D-Link DES-1016D User Manual

DES-1016D

10/100 NWay Ethernet/

Fast Ethernet Switch

User’s Guide

First Edition (Sept., 1999)

6DES1016D.02

Printed In Taiwan

RECYCLABLE

Wichtige Sicherheitshinweise

1. Bitte lesen Sie sich diese Hinweise sorgfältig durch.

2. Heben Sie diese Anleitung für den spätern Gebrauch auf.

3. Vor jedem Reinige n ist das Gerät vom Stromne tz zu trennen. Vervenden Sie keine Flüssig­oder Aerosolreiniger. Am besten dient ein angefeuchtetes Tuch zur Reinigung.

4. Um eine Beschädigung des Gerätes zu vermeiden sollten Sie nur Zubehörteile verwenden,
die vom Hersteller zugelassen sind.

5. Das Gerät is vor Feuchtigkeit zu schützen.

6. Bei der Aufstellung des Gerätes ist auf sichern Stand zu achten. Ein Kippen oder Fallen
könnte Verletzungen hervorrufen. Verwenden Sie nur sichere Standorte und beachten Sie
die Aufstellhinweise des Herstellers.

7. Die Belüftungsöffnungen dienen zur Luftzirkulation die das Gerät vor Überhitzung schützt.
Sorgen Sie dafür, daß diese Öffnungen nicht abgedeckt werden.

8. Beachten Sie beim Anschluß an das Stromnetz die Anschlußwerte.

9. Die Netzanschlußsteckdose muß aus Gründen der elektrischen Sicherheit einen
Schutzleiterkontakt haben.

10. Verlegen Sie die Netzanschlußleitung so, daß niemand darüber fallen kann. Es sollete auch
nichts auf der Leitung abgestellt werden.

11. Alle Hinweise und Warnungen die sich am Geräten befinden sind zu beachten.

12. Wird das Gerät über einen längeren Zeitraum nicht benutzt, sollten Sie es vom Stromnetz
trennen. Somit wird im Falle einer Überspannung eine Beschädigung vermieden.

13. Durch die Lüftungsöffnungen dürfen niemals Gegenstände oder Flüssigkeiten in das Gerät
gelangen. Dies könnte einen Brand bzw. Elektrischen Schlag auslösen.

14. Öffnen Sie niemals das Gerät. Das Gerät darf aus Gründen der elektrischen Sicherheit nur
von authorisiertem Servicepersonal geöffnet werden.

15. Wenn folgende Situationen auftreten ist das Gerät vom Stromnetz zu trennen und von einer
qualifizierten Servicestelle zu überprüfen:

a – Netzkabel oder Netzstecker sint beschädigt.
b – Flüssigkeit ist in das Gerät eingedrungen.
c – Das Gerät war Feuchtigkeit ausgesetzt.
d – Wenn das Gerät nicht der Bedienungsanleitung ensprechend funktioniert oder Sie mit

Hilfe dieser Anleitung keine Verbesserung erzielen.
e – Das Gerät ist gefallen und/oder das Gehäuse ist beschädigt.
f – Wenn das Gerät deutliche Anzeichen eines Defektes aufweist.

16. Bei Reparaturen dürfen nur Orginalersatzteile bzw. den Orginalteilen entsprechende Teile
verwendet werden. Der Einsatz von ungeeigneten Ersatzteilen kann eine weitere
Beschädigung hervorrufen.

17. Wenden Sie sich mit allen Fragen die Service und Repartur betreffen an Ihren
Servicepartner. Somit stellen Sie die Betriebssicherheit des Gerätes sicher.

18. Zum Netzanschluß dieses Gerätes ist eine geprüfte Leitung zu verwenden, Für einen
Nennstrom bis 6A und einem Gerätegewicht grßer 3kg ist eine
Leitung nicht leichter als H05VV-F, 3G, 0.75mm2 einzusetzen.

Limited Warranty

Hardware:

D-Link warrants each of its hardware products to be free from defects in workmanship and
materials under normal use and service for a period commencing on the date of purchase from
D-Link or its Authorized Reseller and extending for the length of time stipulated by the
Authorized Reseller or D-Link Branch Office nearest to the place of purch ase.

This Warranty applies on the condition that the product Registration Card is filled out and
returned to a D-Link office within ninety (90) days of purchase. A list of D-Link offices is
provided at the back of this manual, together with a copy of the Registration Card.

If the product proves defective within the applicable warranty period, D-Link will provide repair
or replacement of the product. D-Link shall have the sole discretion whether to repair or
replace, and replacement product may be new or reconditioned. Replacement product shall be of
equivalent or better specifications, relative to the defective product, but need not be identical.
Any product or part repaired by D-Link pursuant to this warranty shall have a warranty period
of not less than 90 days, from date of such repair, irrespective of any earlier expiration of original
warranty period. When D-Link provides replacement, then the defective product becomes the
property of D-Link.

Warranty service may be obtained by contacting a D-Link office within the applicable warranty
period, and requesting a Return Material Authori z ation (RMA) number. If a Registration Card
for the product in question has not been returned to D-Link, then a proof of purch ase (such as a
copy of the dated purchase invoice) must be provided. If Purchaser's circumstances require
special handlin g of warranty correction, then at the time of requesting RMA number, Pu rchaser
may also propose special procedure as may be suitable to the case.

After an RMA number is issued, the defective product must be packaged securely in the original
or other suitable shipping package to ensure that it will not be damaged in transit, and the RMA
number must be prominently marked on the outside of the package. The package must be
mailed or otherwise shipped to D-Link with all costs of mailing/shipping/insurance prepaid.
D-Link shall never be responsible for any softwa re, firmware, information, or memory data of
Purchaser contained in, stored on, or integrated with any product returned to D-Link pursuant
to this warranty.

Any package returned to D-Link without an RMA number will be rejected and shipped back to
Purchaser at Purchaser's expense, and D-Link reserves the right in such a case to levy a
reasonable handling charge in addition mailing or shipping costs.

Software:

Warranty service for software products may be obtained by contacting a D-Link office within the
applicable warranty period. A list of D-Link offices is provided at the back of this manual,
together with a copy of the Registratio n Card. If a Registra tion Card for the product in question
has not been returned to a D-Link office, then a proof of purchase (such as a copy of the dated
purchase invoice) must be provided when requesting warranty service. The term "purchase" in
this software warranty refers to the purchase transaction and resulting license to use such
software.

D-Link warrants that its software products will perform in substantial conformance with the
applicable product documentation provided by D-Link with such software product, for a period of
ninety (90) days from the date of purchase from D-Link or its Authorized Reseller. D-Link

warrants the magnetic media, on which D-Link provides its software product, against failure
during the same warranty period. This warranty applies to purchased software, and to
replacement software provided by D-Link pursuant to this warranty, but shall not apply to any
update or replacement which may be provided for download via the Internet, or to any update
which may otherwise be provided free of charge.

D-Link's sole obligation under this software warranty shall be to replace any defective software
product with product which substantially conforms to D-Link's applicable product
documentation. Purchaser assumes responsibility for the selection of appropriate application
and system/platform software and associated reference materials. D-Link makes no warranty
that its software products will work in combination with any hardware, or any application or
system/platform software product provided by any third party, excepting only such products as
are expressly represented, in D-Link's applicable product documentation as being compatible.
D-Link's obligation under this warranty shall be a reasonable effort to provide compatibility, but
D-Link shall have no obligation to provide compatibility when there is fault in the third-party
hardware or software. D-Link makes no warranty that operation of its software products will be
uninterrupted or absolutely error-free, and no warranty that all defects in the software product,
within or without the scope of D-Link's applicable product documentation, will be corrected.

D-Link Offices for Registration and Warranty Service

The product's Registration Card, provided at the back of this manual, must be sent to a D-Link
office. To obtain an RMA number for warranty service as to a hardware product, or to obtain
warranty service as to a software product, contact the D-Link office nearest you. An
address/telephone/fax/e-mail/Web site list of D-Link offices is provided in the back of this manual

LIMITATION OF WARRANTIES

IF THE D-LINK PRODUCT DOES N OT OPERATE AS WARRANTED ABOVE,
THE CUSTOMER'S SOLE REMEDY SHALL BE, AT D-LINK'S OPTION, REPAIR
OR REPLACEMENT. THE FOREGOING WARRANTIES AND REMEDIES ARE
EXCLUSIVE AND ARE IN LIEU OF ALL OTHER WARRANTIES, EXPRESSED
OR IMPLIED, EITHER IN FACT OR BY OPERAT ION OF LAW, STATUTORY OR
OTHERWISE, INCLUDING W ARRANTIES OF MERCHANTABILITY AND
FITNESS FOR A PARTICULAR PURPOSE. D-LINK NEITHER ASSUMES NOR
AUTHORIZES ANY OTHER PERSON TO ASSU ME FOR IT ANY OTHER
LIABILITY IN CONNECTION WITH THE SALE, INSTALLAT ION,
MAINTENANCE OR USE OF D-LINK'S PRODUCTS.
D-LINK SHALL NOT BE LIABLE UNDER THIS WARRANTY IF ITS TESTING
AND EXAMINATION DISCLOSE THAT THE ALLEGED DEFECT IN THE
PRODUCT DOES NOT EXIST OR WAS CAUSED BY TH E CU STOMER'S OR
ANY THIRD PERSON'S MISUSE, NEGL ECT, IMPROPER INSTALLATION OR
TESTING, UNAUTHORIZ ED AT TEMPTS TO REPAIR, OR ANY OTHER CAUSE
BEYOND THE RANGE OF THE INTENDED USE, OR BY ACCIDENT, FIRE,
LIGHTNING OR OTHER HAZARD.

LIMITATION OF LIABILITY

IN NO EVENT WILL D-LINK BE LIABLE FOR ANY DAMAGES, INCLUDING
LOSS OF DATA, LOSS OF PROFITS, COST OF COVER OR OTHER
INCIDENTAL, CONSEQUENT IAL OR INDIRECT DAMAGES ARISING OUT
THE INSTALLATION, MAINTENANCE, USE, PERFORMANCE, FAILURE OR
INTERRUPTION OF A D- LINK PRODUCT, HOWEVER CAUSED AND ON ANY
THEORY OF LIABILITY. THIS LIMITATION WILL APPLY EVEN IF D-LINK
HAS BEEN ADVISED OF THE POSSIBILITY OF SU CH DAMAGE.

IF YOU PURCHASED A D-LINK PRODUCT IN THE UNITED STATES, SOME
STATES DO NOT ALLOW THE LIMITATION OR EXCLUSION OF LIABILITY
FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES, SO THE ABOVE
LIMITATION MAY NOT APPLY TO YOU.

Trademarks

Copyright 1999 D-Link Corporation. Contents subj e c t to change without prior
notice. D-Link is a registered trademark of D-Link Corporation/D-Link Systems,
Inc. All other trademarks belong to their respective proprietors.

Copyright Statement

No part of this publication may be repro duced in any for m or by any me ans or used
to make any derivative such as translation, transformation, or adaptation without
permission from D-Link Corporation/D-Link Systems Inc., as stipulated by the
United States Copyright Act of 1976.

FCC Warning

This equipment has been tested and found to comply with the limits for a Class A
digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference when the equipment is
operated in a commercial environment. This equipment generates, uses, and can
radiate radio frequency energy and, if not installed and used in accordance with
this user’s guide, may cause harmful interference to radio communications.
Operation of this equipment in a residential area is likely to cause harmful
interference in which case the user will be required to correct the interfere nce at
his own expense.

CE Mark Warning

This is a Class A product. In a domestic environment, this product may cause radio
interference in which case the user may be required to take adequate measures.

VCCI Warning

BSMI Warning

T

ABLE OF

0 ABOUT THIS GUIDE......................................................................... IX

C

ONTENTS

URPOSE

P

ERMS/USAGE

T

VERVIEW OF THIS USER’S GUIDE

O

1 INTRODUCTION...................................................................................1

EATURES

F

Performance features................................................................................2

2 UNPACKING AND SETUP...................................................................3

NPACKING

U

ETUP

S

ESKTOP OR SHELF INSTALLATION

D

ACK INSTALLATION

R

OWER ON

P

LED Indicators..........................................................................................7

Power Failure ...........................................................................................7

3 IDENTIFYING EXTERNAL COMPONENTS....................................8

RONT PANEL

F

EAR PANEL

R
LED I

4 CONNECTING THE SWITCH...........................................................11

WITCH TO

S

WITCH TO HUB (WITH UPLINK

S

10BASE-T Hub........................................................................................13

100BASE-TX Hub....................................................................................13

UB WITHOUT UPLINK

H

Using straight cable................................................................................14

Using crossover cable.............................................................................14

......................................................................................................

.............................................................................................

...............................................................

.....................................................................................................1

...................................................................................................3

............................................................................................................4

...............................................................4

.....................................................................................5

.....................................................................................................6

................................................................................................8

.................................................................................................9

NDICATORS

..........................................................................................9

PC.............................................................................................11

)..................................................................12

(MDI-II)

PORT

........................................................13

IX
IX
IX

5 TECHNICAL SPECIFICATIONS......................................................15

6 RJ-45 PIN SPECIFICATION..............................................................18

10/100 NWay Ethernet/Fast Ethernet Switch User’s Guide

0 A

Congratulations on your purchase of the 10/100 NWay
Ethernet/Fast Ethernet Switch. This device integrates 100Mbps
Fast Ethernet and 10Mbps Ethernet network capabilities in a
highly flexible package.

BOUT THIS

G

UIDE

Purpose

The purpose of this manual is to discuss the installation and use of
your 16-port 10/100Mbps NWay Ethernet/Fast Ethernet Switch.

Terms/Usage

For simplicity, this documentation uses the term “Switch” (first
letter upper case) to re fer to the DES-1016D Switch, an d “switch”
(first letter lower case) to refer to all switches, including the DES­1016D.

Overview of this User’s Guide

Chapter 1, “

♦

features.

About This Guide ix

Introduction

.” Describes the Switch and its

10/100 NWay Ethernet/Fast Ethernet Switch User’s Guide

Chapter 2, “

♦

Unpacking and Setup

.” Helps you get started

with the basic installation of the Switch.
Chapter 3, “

♦

Identifying External Components

.” Describes the

front panel, rear panel, and LED indicators of the Switch.
Chapter 4, “

♦

Connecting the Switch

.” Tells how you can

connect the Switch to your Ethernet network.
Appendix A, “

♦

Technical Specifications.”

Lists the technical
(general, physical and environmental, and performance)
specifications of the Switch.

Appendix B, “

♦

RJ-45 Pin Specification.”

Describes the RJ-45
receptacle/connector and the straight and crossover cable
connector.

x About This Guide

10/100 NWay Ethernet/Fast Ethernet Switch User’s Guide

1

1 I

This section describes the features of the Switch.

NTRODUCTION

Features

The Switch is designed for easy installation, a superior
cost/performance ratio, and easy migration to a bandwidth-critical
environment where traffic on the network and the number of users
increases continuously.

The Switch supports auto-nego tiation, allowing both 10Mbps and
100Mbps operation in full- duplex or half- duplex mode, e ven on all
ports simultaneously.

Low price and compact dimensions make the Switch suitable for
small and medium-size workgroups as well as SOHO
environments, enabling users to migrate easily from traditional
shared LANs to switched networks. Each full/half duplex port can
be connected directly to high-demand nodes, such as workstations,
servers, or other switches or hubs, to meet increased bandwidth
and flexibility demands.

The Switch performs store-and-forward switching to ensure
effective buffer allocation for each port. Data flow is controlled
between the transmitting and receiving nodes to guarantee
against all possible packet loss.

Introduction 1

10/100 NWay Ethernet/Fast Ethernet Switch User’s Guide

Performance features

♦ Sixteen high-performance 10/100Mbps NWay ports; all ports

can auto-negotiate for full- or half-duplex operation

♦ Uplink (MDI-II) port for straight-through connection to another

switch, hub or repeater

♦ Full wire-speed forwarding for 100Mbps Fast Ethernet

(148,800 pps) and 10Mbps Ethernet (14,880 pps) on all ports

♦ High-performance 2M SGRAM packet buffer
♦ Up to 8K MAC address table
♦ IEEE 802.3x-compliant flow control for full duplex mode
♦ Back-pressure control for half duplex mode
♦ Store-and-forward packet switching supports rate

adaptation and ensures data integrity

♦ A full complement of LED status indicators

2 Introduction

10/100 NWay Ethernet/Fast Ethernet Switch User’s Guide

2

2 U

This chapter provides unpacking and setup information for the
Switch.

NPACKING AND

S

ETUP

Unpacking

Open the shipping carton of the Switch and carefully unpack its
contents. The carton should contain the following items:

♦ One 10/100 NWay Ethernet/Fast Ethernet Switch
♦ One AC power cord
♦ This User’s Guide
♦ Four rubber feet with adhesive backing

If any item is found missing or damaged, please contact your local
network supplier for replacement.

Unpacking and Setup 3

10/100 NWay Ethernet/Fast Ethernet Switch User’s Guide

Setup

The setup of the Switch can be performed using the following
steps:

♦ The surface must support at least 5kg for the Switch.
♦ The power outlet should be within 1.82 meters (6 feet) of the

device.

♦ Visually inspect the power cord and see that it is fully

secured to the AC power connector.

♦ Make sure that there is proper heat dissipation from and

adequate ventilation around the Switch. Do not place heavy
objects on the Switch.

Desktop or Shelf Installation

When installing the Switch on a desktop or shelf, the rubber feet
included with the device must be first attached. Attach these
cushioning feet on the bottom at each corner of the device. Allow
enough ventilation space between the device and the objects
around it.

4 Unpacking and Setup

10/100 NWay Ethernet/Fast Ethernet Switch User’s Guide

Figure 2.1 10/100 NWay Ethernet/Fast Ethernet Switch installed

on a Desktop or Shelf

Rack Installation

The Switch can be mounted in an EIA standard size, 19-inch rack,
which can be placed in a wiring closet with other equipment. For
information about the DFE-700B Rack Mo untin g Bracke ts, co nsult
your computer hardware dealer. If you already possess the
brackets, attach them on the Switch’s front panel (one on each
side), and then secure them with the provided screws. Then, use
these screws provided with the equipment rack to mount each
Switch in the rack. Follow the directions provided by the rack
manufacturer.

Unpacking and Setup 5

10/100 NWay Ethernet/Fast Ethernet Switch User’s Guide

Figure 2.2 Installing the 10/100 NWay Ethernet/Fast Ethernet

Switch in an equipment rack

Power on

The Switch can be used with AC power sources 100 - 240 VAC, 50 ­60 Hz. The power switch is located at the rear of the unit adjacent
to the AC power connector. To turn the Switch on, press the power
switch to the on or “1” position. The Switch’s power supply will
adjust to the local power source automatically and may be turned
on without having any or all LAN segment cables connected.

6 Unpacking and Setup

10/100 NWay Ethernet/Fast Ethernet Switch User’s Guide

LED Indicators

After the switch is turned on, the LED indicators should respond
as follows:

♦ All of the LED indicators will blink momentarily. This

blinking of the LED indicators represents a reset of the
system.

♦ The power LED indicator will remain ON.

Power Failure

As a precaution, the Switch should be turned OFF in case of a
power failure. Press the power switch to the off or “0” position.
When power is resumed, turn the Switch ON. At all times, avoid
leaving the Switch ON if a power failure is anticipated.

Unpacking and Setup 7

10/100 NWay Ethernet/Fast Ethernet Switch User’s Guide

3

3 I

This chapter describes the front panel, rear panel, and LED
indicators of the Switch.

DENTIFYING

E

XTERNAL

C

OMPONENTS

Front Panel

The front panel of the Switch consists of sixteen (10/100 Mbps
MDI-X) ports, one uplink (MDI-II) port, and LED indicators. A
description of the ports appears in the Introduction of this User’s
Guide (see Features, Chapter 1).

Figure 3.1 Front panel view of the 10/100 NWay Ethernet/Fast

Ethernet Switch

8 Identifying External Components

10/100 NWay Ethernet/Fast Ethernet Switch User’s Guide

Rear Panel

The rear panel of the device consists of an AC power connector and
a power switch.

Figure 3.2 Rear panel view of the 10/100 NWay Ethernet/Fast

Ethernet Switch

♦ AC Power Connector This is a three-pronged connector

that supports the power cord. Plug in the female connector
of the provided power cord into this connector, and the male
into a power outlet. Supported input voltages range from
100 ~ 240 VAC at 50 ~ 60 Hz.

♦ Power Switch This turns the Switch on and off. To turn on

the system, press the switch to the “1” position; to turn off ,
press the switch to the “0” position.

LED Indicators

The LED indicators of the Switch include Power,
100Mbps/10Mbps, and Link/Act (Link/Activity). The LED
indicators are used to facilitate monitoring and troubleshooting of
the Switch. The following shows the LED indicators for the Switch
along with an explanation of each indicator.

Identifying External Components 9

10/100 NWay Ethernet/Fast Ethernet Switch User’s Guide

Figure 3.3 The 10/100 NWay Ethernet/Fast Ethernet Switch LED

indicators

♦ Power This indicator operates when the Switch is turned

on. If this indicator is not lit, check the AC power connector
to ensure proper insertion of the power cord and that the
power switch is turned ON.

♦ 100Mbps/10Mbps The LED indicator lights when a 100

Mbps device is connected to a respective port or the uplink
port. If a 10 Mbps device is connected to a respective port or
the uplink port, the LED indicator is OFF.

♦ Link/Act These LED indicators are lit when there is a

secure connection (or link) to a device at any of the ports.
They remain dark if there is no link. The LED indicators
blink whenever there is reception or transmission (i.e.
Activity—Act) of data occurring at a port.

10 Identifying External Components

10/100 NWay Ethernet/Fast Ethernet Switch User’s Guide

4

4 C

This chapter describes how to connect the 10/100 NWay
Ethernet/Fast Ethernet Switch to your Fast Ethernet network.

ONNECTING THE

S

WITCH

Switch to PC

A PC can be connected to the Switch via a two-pair Category 3, 4,
5 UTP/STP straight cable (Cat. 3, 4, and 5 for 10M and Cat. 5 for
100M). The PC (equipped with a RJ-45 10/100 Mbps jack) should
be connected to any of the sixteen ports (1x -16x).

Figure 4.1 10/100 NWay Ethernet/Fast Ethernet Switch connected

to a PC or Workstation

Connecting The Switch 11

10/100 NWay Ethernet/Fast Ethernet Switch User’s Guide

The LED indicators for PC connection are dependent on the LAN
card capabilities. If LED indicators are not illuminated after
making a proper connection, check the PC’s LAN card, the cable,
Switch conditions, and connections.

The following are LED indicator possibilities for a PC to Switch
connection:

1. The 100Mbps LED indicator comes on for a 100 Mbps

connection and stays off for 10 Mbps connection.

2. The Link/Act LED indicator illuminates upon hookup.

Switch to Hub (with Uplink)

A hub (10 or 100BASE-TX) can be connecte d to the Switch via a
two-pair Category 3, 4, 5 UTP/STP straight cable. The con nection
is accomplished from the hub’s Uplink (MDI- II) port to any of the
Switch’s (MDI-X) ports.

Figure 4.2 10/100 NWay Ethernet/Fast Ethernet Switch connected

to a 10BASE-T or 100BASE-TX Hub

12 Connecting The Switch

10/100 NWay Ethernet/Fast Ethernet Switch User’s Guide

10BASE-T Hub

For a 10BASE-T hub, the Switch’s LED indicators should
illuminate the following:

♦ 100Mbps LED speed indicator is OFF.
♦ Link/Act indicator is ON.

100BASE-TX Hub

For a 100BASE-TX hub, the Switch’s LED indicators should
illuminate the following:

♦ 100Mbps LED speed indicator is ON.
♦ Link/Act is ON.

Hub without Uplink (MDI-II) port

If a hub is not equipped with an Uplink (MDI-II) port, then a
connection can be made using either straight cable or crossover
cable (see Appendix B, Pin Specificat ion for cable requirement).

Connecting The Switch 13

10/100 NWay Ethernet/Fast Ethernet Switch User’s Guide

Figure 4.3 10/100 NWay Ethernet/Fast Ethernet Switch connected to

a Hub without Uplink (MDI-II) port using the straight or crossover

cable option

Using straight cable

When using straight cable, the connection can be made from the
Uplink (MDI-II) port of the Switch to any port of the Hub.

Using crossover cable

When using crossover cable, the connection can be made from any
MDI-X ports of the Switch to any port of the Hub.

14 Connecting The Switch

10/100 NWay Ethernet/Fast Ethernet Switch User’s Guide

A

5 T

S

PECIFICATIONS

General

Standards: IEEE 802.3 10BASE-T Ethernet

IEEE 802.3u 100 BASE-TX Fast Ethernet
ANSI/IEEE std. 802.3 NWay auto-negotiation

Protocol: CSMA/CD Ethernet

Data Transfer Rate: Ethernet: Fast Ethernet:

10 Mbps (half duplex) 100Mbps (half duplex)
20 Mbps (full duplex) 200Mbps (full duplex)

Topology: Star

Network Cabling:

10BASE-T:

2-pair UTP Cat. 3,4,5 (100 m)

ECHNICAL

EIA/TIA- 568 100-ohm STP (100 m)

100BASE-TX:

2-pair UTP Cat. 5 (100 m)
EIA/TIA-568 100-ohm STP (100 m)

Technical Specifications 15

10/100 NWay Ethernet/Fast Ethernet Switch User’s Guide

General

Number of Por ts: 16 x 10BASE-T/100BASE-TX ports

Media Interface
Exchange:

1 x MDI-II RJ-45 shared with port 1

Physical and Environmental

AC inputs: 100 – 240 VAC, 50/60 Hz

Power Consumption: 24 watts maximum

Operating
Temperature:

Storage
Temperature:

Humidity: 5% ~ 95% non-condensing

Dimensions: 324 x 231 x 44.5 mm (W x D x H)

Weight: 2.6 kg

EMI: FCC Class A, VCCI Class A, BSMI Class A, CE Mark Class

Safety: UL, CUL

0 ° ~ 55 °C

-25 ° ~ 55 °C

A, C-Tick Class A

Performance

Transmission Methods: Store-and-forward

RAM Buffer: 2M SGRAM per device

16 Technical Specifications

10/100 NWay Ethernet/Fast Ethernet Switch User’s Guide

Packet Filtering/Forwarding
Rate:

MAC Address Learning : Up to 8K MAC address table

14,880 pps per port (for 10Mbps)
148,800 pps per port (for 100Mbps)

Technical Specifications 17

10/100 NWay Ethernet/Fast Ethernet Switch User’s Guide

B

6 RJ-45 P

S

PECIFICATION

When connecting the 10/100 NWay Eth ernet/Fast Eth ernet Sw itch
to another switch, a bridge or a hub, a modified crossover cable is
necessary. Please review these products for matching cable pin
assignment.

The following diagram and tables show the standard RJ-45
receptacle/connector and their pin assignments for the switch-to­network adapter card connection, and the straight/crossover cable
for the Switch-to-switch/hub/bridge connection.

IN

The standard RJ-45 receptacle/connector

18 RJ-45 Pin Specification

10/100 NWay Ethernet/Fast Ethernet Switch User’s Guide

RJ-45 Connector pin assignment

Contact Media Direct Interface Signal

1 Tx + (transmit)
2 Tx - (transmit)
3 Rx + (receive)
4 Not used
5 Not used
6 Rx - (receive)
7 Not used
8 Not used

The standard Category 3 cable, RJ-45 pin assignment

The following shows straight cable and crossover cable connection:

Straight cable for Switch (Uplink MDI-II port) to switch/Hub or

other devices connection

Crossover cable for Switch (MDI-X port) to switch/hub or other

network devices (MDI-X port) connection

RJ-45 Pin Specification 19

Offices

AUSTRALIA D-LINK AUSTRALIA PTY.LTD.

CANADA D-LINK CANADA, INC.

CHINA D-LINK BEIJING

DENMARK D-LINK DENMARK

FRANCE D-LINK FRANCE

GERMANY D-LINK (DEUTSCHLAND) GMBH I.G.

INDIA D-LINK (INDIA) PVT. LTD.

JAPAN D-LINK TOKYO

SINGAPORE D-LINK SINGAPORE PTE. LTD.

SWEDEN D-LINK A/B SWEDEN

TAIWAN D-LINK TAIWAN

U.K. D-LINK (EUROPE) LTD.

U.S.A. D-LINK SYSTEMS, INC.

Unit 16, 390 Eastern Valley Way Roseville, NSW 2069 Sydney Australia
TEL: [phone] FAX: [phone] T OLL FREE: 180017710 WEB: www.dlink.com.au
E-MAIL: [e-mail] m.au

2180 Winston Park Drive, Oakville, Ontario L6H 5W1 Can ada
TEL: [phone] FAX: [phone]
WEB: www.dlinknet.com FTP: ftp.dlinknet.com E-MAIL: [e-mail]

15th Floor, Science & Technology Tower,
No. 11, Baishiqiao Road, Haidian D istrict, Beijing 100081 China
TEL: [phone] FAX: [phone] WEB: www.dlink.co.cn

Naverland 2 DK-2600 Glo strup Copenhagen, Denmark
TEL:[phone] FAX:[phone]

Le FLORILEGE #2, Allee de la Fresnerie
78330 Fontenay Le Fleury France
TEL: [phone] FAX: [phone] WEB: www.dlink-france.com

Bachstrae 22, D/65830 Kr if te l Germany
TEL: [phone] FAX: [phone] WEB: www.dlink.de BBS: 49-6192-971199
INFO: 0130-7250-00 (toll free) H EL P : 0130-7250-40 (toll free)

Plot No.5, Kurla-Bandra Complex Rd.
Off Cst Rd., Santacru z ( E) , Bombay - 400 098 India
TEL: [phone] FAX: [phone]

10F, 8-8-15 Nishigotanda, Shinagawa-ku, Tok yo 141 Japan
TEL: [phone] FAX: [phone] WEB: www.d-link.co.jp

1 International Business P ark, #03-12 The Syner gy, Singapore 609917
TEL : [phone] FAX: [phone] E-M AIL : [e-mail]. sg

World Trade Centre P. O. Box 70396, 107 24 Stockh o l m Sweden
TEL: [phone] FAX: [phone] E- MAIL: [e-mail]

2F, No. 233-2 Pao-Chiao Rd, Hsin- T ie n, Taipei, Taiwan, R.O.C.
TEL: [phone] FAX: [phone] WEB: www.dlink.com.tw

D-Link House, 6 Garland Road, Stanmore, Middlesex HA7 1DP U.K.
TEL: [phone] FAX: [phone] WEB: www.dlink.co.uk
E-MAIL: [e-mail]. uk

53 Discovery Dr ive, Irvine, CA 92618 USA
TEL: [phone] FAX: [phone] WEB: www.dlink.com E-MAIL: [e-mail]

Registration Card

Print, type or use block letters.

Your name: Mr./Ms_____________________________________________________________________________
Organization: ________________________________________________Dept. ____________________________
Your title at organization:________________________________________________________________________
Telephone:_______________________________________ Fax:________________________________________
Organization's full address: ______________________________________________________________________

____________________________________________________________________________________________
Country: _____________________________________________________________________________________
Date of purchase (Month/Day/Year):_______________________________________________________________

Product Model Product Serial

No.

(* Applies to adapters only)

Product was purchased f rom:

Reseller's name: ______________________________________________________________________________
Telephone:_______________________________________ Fax:________________________________________
Reseller's full address: _________________________________________________________________________

_________________________________________________________________________
_________________________________________________________________________

Answers to the following questions help us to support your product:

1.Where and how will the product primarily be used?

Home !Office !Travel !Company Business !Home Business !Personal Use

!

2. How many employees work at installation site?

1 employee !2-9 !10-49 !50-99 !100-499 !500-999 !1000 or more

!

3. What network protocol(s) does your organization use ?

XNS/IPX !TCP/IP !DECnet !Others_____________________________

!

4. What network operating system(s) does your organization use ?

D-Link LANsmart !Novell NetWa re !NetWare Lite !SCO Unix/Xenix !PC NFS !3Com 3+Open

!

Banyan Vines !DECnet Pathwork !Windows NT !Windows NTAS !Windows '95

!

Others__________________________________________

!

5. What network management program does your organization use ?

D-View !HP OpenView/Windows !HP OpenView/Unix !SunNet Manager !Novell NMS

!

NetView 6000 !Others________________________________________

!

6. What network medium/media does your organization use ?

Fiber-optics !Thick coax Ethernet !Thin coax Ethernet !10BASE-T UTP/STP

!

100BASE-TX !100BASE-T4 !100VGAnyLAN !Others_________________

!

7. What applications are used on your network?

Desktop publishing !Spreadsheet !Word processing !CAD/CAM

!

Database management !Accounting !Others_____________________

!

8. What category best describes your company?

Aerospace !Engineering !Education !Finance !Hospital !Legal !Insurance/Real Estate !Manufacturing

!

Retail/Chainstore/Wholesal e !Government !Transportation/Utilities/Communication !VAR

!

System house/company !Other________________________________

!

9. Would you recommend your D-Link product to a friend?

Yes !No !Don't know yet

!

10.Your comments on this product?

__________________________________________________________________________________________
__________________________________________________________________________________________

* Product installed in type of
computer (e.g., Compaq 486)

* Product installed in

computer serial No.