Instructions 95-8256-02
Ultraviolet Fire Detection System
with Nuclear Surveillance
R7404 Controller/C7051 Detector
Detector Electronics Corporation
6901 West 110th Street •Minneapolis, Minnesota 55438 USA
Tel: 952.941.5665 or 800.765.3473 •Fax: 952.829.8750
7/01 95-8256-02
Table of Contents
SYSTEM APPLICATION ........................................................................1
FEATURES ............................................................................................2
GENERAL APPLICATION INFORMATION ...........................................2
SYSTEM DESCRIPTION .......................................................................3
C7051 Detector ...............................................................................3
R7404 Controller .............................................................................4
THEORY OF OPERATION .....................................................................5
Fire Detection ...................................................................................5
Controller Sensitivity and Time Delay...............................................6
Controller - Fire Logic “Voting” .........................................................6
Controller - Latching Outputs ...........................................................6
NUCLEAR SURVEILLANCE OPERATION ............................................7
Automatic Optical Integrity ...............................................................7
Automatic Fault Identification ...........................................................8
Test Mode .........................................................................................8
Count Test Mode ..............................................................................8
SPECIFICATIONS .................................................................................9
OPTIONS AVAILABLE..........................................................................12
DETECTOR SENSITIVITY ..................................................................12
SYSTEM SENSITIVITY CONSIDERATIONS ......................................12
INSTALLATION ....................................................................................12
Detector Positioning and Density ..................................................12
Mounting and Wiring the Detector .................................................13
Switch Setting Procedure ...............................................................14
Controller Electrical Connections ...................................................17
TYPICAL SYSTEM APPLICATION ......................................................18
STARTUP PROCEDURE ....................................................................18
CHECKOUT PROCEDURE .................................................................18
Manual Check of Optical Integrity .................................................18
Testing of Detector Module Response to UV Radiation
(Count Test Mode) ..........................................................................20
Manual Check in Normal Mode .....................................................20
TROUBLESHOOTING .........................................................................21
Voltages and Waveforms to Aid in Troubleshooting .......................21
Solid State Input and Output Circuitry ............................................21
ORDERING INFORMATION ................................................................21
Accessories ....................................................................................21
DEVICE REPAIR ..................................................................................22
SYSTEM APPLICATION
The R7404 Controller is a significant advance in the DetTronics line of ultraviolet (UV) fire detection equipment,
and broadens the range of capabilities available for fire
protection systems. Incorporating microprocessorbased circuitry, the R7404 increases operational flexibility and at the same time retains important features developed through successive design innovations in several
generations of Det-Tronics equipment. These include
the Automatic Optical Integrity (o
i
) feature, which provides a continuous check of the optical surfaces, detector sensitivity and electronic circuitry of the detector/controller system. Also included is automatic fault identification, which monitors optical integrity, detector supply
voltage, controller operation mode and incoming “fire”
signals, and provides a digital display of system status in
numerical code. Other features retained from previous
generations of Det-Tronics equipment include individual
zone identification and “voting” capability, as well as
manual o
i
testing.
The operational flexibility of the R7404 has led to the
development of the Det-Tronics nuclear surveillance
(count subtraction) fire detection system, which automatically compensates for x-rays or gamma radiation that
might otherwise cause false actuation of the system. The
detector consists of a UV detector module mounted next
to a similar detector module that is blinded to UV. The
sensor tubes within the detector module pair are electronically matched for identical response to external radiation. The blinded detector module can only respond to
x-rays and gamma radiation, while the fire detector module can respond to UV as well as x-rays and gamma radiation. The controller subtracts the blinded detector’s signal from the fire detector’s signal. The remainder represents only the UV radiation, if present.
The C7051 Detector is sensitive to the UV radiation that
is emitted by a flame, and is designed for hazardous
locations. It is particularly suitable for use in outdoor
applications because it is not affected by wind or rain
and is insensitive to solar radiation. In addition, the
detector does not respond to normal artificial light.
Typical applications for Det-Tronics UV detection systems are:
— Wherever highly combustible materials are involved
— Where there is a need for fast response (0.5 second)
to flame
— Where there is a large capital investment to be pro-
tected.
Examples of actual installations using the Det-Tronics UV
detector in automated fire protection systems include:
7/01 95-8256-02
INSTRUCTIONS
Ultraviolet Fire Detection System
with Nuclear Surveillance
R7404 Controller
C7051 Detector
DET-TRONICS
©Detector Electronics Corporation 2001
*o
i
is Detector Electronics' Trademark for its patented Optical
Integrity Systems. U.S. Patent 3,952,196, United Kingdom Patent
1,534,969, Canada Patent 1,059,598.
®
Solid Materials
— Munitions production such as illuminating flare mate-
rial, TNT, black powder and other propellants
Other Processes
— Chemical and petrochemical production
Information on these and a wide variety of applications is
available from Detector Electronics.
FEATURES
• Automatically compensates for nuclear radiation.
• Detectors operate under adverse weather conditions
such as wind, rain, snow, high humidity, and
extremes of temperature or pressure.
• Automatic Optical Integrity.
• All automatic test functions performed with the system on line.
• Manual oitest capability (in addition to Automatic o
i
capability).
• Automatic fault identification.
• Individual zone identification.
• Microprocessor control.
• Both fire and fault outputs have redundant indication,
i.e. digital readout and separate LED.
•Output circuits can be made latching or non-latching
through field adjustment.
• Keylock switch for setting the controller mode to
NORMAL, RESET or TEST.
• Power supply will accommodate high direct current
transients such as those associated with battery
charging.
• TEST/ACCEPT button for silencing external audible
signaling devices.
• LAMP TEST button for checking all panel LEDs and
digital display segments while the system is on line.
• Individual detector count rates can be measured and
observed on the digital display.
• Digital display signal output available at field wiring
terminals for coupling to computers or other equipment.
GENERAL APPLICATION
INFORMATION
In applying any type of sensing device as a fire detector,
it is important to know of any conditions that may prevent
the device from responding to a fire, and also to know
what other sources besides fire will cause the device to
respond. A UV detector is useful in fire protection applications because it will provide very fast response to the
presence of ultraviolet radiation emitted by a flame. In
addition, it is the only type of sensor that is not affected
by environmental conditions such as wind, rain, or
extremes of temperature and pressure. The Det-Tronics
UV system is also insensitive to the ultraviolet component
of solar radiation.
Considering the above, it can be seen that there are fire
detection applications where only ultraviolet sensors are
suitable. However, success in using an ultraviolet detector is dependent not only on knowing its advantages, but
also its limitations. High atmospheric electrostatic potential can cause false actuation of an ultraviolet detection
system if its detectors are not correctly grounded.
Electric arc welding is a source of intense ultraviolet radiation, and care must be taken to ensure that arc welding
is not performed in protected areas without securing the
detector. In addition, UV detectors should not be positioned so that their cone of vision can scan the horizon.
Rather, they should be directed down over the designated hazardous area to reduce the likelihood of picking up
UV radiation from distant sources.
2
Nuclear radiation is also a potential cause of false actuation of the detection system. X-rays and gamma radiation easily penetrate the metal housing of the detectors,
causing the UV sensor tubes to react in the same way as
they would to UV radiation. While the nuclear surveillance system compensates for x-rays and gamma radiation present in the protected area, care must be taken
that the C7051 Detectors are aligned in such a way that
the blinded detector sections are between the nuclear
radiation source and the UV detector sections. If the
blinded detector section intercepts less nuclear radiation
than the fire detector section, false system actuation can
result. Consult “Installation” section for further details.
An important fact regarding UV detectors of any type is
that ultraviolet radiation must reach the detectors in order
for them to respond. Care must be taken to keep
obstructions out of the line of view. For a UV detector,
this means that ultraviolet absorbing gases or vapors as
well as physical obstructions must not be allowed to
come between the detector and the protected hazard.
Smoke will absorb UV radiation, and if accumulations of
dense smoke can be expected to precede the presence
of flame, then UV detectors should not be used alone.
It must be noted that malfunctions can occur in any type
of equipment, and although Det-Tronics systems are
subjected to rigorous tests before shipment, no way has
yet been found to guarantee that every device will
always operate perfectly. The highest reliability with
regard to response to a fire is achieved when a hazardous area is supervised by more than one detector,
and when each detector can independently register an
alarm.
SYSTEM DESCRIPTION
The nuclear surveillance system consists of one to four
R7404 Controllers that are wired and programmed to
monitor up to sixteen C7051 UV/nuclear radiation detectors.
Each controller can accommodate up to four C7051
Detectors. Figure 1 is a simplified diagram of a nuclear
surveillance system.
C7051 DETECTOR
The C7051 Detector (Figure 2) incorporates two DetTronics C7050 type UV detector modules. Each module
holds a Geiger-Muller type sensor tube, circuitry to
process and transmit an output signal, and a UV test
lamp (“source tube”) which is used to test the sensor
tube. The two sensor tubes are sent from the factory as
a matched pair; both are selected for their identical
response to UV and nuclear radiation. One detector
module is blinded to UV; both are responsive to x-ray
and gamma radiation. When UV or nuclear radiation
strikes the cathode of the sensor tube, a series of voltage
pulses is sent to the controller. The frequency of the
pulses is proportional to the intensity of the UV or nuclear
radiation. Each detector module is connected to the
controller by three wires (see “Installation”). The wires
are referred to as A-, B-, and D- leads.
1. The A- lead is connected to the +290 vdc supply.
2. The B- lead is the “signal” line (sensor tube to controller).
3. The D- lead is the test lamp control line.
Each module is housed in an explosion-proof enclosure
designed to meet most national and international standards.
NOTE
It is required that the C7051 Detector housing be
connected to earth ground to avoid the possibility of
false detector actuation in areas with high electrostatic potential. A grounding lug is provided for this
purpose at the junction box.
3 95-8256
Figure 1—Simplified Block Diagram - Nuclear Surveillance System
UV
UV
UV
UV
FIRE
BLINDED
FIRE
BLINDED
C7051
DETECTOR
C7051
DETECTOR
FIRE
CONTROLLER
SOLID
STATE
OUTPUTS
BLINDED DETECTOR
SIGNAL IS SUBTRACTED
NUCLEAR
RADIATION
FROM FIRE DETECTOR
SIGNAL
R7404 CONTROLLER
Microprocessor technology has made possible a degree
of programming flexibility that could not be achieved in
previous generations of Det-Tronics systems. The R7404
Controller incorporates a microprocessor and a programmable memory to store and implement the permanent program for operating the system. The operating
program continuously cycles through the Automatic
Optical Integrity test, checking each detector and its
wiring. The microprocessor can be interrupted by any
one of several status changes, such as a fault, a UV signal from one of the C7051 Detectors, or a change in the
setting of the keylock switch. In the event of a status
change, the microprocessor will react to the change.
The output of the controller is interpreted by other surveillance/fire detection controllers in the system for voting purposes. The controller provides solid state outputs
that are activated in response to fire signals from the
C7051 Detectors, and to status occurrences such as
system faults.
In the nuclear surveillance system, fire detection and surveillance functions are controlled by the same R7404
Controller. The operating program of each R7404 determines its wiring and switch setting configuration as well
as its mode of operation.
Front Panel
The front panel of the R7404 Controller (Figure 3) pro-
vides switches and indicators to enable manual o
i
and
data bus tests (see “Checkout Procedure”) and to identify output actuation and status occurrences.
1. The green POWER LED is illuminated whenever
power is applied to the controller.
2. The amber FAULT LED is illuminated in the event of
a system malfunction or an undesirable status
occurrence (see “Theory of Operation - Fault
Identification”).
3. The amber INHIBIT LED is illuminated when the
controller is reset or placed in the test mode. It
indicates that all solid state outputs are disabled.
(See “Theory of Operation” and “Installation” sections.)
4. The red FIRE LOGIC A and B LEDs are illuminated
when the solid state fire logic outputs are actuated.
(See “Theory of Operation”.)
5. The eight ZONE OUTPUT LEDs correspond to the
eight detector inputs. See “Theory of Operation”
for details. The ZONE OUTPUT LEDs are red for
the fire protection zones and green for the remote
surveillance zones.
6. The upper digital display on the front panel identifies the number of the zone involved in any system
status occurrence on the ZONE display. Since the
nuclear surveillance system is restricted to one
detector per zone, the DETECTOR display will
show a “0” whenever it is activated. (See “Theory
of Operation.”)
7. The lower digital display identifies by code number
system status occurrences such as fire or fault conditions. Table 1 is a list of the status codes and
their interpretations.
4
INDEX PIN
Figure 2—C7051 Detector Assembly
TERMINAL BLOCK
UV DETECTOR TUBE
QUARTZ WINDOW AND HOUSING
Oi REFLECTIVE RING
TERMINAL BLOCK
RADIATION DETECTOR TUBE
BLINDED WINDOW
8. The SELECT and TEST/ACCEPT buttons are used
to manually test each detector (see “Checkout
Procedure” section). The SELECT button is used to
sequentially select each detector for test. The
TEST/ACCEPT button is used to activate the manual
o
i
test in each detector when the controller is in
the bypass mode. When the controller is in the normal mode, the TEST/ACCEPT button performs an
alarm accept function that can be used to de-activate an alarm circuit without interrupting zone and
fire logic outputs. (See “Theory of Operation” for
details.)
9. The LAMP TEST button is used to illuminate all
LEDs and digital display segments in order to verify that they are operational. The lamp test can be
performed in the normal mode, since it has no
effect on the system’s operation.
10.The keylock switch is used to select normal and
test modes and to reset the controller. (See
“Theory of Operation” section.)
Field Wiring Connectors
The R7404 Controller is furnished with a field wiring connector that incorporates pressure type screw terminals
for attaching wires and circuit board edge connectors for
plugging the controller in. Each terminal will accept two,
22 gauge wires. Refer to the “Installation” section for a
detailed description of terminal configurations.
Programming Switches
The R7404 is furnished with four rocker switch assemblies that are used to select options such as detectors
connected, time delay, fire logic, controller sensitivity,
master/slave position and latching/non-latching. Refer to
the “Theory of Operation” and “Installation” sections for
a detailed explanation of the programming options. It is
essential that the controller be properly programmed
before applying power to the system.
THEORY OF OPERATION
FIRE DETECTION
When a detector senses ultraviolet (UV) radiation, it generates a series of voltage pulses and transmits them to
the controller. A counter circuit in the controller samples
the incoming signals (or count rate). In the nuclear surveillance system, two factors are weighed against the
count rate of the detector signals. First, the count rate of
the blinded detector modules must be subtracted from
the incoming count rate of the fire detector modules.
After the nuclear surveillance data value has been subtracted, the new adjusted count rate is compared to a
pre-programmed sensitivity setting. (See “Installation Switch Setting Procedure.”) If the adjusted count rate
exceeds the sensitivity setting for a pre-programmed
timer interval, the fire controller’s microprocessor will
generate the following response:
1. The appropriate zone output(s) is energized (solid
state - open collector) and the corresponding
ZONE OUTPUT LED blinks. Each of the four detector pairs is matched with its own zone output and
ZONE OUTPUT LED.
5 95-8256
Figure 3—Front Panel - Nuclear Surveillance Controller
0 — Keylock switch in RESET position, or external
Inhibit/Reset is activated.
1 — Keylock switch in TEST position.
2 — Reduced detector sensitivity (oi fault), or faulty
wiring.
3 — Spurious detector operation, or high background
radiation.
4 — Low +290 vdc (+290 volt detector supply wire may
be shorted).
5 — High +290 vdc (voltage regulation failure in the 290
volt supply).
6 — Fire (Zones 1-4 only).
7 — Count subtraction lockout.
8 — Controller in count test mode.
9 — Data Link Failure (faulty data transfer).
Table 1—System Status Codes
RED LEDS
ZONES 1-4
GREEN LEDS
ZONES 5-8
RED LEDS
DETECTOR SELECTION
AMBER LED
GREEN LED
DETECTOR TEST/
ALARM ACCEPT
AMBER LED
LAMP TEST
KEYLOCK SWITCH
2. The alarm output is energized (solid state - open
collector). The alarm is activated when any zone
detects a fire.
3. The ZONE display shows the number of the first
responding zone. The DETECTOR display is
blank.
4. The SYSTEM STATUS display shows a “6”, indicating fire.
5. If the voting criteria (see below) have been satisfied, the fire logic output is energized and the fire
logic LEDs are illuminated.
NOTE
When the UV signal (count rate) falls below the
sensitivity threshold, the zone and fire logic outputs are de-activated and their corresponding
LEDs are turned on (steady state). If the latching
option (see below) has been selected, the outputs
will remain activated and their corresponding
LEDs will continue to blink. The alarm output is a
latching output and will remain activated after the
UV signal has been removed.
CONTROLLER SENSITIVITY AND TIME DELAY
The R7404 Controller can be programmed to respond
only when a specific level of UV radiation has been
exceeded, and to require that the duration of the radiation is greater than a desired time period (see also:
“Installation” section). Selection of controller sensitivity
and the time delay to be used in a given application is
dependent on the level of hazard present, and the action
to be taken in the event of a fire. The programmable
sensitivity and time delay of the R7404 system allow it to
meet the requirements of virtually any application.
Sensitivity is field programmable (in increments of 8 cps)
over a range of 8 through 120 counts per second. The
maximum response distance (highest sensitivity) is
achieved at an eight cps sensitivity setting. For applications involving high background UV radiation potential,
the system can be desensitized by increasing the count
rate required to actuate it. The 120 cps setting (minimum
sensitivity) results in the minimum response distance.
The fire response output signals can be delayed (in
quarter second intervals) over a range of 0.5 to 8.25 seconds.
Although there is one delay setting for the entire controller, the response of each zone output is affected by
the time delay individually. For example: If zone one
detects a fire, the zone one output will be activated provided UV radiation is continuously detected for the preselected time delay. If zone three detects a fire at a later
time, the microprocessor will again require that UV is
detected continuously for the time delay period before
activating the zone three output.
NOTE
Setting the controller at maximum sensitivity and
minimum delay may increase the possibility of
false system actuation. Consult Detector
Electronics’ Customer Service Department if such
a setting is desired.
CONTROLLER - FIRE LOGIC “VOTING”
“Fire Logic” is activated when a preset number of zones
sense UV radiation (see “Installation” section). Up to
four zones can “vote” together. Specifically, the controller can be programmed so that one, two, three or four
of zones 1 to 4 detect fire before activating the fire logic
output. Unless the controller is programmed for latching
outputs (see below), voting criteria can be satisfied only
by simultaneously activated zones. Figure 4 is a brief
flow chart of fire logic selection and voting.
The external data bus is used to connect up to four controllers so that up to 16 detectors can vote together.
The Det-Tronics “voting” principle allows combinations of
detectors to fulfill voting requirements and represents the
best balance between reliability of fire detection and
freedom from false actuation due to individual detector
malfunction.
CONTROLLER - LATCHING OUTPUTS
The controller can be field-programmed to have latching
or non-latching outputs (see “Installation” section). If the
controller is programmed for latching outputs, all
responding zone and fire logic outputs will remain activated (6-status) until manually reset. If the controller is
programmed for non-latching outputs, all activated
zones and fire logic outputs will be deactivated and their
respective LEDs will be illuminated (steady state) after
UV radiation has been removed. The alarm output is
latching and, once activated, will remain so until manually reset (via the TEST/ACCEPT button or the External
Accept input). When the controller is programmed for
latching outputs, the fire logic (voting) criteria can be satisfied by detector zones that are latched on. In this case,
simultaneous detection of fire is not required to satisfy
voting criteria.
6
NUCLEAR SURVEILLANCE
OPERATION
The C7051 Detector includes two sensor modules
mounted on one base. The sensors are paired at the
factory for identical response to x-rays and gamma radiation. One detector module is blinded to UV radiation
but detects nuclear radiation. The other detects both UV
and nuclear radiation. Both modules view the same
area. The blinded detector module is placed closer to
the radiation source than the fire detector, so that it
absorbs as much or more nuclear radiation as the fire
detector. Up to four C7051 assemblies can be used with
one R7404.
The count rate of the blinded detector module corresponds to the intensity of nuclear radiation in the area to
be protected. The count rate of the fire detector module
corresponds to the intensity of the nuclear radiation plus
the UV radiation present in the protected area. The
blinded detector module’s count rate is subtracted from
the fire detector module’s count rate. The remainder corresponds to the UV radiation intensity in the protected
area. On the controller, zones one through four correspond to fire detector modules and zones five through
eight correspond to surveillance detector modules. The
output of detector 5 is subtracted from detector 1, detector 6 from detector 2, and so on. Though the 5 - 1, 6 - 2,
7 - 3, and 8 - 4 pairs correspond to different detectors on
the controller, each pair corresponds to a single C7051
Detector. (See also the “System Sensitivity
Considerations” and “Switch Setting Procedure” sections.)
AUTOMATIC OPTICAL INTEGRITY
An important consideration with any UV fire detector is
that an accumulation of contaminants (oil, gasoline, dirt)
on the quartz window will absorb or block UV radiation.
Contamination on the window great enough to completely obscure UV from the detector can be virtually undetectable to the human eye.
To ensure that the detectors are operational, the
Automatic o
i
program continuously cycles through a test
of each detector module and its wiring. Both the blinded and the unblinded modules of the C7051 Detector
incorporate a UV sensor tube and an optically isolated
UV test lamp.
In the unblinded module, actuation of the test lamp
causes UV radiation to travel out through the quartz win-
dow, where it encounters a reflective o
i
ring and is
directed back through the window to the sensor tube. If
the window is clean, the sensor tube detects the UV from
the lamp and sends a signal back to the controller to verify that the detector module and its wires are functioning
properly. See Figure 5.
The blinded detector module is tested the same way,
except that only the sensor tube is tested, since there is
on quartz window to check.
The R7404 tests its detectors at the rate of approximately one per second, so that if a fault occurs, it is almost
instantly detected.
7 95-8256
ANY ONE OR
Figure 4—Fire Logic Selection and Voting Sequence
MORE ZONES
SEE FIRE
FIRE
LOGIC
SELECTED
ZONE OUTPUT(S)
YES
NO
YES
NO
YES
NO
YES
ANY TWO OR
MORE ZONES
SEE FIRE
ANY THREE OR
MORE ZONES
SEE FIRE
ANY FOUR OR
MORE ZONES
SEE FIRE
ONE ZONE
SELECTED?
NO FIRE LOGIC
OUTPUT
TWO ZONES
SELECTED?
NO FIRE LOGIC
OUTPUTS
THREE ZONES
SELECTED?
NO FIRE LOGIC
OUTPUTS
FOUR ZONES
SELECTED?
FIRE LOGIC
OUTPUT
A AND B
ZONE OUTPUTS
FIRE LOGIC
OUTPUT
A AND B
ZONE OUTPUTS
FIRE LOGIC
OUTPUT
A AND B
ZONE OUTPUTS
FIRE LOGIC
OUTPUT
A AND B
The basic operation of the Automatic o
i
program
involves selecting and illuminating a UV test lamp, sensing a return signal from the detector, turning off the UV
test lamp, sensing the termination of the return signal,
and selecting and illuminating the next UV test lamp. In
the R7404 nuclear surveillance system, all detector modules (both surveillance and fire protection) are continually checked by the microprocessor programs of the controller.
AUTOMATIC FAULT IDENTIFICATION
In the event of a system malfunction, the microprocessor
branches to an automatic fault identification program.
This feature operates much the same as on previous
generations of Det-Tronics equipment. When a fault
occurs, the (normally energized) solid state fault output
is de-energized, the FAULT LED is illuminated and the
STATUS and ZONE displays are activated to identify the
fault code and (when applicable) the number of the
affected zone. Because there is only one detector module per zone, the DETECTOR display will show “0” whenever a status change is identified. When a non-fault status indication such as “fire” (6-status) occurs, the fault
output remains energized, and the FAULT LED is not
turned on, but the STATUS and ZONE displays are activated to indicate the status code and number of the
affected zone.
Depending on the zone affected, the 3-status can have
one of two meanings. If the STATUS display shows “3”
and the ZONE display indicates zones 1 to 4, the count
rate of the sensor tube affected has exceeded 50 percent of the controller’s sensitivity setting. If this occurs, a
separate “LOW LEVEL ALARM” output is activated (terminal 39), but the FAULT output is not activated.
If the STATUS display shows “3” and the ZONE display
indicates zones 5 to 8, the blinded surveillance detector
indicated may be in a “runaway” state, uncontrollably
generating counts. This can be checked by using the
count mode test of the controller as described in the
“Checkout” section. If the sensor tube in the blinded
detector module is in a “runaway” state, it and its counterpart in the fire detector module must be replaced.
Tables 1 and 5 provide an explanation of the STATUS
codes of the nuclear surveillance controller.
TEST MODE
Although the automatic optical integrity and fault identification features provide continuous monitoring of most of
the system circuitry, a microprocessor controlled test
mode provides a means to positively determine that the
system is operational. The controller is placed in the test
mode by turning the keylock switch to the TEST position.
When the controller is placed in the test mode, the following occurs:
1. Fault output is de-energized and the FAULT LED is
illuminated.
2. Outputs inhibited output (see “Installation” section)
is energized and the INHIBIT LED is illuminated,
indicating that all other outputs are disabled.
3. SYSTEM STATUS display shows a “1”.
4. DETECTOR display shows a “0”.
5. ZONE display indicates the number of the highest
numbered zone.
In the test mode, the SELECT and TEST buttons are
enabled. Pressing the SELECT button causes the microprocessor to step to the next lower zone, allowing another detector to be selected for testing. When the TEST
button is depressed, the UV test lamp of the detector
under test is turned on. After the pre-selected time
delay, the ZONE LED that corresponds to the detector
under test will blink. Because the controller outputs are
inhibited, the data bus or corresponding zone output will
not be energized.
COUNT TEST MODE
The count test is a means of determining the response of
each detector in the system. To enter the count test
mode:
1. Place the keylock switch in the TEST position.
8
UV TEST LAMP
Figure 5—Fire Detector Module with Oi
OPTICAL SHIELD
UV DETECTOR
UV SENSOR
SNAP-IN oi RING
VIEWING WINDOW
C784
2. Depress the TEST and SELECT buttons simultaneously and then release.
3. The STATUS display will show an “8” and the
DETECTOR and ZONE displays will show a “0” and
the number of the zone under test respectively.
The SELECT button serves the same function as in the
test mode described above. When the TEST button is
pressed, the UV test lamp in the selected detector is illuminated and the sensor sends a response back to the
controller. The DETECTOR and ZONE displays indicate
the response of the UV sensor under test (in cps). If the
FIRE LOGIC LEDs turn on, multiply the displayed count
by ten. The count rate should be between 50 and 300.
SPECIFICATIONS
SPECTRAL SENSITIVITY RANGE—
Det-Tronics ultraviolet fire detectors respond to radiation
over the range of 1850 to 2450 Angstroms (see Figure 6).
Detectors are insensitive to direct or reflected sunlight
and to normal artificial lighting.
NOTE
High electrostatic forces will affect the detectors if
exposed directly at the window. Arc welding is an
intense UV source, and special application techniques are required to restrict this radiation from the
detector’s cone of vision.
OPTICAL SENSITIVITY RANGE
(CONE OF VISION)—
The fire detector module of the C7051 Detector has a
nominal 90 degree cone of vision with the highest sensitivity lying along its central axis. Figure 7 shows a composite view of the cone of vision and the detector
response to a constant UV source at various relative distances. Depending upon the intensity of the UV radiation
source, the C7051 can be considered to have a practical application distance of up to about 50 feet (15
meters) when set to 24 cps. Since physical obstructions,
smoke accumulation or UV absorbing chemical vapors
will prevent UV from reaching the detectors, they should
be mounted as close as practical to the probable hazard. Under certain controlled conditions, detectors may
be used at greater distances.
SYSTEM SENSITIVITY—
Sensitivity for R7404 Controllers is field adjustable over a
range of 8 through 120 counts per second (cps) in increments of 8 cps. The system should be set at no higher
a sensitivity than the minimum required for adequate
response to flame or explosion. The maximum response
distance (maximum sensitivity) is achieved at an 8 cps
sensitivity setting. For applications involving high background radiation potential, the system can be desensitized by increasing the count rate required to actuate it.
The 120 cps setting (minimum sensitivity) results in the
minimum response distance.
NOTE
Setting the controller at maximum sensitivity and
minimum delay may increase the possibility of
false system actuation. Consult Detector
Electronics’ Customer Service department if such
a setting is desired.
9 95-8256
ATMOSPHERIC
Figure 6—UV Detector’s Range of Sensitivity
Figure 7—Detector Cone of Vision
TRANSMISSION
B1015
100
75
50
25
0
ULTRAVIOLET
SOLAR RADIATION
REACHING THE EARTH
VISIBLE INFRARED
5.04.03.02.01.51.00.90.80.70.60.50.40.30.20.1
WAVELENGTH (MICRONS)
100% REPRESENTS THE MAXIMUM DETECTION DISTANCE FOR A
GIVEN FIRE. THE SENSITIVITY INCREASES AS THE ANGLE OF
30°
45°
INCIDENCE DECREASES.
VIEWING ANGLE
15°
DETECTION
DISTANCE
(PERCENT)
0°
100
90
80
70
60
50
40
30
20
10
15°
30°
45°
INPUT VOLTAGE—
The R7404 is designed to operate from any voltage in the
range of 10 to 38 volts dc. For ac line (mains) voltage
operation, an optional voltage converter (model W4220)
is available from Det-Tronics.
TEMPERATURE RATING—
Operating: Detector: -40°F to +167°F
(-40°C to +75°C).
Controller: -40°F to +158°F
(-40°C to +70°C).
Storage: -67°F to +170°F (-55°C to +77°C) for the
system.
R7404 OUTPUT CIRCUIT RATINGS—
Open collector solid state output is rated 100 milliamperes dc and is transient protected by an “inherent”
zener diode. Lead monitoring is provided by an internal
100 kilohm resistor from output to ground. The output
transistors are rated at 60 vdc. External equipment that
may generate transients when switching (such as relays)
should have a transient suppression device connected
across the coil at the time of installation. This will safeguard the output transistors in the R7404.
POWER CONSUMPTION—
Standby condition: 1.5 watts typical, 1.7 watts maximum.
Fire condition (all detectors responding): 15 watts typical, 16.5 watts maximum.
WIRING REQUIREMENT—
A shielded wire is required for the B-lead from each zone
to the controller, 22 gauge, 300 volt rms rating minimum.
Each detector also requires an individual wire (D-lead)
for actuation of the UV test lamp (shielded wire is recommended). Use a common wire for all detectors for the
+290 volt dc supply (A-lead). The detectors may be
located up to 2000 feet (600 meters) from the controller.
An 18 gauge wire from each detector housing to earth
ground is required for prevention of false detector actuation due to high electrostatic charges.
Characteristics of 22 Gauge Copper Wire
Metric U.S. Customary
Diameter 0.6439 mm 0.02535
Cross Section 0.3255 mm2 0.0005 in2
Resistance 33.3 ohm/km 10.15 ohm/1000 ft
SHIPPING WEIGHT (APPROXIMATE)—
Pounds Kilograms
R7404 Controller 2.5 1.1
C7051 Detector (aluminum) 6.0 2.7
DIMENSIONS—
The dimensions given for the R7404 Controller in Figure
8 are for the unit only. If the optional Q4004 Mounting
Cage is used, the dimensions given in Figure 9 apply.
See Figure 10 for mounting dimensions of the C7051
Detector.
DETECTOR ENCLOSURE RATINGS—
Watertight, dust-tight, designed to meet NEMA standards Publication IS 1.1-1975 for type 4 enclosures.
CSA certified Enclosure 4.
Hazardous locations: Designed for Class I, Groups B, C
and D; Class II, Groups E, F and G. CSA Certified for
Class I, Groups C and D; Class II, Groups E, F and G.
10
Figure 8—Dimensions of R7404 Controller in Millimeters (Inches)
9.5 (242 MM)
2.0
(50MM)
7.0
(177 MM)
F234
11 95-8256
RACK PART NUMBER CONTROLLER
Figure 9—Dimensions of Q4004 Mounting Cage in Inches (Millimeters)
Figure 10—Dimensions of C7051 Detector in Inches (Millimeters)
TYPE 005269-XXX POSITIONS FOR: HT: DIM. (A) DIM. (B) DIM. (C) DIM. (D) DIM. (E) WEIGHT
FIRE GAS INCH MM INCH MM INCH MM INCH MM INCH MM LB KG
4U –001 8 16 4U 19.00 482.6 18.30 464.8 17.36 440.9 4.00 101.6 6.97 177.1 9.3 4.2
4U –002 6 12 4U 15.06 382.6 14.36 364.7 13.42 340.9 7.6 3.5
4U –003 4 8 4U 11.13 282.6 10.43 264.9 9.49 241.1 5.9 2.7
4U –004 3 6 4U 9.16 232.7 8.46 214.9 7.52 191.0 5.1 2.3
4U –005 2 4 4U 7.19 182.7 6.49 164.9 5.55 141.0 4.2 1.9
4U –006 1 2 4U 5.22 132.6 4.52 114.8 3.58 90.9 3.1 1.4
(A)
(B)
(C)
1.48 (37.59)
(E)
(D)
ALL CONTROLLER CAGES REQUIRE
A MINIMUM OF 10.12 INCHES (257.1 MM)
DEPTH CLEARANCE
B1475
3.38 (85.8 MM) 7.11 (181 MM)
2.5 DIA.
(64 MM)
7.81
(198 MM)
5.25
(133 MM)
C1047
CONDUIT ENTRY 3/4 NPT OR 25 MM
OPTIONS AVAILABLE
• R6006 Relay Output Module to be used in conjunction with the R7404 when relay switching contacts are
required. Four models are available. The R6006A
has six fire relays, one fault relay, and one alarm relay.
The R6006B has eight fire relays. The R6006C and D
are functionally identical to the R6006A and B
respectively, with the addition of an output load monitoring feature. The relays in the R6006 have form C
(normally open/normally closed) contacts that are
capable of operating fire alarm devices requiring up
to 3 amperes at 30 vdc or 250 vac. Refer to form 901016 for more information.
• W4220 Voltage Converter for operating the R7404
from line (mains) voltage. The W4220 Voltage
Converter is designed to furnish operating power for
up to eight modules of the Det-Tronics Fire Detection
System. It is available with either two or four channels, each separately fused and completely separate. Should a fault occur in one channel, the others
are unaffected. It is styled and sized to be compatible with other modules when mounted with them in
the Det-Tronics Q4004 Mounting Cage. Refer to form
95-8243 for more information.
• Q4004 Mounting Cage (Figure 9) designed for holding up to 8 modules in a standard 19 inch instrument
rack. The Q4004 is recommended for ease of installation and service.
DETECTOR SENSITIVITY
The Detector Electronics ultraviolet fire detector uses a
Geiger-Muller type detector designed to respond to radiation over a wavelength of 1850 to 2450 Angstrom units
(10,000 Angstroms = 1000 nanometers = 1 micron =
0.001 millimeter). Figure 6 illustrates the sensor tube’s
range of sensitivity, and compares this range to other
forms of radiation. Note the UV radiation reaching the
earth from the sun does not extend into the detector’s
range of sensitivity. In addition, radiation from normal
(properly screened) artificial lighting (fluorescent, mercury-vapor and incandescent lamps) does not extend
into the detector’s spectral range. As a result, the detector is insensitive to these forms of radiation and may be
used outdoors or indoors. Some mercury-vapor lamps
can operate for extended periods with cracked or otherwise damaged envelopes, and will then emit UV radiation in the frequency response range of the Det-Tronics
detector. Defective mercury-vapor lamps can cause eye
irritation and should be immediately removed from service.
The UV sensor responds to any radiation which can penetrate its glass envelope and create ion pairs. The glass
envelope absorbs most alpha or beta particles, but it
permits both gamma and x-rays to pass through. If
these rays create ion pairs between the electrodes near
the cathode, the normal discharge process will occur
and the detector will produce a count. If the x or gamma
ray flux is sufficient to produce a count rate higher than
the system sensitivity setting, an undesired actuation of
the system may occur.
By automatically compensating for the extra counts produced by radioactivity, the C7051 Detector assembly
keeps the UV detection system functional in locations
where radioactivity is present.
SYSTEM SENSITIVITY CONSIDERATIONS
Because of the complexity of the combustion process,
the UV detector count rate generated by different size
fires viewed from the same distance is difficult to predict
with a high degree of precision. In general, however, if a
fire doubles in size, the detector count rate is increased
by approximately 60 percent.
Selection of the controller sensitivity and time delay to be
used in a given application is dependent on the level of
hazard present and the action to be taken in the event of
fire. The adjustable sensitivity and time delay of the
R7404 system allows it to meet the requirements of virtually any application. For sensitivity and time delay
adjustment information, see the “Installation” section.
INSTALLATION
DETECTOR POSITIONING AND DENSITY
As previously stated, the Det-Tronics detector has a
nominal 90 degree cone of vision. What this means in
practical terms can be understood by reference to a typical installation. Consider an application with a ceiling
height of 25 feet (7.5 meters) and assume it is desired to
have complete detector coverage at floor level. If a
detector is mounted 2 feet from the ceiling and pointed
straight down, the distance from the detector to the designated level is 23 feet (7 meters). Because of its 90
degree cone of vision, the detector covers a circular area
with a diameter of 39 feet (12 meters). A simple layout of
the area to be covered will easily reveal the number of
detectors required to completely supervise the designated area.
12
In general, fire detectors should be placed as close as
practical to the probable hazard. The (blinded) nuclear
surveillance module of the C7051 Detector must be positioned at least as close, if not closer, to the source of
radioactive interference as the fire detector module. See
Figure 1.
Det-Tronics systems may be adjusted to various sensitivity levels by programming the controller to respond at a
pre-determined detector count rate. This count rate is
dependent upon the intensity of ultraviolet radiation
reaching the detector, which is a function of fuel, flame
size, distance from the detector and the amount of UV
absorbing vapors present. Programming the controller
to respond to a low count rate results in high system sensitivity. Conversely, programming the controller to
require a high count rate results in low system sensitivity.
The possible presence of UV absorbing vapors must be
examined closely. Some chemical and petrochemical
vapors have very strong UV absorption characteristics.
For a listing of UV-absorbing vapors, contact Detector
Electronics Corporation, Customer Service.
NOTE
Do not mount UV detectors close to the ceiling in
enclosed areas if dense smoke may be expected
to accumulate at the onset of a fire. Mounting the
detector on side walls a few feet (or about 1
meter) down from the ceiling will normally allow
time for the detectors to respond before they are
affected by smoke rising to the ceiling. It is also
advisable to shorten the time delay settings for
applications where smoke may accumulate during a fire. A smoke/fire detector is available for
use in applications where dense smoke might
accumulate prior to the presence of flame (as in
an electrical fire). Consult Detector Electronics’
Customer Service department for details.
MOUNTING AND WIRING THE DETECTOR
The wiring to each detector must be 22 gauge (0.643
mm diameter) minimum, with at least a 600 volt rms rating. The B-leads from each detector must be individually shielded. If the B-leads are run in conduit, the conduit
must not be used for wiring from other electrical equipment. Shielded wiring is recommended for the A-leads
and the D-leads. The A-lead can be common to all
detectors connected to one controller, but each detector
must have a separate D-lead to the controller to operate
the o
i
system. Each detector may be located at a dis-
tance of up to 2000 feet (600 meters) from the controller.
A grounding screw is provided inside the housing for
connecting the C7051 to earth ground. It is recommended that a conduit seal, drains and breathers be
used. Seals should be installed immediately behind the
detector module to provide a watertight enclosure. In
some applications, alternate changes in temperature
and barometric pressure cause “breathing,” which
allows the entry and circulation of moist air throughout
the detector and connected conduit. Joints in the conduit system and its components are seldom tight enough
to prevent this breathing. Moisture in the air condenses
at the base of vertical conduit runs and equipment enclosures, and will build up over a period of time. This can
be detrimental to electronic devices. To eliminate this
condition, explosion-proof seals, drains and breathers
(such as Crouse-Hinds type ECD) should be installed to
automatically bleed off accumulated water.
The following steps should be used for mounting and
wiring the detectors:
1. Detectors should be located for the best unobstructed view of the area to be protected.
Detectors must be accessible for cleaning the window and reflector rings.
The blinded detector module should be mounted
as close as or closer than the fire detector module
to the source of radioactivity. For outdoor applications, fire detectors should be aimed downward to
prevent the cone of vision from scanning the horizon, because the detectors could respond to long
duration lightning flashes. If the detectors are not
pointed straight down, they should be mounted
with the UV test lamp of the fire detector module at
the module’s highest point, if feasible. Otherwise,
dirt accumulation between the window and the
reflector ring might interfere with the Automatic
o
i
function. See Figure 10 for mounting dimensions.
2. Disassemble the detector enclosures by turning
the housing covers counterclockwise. See Figure
2 for an example of the detector assemblies.
3. Connect the terminal cap to the conduit or the
optional swivel mounting bracket so that the wires
from the controller can be installed and trimmed.
4. Connect A-, B-, and D-leads to connections in terminal block.
13 95-8256
Connect the B-lead shields to connector C in the terminal block. All A-leads go to the A-lead connection in the
terminal block. If one C7051 is used, its fire detector
module is connected to zone 1 B-lead and D-lead inputs,
and its blinded detector module is connected to zone 5
B-lead and D-lead inputs. A second C7051’s fire and
blinded detector module would be connected to zones 2
and 6 respectively. Zones 1 to 4 on the backplate connect to fire detector modules. Zones 5 to 8 connect to
blinded surveillance detector modules. Up to four
C7051s can be connected to one R7404.
NOTE
If the wires from individual detectors are connected to the R7404 Controller in a multiple conductor cable, it is necessary to arrange them as
shown in Figure 11 to prevent “cross-talk.” The
individual B-leads should be arranged around the
outside of the cable with a ground lead between.
The inner layer of conductors should be the Dleads with the common A-lead in the center.
These instructions apply for installations using
from two to four detectors.
5. Remove matched UV sensor tube modules from
shipping package and place into position on blinded and fire detector terminal blocks, locating the
correct terminal position by observing the index
pin. Avoid touching the exposed glass envelopes
of the tubes, since oil from fingerprints can absorb
UV and reduce the tube’s sensitivity.
NOTE
Use only specially matched pairs of DE1888G2
tube modules in R7404/C7051 systems.
6. Install four screws on each detector and tighten.
7. On blinded detector module, slide
o
i
reflector cap
over barrel of sensor tube module until firmly seated. Make certain semicircular opening is centered
exactly over source tube on sensor tube module.
8. Replace detector housings. Black anodized barrel
is screwed onto blinded detector module. Red
barrel is screwed onto fire detector module.
9. Thoroughly clean the fire detector window and the
reflective ring. Det-Tronics window cleaner solution
is specially designed for this application. Many of
the commercial cleaners leave a residue on the
surface that absorbs UV radiation. Clean the window out to the edge. After cleaning, re-install the
ring so the split is 180 degrees from the
o
i
test
lamp (opening down to prevent water buildup).
Hold the ring by the tabs, being careful not to leave
fingerprints on the reflective surface.
NOTE
Use a clean cloth for cleaning. DO NOT use
commercial glass cleaning tissues since many of
these contain a silicone substance, which
remains on the cleaned surface and will absorb
UV radiation.
SWITCH SETTING PROCEDURE
It is essential that the controllers are properly programmed at the time of installation. There are three rocker switch assemblies on the left side of each controller
that are used to select detectors, controller sensitivity,
fire logic (voting), output latching and time delay.
Figure 12 illustrates the left side of the R7404 Controller
and contains a short explanation of rocker switch usage.
14
Figure 11—Wire Arrangement in a Multiple Conductor Cable
DETECTOR 1
DETECTOR 2
DETECTOR 3
DETECTOR 4
A
B
C
D
A
B
C
D
G
A
B
C
D
A
B
C
D
G
B1
D1
B2
B4
D4
A
D2
G
G
D3
B3
1. Detectors Connected — Switch Assembly Rockers
1-1 to 1-4. Each zone can have one detector for a
maximum of four detectors in four zones connected to one controller. (The word “detector” denotes
the C7051, which comprises two detector modules,
in this context.) Switch assembly rockers 1-1
through 1-4 are used to enable the detector of
each zone. The appropriate rocker must be set to
the “Open” position for each detector connected.
Care must be taken when setting these rockers. If
a rocker is set open, but no detector is connected
in that location , the controller will show a “2-fault”
on the lower digital display and the ZONE display
will show which zone is set incorrectly. If a rocker
is set closed, but a detector is connected, the controller performs normally, but that detector is eliminated from the Automatic
o
i
test sequence, and
any faults that may occur in its circuit would not be
automatically identified. This condition can be
found only when performing the manual
o
i
test procedure. See the “Troubleshooting” section. Figure
13 is an example of switch settings for a controller
using three detectors.
2. Switch Assembly Rockers 2-1 to 2-8 are not used.
3. Controller Sensitivity Adjustment — Switch
Assembly Rockers 3-1 to 3-4 are used to set (program) controller sensitivity in 8 cps increments.
3-1 closed - 8 cps
3-2 closed - 16 cps
3-3 closed - 32 cps
3-4 closed - 64 cps
Sensitivity = cumulative value of rockers set closed
These rockers may be set in any combination to
give the sensitivity setting selected for the application, up to 120 cps.
15 95-8256
SWITCH ASSEMBLY 1
Figure 12—Controller Rocker Switches
Figure 13—Detector Selection
DETECTOR PAIR SELECTION
ROCKER 1-4 OPEN:
ZONES 4 AND 8 SELECTED
ROCKER 1-3 OPEN:
ZONES 3 AND 7 SELECTED
ROCKER 1-2 OPEN:
ZONES 2 AND 6 SELECTED
ROCKER 1-1 OPEN:
ZONES 1 AND 5 SELECTED
SWITCH ASSEMBLY 2
NOT USED
SWITCH ASSEMBLY 4
TIME DELAY AND
LATCHING/NON-LATCHING OUTPUTS
ROCKER 8 – NOT USED
ROCKER 7 – NOT USED
ROCKER 6 – 4 SECOND DELAY
ROCKER 5 – 2 SECOND DELAY
ROCKER 4 – 1 SECOND DELAY
ROCKER 3 – 0.5 SECOND DELAY
ROCKER 2 – 0.25 SECOND DELAY
(ALL SWITCHES OPEN,
TIME DELAY = 0.5 SECOND)
ROCKER 1 – LATCHING OUTPUTS
WHEN ROCKER IS OPEN
ROCKER POSITIONS
CLOSED OPEN
8
7
6
DOT INDICATES ROCKER DEPRESSED
SWITCH ROCKER NUMBERS ARE DESIGNATED 1-1, 1-2, 1-3, ETC.
NOTE:
THE NUMBER PRECEDING THE DASH INDICATES THE SWITCH NUMBER.
THE NUMBER FOLLOWING THE DASH INDICATES THE ROCKER NUMBER
OF THE SWITCH INDICATED.
OPEN
8
7
OPEN
6
SWITCH ASSEMBLY 3
MASTER/SLAVE SELECTION
ROCKER SWITCH 3-8 OPEN:
SLAVE – ALL SURVEILLANCE
CONTROLLERS EXCEPT
FIRST IN SERIES
ROCKER SWITCH 3-8 CLOSED:
MASTER – FIRST SURVEILLANCE
CONTROLLER IN SERIES
FIRE LOGIC SETTING
ROCKER POSITION
3-6
3-7
ALL OPEN
1 CLOSED
2 CLOSED
3 CLOSED
SENSITIVITY SELECTION
ROCKER 3-4 CLOSED = 64 CPS
ROCKER 3-3 CLOSED = 32 CPS
ROCKER 3-2 CLOSED = 16 CPS
ROCKER 3-1 CLOSED = 8 CPS
OR ROCKER 3-1 CLOSED = 8 CPS)
THESE ROCKERS MAY BE USED
IN ANY COMBINATION FOR 8 CPS TO 120 CPS
FIRE LOGIC OUTPUTS
3-5
ON (FOR 1 OF 4 ZONES)
ON (FOR 2 OF 4 ZONES)
ON (FOR 3 OF 4 ZONES)
ON (FOR 4 OF 4 ZONES)
(ALL ROCKERS OPEN
DETECTORS
FIRE INPUT 3
C7051
BLIND
FIRE INPUT 2
C7051
BLIND
FIRE INPUT 1
C7051
BLIND
INPUT 7
INPUT 6
INPUT 5
NOT USED
SWITCH OPEN = DETECTOR SELECTED
8
7
6
{
5
4
3
2
1
INPUTS 1 - 3 (FIRE) AND
5 - 7 (RADIATION) SELECTED
OPEN
SWITCH 1
NOTE
If no rockers are closed, or if only rocker 3-1 is
closed, the controller responds to an 8 cps signal
from the detector.
Figure 14 is an example of a 24 cps setting.
4. Fire Logic Voting Criteria — Switch Assembly
Rockers 3-5 to 3-7, Rockers 3-5, 3-6 and 3-7 select
the voting requirements, which are Fire Logic A
and B common (4 zones voting).
NOTE
When the outputs are set for non-latching operation, the voting process will actuate the Fire Logic
outputs only if the preselected number of voting
zones “see” fire at the same time. When the outputs are set for latching operation, the voting
process will actuate the Fire Logic outputs when
voting criteria have been met, even if fire is not
being seen by each voting zone at the same time.
Zones 5 through 8 do not latch.
— Rockers 3-5, 3-6 and 3-7 open - one of four zones is
required for actuation.
— Rocker 3-5 closed, rockers 3-6 and 3-7 open - two of
four zones are required for actuation.
— Rockers 3-5 and 3-6 closed, rocker 3-7 open - three
of four zones are required for actuation.
— Rockers 3-5, 3-6 and 3-7 closed - four of four zones
are required for actuation.
In the example illustrated in Figure 15 the setting is for
three of four zones voting.
Switch 3-8 selects master or slave operation for the controller.
Closed = master, Open = slave.
5. Outputs Latching/Non-Latching - Switch Assembly
Rocker 4-1.
Closed = Non-Latching
Open = Latching
NOTE
The zone and fire logic outputs will latch when
turned on if rocker 4-1 is set open.
The outputs are de-latched by placing keylock
switch in RESET position or by actuating the
External Inhibit input. Figure 16 shows the setting
for selecting latching outputs.
6. Time Delay — Switch Assembly Rockers 4-2, 4-3,
4-4, 4-5 and 4-6. The time delay switches have the
following values.
Rocker 4-2 0.25 second
Rocker 4-3 0.5 second
Rocker 4-4 1.0 second
Rocker 4-5 2.0 seconds
Rocker 4-6 4.0 seconds
The total time delay is the added value of the rockers in the closed position plus 0.5 second.
Rockers can be closed in any arrangement for a
time delay of 0.5 to 8.25 seconds in 0.25 second
intervals.
Figure 17 shows the switch setting for a time delay
of 3.5 seconds.
16
Figure 14—Controller Sensitivity Selection
Figure 15—Fire Logic Voting Selection
Figure 16—Latching/Non-Latching Output Selection
Figure 17—Time Delay Selection
4
SWITCH 3
3
2
OPEN
1
3-1 CLOSED = 8 CPS
3-2 CLOSED = 16 CPS
TOTAL SENSITIVITY = 24 CPS
A0281
SWITCH 4
1
OUTPUTS LATCHED
OPEN
SWITCH 4
8
SWITCH 3
7
6
5
3 OF 4 ZONES VOTING
OPEN
8
7
6
5
4
3
2
NOTE: THE VALUE OF ROCKERS SET IN THE CLOSED POSITION ARE ADDITIVE.
NOT USED
}
4 SECOND TIME DELAY
2 SECOND TIME DELAY
OPEN
1 SECOND TIME DELAY
0.5 SECOND TIME DELAY
0.25 SECOND TIME DELAY
ROCKER 5 CLOSED = 2 SECONDS
ROCKER 4 CLOSED = 1 SECOND
TOTAL TIME DELAY = 3.5 SECONDS
It is inadvisable to use the minimum time delay (0.5
second) with the maximum detector sensitivity (8
cps), as this setting increases the possibility of
false system actuation.
CONTROLLER ELECTRICAL CONNECTIONS
All electrical connections are made to the plug-in field
wiring connector that is furnished with the controller.
Figure 18 shows its terminal configuration. Table 2 lists
the terminal connections and a brief description of their
usage.
Up to four detectors in four separate zones can be connected to the controller. Terminals A, B and D on the
detectors must be connected to the appropriate A, B
and D terminals at the R7404 Controller. Connect the
shield of the B-lead to terminal C in the detector and the
other end to circuit ground (terminal 2) at the controller
(see Figures 18 and 19). Terminal D in each detector
connects directly to individual terminals 12 through 19 on
the controller.
17 95-8256
Figure 18—R7404 Nuclear Surveillance Controller
Terminal Configuration
Electrical
Te rminals
Description
1 and 2 Input power: +10 to +38 vdc (1 to positive, 2
to circuit ground).
3 A-lead: (+290 vdc) connected to all detectors.
4 through 11 B-lead: input from each detector.
12 through 19 D- lead: oi driver to each detector.
20 through 27 Data Bus terminals - data transfer outputs,
connected to the data input bus of the (next)
surveillance controller in the series.
28 through 32 DMA (direct memory access) and data strobe
terminals. DMA IN (terminal 30) is connected
to the data sync output of the last surveillance
controller in the series.
33 through 36 Solid State Zone Outputs: correspond to four
fire zones (reference to ground - terminal 2).
NOTE: All R7404 solid state outputs are rated
100 ma at 0.5 volt when “on” (low state). The
outputs are high impedance (open collector,
100K ohm) when “off” (high state). Only the
Fault output is normally “on.”
37, 38 Not used.
39 Low level alarm output – count rate has
exceeded 50% of sensitivity setting.
40 Solid state “lockout” output – activated by con-
troller to indicate saturation lockout condition.
41 Solid State Fire Logic output – see “Theory of
Operation.”
42 Data Sync output – connects to DMA IN of
slave controller.
43 Solid State Alarm output – activated whenever
any zone output is activated. It is a latching
output and can be deactivated by depressing
the TEST/ACCEPT button or by activating the
external accept input (see below).
44 External Inhibit (input) – when activated, resets
the controller and disables fire response outputs. Input is activated when shorted to
ground (-V, terminal 2).
45 Solid State Outputs Inhibited (output) – is acti-
vated when fire response outputs are disabled.
46 Solid State Fault output – Normally “on” (low
voltage - logic 1), turned off by controller to
indicate a fault status.
47 External Accept (input) provides a means to
deactivate the alarm output. Input is activated
when shorted to ground.
48 through 55 Solid State Status and Detector outputs – pro-
vide binary representations of the front panel
digital displays for zone and status identification. Tables 3 and 4 list the identification
codes and the logic states of the “Fault” and
“Outputs Inhibited” bits for the various status
conditions.
56 through 63 Data Bus terminals – data transfer inputs, con-
nected to the data output bus of the last surveillance controller in the series.
64
Chassis (earth) ground – should be connected
to circuit ground (terminal 2) through a 0.47 µF
400 Volt non-polarized capacitor (not supplied).
Table 2—Nuclear Surveillance Controller Terminal Connections
J1
1
+
10 TO 38 VDC
}
–
2
(A) +290 VDC
3
B - INPUT 1
4
B - INPUT 2
5
B - INPUT 3
6
B - INPUT 4
7
B - INPUT 5
8
B - INPUT 6
9
B - INPUT 7
10
B - INPUT 8
11
DRIVER
D1-1 o
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
i
DRIVER
D1-2 o
i
DRIVER
D1-3 o
i
DRIVER
D1-4 o
i
DRIVER
D1-5 o
i
DRIVER
D1-6 o
i
DRIVER
D1-7 o
i
DRIVER
D1-8 o
i
DATA OUTPUT 0
DATA OUTPUT 1
DATA OUTPUT 2
DATA OUTPUT 3
DATA OUTPUT 4
DATA OUTPUT 5
DATA OUTPUT 6
DATA OUTPUT 7
DMA OUT AVAILABLE
DMA OUT
DMA IN
DATA STROBE
DMA IN AVAILABLE
R7404
ZONE OUTPUT 1
ZONE OUTPUT 2
ZONE OUTPUT 3
ZONE OUTPUT 4
LOW LEVEL ALARM
LOCKOUT OUTPUT
ALARM OUTPUT
EXTERNAL INHIBIT
OUTPUTS INHIBITED
FAULT OUTPUT
EXTERNAL ACCEPT
STATUS & DET. OUTPUT S1
STATUS & DET. OUTPUT S2
STATUS & DET. OUTPUT S3
STATUS & DET. OUTPUT S4
STATUS & DET. OUTPUT S5
STATUS & DET. OUTPUT S6
STATUS & DET. OUTPUT S7
STATUS & DET. OUTPUT S8
CHASSIS (EARTH) GND
NOT USED
NOT USED
FIRE LOGIC
DATA SYNC
DATA BUS 0
DATA BUS 1
DATA BUS 2
DATA BUS 3
DATA BUS 4
DATA BUS 5
DATA BUS 6
DATA BUS 7
J2
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
TYPICAL SYSTEM APPLICATION
The following application is an example only. For assistance in adapting a system to your individual requirements, contact Application Engineering at Detector
Electronics.
The system illustrated in Figure 19 incorporates two controllers that monitor eight detectors.
STARTUP PROCEDURE
CAUTION
Secure output loads before startup as described
in the “Manual Check in Normal Mode” subsection of the “Checkout Procedure.”
1. After setting the selection switches and making all
electrical connections, make sure that power is off
and plug controllers into connectors.
2. Turn on power and go through checkout procedures.
3. If the controllers appear to be operating normally,
remove mechanical blocking devices and restore
power to the extinguishing loads.
CHECKOUT PROCEDURE
MANUAL CHECK OF OPTICAL INTEGRITY
1. Place keylock switch in TEST position.
2. FAULT LED turns on.
3. INHIBIT LED turns on.
4. ZONE display indicates the zone selected.
DETECTOR display shows a “0”.
5. STATUS display indicates a “1”. (If any other number appears, see “Troubleshooting” section.)
6. Push and hold TEST/ACCEPT button. If the lens is
clean, a ZONE OUTPUT LED flashes to indicate the
zone of the detector being tested (after time delay).
7. Appropriate FIRE LOGIC LEDs are turned on if voting requirements are met.
(Surveillance zones 5-8 are not voted on and will
not turn on FIRE LOGIC LEDs).
8. Release TEST/ACCEPT button, ZONE OUTPUT
LED remains on steady.
9. Push SELECT button. Controller sequences to the
next lower numbered zone.
10.Repeat steps 6 through 10 until all detectors have
been checked.
18
Zone
Status Outputs
S1 S2 S3 S4
11000
20100
31100
40010
51010
60110
71110
80001
Table 3—Relationship of ZONE Display to the
Status Outputs
Table 4—Relationship of SYSTEM STATUS Display
to Status Outputs
Front Panel Display
Status Outputs
Outputs
System Status S5 S6 S7 S8 Fault
Inhibited
0 0000 0 1
1 0100 0 1
2 0010 0 0
3 0110 x*** 0
4 0001 0 0
5 0101 0 0
6* 0011 1 0
7** 0 1 1 1 1 0
80 or 1 0 0 0 0 1
9 1100 0 1
Status Outputs Logic 0 = 100k ohms to ground (0 volts)
S1 – S8, Fault Logic 1 = Less than 25 ohms to ground
Outputs Inhibited (0 volts)
Fire Zones only
Surveillance Zones only
1 on Fire Zones, 0 on Surveillance Zones
*
**
***
19 95-8256
202122
Figure 19—Typical System Application
33343536373839404142434445464748495051525354555657585960616263
J2
NOT USED
NOT USED
ZONE OUTPUT 1
ZONE OUTPUT 2
ZONE OUTPUT 3
ZONE OUTPUT 4
SLAVE CONTROLLER
10 TO 38 VDC
}
+
–
(A) +290 VDC
B - INPUT 1
B - INPUT 2
B - INPUT 3
123456789
J1
A
B1B2B3B4B5B6B7B8D1D2D3D4D5D6D7
FIRE LOGIC
DATA SYNC
LOCKOUT OUTPUT
LOW LEVEL ALARM
B - INPUT 4
B - INPUT 5
ALARM OUTPUT
B - INPUT 6
B - INPUT 7
B - INPUT 8
1011121314151617181920212223242526272829303132
FAULT OUTPUT
EXTERNAL INHIBIT
DRIVER
i
D1-1 o
EXTERNAL ACCEPT
OUTPUTS INHIBITED
STATUS & DET. OUTPUT S1
DRIVER
DRIVER
DRIVER
i
D1-3 o
i
D1-4 o
DRIVER
i
D1-5 o
i
D1-2 o
STATUS & DET. OUTPUT S2
STATUS & DET. OUTPUT S3
STATUS & DET. OUTPUT S4
STATUS & DET. OUTPUT S5
STATUS & DET. OUTPUT S6
STATUS & DET. OUTPUT S7
STATUS & DET. OUTPUT S8
DRIVER
DRIVER
DRIVER
i
i
i
D1-6 o
D1-7 o
D1-8 o
DATA OUTPUT 0
DATA OUTPUT 1
DATA OUTPUT 2
DATA OUTPUT 3
D8
DATA BUS 0
DATA OUTPUT 4
23
24
DATA BUS 1
DATA BUS 2
DATA BUS 3
DATA BUS 4
DATA OUTPUT 5
DATA OUTPUT 6
DATA OUTPUT 7
DMA OUT AVAILABLE
27
25
26
DATA BUS 5
DATA BUS 6
DATA BUS 7
DMA OUT
DMA IN
DATA STROBE
64
CAPACITOR
0.47 µF/400 V
CHASSIS (EARTH) GND
DMA IN AVAILABLE
4
3
AB1C
*
12
D1
8
*
3
AB5C
C7051
33343536373839404142434445464748495051525354555657585960616263
J2
ZONE OUTPUT 1
MASTER CONTROLLER
+
123456789
J1
16
D5
ZONE OUTPUT 2
ZONE OUTPUT 3
10 TO 38 VDC
}
–
(A) +290 VDC
A
*
5
3
AB2C
ZONE OUTPUT 4
B - INPUT 1
B1B2B3B4B5B6B7B8D1D2D3D4D5D6D7
13
D2
NOT USED
NOT USED
LOW LEVEL ALARM
B - INPUT 2
B - INPUT 3
B - INPUT 4
C7051
LOCKOUT OUTPUT
B - INPUT 5
*
9
3
AB6C
FIRE LOGIC
B - INPUT 6
17
D6
DATA SYNC
ALARM OUTPUT
EXTERNAL INHIBIT
OUTPUTS INHIBITED
DRIVER
DRIVER
i
i
B - INPUT 7
B - INPUT 8
D1-1 o
D1-2 o
1011121314151617181920212223242526272829303132
*
6
3
AB3C
FAULT OUTPUT
DRIVER
i
D1-3 o
14
D3
C7051
EXTERNAL ACCEPT
STATUS & DET. OUTPUT S1
STATUS & DET. OUTPUT S2
STATUS & DET. OUTPUT S3
DRIVER
DRIVER
DRIVER
i
D1-5 o
i
D1-6 o
DRIVER
i
D1-7 o
i
D1-4 o
*
3
10
18
AB7C
STATUS & DET. OUTPUT S4
DRIVER
i
D1-8 o
D8
D7
STATUS & DET. OUTPUT S5
STATUS & DET. OUTPUT S6
STATUS & DET. OUTPUT S7
STATUS & DET. OUTPUT S8
DATA OUTPUT 0
DATA OUTPUT 1
DATA OUTPUT 2
DATA OUTPUT 3
56575859606162
*
3
7
AB4C
DATA BUS 0
DATA BUS 1
DATA BUS 2
DATA OUTPUT 4
DATA OUTPUT 5
DATA OUTPUT 6
3
*
15
D4
DATA BUS 3
DATA OUTPUT 7
63
11
AB8C
C7051
DATA BUS 4
DATA BUS 5
DATA BUS 6
DATA BUS 7
DMA OUT AVAILABLE
DMA OUT
DMA IN
DATA STROBE
19
D8
CAPACITOR
0.47 µF/400 V
64
CHASSIS (EARTH) GND
DMA IN AVAILABLE
3
4
AB1C
*
12
D1
C7051
3
8
AB5C
*
16
D5
3
5
AB2C
*
13
D2
C7051
9
3
AB6C
*
17
D6
3
6
AB3C
*
14
D3
C7051
3
10
AB7C
*
18
D7
7
3
AB4C
*
15
D4
C7051
3
11
AB8C
*
19
D8
*ALL "C" LEADS ARE CONNECTED TO CONTROLLER
GROUND VIA CABLE SHIELD
TESTING OF DETECTOR MODULE RESPONSE TO
UV RADIATION (COUNT MODE TEST)
1. Place keylock switch in TEST position.
2. SYSTEM STATUS displays the number “1”.
3. ZONE display shows the zone that is electrically
positioned for testing.
4. Press and release SELECT and TEST/ACCEPT buttons simultaneously.
5. SYSTEM STATUS display changes to an “8”.
6. Press and hold TEST/ACCEPT button.
7. UV source tube (in detector housing of the module
under test) turns on.
8. Upper displays indicate the discharge rate of the
sensor under test (in cps). If FIRE LOGIC LEDs
turn on, multiply displayed count by 10. Count
rate should be between 50 and 300 cps. If not,
clean the window (fire detector module) and the
metal
o
i
reflector ring. If count rate does not fall
within the 50 to 300 cps range after cleaning,
and the
o
i
ring shows no signs of deterioration,
replace the sensor tube module. Record count
reading in the Recommended Test Form (inside
back cover).
9. Release TEST/ACCEPT button.
10.Upper displays now indicate quiescent state of
detector tube. Count should be between 00 and
05. If higher, place an obstruction over the detector window. If the count rate returns to the 00 to 05
range, the detector has been responding to external radiation. Check area for external source of UV
radiation, and either remove it or shield the detector from it. If none can be found, use cardboard to
cover the windows of the detectors in the zone
being tested. If the high count rate continues after
the detector window is covered, this indicates a
faulty module, and it must be replaced. If other
detectors in the vicinity exhibit similar symptoms,
the presence of x-rays or gamma radiation is indicated.
11.To test the next detector, press and release the
SELECT button.
12.ZONE display shows zone just tested.
13.Press and release the SELECT button again.
14.Controller cycles to next lower zone pair (controller
cycles through the detectors selected on rocker
switches 1-1 to 1-4). (See “Theory of Operation.”)
15.Repeat steps 6 through 14 until all detectors have
been checked. At the completion of the sequence,
each detector will have been tested for the following conditions:
A. Influence of background radiation, if any.
B. UV transmission capability of all optical surfaces
(where applicable).
C. Calibration of UV source/UV detector (these ele-
ments are factory adjusted, but are subject to
influences that may affect the calibration).
D. If the system is to be tested for response to an
actual fire, the exact response of each detector
can be measured. If any improvements in system
layout are needed, they will be revealed in this
way.
16.After completion of all tests, return keylock switch
to NORMAL position. System resets and both digital displays should become blank.
NOTE
The Automatic
o
i
system continuously monitors
the operation of the R7404 but does not monitor
external relays or equipment that may be operated from the fire signal outputs, the alarm signal
output or the fault signal output. It is important
that the system be manually checked using the
Normal Mode Checkout Procedure on a regular
basis. The whole system (including external
equipment) should be checked periodically using
the W8066 UV Test Lamp or an equivalent UV
source to simulate a fire.
MANUAL CHECK IN NORMAL MODE
The whole system should be periodically checked with
the W8066 UV Test Lamp or an equivalent UV source to
make sure that the detectors are not obstructed, that the
area “seen” by the detector has not changed, and that
there is no fault in the o
i
circuit.
CAUTION
Secure output loads (remove power from valves,
relays, igniters or other devices which would normally be actuated by the UV system) before performing the following test.
20
1. Place the keylock switch in the NORMAL position.
2. Turn on W8066 UV Test Lamp or an equivalent UV
source and shine into any fire detector.
3. If system works correctly, the appropriate ZONE
OUTPUT LED turns on and flashes, indicating the
zone in which the detector is located. ZONE display shows first zone activated. STATUS display
shows a “6”.
4. The FIRE LOGIC LEDs turn on if voting requirements are met.
5. Turn off the UV source.
6. FIRE LOGIC LEDs stay on if turned on in step 4.
7. The ZONE OUTPUT LED stays on but stops flashing. The numeral indicating the first zone that
responded to the UV signal is held in the ZONE
display, and the numeral “6” remains in the STATUS
display.
8. Repeat steps 2 through 5 for each detector in the
system.
9. After all detectors have been checked, reset the
system by turning the keylock switch to the RESET
position. Then turn it to the NORMAL position.
Display turns off. INHIBIT LED turns off. FAULT
LED turns off.
10.Restore power to output loads or remove any
mechanical blocking devices.
TROUBLESHOOTING
The Automatic Fault Identification circuitry, in conjunction
with the Automatic o
i
feature, continuously monitors the
status of the controller and all detectors. In the event of
a system malfunction, the microprocessor immediately
branches to an automatic fault identification program. If
a fault occurs, the FAULT LED will turn on. If the fault is
in the detector or wiring, the ZONE display will indicate
which zone has the fault. The STATUS display will indicate by code number the type of fault. If the fault is in
the microprocessor circuitry, the displays will remain
blank but the FAULT LED will turn on. See Table 5 for a
detailed explanation of the status/fault code numbers on
the lower digital display and the corresponding identification numbers on the upper digital display.
NOTE
Record all faults on the Fault Record Sheet at the
back of this manual.
VOLTAGES AND WAVEFORMS TO AID IN
TROUBLESHOOTING
A-lead (terminal 3) to circuit ground: +290 vdc.
D-lead (terminals 12 through 19) to A-lead: less than 1
volt.
Do not check in normal mode. System must be in test
mode to prevent false actuation. In the test mode, man-
ual o
i
operation can be verified by observing the voltage
between the D-lead and circuit ground.
Due to the meter “loading” factor, the voltage from the Dlead to ground measures approximately +260 vdc.
When the test button is depressed (in test mode) the voltage on the D-lead of the detector under test drops to 0.5
vdc or less (see Figure 20).
B-lead (terminals 4 through 11): The manual o
i
test
causes the detector to send a series of voltage pulses to
the controller. The waveform on the B-lead of the detector under test is illustrated in Figure 21.
SOLID STATE INPUT AND OUTPUT CIRCUITRY
Figures 22 and 23 illustrate the input and output drive circuitry of the R7404 Controller.
ORDERING INFORMATION
When ordering specify:
Model R7404 Fire Protection and Nuclear Surveillance
Controller
Model C7051 Detector
Number of C7051 Detectors and R7404 Controllers
ACCESSORIES
— Q4004 Mounting Cage. Cage accommodates up
to eight modules. It is designed to fit a standard 19
inch instrument rack. See form 95-8241 for details.
— Filler panels (part number 002188-001). For empty
positions in the Q4004 Cage.
— W8066 Explosion-proof, portable UV Test Lamp.
See form 95-8345 for details.
— Matched pair, DE1888G2 sensor tubes (part num-
ber 003240-207), for replacement into C7051
Detector.
21 95-8256
DEVICE REPAIR
For devices or components in need of repair, contact
your local source or return the equipment transportation
prepaid to:
Detector Electronics Corporation
Returned Goods Department
6901 West 110th Street
Minneapolis, Minnesota 55438 U.S.A.
22
Upper Displays Lower Display
Description
Detector Zone Status
00 0 Keylock switch is in RESET position, or the external inhibit is activated.
(Outputs inhibited, except Status outputs.)
01 - 8 1 Keylock switch is in TEST position. (Outputs inhibited, except Status outputs.)
01 - 8 2 oi fault - the oi ring and/or the window of the detector indicated in the upper ZONE
display is dirty, or the detector module has lost sensitivity, or there is an open wire
between the detector and the controller.
01 - 8 3 Zones 1-4: Count rate has exceeded 50% of sensitivity setting. A separate output
is activated, and no fault output is activated.
Zones 5-8: Runaway detector – fault output activated. (This can be checked by
using the count mode test of the controller as described in the “Checkout” section.)
00 4 Low +290 vdc caused by a shorted A-lead or controller malfunction.
00 5 High +290 vdc caused by a failure in the regulating network in the controller.
01 - 4 6 Fire Output signal - blinking ZONE OUTPUT LED indicates fire location. Steady
ZONE OUTPUT LED indicates that the detectors in that zone have responded to a
UV signal, but are no longer responding. This is not a fault condition.
01 - 8 7 Count Subtraction Lockout. Surveillance detector module or modules are discharg-
ing at their maximum rate and the controller is subtracting the maximum signal from
the fire detector module’s signal. The system is thus “saturated,” and effectively
“locked-out,” i.e. there will be no false actuation of the system due to interference
signals, but the system is incapable of responding if a fire should occur at this time.
A separate output is activated when the system enters “lock-out.”
01 - 8 8 Controller has been placed in “count” mode (see “Checkout” section). Pushing and
releasing both SELECT and TEST/ACCEPT buttons at the same time while the keylock switch is in the TEST position changes the lower display to a numeral “8” - the
count mode for checking the count rate of each zone.
Blank Blank 9 Data Link Failure – slave controller is not receiving data, or is receiving incorrect
data from the master controller.
Blank Blank Blank FAULT LED on. There is a problem in the R7404 microprocessor circuitry. Place key-
lock switch in RESET, push and release LAMP TEST pushbutton and return the keylock switch to NORMAL. If operation does not return to normal, replace the entire
unit. Make sure the new R7404 is programmed the same as the one being replaced.
Blank Blank Blank No LEDs on or displays on. Check input power to controller or blown fuse in con-
troller.
Table 5—Status Codes - Nuclear Surveillance Controller
23 95-8256
+260 VDC
Figure 20—Detector D-lead Voltage - Manual Test
Figure 21—Detector B-lead Waveform
Figure 22—R7404 Solid State Output Circuit
Figure 23—Solid State Input
Detector Electronics Corporation
6901 West 110th Street • Minneapolis, Minnesota 55438 • Fax (612) 829-8750
Telephone (612) 941-5665 or (800) 765-FIRE • www.detronics.com • email: detronics@detronics.com
–0 V
+ 40 V
5 to 10 mS
0 V
5 uS
TEST
BUTTON
PRESSED
TEST
BUTTON
RELEASED
+VDC
60 VOLT MAXIMUM
(MUST BE EXTERNALLY
PROVIDED)
LOAD
D
G
S
100 K Ω
OUTPUT CIRCUIT
+VDC
LOAD
SWITCH
100 K Ω
EQUIVALENT CIRCUIT
+VDC
10K
24
Fault Record Sheet
Upper Display Lower Display
Date Time
Detector Zone System Status
Operator Comments
25 95-8256
Recommended Test Form
Date Date Date Lens Sensitivity Readings
Remarks
Installed Checked Cleaned Count Test Mode
Loading...