D-Link DFL-200 User Manual

Page 1
This product can be set up using any current web browser, i.e., Internet Explorer 6 or Netscape Navigator 6.
Network Security
Firewall
5V DC Power Adapter
If you purchased this Network Security Firewall to connect to your high-speed
Internet connection in a secure manner, you must have either an Ethernet-based Cable or DSL modem with an established Internet account from an Internet Service Provider (ISP).
Check Your Package Contents
CD-ROM (containing Manual and Warranty)
Ethernet (CAT5 UTP/Straight Through) Cable
Using a power
supply with
If any of the above items are missing, please contact your reseller.
DFL-200
©
Console Cable (RS 232)
Page 2
A.
First, connect the power adapter to the
at the back panel of the DFL-
to indicate proper operation.
B.
1. Power off your Cable or DSL modem; some devices may not have a on/off switch and will require you to unplug the power adapter. Now, the DFL-200 should be powered on and the Cable / DSL modem should be turned off.
2. Cable / DSL modem (Power Off
) – DFL-200 (Power On) Connect an Ethernet cable to the Ethernet jack located on the Cable / DSL modem. After the Ethernet cable is securely connected, power on the Cable / DSL modem by turning on the unit or plugging in the power adapter.
3. Cable / DSL modem (
Power On) – DFL-200 (Power On)
Insert the other end of the Ethernet cable to the WAN port on the back panel of the DFL-200. The WAN LED light will illuminate to indicate proper connection. If the WAN LED is not illuminated, please go back to step B and repeat its instructions.
C.
Insert an Ethernet cable to one of the
LAN ports on the back panel of the
D.
Connect the computer that you will use to confi gure the DFL-200 to the
WAN port
COM Port
Power Adapter
LAN ports
These are
for connecting Ethernet
DMZ port
This is for
Reset
system
factory defaults
Page 3
POWER LED – a solid light indicates a proper connection to the power supply.
NETWORK LEDs – a solid light on the port indicates a connection to an Ethernet enabled computer. These LEDs blinks during data transmission.
Restart your computer
To obtain a new IP address from the DFL-200 you wll need to restart your computer. Make sure that the network adapter in your computer is confi gured properly fi rst. Instructions on how to confi gure the network adapter to obtain an IP address automatically from the DFL-200 can be found in the appendix.
STATUS LED – will fl ash consistently to indicate that the DFL-200 is working properly.
Page 4
When you have completed the steps in this
Quick Installation
Guide, your connected network should look similar to this:
and
“http://192.168.1.1”
into the
or
Activate your browser. Then type the IP address of the DFL-200
Page 5
The Setup Wizard
Step 2 - Set timezone
the password
for the admin account.
NEXT
Step 1 - Set admin password
the appropriate
NEXT
the appropriate
Welcome to the DFL-200 connection wizard!
Connect to the unit via
HTTPS instead
NEXT
to keep
Page 6
The Setup Wizard
If you are unsure of which setting to select, please contact your Internet Service Provider
Step 3 - Confi gure WAN interface
Select the appropriate confi guration for the WAN interface, if you are unsure of which setting to select, please contact your Internet Service Provider.
Click Next and continue to step 4 further down.
Next
Page 7
Step 3 - PPPoE
The Setup Wizard
Next
Step 3 - Static IP
If you selected Static IP you have to fi ll out the IP address information provided to you by your ISP. You will need to complete all the required fi elds except for Secondary DNS Server. You should probably not use the numbers displayed in these fi elds, they are only used as an example.
Click Next and continue to step 4 further down.
Next
If you selected PPPoE (Point­to-Point Protocol over Ethernet) you will have to fi ll out the user name and password provided to you by your ISP. The PPPoE Service Name fi eld should be left blank unless your ISP informs you otherwise.
Click Next and continue to step 4 further down.
Page 8
If you selected PPTP you will need to specify both PPTP
tunnel parameters and Physical interface parameters.
PPTP tunnel parameters:
Enter the Username, Password and the PPTP Server IP address provided by your ISP.
Physical interface parameters:
DHCP
If your Internet Service Provider is using DHCP you should select the DHCP radio button.
Static IP
If your Internet Service Provider is using Static IP you should select the Static IP radio button and enter IP Address, choose a Subnet Mask and enter the Gateway IP address.
The Setup Wizard
Next
Step 3 - PPTP
Page 9
The Setup Wizard
Next
Step 3 - Big Pond
If you selected Big Pond you will have to fi ll out the user name and password provided to you by your ISP.
Click Next and continue to step 4 further down.
Page 10
If you want to use the built-in DHCP Server in the DFL-200, choose Enable DHCP Server in this screen. You then need to specify a range of IP addresses to hand out to the DHCP clients. This range is entered in the format “Start IP – Stop IP” i.e.
192.168.1.100 – 192.168.1.200. If you don’t want to use the built­in DHCP Server or confi gure it later, choose Disable DHCP Server and click Next when done.
The Setup Wizard
Next
Step 4 - Set up built-in DHCP server
Next
Step 5 - Confi gure helper servers
- If enabled,
– If enabled,
Page 11
The Setup Wizard
Restart
Setup Wizard Complete
Click Restart to complete your confi guration.
Page 12
To connect to the network, make sure the network adapter in your computer is confi gured properly. Here’s how to confi gure the network adapter to obtain an IP address automatically from the DFL-200 Network Security Firewall.
Restart
your
OK
Internet Protocol (TCP/IP)
Properties
Obtain an IP address
automatically
Microsoft Windows XP:
My Network Places
>
on the
associated
with the Ethernet adapter (i.e., D-Link
Page 13
Apple Macintosh OS X:
Network
System Preferences
The IP address information, the Subnet Mask, the DFL-200 IP address and the Ethernet adapter address will appear
Network
Apply Now
Using DHCP
in
Built-in Ethernet
Page 14
Technical Support
You can fi nd software updates and user documentation on the D-Link website.
D-Link provides free technical support for customers within the United States and
within Canada for the duration of the warranty period on this product.
U.S. and Canadian customers can contact D-Link technical support through our
website, or by phone.
Tech Support for customers within the United States:
D-Link Technical Support over the Telephone:
(877) 453-5465
6am-6pm PST, Mon-Fri.
D-Link Technical Support over the Internet:
http://support.dlink.com
email:support@dlink.com
Tech Support for customers within Canada:
D-Link Technical Support over the Telephone:
(800) 361-5265
Monday to Friday 8:30am to 9:00pm EST
D-Link Technical Support over the Internet:
http://support.dlink.ca
email:support@dlink.ca
Tech Support for customers within
the United Kingdom & Ireland:
D-Link UK & Ireland Technical Support over the Telephone:
+44 (0)20 7365 8440 (United kingdom)
+353 (0)12 421 061 (Ireland)
Monday to Friday 8:00 am to 10:00 pm
D-Link Technical Support over the Internet:
http://www.dlink.co.uk
Loading...