10

Hiding Barcode Text . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

Adding Symbols . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

Inserting Symbols . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11

Inserting User Symbols . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11

Using the Text Library . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11

Inserting Library Text . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

Adding My Library Text . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12

Deleting My Library Text . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

Adding Graphics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

Creating a Series of Labels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

Using Simple Serialization . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12

Using Simultaneous Serialization . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

Using Advanced Serialization . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

Printing Options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

Printing Multiple Copies . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

Collating Multiple Copies . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

Pausing between Labels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

Advancing the Label Tape . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

Adjusting Print Contrast . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

Using Printer Memory . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

Saving a Label File . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

Recalling a Label File from Memory . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

Deleting a Label File from Memory . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

Cleaning Your Printer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

Using RHINO Connect Software . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

Connecting to your Computer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

Symbols . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

Library Text . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

Contacting Customer Support . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

About Your New Printer

With your new RHINO label printer, you can create a
wide variety of high-quality, self-adhesive labels. You
can choose to print your labels in many different sizes,
and styles. The printer uses RHINO Industrial label tape
cassettes in widths of 6 mm, 9 mm, 12 mm, 19 mm, or
24 mm. RHINO tape cassettes are also available in a
wide range of materials, such as flexible nylon,
permanent polyester, vinyl, non-adhesive tag, and
heat shrink tubes.

Visi t www.dymo.com for information on the full line
of labels and accessories for your printer.

Warranty Registration

Please complete the warranty registration card and
return it to the appropriate customer service address
within seven days. Visit www.dymo.com for details.

Getting Started

Follow the instructions in this section to start using
your printer for the first time.

Connecting the Power

The printer can operate on battery or AC power. A
power adapter and a rechargeable battery pack is
included with your printer.

The printer can operate with six AA alkaline
batteries for power; however, alkaline batteries should
only be used as temporary backup power.

To save power, the printer will automatically turn off
after five minutes of inactivity.

Connecting the Power Adapter

The printer uses a 110V-240V power adapter.
Connecting the power adapter with the battery pack
inserted recharges the battery pack.

To connect the power adapter

1. Plug the power adapter into the power connector
on the bottom of the printer. See Figure 2.

Figure 2

2. Plug the other end of the power adapter into a
power outlet.

Inserting the Battery Pack

The printer uses the rechargeable, Lithium-ion battery
pack when not connected to the power adapter. As
temporary backup power, the printer can operate
using six AA alkaline batteries.

To insert the battery pack

1. Press the thumb latch on the back of the printer to
remove battery compartment cover. See Figure 3.

Press thumb
latch to open

Figure 3

2. Insert the battery pack into the battery
compartment. See Figure 3.

3. Replace the battery compartment cover.

Remove the batteries if the printer will not be

used for a long period of time.

1

Recharging the Battery Pack

The battery pack automatically recharges while the
printer is connected to a power source through the
power adapter. Charging the battery pack for the first
time will take approximately eight hours; recharging
the battery pack will take approximately two hours.

Inserting and Removing the Tape Cassette

Your printer comes with a starter tape cassette. Visit
www.dymo.com for information about purchasing
additional tape cassettes.

To insert the tape cassette

1. Gently lift the tape cassette door on the back of the
printer.

2. Make sure the tape and ribbon are taut across the
mouth of the cassette and that the tape passes
between the guides. If necessary, turn the ribbon
rewind spool clockwise to tighten the ribbon.

3. Insert the cassette with the tape and ribbon
positioned between the guideposts.

Lift

Guide posts

Ribbon rewind
spool

5. Close the tape cassette door.

To remove the tape cassette

1. Gently lift the tape cassette door on the back of the
printer.

2. Press the cassette eject button. The tape cassette is
lifted from the printer.

3. Gently remove the tape cassette.

4. Insert a new tape cassette as described above.

5. Reset the tape width as described in Setting the

Tape Width.

Setting the Tape Width

Each time you insert a tape cassette into the printer,
you are prompted to set the tape width so the printer
knows what size label tape you are currently using.
Some of the features you use to design labels are
dependent on the width of the tape.
However, to create a label for a tape width different
than what is currently in the printer, you can set the
tape width from the Settings menu.

To set the tape width

1. Press SETTINGS. The Settings menu appears on the
display.

2. Select Tape Width.

3. Select the width of the label tape currently inserted
in the printer.

4. Press OK and then select Done (ESC).

Eject Button

Figure 4

4. Press gently on the cassette until the cassette
moves into place. The insertion mechanism will
guide the cassette into place.

2

Selecting a Language

Several language-related features on the printer are
determined by the language setting, such as special
characters, menu text, and so on. By default the
language is set to English.

To s elect a language

1. Press SETTINGS and select Language.

2. Select the language.

3. Press OK and then select Done (ESC).

Selecting Units of Measure

You can choose to work in inches or millimeters.

To select the units of measure

1. Press SETTINGS and select Units.

2. Select Inch or mm.

3. Press OK and then select Done (ESC).

Getting to Know Your Printer

Become familiar with the location of the feature and
function keys on your printer. See Figure 1 on the
inside front cover. The following sections describe each
feature in detail.

Power

The button turns the power on and off. If no keys
are pressed after five minutes, the power is turned off
automatically.

When the printer is turned off, the current label file
and its settings are remembered for the next time the
printer is turned on. If the battery pack and power
adapter are disconnected at the same time, some of
the settings are remembered; however, the current
label file is lost and you will need to reset the tape
width when you reconnect the power and turn on the
printer.

LCD Display

The printer’s LCD display includes a caption bar across
the top, showing the current label type, and feature
indicators on the right side, showing which features
are currently selected. See Figure 5.

Caption bar

Figure 5

Feature
indicators

Battery level
indicator

When the text you have entered will not fit on the
label as currently defined, the portion of the text that
will not fit is shaded. If you attempt to print the label
containing text that will not fit, the excess text will not
be printed.

Using the Backlight

In low light conditions, you can turn on the backlight
to make it easier to see the display. To save power, the
back light will turn off automatically after 15 seconds
of inactivity. Pressing any key will turn the backlight
back on again. The backlight key acts as a toggle to
turn the light on and off.

To toggle backlighting on and off

♦ Press .

Adjusting the Display Contrast

In addition to backlighting, you can adjust the display
contrast to help in different lighting conditions.

To adjust the display contrast

1. Press SETTINGS.

2. Select LCD contrast and press OK.

3. Use the arrow keys to select a value between
0 (lighter) and 8 (darker). The contrast changes as
you select the different settings.

4. Press OK, and then select Done (ESC).

3

Hiding the Caption Bar

The Caption bar at the top of the display shows the
current label type and for some label types, additional
information about the label, such as size or barcode
type. The Caption bar can be hidden to allow more
lin es of t he labe l to be shown in the displa y. Th is is ve ry
useful for multi-line labels.

To hide the Caption bar

1. Press SETTINGS.

2. Select Caption bar and press OK.

3. Select Hide, press OK, and then select Done (ESC).

CAPS Mode

The CAPS key toggles capitalization on and off. When
CAPS mode is turned on, the CAPS indicator is shown
on the display and all letters that you enter will be
capitalized. The factory default setting is CAPS mode
on. When CAPS mode is off, all letters entered appear
in lower case.

To toggle CAPS on and off

♦ Press CAPS (SHIFT + SIZE).

Shift Key

The SHIFT keys are used to select the function or
symbol printed above a key. For example, when you
press the 9 key, the number 9 appears in the display;
however, if you press SHIFT and then 9, an asterisk (*)
appears in the display. Pressing one of the Shift keys
toggles the function on and off, so you do not need to
hold down both keys together.

Escape Key

The ESC key returns you to the previous menu from
within any menu without making a selection.

Navigation Keys

The navigation keys operate as follows:

Key Function

Moves one character to the left in the display

,

Returns to the previous menu (can also use

SHIFT

Moves one label to the left in the display

,

Moves one character to the right in the display

=

Moves to the next menu level (can also use

SHIFT

Moves one label to the right in the display

=

Moves up in a list of items

;

Moves down in a list of items

:

Selects a menu item

OK

ESC)

OK)

Backspace Key

The key removes the character to the left of the
cursor.

Clear Key

The CLR key clears all current text settings and format,
returning the display to the General label type.

Cutter Button

The Cutter button cuts the label tape. When printing
multiple labels, the printer pauses after printing each
label so that you can cut the label. You can turn this
feature off, so that multiple labels will print
continuously. See Pausing between Labels on
page 14.

Hot Keys

A number of hot keys are available for creating specific
types of labels, adding barcodes, inserting symbols,
and using the text from the library. These hot keys are
described in detail later in this user guide.

4

Working with Label Files

The printer creates and stores labels as label files. A
label file can contain one or more labels. When you
create a new label, you also create a new label file. You
can then insert additional labels, remove labels, and
store the group of labels as a label file in memory.

Creating a Label File

The printer remembers the last label that you were
working on when the power was turned off. You need
to clear that label text and formatting before you
create a new label.

To create a new label file

1. If necessary, press CLR to clear the previous label
and formatting from the display.

2. Type some text using the keypad.

3. Format the text using Text Size or Text Style. See
Formatting a Label on page 5.

4. Save the label to memory. See Saving a Label File
on page 14.

Adding Labels to a Label File

You can add additional labels to an existing label file.

To add a label to a file

1. Press INSERT (SHIFT + SAVE).

2. Select To th e ri ght to add a label to the right of the
cursor position or To the l eft to add a label to the
left of the cursor position.

3. Press OK. A new blank label is inserted in the
display to the left or right of the current label.

You can move from label to label using the arrow keys.

Removing Labels from a File

You can remove one or more labels from a label file.

To remove a la bel

1. Press REMOVE (SHIFT + RECALL).

2. Select one of the following:

• All to remove all of the labels in the file.

• Current to remove the label at the current
cursor position.

• Range and then select the range of labels to
remove.

3. Press OK. The selected labels are removed from the
display.

Printing a Label File

When you print a label file, you choose whether to
print all of the labels, the current label, or a range of
labels in the file.

To print labels

1. Press PRINT. If your label file contains more than
one label, a print menu is displayed.

2. Select one of the following:

• All to print all of the labels in the file.

• Current to print the label at the current cursor

position.

• Range and then select the range of labels to

print.

3. Press OK. The labels selected are printed.

4. Press CUT and remove the labels.

Formatting a Label

You can choose from a number of formatting options
to enhance the appearance of your labels.

Changing the Text Size

You can print the text on your label in eight sizes:
extra-extra-small, extra-small, small, medium, large,
extra-large, extra-extra-large and BIG (all capital
letters). The text size selected applies to all the text on
all the labels in a label file.

5

You can also select Auto as the text size. When Auto is
selected, the best text size is automatically determined
for the height and width of the label you are creating.
BIG font is not used when Auto text size is selected.

The text size available for you to use depends on
the width set for the label tape and the type of label
you are creating.

To set the font size

♦ Press SIZE. Each time you press SIZE, the next

available font size is highlighted on the Size feature

indicator on the display.
You can also select the font size from the Settings
menu.

Changing the Text Style

You can print the text on your label in several styles:
bold, italic, underlined, and boxed. And, you can
choose normal width or narrow width. The text style
applies to all the text on all the labels in the label file,
including most symbols. Text style is not applied to
user defined symbols.

To set the text style

1. Press SETTINGS.

2. Select Tex t style and press OK.

3. Use the arrow keys to select a style.

4. Press OK and then select Done (ESC).

Creating Multi-Line Labels

You can create multi-line labels depending upon the
width of the label tape, as follows:

Tape

Width

# Lines 13355

6 mm 9 mm 12 mm 19 mm 24 mm

The display shows two lines of text with the Caption
bar displayed; or three lines with the caption bar
hidden. Use the arrow keys to scroll through multiple
lines. See Hiding the Caption Bar on page 4.

To create a multi-line label

1. Type the text for the first line, and press ENTER.

2. Type the text for the next line.

3. Repeat these steps for each additional line.

Using International Characters

The printer supports the extended Latin character set
using RACE technology. Similar to using a mobile
phone keypad, holding down a letter key will scroll
through variations of that letter.
For example, if you hold down the letter a, you will see
a à á â ã ä å and so on through all the variations
available. The order in which the character variations
appear depends on the language you selected to use.

Creating Industrial Labels

You can quickly create labels for special industrial
applications, such as cable wraps, flags, patch panels,
terminal blocks, or modules. You can create fixed
length labels or self-laminated labels.

Hot keys are available for each of the label types
available. The current label type is displayed in the
Caption bar. By default, the label type is General with
no special formatting, text centered, and the length
automatically determined by the amount of text.

The hot keys toggle the label type on and off. For
example, if you choose Flag and later want a General
label, just press the Flag key a second time to remove
the Flag settings and return to General label type.

6

Creating Wire Wrap Labels

You can create several types of labels that wrap around

a cable or wire: vertical wire wrap, horizontal wire

wrap, self-laminating, and flag labels.

Creating Vertical Wrap Labels

A Vertical Wrap label is placed

around the width of a wire or

cable. You can enter up to five

lines of text and the text is

repeated as many times as

possible depending on the size of the text and the

length of the label.

To create a vertical wrap label

1. Press V.W RAP.

2. Enter the diameter of the cable and press OK.

3. Select Done (ESC) to create the label.

To create multiple labels quickly, see Creating a

Series of Labels on page 12.

Creating Horizontal Wrap Labels

A Horizontal Wrap label is

placed horizontally along the

length of the wire or cable. The

label text is repeated as many

times as possible depending on the size of the text and

the width of the tape.

To create a horizontal wrap label

1. Press H.WRAP (SHIFT + V.W RAP) .

2. Enter the label length and press OK. Select AUTO to
have the length automatically set to fit the text.

3. Select Done (ESC) to create the label.

To create multiple labels quickly, see Creating a

Series of Labels on page 12.

Creating Self-Laminating Labels

The Self-Laminating label is
designed to be used with RHINO
Self-Laminating Labels (part
number 1734821). The text of the
label is printed on the top portion
of the label so the clear, bottom
half of the label can wrap around and cover the text.
Self-Laminating tape is 24 mm wide; however, you can
only enter two lines of text and are limited to using
extra-extra-small, extra-small, and small font sizes.

To print a self-laminating label

1. Press SELF-LAM (SHIFT + FLAG).

2. Enter the label length or select AUTO to have the
label length automatically set to fit the text.

3. Press OK to create the label.

To create multiple labels quickly, see Creating a

Series of Labels on page 12.

Creating Flag Labels

Flag labels wrap around a wire or
cable leaving the text part of the
label extending out from the
cable. The text on flag labels is
automatically printed on both
ends of the label leaving a blank
space in the middle that wraps around the cable.
When the label is applied to the cable, both ends of
the label are applied back to back leaving a tail or flag.
The result is a label that can be read from both sides.

To print a flag label

1. Press FLAG.

2. Enter the length for the flag portion of the label.
Select AUTO to have the length automatically set to
fit the text. The total length of the label is calculated
by doubling the flag length and adding 34 mm to
wrap around the cable.

7

3. Press OK to create the label.

4. Enter the text for the label and press PRINT.
To create multiple labels quickly, see Creating a

Series of Labels on page 12.

Creating Fixed Length Labels

Normally, the length of the label is determined by the
length of the text entered. However, you may wish to
make a label for a specific purpose that is a fixed
length regardless of the length of the text.
The factory default fixed length is 25 mm. Any change
you make to the fixed length setting remains in effect
until you change it.

To set the label length

1. Press FIXED.

2. Enter the length of the label and press OK.
Any text that does not fit within the fixed length
appears shaded in the display and will be truncated
when the label is printed.

Creating Patch Panel Labels

Patch panel mode allows you to
label a row of ports on a patch
panel. You select the distance
between ports, enter the desired
text, and print. The result is a long
label with multiple, evenly spaced
text for each port.

To create a patch panel label

1. Press PPANEL.

2. Select Port distance.

3. Enter the distance between each port and press OK.
The factory default is 15 mm.

4. Select # of ports.

5. Enter the number of ports and press OK.

6. Select Done (ESC) to create the label.

Each port is separated by a solid black line on the
display.

7. Enter the text for each port in the label. Use the left
or right arrow key to move from port to port.

To create data for the ports automatically, see
Creating a Series of Labels on page 12.

To print vertical lines between the ports, see Printing

Vertical Lines between Cells on page 10.

Creating Terminal Block Labels

Terminal block labels are very
similar to patch panel labels;
however, the text is printed
vertically for each block.

To create a terminal block
label

1. Press TBLOCK.

2. Select # of blocks and press OK.

3. Enter the number of blocks and press OK.

4. Select Block size and press OK.

5. Enter the width of each block and press OK. The
factory default is 17.5 mm.

6. Select Done (ESC) to create the label.

7. Enter the text for each terminal.
Use SHIFT + , or = to move among terminals.

To create data for the terminal blocks automatically,
see Creating a Series of Labels on page 12.

Creating Module Labels

The Module label type allows you
to label a row of fuses. You set the
width of a fuse and the number of
fuses, enter the desired text for
each fuse, and print. The result is a
long label with multiple, evenly
spaced text for each port. You can use fuse multipliers
to adjust the width of individual modules as necessary.

8

To create a module label

1. Press MODULE.

2. Select Fuse length and press OK.

3. Enter the fuse length and press OK. Select the
length that applies to the smallest size fuse in the
module. You can then use fuse multipliers to
increase the size of any individual modules that are
larger. See step 6. The factory default fuse length is

17.5 mm.

4. Select # of modules and press OK.

5. Enter the number of modules for this label and
press OK.

6. Adjust the size of individual modules using fuse
multipliers. See Using Fuse Multipliers.

7. Select Done (ESC) to create the label.

8. Enter the text for each module. Use the left or right
arrow key to move from module to module.

To create the data for the modules automatically, see

Creating a Series of Labels on page 12.

Using Fuse Multipliers

Fuse multipliers allow you to adjust the size of
individual fuse modules within a module type label.

To adjust the size of an individual module

1. Create a module label as described in Creating
Module Labels.

2. Press SETTINGS.

3. Select Current label config. and press OK.

4. Select Multipliers and press OK.

5. Use the arrow keys to select the module number to
adjust and press =.

6. Select the multiplier for that module.

7. Press OK and then Done (ESC) to return to the
label.

Printing Empty Modules

You can choose to print empty modules at the end of
Module labels. By default, printing empty modules is
turned off.

To print empty modules

1. Press SETTINGS.

2. Select Print empty modules and press OK.

3. Select On and press OK.

4. Select Done (ESC) to return to the label.
Any empty modules at the end of a module label will
now be printed.

Creating Vertical Labels

You can choose to print labels with
the text running vertically. Labels
with multiple lines of text will
print as multiple columns of text.

To print a vertical label

1. Enter the text for your label.

2. Press VERTICAL.

3. Enter a length for the label. Select AUTO to have the
length of the label automatically set to fit the text.

4. Press OK to create the label.

Changing the Label Type

Once you create a label using one label type, you can
easily change the label type without losing your data.
When you change from a multi-cell label, such as a
patch panel, to a single cell label, such as General or
Flag, each cell becomes a new label. All blank cells are
deleted.
If the data from one label type will not fit in the new
label type, the text that will not fit is shaded in the
display.

To change the label type

1. Press the hot key for the new label type.

9

2. Make any necessary adjustments to the settings for
the label type.

Changing the Label Settings

Once you create a specific label, you can change the
settings without starting all over again.

To change the label settings

1. Press SETTINGS.

2. Select Current label config. and press OK.
The settings for the particular label type are
displayed.

3. Make the necessary changes.

4. Press OK and then select Done (ESC).

Printing Vertical Lines between Cells

For multiple cell labels, such as Patch Panel, Terminal
Block, and Module, you can choose to print a vertical
line between each of the cells.

To print vertical lines between cells

1. Press SETTINGS.

2. Select Vert. lines and press OK.

3. Select On.

4. Press OK and then select Done (ESC).

A vertical mark is printed between each cell.

Using Barcodes

The printer can generate the following types of
barcodes.

Code 39 EAN 8
Code 128 Auto EAN13
UPC A UPC E

You can only print a barcode on 19 mm and 24 mm
wide label tape. You can choose to print the human­readable text or not, and you can serialize barcodes.

The barcode prints horizontally along the label with
the text in small print underneath the barcode. You
can optionally add text before and after the barcode.

Adding a Barcode

The barcode text appears on the label in the display
just like any other text. However, if the cursor is
positioned within the barcode text, Barcode and the
type of barcode are displayed in the Caption bar.

To add a barcode

1. Press BARCODE.

2. Use the arrow keys to select the barcode type, and
press OK.

3. Enter the text for the barcode within the barcode
and press OK.

Editing a Barcode

You edit an existing barcode or delete a barcode in the
same manner.

To e dit a ba rco de

1. Move the cursor anywhere within the barcode text.

2. Press BARCODE or type a character. A message
appears asking if you would like to edit the barcode.

3. Press OK. The text of the existing barcode appears.

4. Edit the barcode text and press OK.

Deleting a Barcode

A barcode is entered on the label as one character.

To d ele te a bar code

1. Place the cursor at the end of the barcode on the
display.

2. Press .

Hiding Barcode Text

You can choose to hide the human-readable text for
the barcode.

10

To hide barcode text

1. Press SETTINGS.

2. Select Barcode HR and press OK.

3. Select Off.

4. Press OK and then select Done (ESC).

Adding Symbols

Your printer includes a set of default symbols to use on
your labels. The symbols are separated into several
categories:

Electrical Brackets
Voice/Data Arrows
Audio/Video Numbers
Warning Home Electrical
Punctu ation Cur rency

A complete list of the default symbols can be found
beginning on page 16.

Some of the more popular symbols can be accessed
from the number keys using SHIFT plus the number.
For example, pressing SHIFT + 1 inserts an open
bracket ([).
If you transfer a custom set of symbols from the RHINO
Connect™ Software to the printer, an additional set of
User symbols becomes available. See Using RHINO

Connect Software on page 15 for more information.

Inserting Symbols

Symbols added to a label can be formatted or deleted
just like any other character you enter.

To insert a symbol

1. Press SYMBOL.

2. Select Default, if necessary.

3. Select a category of symbols.

4. Use the arrow keys to find the symbol you want.

5. Press OK to insert the symbol on the label.

Inserting User Symbols

Custom symbols downloaded from RHINO Connect
Software are stored as User symbols. See Using
RHINO Connect Software on page 15 for more
information.

You insert User symbols in the same manner as pre­defined symbols; however, User symbols cannot be
formatted.

To insert a User symbol

1. Press SYMBOL.

2. Select User.

3. Use the arrow keys to find the symbol you want.

4. Press OK to insert the symbol on the label.

Using the Text Library

Your printer includes a pre-defined text library. The
library is separated into several categories:

Location Voice/Data
Audio Security
Vide o

An additional category, called My Library, is available
for you to add custom text to use on your labels.

My Library text is not included when you select

All from the Library menu.
A complete list of pre-defined text strings can be

found beginning on page 17.

Inserting Library Text

Library text added to a label can be edited, formatted,
or deleted just like text you enter from the keypad.

To add text to a label

1. Press LIBRARY.

2. Select one of the categories.

11

3. Press the first letter of the text string you wish to
use. The cursor jumps to the first text string that
begins with that letter.

4. Press OK to insert the text on the label.

Adding My Library Text

You can download custom text from RHINO Connect
Software or you can add custom text to the library
directly from the printer. See Using RHINO Connect

Software on page 15 for more information.
To a dd c ust om t ext

1. Press LIBRARY.

2. Use the arrow keys to select My Library.

3. Select Add new text and press OK.

4. Enter the text and press OK.
The text is added to My Library.

Deleting My Library Text

You can delete custom text from My Library.

To delete My Library text

1. Press LIBRARY.

2. Use the arrow keys to select My Library.

3. Select the text to delete.

4. Press . A confirmation message appears.

5. Press OK to delete the text.

Adding Graphics

When labels are transferred to the printer from RHINO
Connect Software, any images are stored separately in
the printer as graphic files. You can apply these graphic
files to most labels. When a graphic cannot be used
with a certain label, a warning appears on the display.

See RHINO Connect Software Online Help for more
information about placing images on a label.

To add a graphic

1. Press SETTINGS.

2. Select Choose graphic and press OK.

3. Select the graphic file you want to use and press OK.
The graphic does not appear in the display, but will
print on the label.

Creating a Series of Labels

You can automatically generate labels by creating a
series. You create a starting pattern, and then set the
increment and count for the series.

You can serialize any number or letter by selecting the
position to be incremented, such as the number 2 in
123 or the letter B in ABC. For example, when the 2 is
selected in 123 and the increment #=3, the resulting
labels would print as 123, 153, and 183.
Letters can be incremented from A to Z and a to z, and
numbers from 1 to 9. When the letter Z or the number
9 is reached during serialization, a letter or number is
added to increase the increment. For example, Az
increments to Aaa, AZ increments to BA, and A9
increments to A10.

Three methods of serialization are available: simple,
simultaneous, and advanced.

Using Simple Serialization

Simple serialization creates a series of labels by
incrementing one alphanumeric character in the
pattern. For example, 101, 102, 103, 104, and so on.

To use simple serialization

1. Enter the text for your label.

2. Press SERIAL. A box appears around the first
character in the label.

3. Use the arrow keys to move the cursor to the
position you wish to increment and press OK.

4. Select the amount you want to increment each
label and press OK. You choose to increment in
steps up to 10.

5. Select the number of labels you want to create and
press OK. You can choose to create up to 99 labels.

12

A new label is added in the display for each label in the
series.

To print multiple copies of the same serialized
label, press # COPIES (SHIFT + PRINT) and enter the
number of copies of each label to print. See Printing

Multiple Copies on page 13.

Using Simultaneous Serialization

Simultaneous serialization creates a series of labels by
incrementing two different alphanumeric characters
at the same time. For example, A-101, B-102, C-103,
and so on.

To use simultaneous serialization

1. Enter the text for your label.

2. Press ADV.SER. (SHIFT + SERIAL).

3. Select Simultaneous and press OK. A box appears

around the character where the cursor was
positioned.

4. Select the first character position you want to

increment and press OK.

5. Select the second character position you want to

increment and press OK.

6. Select the amount you want to increment these

characters on each label and press OK. You can
choose to increment in steps up to 10.

7. Select the number of times to increment these

characters and press OK.
A new label is added in the display for each label in the
series.

Using Advanced Serialization

Advanced serialization creates a series of labels by
allowing you to select two sequences in the pattern
and increment them consecutively.

For example, A-101, A-102, A-103, B-101, B-102, B­103, C-101, C-102, C-103, and so on.

To use advanced serialization

1. Enter the text for your label.

2. Press ADV.SER. (SHIFT + SERIAL).

3. Select Advanced and press OK. A box appears
around the character where the cursor was
positioned.

4. Select the first character position you want to
increment and press OK.

5. Select the amount you want to increment this
character position and press OK. You can choose to
increment in steps up to 10.

6. Select the number of times to increment this
character position and press OK.

7. Repeat Steps 4 through 6 for the second character
position you want to increment.

A new label is added in the display for each label in the
series.

Printing Options

You can choose to print multiple copies of the same
label, collate the copies, pause to cut between labels,
choose to auto-cut labels, advance the label tape, and
adjust the print contrast.

Printing Multiple Copies

You can print up to 99 copies of the same label at one
time.

To print multiple copies

1. Press # COPIES (SHIFT + PRINT).

2. Press the

3. Press the

4. Press OK or PRINT to begin printing.

between each label for more complex formats.

S arrow to increase the number of copies

to print. The default is 2 copies.

T arrow to decrease the number of

copies (maximum is 99).

You may notice a brief pause in printing

13

When printing is finished, the number of copies to
print returns to 2.

Collating Multiple Copies

When printing multiple copies of a label file containing
more than one label, all the copies of a label are
printed before the next label starts printing. You can
choose to have the label file print collated, so each
complete copy of the file prints before the second copy
starts. The following example shows three copies of a
label file containing three labels printed normally and
collated.

Normal

A101 A101 A101 A102 A102 A102 A103 A103 A103

Collated

A101 A102 A103 A101 A102 A103 A101 A102 A103

To collate multiple copies

1. Press SETTINGS.

2. Select Collate multi. copies and press OK.

3. Select On.

4. Press OK and then select Done (ESC).

Pausing between Labels

By default the printer pauses after printing each label
so you can cut the label. You can turn this feature off to
have the labels print continuously.

To set the printer to print continuously

1. Press SETTINGS.

2. Select Pause to cut btw labels and press OK.

3. Select Off.

4. Press OK and then select Done (ESC).

Advancing the Label Tape

The default leader space for all labels is approximately
10 mm. To add additional blank space to the
beginning or end of your label, you can feed the tape
in 10 mm increments.

To advance the tape

1. Press FEED (SHIFT + CUT).

2. Press OK to advance the tape.

Adjusting Print Contrast

Depending on the label material you choose, you may
need to lighten or darken the print on the label.

To adjust the print contrast

1. Press SETTINGS.

2. Select Print contrast and press OK.

3. Use the arrow keys to adjust the print contrast.

4. Press OK and then select Done (ESC).

5. Repeat as necessary until you are satisfied with the
print quality.

Using Printer Memory

The printer has a powerful memory feature that can
store label files for later recall. The number of label
files that can be stored is dependent on the size of the
label files and the number of images they contain. The
more images a file contains, the less memory that is
available for storing label files.

Saving a Label File

You can save label files for later use. When you save a
label file, all the label text and formatting are saved. A
label file name can be up to 20 alphanumeric
characters in length.

To save a label file

1. Create the labels in your label file.

2. Press SAVE.

3. Use the arrow keys to select New and press OK.

4. Enter a name for your label file and press OK.

5. Press CLR to start a new label.

14

Recalling a Label File from Memory

Once a label is saved to memory, you can recall the
label to print or edit. Recalling a label replaces the
current label.

To recall a label from memory

1. Press RECALL. The memory locations are displayed.

2. Use the arrow keys to move to the memory location
that contains the label you want and press OK.
A message appears confirming that you want to
clear the current label text and formatting.

3. Press OK.

Deleting a Label File from Memory

When you no longer need a stored label, you can
delete it from memory.

To delete a label from memory

1. Press RECALL. The saved label files are displayed.

2. Use the arrow keys to move to the label file you wish
to delete.

3. Press and then press OK to clear the memory
location.

Cleaning Your Printer

Your printer is designed to give you long and trouble­free service, while requiring very little maintenance.

Clea n your printer from time to time to keep it working
properly.

To clean the print head

1. Remove the tape cassette.

2. Remove the cleaning tool from inside the tape
cassette door.

3. Gently wipe the padded side of the tool across the
print head.

Using RHINO Connect Software

Your printer can be used as a standalone label printer
or you can print labels directly from your computer
using RHINO Connect Software. This software is
optional, and is not included with all printers.

RHINO Connect Software offers the following features:

• Upload and download label files for in-the-field and
on-demand printing

• Insert customized graphics, logos, symbols, and
industry terms

• Import data from any Windows program

• Create labels using the step-by-step wizard

• Print labels directly from RHINO Connect Software

Visi t www.dymo.com for more information about
obtaining the software. In addition, you can download
a free Windows printer driver so you can print directly
to your RHINO printer from any Windows application.

Connecting to your Computer

The printer connects to your computer using the USB
connection located on the bottom of the printer.

Figure 6

While data is being transferred between the
printer and your computer, PC Connected... Do not
disconnect is displayed on the printer and you cannot
use any of the printer functions.

Refer to the RHINO Connect Software Online Help for
complete information about using the printer while
connected to your computer.

15

Symbols

The following tables list the default symbols by category.

Electrical

Brackets

  Ω Ø ²
°


μ
λ

Voic e/Dat a



Audio/Video




Warning



Punctuation

, ; ' " .
: & \ ! ¡
~ ? ¿ _ *

+ - ± / =
≠ ÷ @ # %
< > ≤ ≥

( ) [ ]
{ }

Arrows

←↑→↓

Numbers

½ ¼ ¾

Home Electrical

   
    
   
    
   

    
  

Currency

$ ¢ £ ¥ €

16

Library Text

The following tables list the library text by category.

Location Audio

ATTIC KITCHEN
BACK LAUNDRY ROOM
BASEMENT LEFT
BATH LIBRARY
BEDROOM LIVING ROOM
BILLIARDS ROOM LOBBY
CENTER LOWER
CLOSET MAIN FLOOR
DECK MASTER BATH
DEMARC MASTER BEDROOM
DEN MEDIA ROOM
DINING ROOM OFFICE
DRESSING ROOM OUTSIDE
DRIVEWAY PATIO
FAMILY ROOM PLAY ROOM
FLOOR POOL
FOYER PORCH
FRONT RIGHT
GARAGE SITTING ROOM
GATE SPA
GUEST BATH STUDY
GUEST HOUSE SUNROOM
GUEST ROOM THEATER
GYM UPPER
HOT TUB UTILITY ROOM
INSIDE YARD

ANALOG PHONO
AUDIO RIGH T BACK SPKR
CD RIGHT FRONT SPKR
CENT FRONT SPKR RIGHT OUTD. SPKR
CENTER BACKSPKR RIGHT SIDE SPKR
DIGITAL RIGHT SURR. SPKR
LEFT BACK SPKR SPEAKER
LEFT FRONT SPKR SUBWOOFER
LEFT OUTD SPKR SURROUND
LEFT SIDE SPKR TAPE
LEFT SURR. SPKR VOLUME CONTROL
OPTICAL ZONE

Video

CATV RF
COMPO NENT RCB
COMPOSITE RS-232
DVD REMOTE
DVI S-VIDEO
DVR SAT
HDMI TV
HDTV TOUCH SCREEN
IR VCR
KEYPAD VESA
MONITOR VIDEO
NANNY CAM VIDEO GAME
PROJECTOR

17

Voice/ Data

CO LA N
CABLE MODEM LAPTOP
DSL NETWORK
DSLAM PHONE
DEMARC PHONE SYSTEM
DESKTOP USB
FAX VoI P
INTERNET WIRELESS

Security

BACK DOOR HEAT DETECTOR
CCTV HIGH WATER
CAMERA HORN
CARBON MONOXIDE LOW TEMP
CELL MOTION SENSOR
CONTACT PIR
CONTR OLLER PHONE
DOOR POOL
DOOR CONTACT POWER
DRIVEWAY REMOTE
DUAL TECH SENSOR
DUCT SHOCK SENSOR
FAN CUTO FF SIREN
FRONT DOOR SLIDERS
GARAGE DOOR SMOKE DETECTOR
GAS SPARE
GATE STROBE
GLASS BREAK WATER DETECTOR
GROUND

18

Troubleshooting

Review the following possible solutions if you encounter a problem while using your printer.

Problem/Error Message Solution

Battery Low
Battery Empty

Poor Print Quality • Clean the print head. See Cleaning Your Printer.

Tape Jam

Motor is stalled due to tape jam.

Uneven or slanted printing

The cassette is not inserted correctly.

Cannot close the tape cassette lid

The cassette is not inserted correctly.

Unable to return to the previous menu

Nothing shows on the display • Ensure the printer is turned on.

End of Tape

Tape cassette is empty.

• Attach the power adapter.

• Recharge the battery pack. See Recharging the Battery
Pack.

• Insert new AA alkaline batteries as a temporary power
source. AA batteries are less stable and should be used as a
temporary solution only.

• Adjust the Print Contrast. See Adjusting Print Contrast.

• Open the tape cassette compartment and press the eject
button to release the cassette.

• Remove the tape, clearing the jam.

• Make sure the tape passes smoothly through the
guideposts on the tape cassette. See Inserting and
Removing the Tape Cassette.

• When the jam is cleared, press

• Check the tape cassette compartment to make sure the
cassette is inserted properly. See Inserting and
Removing the Tape Cassette.

• Make sure the two levers in the tape compartment are
locked on either side of the cassette holding the cassette in
place.

Make sure nothing is blocking the cassette cover and that the
tape cassette is inserted properly. See Inserting and
Removing the Tape Cassette.

•Press

Esc to return to the previous menu.
Clr to return to return to the display and clear all

•Press
settings.

• Recharge battery pack or plug in power adapter.

• Remove power adapter and batteries and then reattach
power to restart the printer.

The printer cannot detect the end of the tape cassette. Make
sure you have tape left in the cassette before starting a large
print job.

OK to clear the display.

19

Problem/Error Message Solution

Display text is too light to read • Turn on backlight. See Using the Backlight.

•Adjust the display contrast. See Adjusting the Display
Contrast.

Too many lines

Too many lines for this tape width.

Barcode not allowed

Barcodes can only be printed on 19 mm and 24 mm tape.

Printing Self-Lam label not allowed

Self-Lam labels can only be printed on 24 mm Self-Laminated
tape.

Print error...

The tape is jammed.

No response when pressing keys

One of the keys may be jammed.

• Reduce the number of text lines.

• Insert a wider tape cassette.

• Replace the tape cassette.

• Change the tape width.

• Replace the tape cassette.

• Change the tape width.

• Open the tape cassette lid and check that the tape is not
jammed.

• Pull a small amount of tape from the cassette to make sure
the tape moves freely.

• Press each key to determine which key is jammed.

• Press the jammed key firmly until it returns to its normal
position.

If you still need assistance, contact DYMO Customer Support for your country. A list of contact numbers for each
country is listed inside the back cover of this User Guide.

20

Safety Precautions for Lithium-Ion Rechargeable Battery Pack

Inaccurate handling of Lithium-ion rechargeable battery may cause leakage, heat, smoke, an explosion, or fire.
This could cause deterioration of performance or failure. This may also damage the protection device installed in
the battery pack. This could damage equipment or injure users. Thoroughly follow the instructions below.

While Charging

èDanger

• When charging the battery, use dedicated chargers and follow the specified conditions.

• Do not connect directly to an electric outlet or cigarette lighter charger.

• Do not use or store battery close to fire or inside the car where temperature may be over 60°C.

èWarnin g

• Stop charging the battery if charging is not completed within the specified time.

èCaution

• Thoroughly read this user guide before charging the battery.

• Do not charge in a place that generates static elec tricity.

• Battery can only be charged within 0°C~45°C temperature range.

When Discharging the Battery

èDanger

• Use the battery only in the specified equipment.

• Do not use or store battery close to fire or inside the car where temperature may be over 60°C.

èCaution

• Do not charge in a place that generates static elec tricity.

• Battery can only be used within -20°C~60°C temperature range.

21

Documentation Feedback

We are constantly working to produce the highest quality documentation for our products. We welcome your
feedback.

Send us your comments or suggestions about our user guides. Please include the following information with your
feedback:

• Product name, version number, and page number

• Brief description of content (instructions that are inaccurate or unclear, areas where more detail is needed, and
so on)

We also welcome your suggestions about additional topics you would like to see covered in the documentation.
Send email messages to: [e-mail]
Please keep in mind that this email address is only for documentation feedback. If you have a technical question,

please contact Customer Support.

22

Contacting Customer Support

The following table provides a list of telephone numbers to reach DYMO Sales and Support departments. You can
also reach DYMO at www.dymo.com

Country Telephone Support Fax Support

Australia 1800/ 633 868 1800/ 817 558
België/Belgique 02/713 38 08 +31/ 20/ 581 93 80
Canada [phone]
Ceská Republika 02/619 12 720 02/619 12 730
Danmark 35 25 65 08 +31/ 20/ 581 93 80
Deutschland 069/ 66 56 85 29 +31/ 20/ 581 93 80
España 91/662 31 49 +31/ 20/ 581 93 80
France 01/69 32 49 32 +31/ 20/ 581 93 80
Hong Kong 02 2527 1928
Hungaria 1 424 6600 1 424 6601

International
Ireland 01 411 89 34
Italia 02/ 45 28 13 08 +31/ 20/ 581 93 80
Mexico 5368 2066
Nederland 020/581 93 86 020/ 581 93 80
New Zealand 0800 803 966 0800 737 212
Norge 22 97 17 10 +31/ 20/ 581 93 80
Österreich 01/ 599 14 20 12 02/627-400-160
Polska 022/349 15 02 +31/ 20/ 581 93 80
Portugal 21 120 61 64
Schweiz/Suisse 044 342 04 66 +31/ 20/ 581 93 80
Slovakia 02/619 12 720 02/619 12 730
Suomi 09 229 07 04 +31/ 20/ 581 93 80
Sverige 08/ 632 00 57 +31/ 20/ 581 93 80
Türkiye 212/ 286 26 30 PBX 212/ 286 26 28
United Kingdom 020/ 7341 55 29 +31/ 20/ 581 93 80
United States [phone]

a.Use the International number for all countries where no specific support number is listed.

a

.

[phone]

This product is CE marked in accordance with the EMC directive and the low voltage directive and is designed to conform with the following international standards:
US FCC Class B Compatibility

Safety - EN 60950, IEC 950, UL 1950
EMC Compatibility EN 61000 3-2/3; EN 61000 4-2/3/4/5/6/8/11; ENV 50204;

EU Immunity – EN 55024 & addendums A1, A2 Electromagnetic Compatibility (EMC) - Information Technology equipment, Immunity Characteristics

Emissions – EN 61000-6-3: Electromagnetic Compatibility (EMC) - Part 6: Generic Standards - Section 3: Emission standard for residential, commercial and light
industrial environments.

RoHS 2002/95/EC

www.sanford.com

Produced by:

DYMO

Stamford CT

800-426-7827: www.dymo.com

06902

A Newell Rubbermaid Company

© 2007 Sanford, L.P. All Rights Reserved. 09/07
No part of this document may be reproduced or transmit ted in any form or by any means or translated into another language without the prior written consent
of Sanford, L.P
RHINO and RHINO Connect are trademarks or registered trademarks of Sanford, L.P. All other trademarks are the property of their respective hold ers.