The symbols shown above are internationally accepted symbols that warn
of potential hazards with electrical products. The lightning flash with
arrowpoint in an equilateral triangle means that there are dangerous
voltages present within the unit. The exclamation point in an equilateral
triangle indicates that it is necessary for the user to refer to the owner’s
manual.
These symbols warn that there are no user serviceable parts inside the
unit. Do not open the unit. Do not attempt to service the unit yourself.
Refer all servicing to qualified personnel. Opening the chassis for any
reason will void the manufacturer’s warranty. Do not get the unit wet. If
liquid is spilled on the unit, shut it off immediately and take it to a dealer
for service. Disconnect the unit during storms to prevent damage.
The following is indicative of low
altitude use; do not use this product
above 2000m.
U.K. MAINS PLUG WARNING
A molded mains plug that has been cut off from the cord is unsafe.
Discard the mains plug at a suitable disposal facility.
FOLLOW ALL INSTRUCTIONS.
DO NOT USE THIS APPARATUS NEAR WATER.
CLEAN ONLY WITH A DRY CLOTH.
FOR INDOOR USE ONLY.
DO NOT BLOCK ANY OF THE VENTILATION OPENINGS. INSTALL IN ACCORDANCE WITH THE
MANUFACTURER’S INSTRUCTIONS.
DO NOT INSTALL NEAR ANY HEAT SOURCES SUCH AS RADIATORS, HEAT REGISTERS, STOVES, OR
OTHER APPARATUS (INCLUDING AMPLIFIERS) THAT PRODUCE HEAT.
ONLY USE ATTACHMENTS/ACCESSORIES SPECIFIED BY THE MANUFACTURER.
UNPLUG THIS APPARATUS DURING LIGHTNING STORMS OR WHEN UNUSED FOR LONG PERIODS
OF TIME.
Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two
blades with one wider than the other. A grounding type plug has two blades and a third grounding
prong. The wide blade or third prong are provided for your safety. If the provided plug does not fit
your outlet, consult an electrician for replacement of the obsolete outlet.
Protect the power cord from being walked on or pinched particularly at plugs, convenience
receptacles, and the point where they exit from the apparatus.
NEVER UNDER ANY CIRCUMSTANCES SHOULD YOU INSERT A DAMAGED OR CUT MAINS PLUG INTO A 13 AMP
POWER SOCKET.
Do not use the mains plug without the fuse cover in place. Replacement
fuse covers can be obtained from your local retailer. Replacement fuses
are 13 amps and MUST be ASTA approved to BS1362.
If you want to dispose this product, do not mix it with general household waste. There is a separate collection system
for used electronic products in accordance with legislation that requires proper treatment, recovery and recycling.
Private households in the 25 member states of the EU, in Switzerland and Norway may return their used electronic products free
of charge to designated collection facilities or to a retailer (if you purchase a similar new one).
For Countries not mentioned above, please contact your local authorities for a correct method of disposal.
By doing so you will ensure that your disposed product undergoes the necessary treatment, recovery and recycling and thus prevent
potential negative effects on the environment and human health.
Use only with the cart stand, tripod bracket, or table specified by the
manufacture, or sold with the apparatus. When a cart is used, use caution
when moving the cart/apparatus combination to avoid injury from tip-over.
Refer all servicing to qualified service personnel. Servicing is required when the apparatus has
been damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled
or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does
not operate normally, or has been dropped.
POWER ON/OFF SWITCH: The Power switch used in this piece of equipment DOES NOT break the
connection from the mains.
MAINS DISCONNECT: The plug shall remain readily operable. For rack-mount or installation where
plug is not accessible, an all-pole mains switch with a contact separation of at least 3 mm in each
pole shall be incorporated into the electrical installation of the rack or building.
If connected to 240V supply, a suitable CSA/UL certified power cord shall be used for this supply.
IMPORTANT SAFETY INSTRUCTIONS
ELECTROMAGNETIC COMPATIBILITY
This device complies with part 15 of the FCC Rules and the Product
Specifications noted on the Declaration of Conformity. Operation
is subject to the following two conditions:
• this device may not cause harmful interference, and
• this device must accept any interference received, including
interference that may cause undesired operation.
Operation of this unit within significant electromagnetic fields should be
avoided.
• use only shielded interconnecting cables.
SAFETY INSTRUCTIONS
NOTICE FOR CUSTOMERS IF YOUR UNIT IS EQUIPPED WITH A POWER CORD.
WARNING: THIS APPLIANCE SHALL BE CONNECTED TO A MAINS SOCKET OUTLET WITH A PROTECTIVE
EARTHING CONNECTION.
THE CORES IN THE MAINS LEAD ARE COLOURED IN ACCORDANCE WITH THE FOLLOWING CODE:
GREEN AND YELLOW - EARTH BLUE - NEUTRAL BROWN - LIVE
DECLARATION OF CONFORMITY
Manufacturer’s Name: DigiTech
Manufacturer’s Address: 10653 South River Front Parkway, #300
South Jordan, Utah 84095, USA
declares that the product:
Product name: JamMan Vocal XT
Product option: all (requires Class II power adapter that
conforms to the requirements of EN60065,
EN60742, or equivalent).
conforms to the following Product Specifications:
Safety: IEC 60065 -01+Amd 2
EMC: EN 55022:2006
EN 55024:1998
FCC Part 15
Supplementary Information:
AS COLOURS OF THE CORES IN THE MAINS LEAD OF THIS APPLIANCE MAY NOT CORRESPOND WITH THE
COLOURED MARKINGS IDENTIFYING THE TERMINALS IN YOUR PLUG, PROCEED AS FOLLOWS:
• THE CORE WHICH IS COLOURED GREEN AND YELLOW MUST BE CONNECTED TO THE TERMINAL IN
THE PLUG MARKED WITH THE LETTER E, OR WITH THE EARTH SYMBOL, OR COLOURED GREEN, OR
GREEN AND YELLOW.
• THE CORE WHICH IS COLOURED BLUE MUST BE CONNECTED TO THE TERMINAL MARKED N OR
COLOURED BLACK.
• THE CORE WHICH IS COLOURED BROWN MUST BE CONNECTED TO THE TERMINAL MARKED L OR
COLOURED RED.
THIS EQUIPMENT MAY REQUIRE THE USE OF A DIFFERENT LINE CORD, ATTACHMENT PLUG, OR BOTH,
DEPENDING ON THE AVAILABLE POWER SOURCE AT INSTALLATION. IF THE ATTACHMENT PLUG NEEDS TO
BE CHANGED, REFER SERVICING TO QUALIFIED SERVICE PERSONNEL WHO SHOULD REFER TO THE TABLE
BELOW. THE GREEN/YELLOW WIRE SHALL BE CONNECTED DIRECTLY TO THE UNITS CHASSIS.
CONDUCTOR
LLIVEBROWNBLACK
NNEUTRALBLUEWHITE
EEARTH GNDGREEN/YELGREEN
WARNING: IF THE GROUND IS DEFEATED, CERTAIN FAULT CONDITIONS IN THE UNIT OR IN THE SYSTEM TO WHICH IT IS CONNECTED CAN RESULT IN FULL LINE VOLTAGE BETWEEN CHASSIS AND EARTH
GROUND. SEVERE INJURY OR DEATH CAN THEN RESULT IF THE CHASSIS AND EARTH GROUND ARE
TOUCHED SIMULTANEOUSLY.
WIRE COLOR
NormalAlt
The product herewith complies with the requirements of the:
Low Voltage Directive 2006/95/EC
EMC Directive 2004/108/EC.
RoHS Directive 2011/65/EC
WEEE Directive 2002/96/EC
EC Regulation 278/2009
With regard to Directive 2005/32/EC and EC Regulation 1275/2008 of
17 December 2008, this product is designed, produced, and classified as
Professional Audio Equipment and thus is exempt from this Directive.
Rex C. Reed
Director, Engineering
Signal Processing
10653 South River Front Parkway, #300
South Jordan, Utah 84095, USA
Date: June 3, 2014
European Contact: Your local DigiTech Sales and Service Office or
Harman Signal Processing
10653 South River Front Parkway, #300
South Jordan, Utah 84095, USA
Ph: (801) 566-8800
Fax: (801) 568-7583
CONSIGNES DE SÉCURITÉ IMPORTANTES
AVERTISSEMENT POUR VOTRE SÉCURITÉ
LIRE ATTENTIVEMENT:
LIRE CES CONSIGNES.
CONSERVER CES CONSIGNES.
RESPECTER TOUS LES AVERTISSEMENTS.
SUIVRE TOUTES LES CONSIGNES.
Les symboles illustrés ci-dessus sont des symboles acceptés
internationalement qui avertissent des dangers potentiels relatifs à
l’utilisation de produits électriques. Le voyant clignotant avec une flèche
dans un triangle équilatéral signifie la présence de tensions dangereuses
dans l'appareil. Le point d’exclamation dans un triangle équilatéral
indique que l’utilisateur doit se référer au manuel d'utilisation.
Ces symboles indiquent qu’il n’y a aucune pièce utilisable par l’utilisateur
à l’intérieur de l’appareil. Ne pas ouvrir l’appareil. Ne pas essayer de
réparer soi-même l’appareil. Confier toute réparation à du personnel
qualifié. Ouvrir la structure de l’appareil pour quelque raison que ce soit
annulera la garantie du fabricant. Ne pas mouiller l’appareil. Si du liquide
est renversé sur l’appareil, fermer immédiatement l’appareil et l’apporter
chez un réparateur. Débrancher l’appareil pendant les tempêtes afin
d’éviter des dommages.
Ce qui suit est représentatif d’une
utilisation à basse altitude ; ne pas
utiliser ce produit au-dessus de 2000 m.
AVERTISSEMENT CONCERNANT LA FICHE SECTEUR
Une fiche secteur moulée qui a été coupée du cordon est dangereuse.
Jeter la fiche secteur dans un centre de déchets adapté.
VOUS NE DEVEZ EN AUCUNE CIRCONSTANCE INSÉRER
UNE FICHE ENDOMMAGÉE OU COUPÉE DANS UNE PRISE
SECTEUR 13 AMP.
Ne pas utiliser la fiche secteur si le couvercle du coffret à fusibles n'est
pas bien en place. Vous pouvez vous procurer des capots de fusible de
rechange auprès de votre détaillant local. Les fusibles de remplacement
sont de 13 A et DOIVENT être approuvés ASTA, BS1362.
Ne pas jeter ce produit avec les ordures ménagères. Il existe un système de collecte sélective pour les produits
électroniques usagés en conformité avec les lois en vigueur en matière de traitement, de récupération et de recyclage.
Dans les 25 États membres de l'UE, en Norvège et en Suisse, les ménages peuvent envoyer leurs produits électroniques
usagés sans frais vers des centres de collecte sélective ou chez un distributeur (contre l'achat d'un nouveau produit).
Contacter les autorités locales pour connaître les procédures de traitement des déchets adaptées dans les pays non
mentionnés ci-dessus.
Non seulement cette précaution vous permettra d’être sûr que votre produit est correctement traité, récupéré et recyclé,
mais elle vous évitera également de nuire involontairement à l'environnement et à la santé humaine.
NE PAS UTILISER CET APPAREIL PRÈS DE L’EAU.
NETTOYER UNIQUEMENT AVEC UN CHIFFON SEC.
POUR USAGE INTÉRIEUR UNIQUEMENT.
NE PAS OBSTRUER LES OUÏES D’AÉRATION. EFFECTUER L’INSTALLATION CONFORMÉMENT AUX
INSTRUCTIONS DU FABRICANT.
NE PAS INSTALLER À PROXIMITÉ DE SOURCES DE CHALEUR TELLES QUE DES RADIATEURS,
BOUCHES D’AÉRATION, PLAQUES CHAUFFANTES OU TOUT AUTRE APPAREIL (Y COMPRIS DES
AMPLIFICATEURS) DÉGAGEANT DE LA CHALEUR.
UTILISER UNIQUEMENT LES PIÈCES/ACCESSOIRES MENTIONNÉS PAR LE FABRICANT.
DÉBRANCHER L'APPAREIL AU COURS DES ORAGES OU EN CAS DE NON-UTILISATION PENDANT UNE
DURÉE PROLONGÉE.
Ne pas détériorer la sécurité de la fiche polarisée ou de la fiche de terre. Les fiches polarisées sont
équipées de deux bornes de largeurs différentes. Les fiches de terre comportent deux lames et une
troisième broche de mise à la terre. La broche la plus large ou troisième broche de mise à la terre
est prévue pour votre sécurité. Si la fiche fournie ne correspond pas à votre installation électrique,
faire appel à un électricien pour remplacer la prise hors normes.
Protéger le cordon d'alimentation contre les risques de piétinement ou de pincement, notamment
au niveau des fiches, des prises de courant et du point d'attache avec le matériel.
Utiliser uniquement le chariot, le support, le trépied ou la table spécifié(e)
par le fabricant ou vendu(e) avec le matériel. Si vous utilisez un chariot
pour déplacer l'appareil, soyez suffisamment prudent pour éviter une
éventuelle blessure consécutive au basculement du chariot et de sa charge.
Les réparations doivent être confiées à un technicien S.A.V. qualifié. Une réparation est nécessaire en
cas de dommage quelconque et en particulier en cas d'endommagement du cordon d’alimentation
ou de la fiche électrique, d'infiltration liquide, d'introduction involontaire d'un objet dans l'appareil,
d'exposition de l’appareil à la pluie ou à un milieu humide, de fonctionnement anormal ou de chute
de l'appareil.
INTERRUPTEUR MARCHE/ARRÊT : l'interrupteur d'alimentation de cet équipement NE coupe PAS
la connexion secteur.
DÉBRANCHEMENT DE L'APPAREIL : la prise de courant doit rester facilement accessible. Pour un
montage en rack ou une installation avec une prise inaccessible, un interrupteur omnipolaire à
distance d'ouverture de contact d'au moins 3 mm doit être intégré à l’installation électrique du
rack ou du local.
Si le matériel est relié à une alimentation de 240 V, utiliser impérativement un cordon d'alimentation
adapté certifié CSA/UL pour ce branchement.
CONSIGNES DE SÉCURITÉ IMPORTANTES
COMPATIBILITÉ ÉLECTROMAGNÉTIQUE
Cet appareil est conforme au volet 15 des règles du FCC et aux
spécifications techniques évoquées dans la Déclaration de conformité. Son fonctionnement est soumis aux deux conditions
suivantes :
• cet appareil ne doit pas causer d’interférences nuisibles et
• cet appareil doit accepter les interférences captées, y compris les
interférences susceptibles de nuire à son fonctionnement.
L’utilisation de cet appareil à proximité de champs électromagnétiques
puissants n’est pas recommandée.
• utiliser exclusivement des câbles d’interconnexion blindés.
CONSIGNES DE SÉCURITÉ
NOTICE ADRESSÉE AUX CONSOMMATEURS ÉQUIPÉS D’UN MATÉRIEL AVEC CORDON D’ALIMENTATION
FOURNI.
AVERTISSEMENT : CET APPAREIL DOIT ÊTRE BRANCHÉ SUR UNE PRISE SECTEUR DOTÉE D'UNE PROTECTION PAR MISE À LA TERRE.
LES COULEURS DES NOYAUX DANS LES FILS SECTEURS DOIVENT RESPECTER LES CODES SUIVANTS :
VERT ET JAUNE - TERRE BLEU - NEUTRE MARRON - PHASE
LES COULEURS DES NOYAUX DANS LES FILS SECTEURS DE CET APPAREIL PEUVENT NE PAS CORRESPONDRE AUX INSCRIPTIONS COLORÉES IDENTIFIANT LES TERMINAUX DANS VOTRE FICHE ; IL FAUT DONC
PROCÉDER DE LA FAÇON SUIVANTE :
• LE NOYAU VERT ET JAUNE DOIT ÊTRE BRANCHÉ AU TERMINAL DE LA FICHE OÙ APPARAÎT LA LETTRE E
OU LE SYMBOLE DE MISE À LA TERRE, OU AU TERMINAL VERT OU VERT ET JAUNE.
• LE NOYAU BLEU DOIT ÊTRE BRANCHÉ AU TERMINAL MARQUÉ D’UN N OU DE COULEUR NOIRE.
• LE NOYAU MARRON DOIT ÊTRE BRANCHÉ AU TERMINAL MARQUÉ D’UN L OU DE COULEUR ROUGE.
CE MATÉRIEL PEUT NÉCESSITER L’UTILISATION D’UN CORDON D’ALIMENTATION DIFFÉRENT ET/OU
D’UNE FICHE DE BRANCHEMENT DIFFÉRENTE SELON LA SOURCE D’ALIMENTATION DISPONIBLE À
L’INSTALLATION. SI LA FICHE DE BRANCHEMENT DOIT ÊTRE CHANGÉE, FAIRE APPEL À UN TECHNICIEN
QUALIFIÉ QUI DEVRA SE RÉFÉRER AU TABLEAU CI-DESSOUS. LE FIL VERT/JAUNE DOIT ÊTRE BRANCHÉ
DIRECTEMENT AU CHÂSSIS DE L'APPAREIL.
CONNECTEURS
LPHASEMARRONNOIR
NNEUTREBLEUBLANC
ETERREVERT/JAUVERT
ATTENTION : UN DÉFAUT DE MISE À LA TERRE PEUT PROVOQUER CERTAINS DYSFONCTIONNEMENTS
DE L'APPAREIL OU DU SYSTÈME AUQUEL IL EST RELIÉ, POUVANT SE TRADUIRE PAR UNE TENSION COMPOSÉE ENTRE LA MASSE ET LA PRISE DE TERRE. CELA PEUT PROVOQUER DES BLESSURES SÉRIEUSES OU
FATALES SI LA MASSE ET LA PRISE DE TERRE SONT TOUCHÉES EN MÊME TEMPS.
COULEUR DU FIL
normalAlt
DÉCLARATION DE CONFORMITÉ
Nom du fabricant : DigiTech
Adresse du fabricant : 10653 South River Front Parkway, Suite
300 South Jordan, Utah 84095, ÉTATS-UNIS
déclare que le produit :
Nom du produit : JamMan Vocal XT
Option du produit : tous (nécessite un adaptateur secteur de
Classe II conforme aux normes EN60065,
EN60742 ou équivalent).
est conforme aux spécifications suivantes :
Sécurité : CEI/IEC 60065:2001 + Amd 2
CEM : EN 55022:2006
EN 55024:1998
Partie 15 des FCC
Informations complémentaires :
Ce produit est conforme aux exigences suivantes :
Directive sur la basse tension 2006/95/CE
Directive 2004/108/CE.
Directive RoHS 2011/65/UE
Directive DEEE 2002/96/CE
Règlement CE 278/2009
Ce produit appartenant à la catégorie Matériel audio professionnel, il n’est
pas concerné par la directive 2005/32/CE ou par le règlement européen
1275/2008 du 17 décembre 2008.
Rex C. Reed
Directeur, Ingénierie
Traitement des signaux
10653 South River Front Parkway Suite 300
South Jordan, Utah 84095, ÉTATS-UNIS
Date : 3 juin 2014
Contact en Europe : votre revendeur DigiTech local et le bureau d’assistance de :
Harman Signal Processing
10653 South River Front Parkway Suite 300
South Jordan, Utah 84095, ÉTATS-UNIS
Tél. : (801) 566-8800
Fax : (801) 568-7583
Warranty
We at DigiTech® are very proud of our products and back-up each one we sell with the following warranty:
1. Please register online at digitech.com within ten days of purchase to validate this warranty. This warranty is valid only in
the United States.
2. DigiTech warrants this product, when purchased new from an authorized U.S. DigiTech dealer and used solely within the
U.S., to be free from defects in materials and workmanship under normal use and service. This warranty is valid to the
original purchaser only and is non-transferable.
3. DigiTech liability under this warranty is limited to repairing or replacing defective materials that show evidence of defect,
provided the product is returned to DigiTech WITH RETURN AUTHORIZATION, where all parts and labor will be covered up
to a period of one year (this warranty is extended to a period of six years when the product has been properly registered
through our website). A Return Authorization number may be obtained from DigiTech by telephone. The company shall not
be liable for any consequential damage as a result of the product’s use in any circuit or assembly.
4. Proof-of-purchase is considered to be the responsibility of the consumer. A copy of the original purchase receipt must be
provided for any warranty service.
5. DigiTech reserves the right to make changes in design, or make additions to, or improvements upon this product without
incurring any obligation to install the same on products previously manufactured.
6. The consumer forfeits the benefits of this warranty if the product’s main assembly is opened and tampered with by anyone
other than a certified DigiTech technician or, if the product is used with AC voltages outside of the range suggested by
the manufacturer.
7. The foregoing is in lieu of all other warranties, expressed or implied, and DigiTech neither assumes nor authorizes any
person to assume any obligation or liability in connection with the sale of this product. In no event shall DigiTech or its
dealers be liable for special or consequential damages or from any delay in the performance of this warranty due to causes
beyond their control.
NOTE: The information contained in this manual is subject to change at any time without notification. Some information
contained in this manual may also be inaccurate due to undocumented changes in the product since this version of the manual
was completed. The information contained in this version of the owner’s manual supersedes all previous versions.
Service Contact Info
If you require technical support, contact DigiTech Technical Support. Be prepared to accurately describe the problem. Know the
serial number of your device - this is printed on a sticker attached to the chassis. If you have not already taken the time to
register your product, please do so now at digitech.com.
Before you return a product to the factory for service, we recommend you refer to the manual. Make sure you have correctly
followed installation steps and operation procedures. For further technical assistance or service, please visit our support page
at digitech.com/en-US/support. If you need to return a product to the factory for service, you MUST first contact Technical
Support to obtain a Return Authorization Number.
No returned products will be accepted at the factory without a Return Authorization Number.
Please refer to the Warranty information, which extends to the first end-user. After expiration of the warranty, a reasonable
charge will be made for parts, labor, and packing if you choose to use the factory service facility. In all cases, you are
responsible for transportation charges to the factory. DigiTech will pay return shipping if the unit is still under warranty.
Use the original packing material if it is available. Mark the package with the name of the shipper and with these words in
red: DELICATE INSTRUMENT, FRAGILE! Insure the package properly. Ship prepaid, not collect. Do not ship parcel post.
Introduction ��������������������������������������������������������������������������������1
Features ���������������������������������������������������������������������������������������� 1
The User Interface & Connectors ����������������������������� 2
The User Interface ��������������������������������������������������������������������2
Connectors ���������������������������������������������������������������������������������3
Standard Looping �����������������������������������������������������������������������4
Multi-Track Vocal Looping Using JamSync ����������������������������4
Multi-Musician/Multi-Track Looping Using JamSync �����������5
The JamMan® Vocal XT is an easy-to-use vocal looper that is capable of recording phrases of
up to 10 minutes in length, and with unlimited overdubs, you can now be your own backup
vocalist! Use it to create your own vocal harmonies or rhythmic counterpoints in real time�
®
The JamMan Vocal XT features a studio quality dbx
allowing it be used with both dynamic and professional condenser microphones� This
circuitry ensures your vocal signal is consistent and clear during regular performance and
when looping�
The Mic Level control doubles as a multi-color input signal and clip indicator, making it
easy to set the input level for your microphone� The Loop Level control provides a way to
balance loop level with the direct vocal signal� The balanced XLR output can be plugged in
to the line-level or mic-level input of a mixer, providing utmost flexibility�
Using the built-in JamSync™ feature, multiple JamMan Vocal XTs (or any other JamSync
compatible loopers) can be synchronized to provide multi-track looping capabilities! It is
possible to cascade two or more JamMan Vocal XTs for multi-track vocal looping, or sync
with your bandmates’ JamSync compatible JamMan devices for synchronized looping with
other members in the band!
mic preamp with phantom power,
We hope you enjoy the endless fun and simplicity that the JamMan Vocal XT provides�
®
Thanks for choosing DigiTech
�
Features
• XLR Input/Output
• Studio-Quality dbx
• 10 Minutes of Loop Recording Time
• Record Unlimited Overdubs w/Undo & Redo
• JamSync™ Input/Output
• Silent Clear
™
• Simple User Interface w/3 Status LEDs, Loop Level Control, & Footswitch
• Included Power Supply
®
Mic Preamp w/+48V Phantom Power & Gain Control
Prevents Playback When Clearing Loops
1
The User Interface & Connectors
162
345
The User Interface
1. LOOP LEVEL Knob
This knob controls the output level of the
loop� The 12 o’ clock position represents
unity gain�
2. MIC LEVEL Control
Adjust this control to set the input gain
for your microphone� This control also
doubles as a multi-color signal and clip
indicator� It will light green when signal is
present, orange when approaching the clip
point and red when clipping occurs� For
optimal signal to noise performance, set
this control so it lights green and orange
regularly during normal performance and
only lights red rarely on the loudest vocal
signals�
3. Footswitch
This Footswitch is used to perform all
JamMan Vocal XT functions (i�e�, record,
play, overdub, undo/redo, stop, and clear
loop)�
1
2
4
3
4. Status LEDs
These LEDs indicate the status of the pedal as described in the below table�
LEDStatus
REC
PL AY
DUB
DUB
REC
DUB
PL AY
Loop is being recorded.
Loop is playing.
Overdub is being recorded.
Overdub is being undone/redone.
Pedal is in standby
(recording/playback stopped).
LEDStatus
Loop is being cleared
(footswitch held).
REC
Slave armed for record
(connected as slave via JamSync).
REC
Slave synchronization established via
DUB
JamSync.
PL AY
2
Connectors
1. +48V Switch
Engage this switch to enable 48V
phantom power for use with condenser
microphones� Phantom power is on
when the switch is in the ‘in’ position
and off when the switch is in the ‘out’
position�
2. MIC IN Jack
Connect your mic to this XLR jack� If a
condenser mic is being used, the +48V
switch should be enabled (in position)�
3. MIC OUT Jack
Connect this balanced XLR output to
the line or mic input of a mixer, or to
the MIC IN jack of another JamMan
Vocal XT device for multi-track vocal
looping�
4. JAMSYNC OUT Jack
Connect this jack to the JAMSYNC IN
jack on another JamSync compatible
device for master control over loop
playback and stop functions�
5. JAMSYNC IN Jack
Connect this jack to the JAMSYNC
OUT jack on another JamSync
compatible device to slave loop
playback and stop functions to a master
device�
6. Power Jack
Connect only the included power
supply to this jack� The JamMan Vocal
XT can only be powered by using the
external adapter�
3
Connection Diagrams
Standard Looping
CONNECT INCLUDED
MIC
ENABLE +48V FOR
CONDENSER MICS
HARMAN POWER SUPPLY
CONNECT TO
MIC OR LINE INPUT
MIXER
Multi-Track Vocal Looping Using JamSync
CONNECT INCLUDED
MIC
ENABLE +48V FOR
CONDENSER MICS
HARMAN POWER SUPPLIES
JAMSYNC
MASTERSLAVE
CONNECT TO
MIC OR LINE INPUT
MIXER
4
Multi-Musician/Multi-Track Looping Using JamSync
GUITAR AMP
MIC
OUT
20
JAMSYNC
JamMan Solo XT
MASTER
POWER SUPPLY
GUITAR PLAYER
GUITAR
CONNECT INCLUDED
HARMAN POWER SUPPLY
INOUT
VOCALIST
JAMSYNCJAMSYNC
BASS AMP
JamMan Vocal XT
SLAVE 1
IN
CONNECT TO
MIC OR LINE INPUT
MIXER
POWER SUPPLY
BASS
BASS
BASS PLAYER
JamMan Express XT
SLAVE 2
5
Operation
The JamMan Vocal XT was designed to be very simple to use right out of the box� This
section of the manual describes how to perform looping functions�
Recording a Phrase
The JamMan Vocal XT records a single phrase and then plays it back as a continuous loop�
To record a phrase:
1� Press the
solid red and recording will begin�
2� When finished recording, press the
phrase will automatically begin playing back in a repeating loop and the
light solid green�
3� Press the
FOOTSWITCH and begin singing to start recording� The REC LED will light
FOOTSWITCH once to set the loop end point� The
PLAY LED will
FOOTSWITCH 2 times quickly to stop loop playback�
Recording Overdubs
Once a phrase has been recorded, overdubs can be added on top of the phrase�
To record overdubs:
1� Press the
the phrase will begin playing�
2� Press the
yellow and audio will be recorded on top of the phrase�
FOOTSWITCH to start loop playback� The PLAY LED will light solid green and
FOOTSWITCH again to begin overdub recording� The DUB LED will light solid
3� When done overdub recording, press the
session� The loop will continue playing along with the newly recorded overdub�
4� You can now decide whether you would like to undo the last overdub and re-record
it (see "Undoing/Redoing Overdubs" in the following section) or proceed and record
additional overdubs by repeating steps 2-3�
5� Press the
FOOTSWITCH 2 times quickly to stop loop playback�
FOOTSWITCH to end the overdub recording
6
Undoing/Redoing Overdubs
When recording overdubs, you can choose to undo the last overdub recorded if you wish
to re-record it� If you change your mind or accidentally undo an overdub, you can then use
the redo function to retrieve it�
To undo/redo an overdub:
1� Record an overdub as described in the previous section, "Recording Overdubs"�
2� Ensure the loop is playing (the
FOOTSWITCH to initiate loop playback� Once the loop is playing, press and hold
the
FOOTSWITCH for ~2 seconds� The DUB LED will quickly flash yellow, indicating the
the
PLAY LED should be on)� If the loop is not playing, press
overdub has been undone�
3� If you wish to restore the overdub, press and hold the
seconds� The
DUB LED will quickly flash yellow, indicating the redo function has been
FOOTSWITCH again for ~2
performed and you should now hear the overdub again�
NOTE: Each time an overdub is added, the last overdub is merged with the original loop
and can no longer be undone using the undo function� If the combined loop and overdub
length exceed 10 minutes (e�g�, a 6 minute loop and 6 minute overdub, etc�), the two
will automatically be merged and the overdub cannot be undone� Overdubs added to a
recorded loop of 5 minutes or less will not be automatically merged�
Clearing a Phrase
Clearing a phrase allows you to re-record it or record a new phrase� The JamMan Vocal XT
™
has a unique feature, referred to as “Silent Clear
you to play it first� Note that you cannot undo the process of clearing a phrase, so make
sure you want to proceed before performing this function�
”, which clears a phrase without requiring
To clear a recorded phrase:
1� Stop loop playback if it is not already (all LEDs should be off)� If loop playback is active
PLAY LED is on), press the FOOTSWITCH 2 times to stop loop playback�
(the
2� Press and hold the
FOOTSWITCH for ~3 seconds� The REC LED will quickly flash red,
indicating the phrase has been cleared�
NOTE: When using a slave/master looper setup, if the master loop is ~3 seconds or less
and if pressing and holding the
clear on the slave device, you may need to initiate play then stop (3
FOOTSWITCH from a stopped state does not initiate
FOOTSWITCH
presses) and hold the footswitch on the 3rd press to clear its loop�
7
Using JamSync™
1/8” Stereo Cable (TRS)
Record First
Record Second
MIC
Indicates
Slave
Status
Connection & Record Sequence
JamSync allows you to synchronize multiple JamSync compatible devices using optional 1/8”
mini stereo (TRS) cables (see below cable diagram)� This allows a JamSync master to control
the loop playback and stop functions for all connected JamSync slaves, providing multi-track
looping capabilities� You can cascade multiple JamMan Vocal XTs for single-player/multitrack looping or connect to other JamSync compatible devices to collaborate with other
musicians, each recording and cueing their own loops for expressive multi-player/multi-track
looping�
Tip
Sleeve
(Ground)
RingRing
To use JamSync, connect the master
1/8” Mini Stereo (TRS) Cable Diagram
device’s
JAMSYNC IN jack of the first slave
device� The
JAMSYNC OUT jack to the
REC and PLAY LEDs on
the slaved device will briefly flash,
indicating the unit is in slave mode�
Daisy chain any remaining slaves in
the same manner�
When cascading multiple JamMan
Vocal XTs in series and using
JamSync, the last Vocal XT device in
the chain will be the master� You will
want to record to this master device
first, then the second to last device,
etc�, working your way backwards
through the signal chain� Performing
these actions will ensure you record
only what you intend to during each
pass�
Sleeve (Ground)
TO NEXT JAMSYNC SLAVE
Tip
Ring
SLAVE
JAMSYNC
INOUT
OUT
Tip
Sleeve
(Ground)
TO MIXER
MASTER
8
There are two methods for recording loops to a JamSync slaved JamMan device, they are:
• Manual Slave Recording Method
Using this method, you can record to the master then wait until you’re ready to
record to the slave� This method works well if you do not wish to immediately record
to the slave and instead wish to record to the slave at a later time in the song� When
using this method, at the point you are ready to record to the slave, you must arm
the slave for recording before the master device reaches its loop start point� When
the master reaches its loop start point it will send the record command to the
slave device(s), so the slave device must be armed in advance to receive the record
command�
• Sequential Slave Recording Method
Using this method, you can record to a JamSync slave immediately upon setting the
loop end point of the master� Use this method when you want to immediately begin
recording to the slave device after recording to the master device�
To record using the Manual Slave Recording Method:
1� Press the
FOOTSWITCH on the master device and begin singing� The REC LED will light
solid red and recording will begin�
2� When finished recording to the master, press the
FOOTSWITCH once to set the loop
end point� The phrase will automatically begin playing back in a repeating loop and the
PLAY LED will light solid green�
3� Press the
LED
on the slave device will begin flashing red� Once the master device reaches its loop
start point, recording on the slave will begin (the
FOOTSWITCH on the slave device to arm the slave for recording� The REC
REC LED will now light solid red on
the slave device)� Once recording has begun, you can begin singing�
4� When finished recording to the slave, press the slave’s
FOOTSWITCH once to set the
loop end point� The phrase will automatically begin playing back along with the master
loop and the
5� Press the
PLAY LED will light solid green�
FOOTSWITCH on the master device 2 times quickly to stop loop playback on
both devices�
To record using the Sequential Slave Recording Method:
1� Press the
FOOTSWITCH on the slave device� The REC LED will flash red, indicating the
slave is armed for recording�
2� Press the
FOOTSWITCH on the master device and begin singing� The REC LED will light
9
solid red and recording on the master will begin�
Set MIC LEVEL Second
Set MIC LEVEL First
3� When finished recording to the master, press the master
FOOTSWITCH once to set
the loop end point� The master device’s recorded phrase will begin playing back and the
armed slave device will now immediately begin recording, indicated by the slave’s
LED
lighting solid red� Once recording has begun you can continue singing�
4� When finished recording to the slave, press the slave’s
FOOTSWITCH once to set the
REC
loop end point� The phrase will automatically begin playing back along with the master
loop and the
5� Press the
PLAY LED will light solid green�
FOOTSWITCH on the master device 2 times quickly to stop loop playback on
both devices�
Gain Staging daisy chained JamMan Vocal XTs
When daisy chaining multiple Vocal XTs for multi-track vocal looping, you will want to
optimize the gain stucture of each pedal in the siganl chain to achieve the best signal-tonoise performance�
To gain stage daisy chained Vocal XTs:
1� Begin by setting the
MIC LEVEL
on all JamMan Vocal XT’s to the
minimum position�
2� Start singing into the JamMan
Vocal XT and set the
MIC LEVEL
to the optimal level on the device
that the microphone is directly
connected to – for optimal signal
to noise performance, set this
control so it lights green and
orange regularly during normal
performance and only lights red
rarely on the loudest vocal signals�
3� Repeat step 2 on the next device
in the chain (see diagram to the
right)�
TO MIXER
MASTER
JamSync
INOUT
SLAVE 1
10
Specifications
INPUT
Connector Type: Female XLR Pin 2 Hot
Mic Preamp Input Impedance: 330 Ω Balanced
Unity Gain Input to Output: Mic Level control set to 8 o’clock position
Max Input Level at Unity: -3 dBu
Mic Level Gain: +0 to +40 dB
Mic Preamp Phantom Power: 45V
OUTPUT
Connector Type: Male XLR Pin 2 Hot
Output Impedance: 100 Ω Unbalanced / 200 Ω Balanced
Playback Unity Gain: Loop Level knob set to 12 o’clock position
Maximum Output Level: -9 dBu
PERFORMANCE
Sample Rate: 46�8 kHz/24-bit
Max� Individual Loop Time: 10 minutes (stereo)
Frequency Response: +0/-3 dB 20-20 kHz
Signal to Noise Ratio: -100 dB
POWER REQUIREMENTS
Consumption: < 2 Watts typical
Current Draw: < 200 mA typical / < 400 mA max