Page 1
Installation
Before You Start
• Consult a qualified technician for instructions. Dual always recommends
professional installation.
• Disconnect negative battery terminal.
• Remove trim ring from unit (if installed).
• Remove 2 transit screws located on top of the unit (if applicable).
• Insert the removal keys, and remove the mounting sleeve from the head unit.
Note: Most vehicles require an installation kit, wiring harness and/or antenna
adapter (all sold separately) to properly install the head unit in the vehicle.
Installation Process
Quick Start Guide
For Mechless and CD Receivers
Not all features listed in this QSG
are available on all models.
e
r
y
o
o
f
e
u
b
k
n
i
h
t
p
r
i
n
t
To download the complete,
model-specific manual, please visit
www.dualav.com/support/manuals.php
or call 1-866-382-5476,
9AM-5PM EST (Monday-Friday).
1. Carefully remove the existing head unit.
2. Connect wiring harness. Consult a qualified technician if you are unsure.
3. Mount the head unit using the mounting sleeve or ISO brackets (depending
on your vehicle’s dashboard).
4. Connect wiring harness and antenna. Test the head unit for correct operation.
5. Slide into mounting sleeve to secure, or mount the ISO brackets to the
vehicle.
6. Snap trim ring into place.
Wiring Connections
The chart below the connection for each wire in the wiring harness.
Color Connection
Red 12V Ignition / Accessory
Yellow 12V Battery / Memory
Black Ground
Blue Power Antenna / Amp Turn-on
Grey Right Front (+)
Grey/Black Right Front (-)
White Left Front (+)
White/Black Left Front (-)
Violet Right Rear (+)
Violet/Black Right Rear (-)
Green Left Rear (+)
Green/Black Left Rear (-)
When a suitable ground wire is
not present in the vehicle wiring
harness, connect the black ground
wire to the vehicle chassis.
When replacing the fuse, make
sure new fuse is the correct type
and amperage. Using an incorrect
fuse could damage the radio.
Tip:
Fuse:
Mounting the Head Unit:
Typical DIN mounting
Step 1:
Insert the mounting sleeve into the
installation kit or dashboard.
Step 2:
Bend multiple mounting tabs around
the mounting sleeve until the
mounting sleeve is secure.
Step 3:
Connect all wiring harnesses and
slide the head unit into the mounting
sleeve until it clicks into place.
Mounting the Head Unit:
ISO mounting
Using the existing brackets or the
brackets supplied with the installation
kit, mount the brackets to the sides of
the head unit with the screws supplied
Installation
Dashboard or Installation Kit
Mounting Tabs
Dashboard or Installation Kit
Head Unit
Decorative
Bezel
Dashboard or Installation Kit
Mounting Sleeve
Mounting Sleeve
Mounting Sleeve
New
Radio
Existing
Brackets
with the head unit.
Power On/Off
Faceplate Removal
Changing Modes
Volume
Mute
Auxiliary Inputs
Reset
Setting the Clock
Display
Audio / Menu
To download the complete Owner’s Manual for your radio,
please visit www.dualav.com/support/manuals.php.
General Operation
Press the button to turn the unit on. Press again to
turn unit off.
Press RELEASE and pull away from the left side to
remove. To re-install, insert right side of faceplate
first then push left side to secure.
Press MODE to select between AM/FM, CD player,
auxiliary front/rear, USB and operation of iPod/iPhone.
Modes of operation are shown in the
display.
Adjust volume using volume knob.
Press to silence the audio. Press again to resume
listening at the previously selected volume.
Insert a 3.5mm cable in the units front AUX port, or RCA
cables into the rear AUX-IN connectors.
Press the RESET button to reset the unit back to the
factory settings if abnormal operation occurs. The reset
button is located behind the front panel.
With the unit on, press and hold DISP until the clock
begins to flash, then release. Press TUNE
the hours and TUNE
DISP momentarily to save the selected time.
Press DISP to toggle display between various displayed
information.
Press and hold AUDIO/MENU for more than three
seconds to access the setup menu. Press AUDIO/MENU
momentarily to select between the menu functions and
rotate the volume knob left/right to adjust or activiate the
desired function.
to adjust the minutes. Press
ll
to adjust
nn
AM/FM Tuner Operation
Seek Tuning
Manual Tuning
Storing Presets
Recalling Presets
To download the complete Owner’s Manual for your radio,
Press TUNE
second to seek to the next strong station.
Press TUNE
radio frequency up or down one step at a time. Press and
hold to advance quickly.
Band
Press BAND to select between FM1, FM2, FM3, AM1
and AM2 bands. Up to six presets can be programmed
for each band, enabling up to 18 FM stations and 12 AM
stations to be stored in memory.
Up to 18 FM and 12 AM stations can be stored. To store
a station, select the desired band and station. Press and
hold the desired preset button (1-6) for more than two
seconds. When stored, the preset number will appear in
the display.
Preset stations can be recalled any time by pressing the
corresponding preset button.
please visit www.dualav.com/support/manuals.php.
or TUNE
nn
or TUNE
nn
for more than one
ll
momentarily to move
ll
CD Operation*
Insert CD
Eject CD
Track Select
Fast Forward/
Reverse
Repeat
Random
CD-R/CD-RW
Compatibility
To download the complete Owner’s Manual for your radio,
With the label facing up, insert a standard size CD into
the CD slot. Playback will begin automatically.
Press EJECT (located behind the front panel) to eject the
CD. The unit will change to previous mode of operation.
Press TUNE
track. Press TUNE
current track. Pressing TUNE
beginning of the previous track.
Press and hold TUNE
or reverse a track.
Pause
Press
l
Press
l
Intro
Press INT to access the Intro menu, then turn the volume
knob to select one of the following:
• OFF - Cancels the INT function.
• ALL - Plays the first 10 seconds of each track.
Press RPT to access the Repeat menu, then turn the
volume knob to select one of the following:
• ALL - Plays all tracks on CD.
• TRACK - Continuously repeats selected track.
Press RDM to access the Random menu, then turn
the volume knob to select one of the following:
• OFF - Cancels the RDM function.
• ALL - Plays all tracks in random order.
Some CD-Rs and CD-RWs may be incompatible
with this unit, depending on media type and
recording method. Refer to the online owner’s
manual for details.
* Not available on all models.
please visit www.dualav.com/support/manuals.php.
to skip to the beginning of the next
ll
to return to the beginning of the
nn
nn
or TUNE
ll
/ II to temporarily stop CD playback.
/ II again to resume playback.
again skips to the
to fast forward
nn
Playing MP3/WMA
Fast Forward and
Files
Track Select
Reverse
Pause
Folder Access
Repeat
Random
Intro
To download the complete Owner’s Manual for your radio,
please visit www.dualav.com/support/manuals.php.
MP3 / WMA Operation *
To play MP3/WMA files, insert a data CD, SD card or USB
device containing MP3/WMA files.
Press TUNE
Press TUNE
song. Pressing TUNE
the previous song.
Press and hold TUNE
or reverse a track.
Press l/ II to temporarily stop playback.
Press l/ II again to resume playback.
Press to select the next folder. Press to select the
previous folder. Folder access is only available on discs or
devices with more than one folder.
Press RPT to enter the Repeat menu, then turn the volume
knob to select one of the following options:
• ALL - Plays all tracks on disc or device.
• TRACK - Continuously repeats selected track.
• FOLDER - Continuously repeats all files in folder.
Press RDM to enter the Random menu, then turn the
volume knob to select one of the following options:
• OFF - Cancels RDM function.
• ALL - Plays all tracks in random order.
• FOLDER - Plays all tracks in folder in random order.
Press INT to enter the Intro menu, then turn the volume
knob to select one of the following options:
• OFF - Cancels the INT function.
• ALL - Plays first 10 seconds of each track.
• FOLDER - Plays first 10 seconds of each track in the
selected folder.
* Not available on all models.
to skip to the beginning of the next song.
ll
to return to the beginning of the current
nn
again skips to the beginning of
nn
or TUNE
ll
to fast forward
nn
Connect an iPod/
iPhone Device (sold
separately)
Song Select
Forward/Reverse
Pause
Repeat
Random
Intro
Music Search
Manual Control
for iPod
To download the complete Owner’s Manual for your radio,
please visit www.dualav.com/support/manuals.php.
Operation of iPod/iPhone*
To play music from an iPod/iPhone device, connect the USB
cable (included with your iPod/iPhone device) to the unit’s USB
port. Playback will begin automatically.
Press
the beginning of the current song. Pressing
to the beginning of the previous song.
Press and hold
Press
Press
Press RPT to enter the Repeat menu, then turn the volume
knob to select one of the following options:
• ALL - Repeats all tracks.
• SONG - Continuously repeats selected track.
Press RDM to enter the Random menu, then turn the volume
knob to select one of the following options:
• OFF- Cancels the RDM function.
• ALL - Plays all tracks in random order.
• ALBUM - Plays all tracks in album in random order.
Press INT to enter the Intro menu, then turn the volume knob
to select one of the following options:
• OFF - Cancels the INT function.
• ON - Plays first 10 seconds of each track.
Turn the volume knob to select between artists,
songs, playlists, podcasts and audiobooks. Press SELECT to
select the desired search category. Most search categories
have subcategories to navigate through.
When “MANUAL” control is selected from the Setup Menu,
the iPod or iPhone device can be controlled directly from the
device’s interface. All functions except for volume can be used
from the iPod or i Phone device.
Note: The firmware of the iPod/iPhone must be up dated to the
latest version to be compatible with manual control model. Not
all devices are compatible with manual control mode.
to skip to the next song. Press
ll
or
ll
/ II to temporarily stop playback.
l
/ II again to resume playback.
l
* Not available on all models.
to fast forward or reverse.
nn
to return to
nn
again skips
nn
albums,
Bluetooth® Operation*
Preparation
Pairing a New
Device
Pairing
Additional
Devices
Disconnecting a
Device
Streaming Audio
Troubleshooting
To download the complete Owner’s Manual for your radio,
please visit www.dualav.com/support/manuals.php.
Before using a Bluetooth device, it must be paired and
connected. Ensure that Bluetooth is activated on your
device before beginning the pairing process.
The head unit broadcasts the pairing signal constantly
when no devices are connected. Complete the pairing
sequence from your Bluetooth device. Refer to the
owner’s manual for your device for more details.
The device name is “DUAL BT”
The Bluetooth passcode “1234”
Note: The head unit can be in any mode of operation
when pairing is performed.
If a device is currently connected, press and hold
to disconnect the current device before a new device
can be paired. Then begin the pairing sequence from
the new Bluetooth device.
Press and hold for 3 seconds to disconnect a
connected device. The device will remain paired and
appear in the SEARCH menu, but not be connected.
The head unit supports A2DP wireless streaming audio
from a Bluetooth mobile device directly to your head unit.
The following functions can be used to control the music:
• Press
• Press
• Press
playback.
* Not available on all models.
to skip to the next available audio track.
ll
to skip to the previous audio track.
nn
/
II
to toggle between play and pause during
l
Requirements
USB Connection
Changing Stations
Shuffle
Skip Track
Play/Pause
Thumbs Up
Thumbs Down
Device
Compatibility
To download the complete Owner’s Manual for your radio,
please visit www.dualav.com/support/manuals.php.
Pandora® Operation*
Control for Pandora requires:
• An iPhone device with a reliable data connection, or an
iPod touch that is connected to wireless internet.
• The Pandora App installed on the iPhone/iPod device.
• An active account with Pandora (www.pandora.com).
• The USB sync cable included with iPod/iPhone device.
Connect an iPod touch or iPhone device (required, sold
separtely) to the USB port, using the USB sync cable
included with your iPhone device.
Press SELECT to display the stations menu. Turn the
volume knob to cycle through the list of stations, then
press SELECT when the desired station is highlighted.
Note: Stations must be created on your account prior to
connecting your iPod/iPhone device to the head unit.
Press SELECT to display the stations menu. Choose
“Shuffle” from the stations menu to shuffle songs from all
of your stations.
Press
Press
Press
Press
the currently playing song.
Press
different from the currently playing song.
Refer to the Owner’s Manual for a complete list of devices
compatible with this head unit. Refer to www.pandora.
com/everywhere/mobile for devices compatible with the
Pandora mobile application.
gnitoohselbuorT
Note: Pandora is an internet service, carrier and data
charges may apply.
to skip the current song.
ll
/ II to temporarily stop playback.
l
/ II again to resume playback.
l
to customize the station to play more songs like
to customize the station to play songs that are
* Not available on all models.
This warranty gives you specific legal rights. You may also have other rights which
vary from state to state. Dual Electronics Corp. warrants this product to the original
purchaser to be free from defects in material and workmanship for a period of
one year from the date of the original purchase. (Note that select marine products
carry a 2-year warranty. Please visit www.dualav.com for details.) Dual Electronics
Corp. agrees, at our option, during the warranty period, to repair any defect in
material or workmanship or to furnish an equal new, renewed or comparable
product (whichever is deemed necessary) in exchange without charges, subject
to verification of the defect or malfunction and proof of the date of purchase.
Subsequent replacement products are warranted for the balance of the original
warranty period.
Who is covered? This warranty is extended to the original retail purchaser for
products purchased and used in the U.S.A.
What is covered? This warranty covers all defects in material and workmanship
in this product. The following are not covered: installation/removal costs, damage
resulting from accident, misuse, abuse, neglect, product modification, improper
installation, incorrect line voltage, unauthorized repair or failure to follow
instructions supplied with the product, or
of the product.
What to do?
1. Before you call for service, check the troubleshooting guide in your owner’s
manual. A slight adjustment of any custom controls may save you a service call.
2. If you require service during the warranty period, you must carefully pack the
product (preferably in the original package) and ship it by prepaid transportation
with a copy of the original receipt from the retailer to an authorized service
center.
3. Please describe your problem in writing and include your name, a return UPS
shipping address (P.O. Box not acceptable), and a daytime phone number with
your shipment.
4. For more information and for the location of the nearest authorized service center
please contact us toll-free at 1-866-382-5476 or by email at cs@dualav.com.
Exclusion of Certain Damages: This warranty is exclusive and in lieu of any
and all other warranties, expressed or implied, including without limitation the
implied warranties of merchantability and fitness for a particular purpose and any
obligation, liability, right, claim or remedy in contract or tort, whether or not arising
from the company’s negligence, actual or imputed. No person or representative is
authorized to assume for the company any other liability in connection with the sale
of this
consequential damages.
Limited One-Year Warranty
damage occurring during return shipment
product. In no event shall the company be liable for indirect, incidental or
FCC Compliance
This device complies with Part 15 of the FCC Rules. Operation is subject to the following
two conditions:
(1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that may
cause undesired operation.
Warning: Changes or modifications to this unit not expressly approved by the party
responsible for compliance could void the user’s authority to operate the equipment.
Note: This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This
equipment generates, uses and can radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by one or more of the following
measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
Dual Electronics Corp.
Toll Free: 1-866-382-5476
Monday-Friday, 9AM-5PM
www.dualav.com
©2014 Dual Electronics Corp. All rights reserved.
iPhone, iPod, iPod classic, iPod nano, and iPod touch are trademarks of Apple Inc., registered in the U.S. and other countries.
“Made for iPod” and “Made for iPhone” mean that an electronic accessory has been designed to connect specifically to iPod or iPhone,
respectively, and has been certified by the developer to meet Apple performance standards. Apple is not responsible for the operation of
this device or its compliance with safety and regulatory standards. Please note that the use of this accessory with iPod or iPhone may affect
The Bluetooth® word mark and logos are owned by the Bluetooth SIG, Inc. and any use of such marks by Namsung is under license.
Pandora, the Pandora logo, and the Pandora trade dress are trademarks of Pandora Media, Inc., used with permission.
The SD logo is a trademark of the SD Card Association.
wireless performance.
Other trademarks and trade names are those of their respective owners.
NSA0214-V01
Loading...