XNP693
XNP653
XNP553
SBX693
SBX653
SBX553
XNP-SBX SERIES
INSTALLATION/OWNER'S MANUAL
Car Audio Speakers
XNP - SBX SERIES PREPARATION
Getting Started
Thanks for choosing Dual. This manual is designed to provide information for
the purchaser of Dual car audio products. Dual has attempted to make sure
all the information in this manual is current. But, this information is subject to
change without notice.
Safety
This symbol with “CAUTION” is intended to alert the user
to the presence of important instructions. Failure to heed
the instructions can result in injury or unit damage.
To prevent injury and damage to the unit, please read
and follow the instructions in this manual.
If you feel unsure about installing this system yourself,
have it installed by a qualified audio technician.
Before installation, disconnect the battery negative
(-) terminal to prevent damage to the unit, fire and/or
possible injury.
Do not connect Amplifier or any audio source to
illumination inputs. Inputs are designed for 12 volt
power source only. More then 3Vrms connected to
illumination inputs may cause permanent damage to
the lighting elements.
2
XNP - SBX SERIES INSTALLATION
Installation
Please Note: Some Full Range Speakers are most often used as direct
replacements for stock speakers and are shipped without grilles or grilles
may not be required. Parts of the following instructions may not apply to your
installation.
The installation instructions included here are basic. If you feel
unsure about installing the speaker system, Dual recommends
that you seek installation by a qualified auto
sound technician.
Before installation, please follow these rules:
1. Be sure to carefully read and understand the instructions before
attempting to install the product.
2. For safety, disconnect the negative lead from the battery prior to beginning
the installation.
3. For easier assembly, we recommend that if additional wiring is required,
that you run all wires prior to mounting your speaker in place.
4. Use the highest quality connectors for a reliable installation and to
minimize signal or power loss.
5. Use caution before you drill or cut! Be careful not to cut or drill into gas
tanks, fuel lines, brake or hydraulic lines, vacuum lines or electrical
wiring when working on any vehicle.
6. Never run speaker wires underneath your vehicle. Running speaker wires
inside the vehicle provides the best protection from exhaust heat and
environmental elements.
7. Avoid running wires over, near, or through sharp edged surfaces. We
suggest you also use rubber grommets to protect any wires routed
through metal, especially the firewall.
8. Do not connect audio outputs from your amp or receiver to the Illuminite
inputs of the speakers. This WILL DAMAGE the LED bulbs and WILL void
your warranty.
3
XNP - SBX SERIES INSTALLATION
Audio Input
Terminals
Illuminite Lighting
Input Terminals
Lighting Hook-Up From Rear
Head unit
12 volt source
Ground
Lighting Hook-Up Recommendations
The illuminite lighting elements of your XiN series products provide you with a unique
custom touch to your vehicle. Dual’s patent pending illuminite bulb system and control
circuitry provides an extraordinary lighted-Hue illumination which allows great creative
opportunities for the beginner and seasoned custom installer alike. The interior of your
vehicle will never sound or look ordinary again. Let your imagination take you there.
The lighting features of all illuminite products require a 12 volt power source to operate.
The speaker has two distinct sets of input terminals. The first is labeled audio input
terminals and the second is labeled illuminite lighting inputs. The inputs are clearly
marked with a label positioned directly above the terminal housing. The polarity (+ and -)
indicators for each set of inputs also appear on these labels.
1. Do not connect Amplifier or any audio source to illuminite lighting inputs. Inputs are
designed for switched 12 volt power source only. More then 3V rms connected to
illumination inputs can cause permanent damage to the lighting elements.
2. See fig. 1a, (illustrates wiring diagram) be sure to maintain polarity. Be sure to connect
to a constant switched 12 volt source. Correct connection would be the positive (+) 12
volt wire to the Positive (+) illuminite Lighting input terminal and connect the Negative
(-) illuminite lighting input terminal to a good chassis ground.
Fig 1a
Notice: The Illuminite™ series LED illumination elements are not removable. There
are no serviceable parts inside or attached to the speaker assembly. The Illuminite™
series products are sensitive electronic devices. Removal or tampering with any part or
portion of the speaker and/or its assemblies will damage the product and void the limited
warranty.
4
XNP - SBX SERIES INSTALLATION
Mounting
1. Determine where the speakers will
be mounted. Ensure an area large
enough for the speaker to mount
evenly. Be sure that the mounting
location is deep enough for the
speaker to fit.
2. Refer to the specification chart to
determine the proper diameter hole
to cut for your speaker model.
3. If supplied, use the plastic mounting
ring as a template to mark the
locations for the mounting screws.
Drill the holes with a 1/8" bit.
4. Be sure to observe proper polarity
when connecting the wires.
The speaker's positive terminal is
indicated with the “+” symbol.
5.
Fit the ring and speaker to the cut-out.
Mount them using the enclosed screws.
If supplied, fit the grille inside the ring
and press gently, but firmly, into place
and attach with screws.
5
XNP - SBX SERIES INSTALLATION
Mounting Legend
6
Notes
XNP - SBX SERIES SPECIFICATIONS
7
XNP - SBX SERIES WARRANTY
Limited One-Year Warranty
This warranty gives you specific legal rights.
You may also have other rights which vary from
state to state.
Namsung America Inc. warrants this product to
the original purchaser to be free from defects
in material and workmanship, under normal
conditions, for a period of one year from the date
of the original purchase.
Namsung America agrees, at our option, during
the warranty period, to repair any defect in
material or workmanship or to furnish an equal
new or renewed product in exchange without
charges, subject to verification of the defect or
malfunction and proof of the date of purchase.
During the One-Year Warranty Period: For One
Year from the date of purchase, your product will
be replaced with a new, renewed or comparable
product (whichever is deemed necessary) if it
becomes defective or inoperative. This is done
without charge to you. Replacement products are
warranted for the balance of the original warranty
period.
Who is covered? This warranty is extended to the
original retail purchaser for products purchased
and used in the U.S.A., in the 48 contiguous states
ONLY.
What is covered? This warranty covers all defects
in material and workmanship in this product. The
following are not covered: installation/removal
costs, damage resulting from accident, misuse,
abuse, neglect, product modification, improper
installation, incorrect line voltage, unauthorized
repair or failure to follow instructions supplied
with the product, or damage occurring during
return shipment of the product.
What to do?
1. Before you call for service, check your operating
instruction booklet. A slight adjustment of any
custom controls discussed in your instruction
booklet may save you a service call.
2. If you require service during the warranty
period, you must carefully pack the product
(preferably in the original package) and ship it by
prepaid transportation with proof of the purchase
date from the retailer to the Return Center
address listed below.
3. Please describe your problem in writing
and include your name, a return UPS shipping
address (P.O. Box not acceptable), and a daytime
phone number with your shipment.
4. DUAL will pay the return shipping charges if
the product is returned to an address within the
USA.
Namsung America Inc.
Attn: Returns Center
21318 64th Ave. South
Kent, WA 98032 U.S.A.
Toll Free: 1-866-626-7863
Exclusion of Certain Damages: This warranty
is exclusive and in lieu of any and all other
warranties, expressed or implied, including
without limitation the implied warranties of
merchantability and fitness for a particular
purpose and any obligation, liability, right, claim
or remedy in contract or tort, whether or not
arising from the company’s negligence, actual
or imputed. No person or representative is
authorized to assume for the company any other
liability in connection with the sale of this product.
In no event shall the company be liable for
indirect, incidental or consequential damages.
Dual Electronics Corporation
21318 64th Avenue South
Kent, WA 98032 U.S.A
©2005 Dual Electronics Corp.
www.dualav.com
EVOK0404-V01
Loading...