Desa AMITY SDVBPD, AMITY SDVBND User Manual

CAST IRON STOVE AND DIRECT-VENT (FREESTANDING FIREPLACE HEATER) BURNER SYSTEM

OWNER’S OPERATION AND INSTALLATION MANUAL

For more information, visit www.desatech.com

SCIVFC/PSCIVFC

SERIES STOVE

"AMITY™"

VCIS/PVCIS

Series Stove

"OXFORD™"

NATURAL GAS BURNER SYSTEM MODEL SDVBND

PROPANE/LP GAS BURNER SYSTEM MODEL SDVBPD

REMOTE READY

IMPORTANT: This direct-vent burner system must be installed into approved cast iron

stove bodies, models SCIVFC/PSCIVFC/VCIS/PVCIS/VH series ONLY.

WARNING: If the information in this manual is not followed exactly, a fire or explosion may result causing property damage, personal injury, or loss of life.

FOR YOUR SAFETY Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this or any other appliance.

FOR YOUR SAFETY

WHAT TO DO IF YOU SMELL GAS

• Do not try to light any appliance.

• Do not touch any electrical switch

• Do not use any phone in your building.

• Immediately call your gas supplier from a neighbor’s

phone. Follow the gas supplier’s instructions.

• If you cannot reach your gas supplier, call the fire department.

VH series Stove

"VICTOR HEARTH™"

WARNING: Improper installation, adjustment, alteration, service, or maintenance can cause injury or property damage. Refer to this manual for correct installation and operational procedures. For assistance or additional information consult a qualified installer, service agency, or the gas supplier.

Installation and service must be performed by a qualified installer, service agency, or the gas supplier.

This appliance may be installed in an aftermarket*, permanently located, manufactured (mobile) home, where not prohibited by state or local codes.

This appliance is only for use with the type of gas indicated on the rating plate. This appliance is not convertible for use with other gases, unless a certified kit is used.

* Aftermarket: Completion of sale, not for purpose of resale, from the manufacturer.

Save this manual for future reference.

TABLE OF CONTENTS

SAFETY INFORMATION

TABLE OF CONTENTS

SAFETY INFORMATION ............................................................ 2

PRODUCT IDENTIFICATION ..................................................... 3

LOCAL CODES ........................................................................... 4

PRODUCT FEATURES .............................................................. 4

GLOSSARY OF TERMS ............................................................. 4

PRE-INSTALLATION PREPARATION ........................................ 4

CAST IRON STOVE AND DIRECT-VENT BURNER SYSTEM

ASSEMBLY ................................................................................. 5

GENERAL VENTING ................................................................ 10

VENTING INSTALLATION ........................................................ 12

STOVE AND DIRECT-VENT BURNER SYSTEM INSTALLATION .. 20

OPERATING STOVE WITH BURNER SYSTEM ...................... 26

INSPECTING BURNERS.......................................................... 28

CLEANING AND MAINTENANCE ............................................ 29

TROUBLESHOOTING .............................................................. 30

SPECIFICATIONS .................................................................... 33

WIRING DIAGRAM ................................................................... 33

REPLACEMENT PARTS .......................................................... 33

ILLUSTRATED PARTS BREAKDOWN AND PARTS LIST ....... 34

TECHNICAL SERVICE ............................................................. 38

SERVICE HINTS....................................................................... 38

ACCESSORIES ........................................................................ 38

OWNER'S REGISTRATION ..................................................... 39

WARRANTY INFORMATION ...................................... Back Cover

SAFETY INFORMATION

WARNINGS

WARNING: This product contains and/or generates chemicals known to the State of California to cause cancer or birth defects, or other reproductive harm.

IMPORTANT: Read this owner’s manual carefully and completely before trying to assemble, operate, or service this stove and burner system. Improper use of this stove and burner system can cause serious injury or death from burns, fire, explosions, electrical shock, and carbon monoxide poisoning.

DANGER: Carbon monoxide poisoning may lead to death!

This appliance complies with the current ANSI Z21.88 and CSA 2.33 as a Vented Gas Fireplace Heater and is listed and tested by the Canadian Standards Association to the above test standards. This stove with burner system is a vented product. This stove with burner system will not produce any gas leakage into your home if properly installed. This stove with burner system must be properly installed by a qualified service person. The glass door must be properly seated and sealed. If this unit is not properly installed by a qualified service person with glass door properly seated and sealed, gas leakage can occur.

Carbon Monoxide Poisoning: Early signs of carbon monoxide poison-

ing resemble the flu, with headaches, dizziness, or nausea. If you have these signs, the stove may not have been installed properly. Get fresh air at once! Have stove inspected and serviced by a qualified service person. Some people are more affected by carbon monoxide than others. These include pregnant women, people with heart or lung disease or anemia, those under the influence of alcohol, and those at high altitudes.

Natural and Propane/LP Gas: Natural and propane/LP gases are

both odorless. An odor-making agent is added to each of these gases. The odor helps you detect a gas leak. However, the odor added to these gases can fade. Gas may be present even though no odor exists.

Make certain you read and understand all warnings. Keep this manual for reference. It is your guide to safe and proper operation of this stove and burner system.

WARNING: Any change to this stove or burner

system or its controls can be dangerous.

1. This appliance is only for use with the type of gas indicated on the rating plate. This appliance is not convertible for use with other gases unless a certified kit is used.

2. For propane/LP burner system, do not place propane/LP supply tank(s) inside any structure. Locate propane/LP supply tank(s) outdoors. To prevent performance problems, do not use propane/ LP fuel tank of less than 100 lbs. capacity (propane/LP units only).

3. If you smell gas

• shut off gas supply

• do not try to light any appliance

• do not touch any electrical switch; do not use any phone in

your building

• immediately call your gas supplier from a neighbor’s phone.

Follow the gas supplier’s instructions

• if you cannot reach you gas supplier, call the fire department.

4. Never install the stove

• in a recreational vehicle

• where curtains, furniture, clothing, or other flammable ob-

jects are less than 42" from the front, top, or sides of the stove

• in high traffic areas

• in windy or drafty areas

5. This stove reaches high temperatures. Keep children and adults away from hot surfaces to avoid burns or clothing ignition. Stove will remain hot for a time after shutdown. Allow surfaces to cool before touching.

For more information, visit www.desatech.com

112126-01B

SAFETY INFORMATION

PRODUCT IDENTIFICATION

3 3

SAFETY INFORMATION

Continued

6. Carefully supervise young children when they are in the room with stove.

7. Do not modify the burner or stove under any circumstances. Any parts removed for servicing must be replaced prior to operating stove or burner system.

8. Turn burner system off and let cool before servicing, installing, or repairing. Only a qualified service person should install, service, or repair the stove or burner system. Have burner system inspected annually by a qualified service person.

9. You must keep control compartments, burners, and circulating air passages clean. More frequent cleaning may be needed due to excessive lint and dust from carpeting, bedding material, pet hair, etc. Turn off the gas valve and pilot light before cleaning stove or burner system.

10. Have venting system inspected annually by a qualified service person. If needed, have venting system cleaned or repaired. See Cleaning and Maintenance, page 29.

11. Keep the area around your stove clear of combustible materials, gasoline, and other flammable vapor and liquids. Do not run burner system where these are used or stored. Do not place items such as clothing or decorations on or around stove.

12. Do not use this stove to cook food or burn paper or other objects.

13. Never place anything on top of stove.

14. Do not use any solid fuels (wood, coal, paper, cardboard, etc.) in this stove. Use only the gas type indicated on burner system nameplate.

15. This appliance, when installed, must be electrically grounded in accordance with local codes or, in the absence of local codes, with the National Electrical Code, ANSI/NFPA 70, or the Ca- nadian Electrical Code, CSA C22.1.

16. Do not obstruct the flow of combustion and ventilation air in any way. Provide adequate clearances around air openings into the combustion chamber along with adequate accessibility clearance for servicing and proper operation.

17. Do not install stove directly on carpeting, vinyl tile, or any combustible material other than wood. The stove must set on a metal or wood panel extending the full width and depth of the stove.

18. Do not use stove or burner system if any part has been exposed to or under water. Immediately call a qualified service person to arrange for replacement of the unit.

19. Do not operate burner system if any log is broken.

20. Do not use a blower insert, heat exchanger insert, or other accessory not approved for use with this stove.

21. Do not operate burner system with glass door removed, cracked, or broken.

22. Provide adequate clearances to air openings.

PRODUCT IDENTIFICATION

Cast Iron Stove Body

Log Set

OUT

Piezo Ignitor

Vent Opening

Rear Cover

Pilot Assy

Blower with Adjustment Knob (Optional Installation)

Glowing Embers

Grate Assembly

Figure 1 - DESA Direct-Vent Burner System Shown Installed in Approved Cast Iron Stove Body (Oxford™ Model Shown)

Control Valve

Cast Iron Stove Body

Stove Front

Burner

Glass Door Assy

Lava Rock

112126-01B

For more information, visit www.desatech.com

LOCAL CODES

PRODUCT FEATURES GLOSSARY OF TERMS PRE-INSTALLATION PREPARATION

Location and Space Requirements

LOCAL CODES

Install and use stove and burner system with care. Follow all local codes. In the absence to local codes, use the current National Fuel

Gas Code ANSI Z223.1/NFPA 54* (USA) or the current CSAB149[.1 or .2] Installation Codes (Canada).

*Available from:

American National Standards Institute, Inc.

1430 Broadway

New York, NY 10018

National Fire Protection Association, Inc.

Batterymarch Park

Quincy, MA 02269

PRODUCT FEATURES

OPERATION

This cast iron stove with burner system is clean burning and vents easily through outside walls or vertically using outside air for combustion. Heat is generated by both realistic flames and glowing embers. When used without the blower accessory, the stove with burner system requires no electricity making it ideal for emergency backup heat.

PIEZO IGNITOR

This burner system has a piezo ignitor. This system requires no matches, batteries, or other sources to light burner system.

GLOSSARY OF TERMS

Chase - A box-like enclosure to protect venting from the elements

when the venting run is on the outside of a structure.

Mastic - A pliable sealant for use around the vent terminal.

Snorkel Termination - A box that raises the horizontal termination

above ground level clearances.

Vent Termination - Mounted on an outside wall or roof to separate

the inlet and outlet of the vent system and protect it from weather.

Vinyl Siding Standoff - A metal box that separates the vent cap from

vinyl siding.

Wall Thimble/Firestop - A metal plate used to secure the vent pipe

when it passes through a wall or ceiling.

PRE-INSTALLATION PREPARATION

WARNING: A qualified service person must in-

stall stove and burner system. Follow all local codes.

CAUTION: This stove creates warm air currents. These currents move heat to wall surfaces next to stove. Installing stove next to vinyl or cloth wall coverings or operating stove where impurities (such as, but not limited to, tobacco smoke, aromatic candles, cleaning fluids, oil or kerosene lamps, etc.) in the air exist, may discolor walls or cause odors.

LOCATION AND SPACE REQUIREMENTS

Determine the safest and most efficient location for your cast iron stove. Make sure that rafters and wall studs are not in the way of the venting system. Choose a location where the heat output is not affected by drafts, air conditioning ducts, windows, or doors. Figure 2 shows some common locations. Read all venting information in this manual. Be aware of all restrictions and precautions before deciding the exact location for your stove.

When deciding the location of your stove, follow these rules:

1. Do not connect this stove and burner system to a chimney flue serving a separate solid-fuel burning fireplace or appliance.

2. Due to high temperatures, do not locate this stove in high traffic areas or near furniture or draperies.

On Wall with

Horizontal Termination

On Wall with Vertical

Termination Through Ceiling

Corner Installation

Figure 2 - Common Stove Locations

For more information, visit www.desatech.com

112126-01B

CAST IRON STOVE AND DIRECT-VENT BURNER SYSTEM ASSEMBLY

PRE-INSTALLATION PREPARATION

Continued

3. Proper clearances must be maintained, see Figures 3 and 4.

4. This stove is a freestanding unit designed to set directly on the floor. If your stove is to be installed directly on carpeting, vinyl tile, or any combustible material other than wood, it must be installed on a metal or wood panel extending the full width and depth of the stove. See Figure 5.

Ceiling

PRE-INSTALLATION PREPARATION

Location and Space Requirements (Cont.)

Stove Body Assembly

26 1/4"

Front

/2"

5 5

42"

(106.68 cm)

36"

(91.44 cm)

from

Front

Floor

(15.24 cm)

29"

(73.66 cm)

(10.16 cm)

from

Back

Wall

Front

27"

(10.16 c

Figure 3 - Clearances for Standard Installation

Figure 5 - Stove With Burner System Bottom Dimensions

CAST IRON STOVE AND DIRECT-VENT BURNER SYSTEM ASSEMBLY

STOVE BODY ASSEMBLY

1. Lift off corrugated box enclosing stove body crating.

2. Remove all screws fastening the wood frame enclosure. Spread wood frame open and lift away from plastic-bagged stove body. The bottom pieces of pallet wood will remain bolted to the stove body.

3. Remove plastic bag from stove body.

4. Locate the product identification label on the carton and record the model number and 7 digit serial number in the space provided in the back of this owner’s manual. Retain this operation and installation manual for future reference and warranty.

5. Amity Only:Remove the six (6) bolts on the back stove panel with an adjustable wrench or a 10 mm socket. Discard the back panel and retain the bolts and washers to attach the rear cover provided with the burner system.

(10.16

cm)

Figure 4 - Clearance for Corner Installation

For more information, visit www.desatech.com

112126-01B

4" (10.16

Bolt

Back Stove Panel

cm)

Figure 6 - Removing Back Panel (Amity Stove Only)

CAST IRON STOVE AND DIRECT-VENT BURNER SYSTEM ASSEMBLY

Stove Body Assembly (Cont.)

CAST IRON STOVE AND DIRECT-VENT BURNER SYSTEM ASSEMBLY

Continued

6. Remove all contents from inside stove cavity. Contents include:

(1) - Stove bottom [Amity Only] (Discard - Not used with

this application)

(4) - Legs with leg leveler bolts (1) - Bottom door (3) - Top grates (1) - Hardware kit bag with fasteners

7. Carefully lay stove body on back to attach bottom components to stove body (see Figure 7). Rest stove on drop cloth or blanket to avoid scratching stove edges.

8. Remove remaining pallet wood attached to bottom of stove body (see Figure 8). Use an adjustable wrench to remove bolts.

9. Fasten each leg to stove with four (4) M8 x 1.25 - 20mm bolts. Use a flat washer and lock washer with each bolt. Tighten bolts into threaded holes on stove body (see Figures 9 and 10). Use an adjustable wrench or a 12mm and 6mm socket.

10. Attach stove door by inserting step bolt through door hinge pivot hole and into threaded hole in stove body (Figures 9 and 11). Use an adjustable wrench or a 12mm socket to fasten step bolt. Tighten step bolt until snug. Make sure door moves freely.

Top of Stove Unit

Top of

Stove

Unit

Front of Stove Unit

Drop Cloth/ Blanket

Front of Stove Unit

Pallet Wood Bolted to Bottom of Stove Body

11. Install door catch bolt (M8 x 1.25-55mm with two M8 hex nuts) into threaded hole on stove body (see Figure 9). Use an adjustable wrench or a 12mm socket. The catch bolt has two hex nuts attached to it (see Figure 12). The top nut is a bolt stop and the bottom nut is for door leveling adjustment.

Door Hinge Step Bolt Hole

Bottom of Stove Unit

Figure 9 - Locating Threaded Holes for Legs and Door Attachment

Washers

Bolt

Figure 10 - Attaching Stove Legs (Oxford™ Model Shown)

Front

Leg Hole

Door Catch Bolt With Adjustable Hex Nuts Hole

Bottom Of Stove Unit

Leg

Figure 7 - Laying Down Stove On Side

Front

Bolt

Pallet Wood

Figure 8 - Removing Pallet Wood From The Bottom of The Stove

For more information, visit www.desatech.com

Pallet Wood

Bottom Of Stove Unit

Stove Door

Door Hinge

Step Bolt

Bolt Shoulder

Figure 11 - Attaching Stove Door

Threaded Hole

Door

Door Claw

Catch Bolt

Figure 12 - Catch Bolt and Door Claw Orientation

Bolt Stop

Adjusting Nut

112126-01B

CAST IRON STOVE AND DIRECT-VENT BURNER SYSTEM ASSEMBLY

Continued

12. Check general catch bolt alignment with door claw. Make final adjustment and door leveling after stove is in normal standing position.

13. Carefully lift stove back up on its four attached legs.

Removing Front Surround Panel

Remove 2 bolts from bottom of stove and set aside. Remove bolt from the top of the stove to remove the front panel assembly (see Figure 13).

Stove Body

Front Assembly

Bolt

Installing Direct-Vent Burner System Into Stove Body

Front Surround Plate

Stove Body Assembly (Cont.)

Screws

Screw with Washer

Screen

Front Surround Plate and

Front Plate

Amity™ Model

Doors

Oxford™ and Victor Hearth™

Model

Figure 14 - Removing Screen from Front Assembly

7 7

Figure 13 - Removing Front Assembly (Oxford™ Model Shown)

Removing Screen (Optional)

Amity Models

1. Lay the front panel assembly face down on a protected surface. Remove the two screws that hold the front plate onto the front surround plate (see Figure 14). Save these screws.

2. Remove the screws and washers that hold the screen onto the front surround plate. Discard these screws, washers, and screen (see Figure 14).

3. Replace the two screws from step 1 to reassemble the front plate and the front surround plate. Set this assembly aside until burner system has been installed, logs have been placed inside of burner system, and glass door to burner system insert has been replaced.

Oxford or Victor Hearth Models

1. Lay the front panel assembly face down on a protected surface. Remove the screws and washers that hold the screen onto the front surround plate. Discard these screws, washers, and screen (see Figure 14).

2. Set this assembly aside until burner system has been installed, logs have been placed inside of burner system, and glass door to burner system insert has been replaced.

INSTALLING DIRECT-VENT BURNER SYSTEM INTO STOVE BODY

1. Carefully lift burner system and place into stove body from the rear of stove.

2. Place the left and right grate tops into the top of stove body. Discard center grate top of stove and replace with center grate top provided with burner system.

Right Top

Center Top Grate (Included with Burner System)

Left Top Grate

Figure 15 - Installing Burner System Into Cast Iron Stove Body

Grate

Cast Iron Stove Body

Burner System

112126-01B

For more information, visit www.desatech.com

CAST IRON STOVE AND DIRECT-VENT BURNER SYSTEM ASSEMBLY

Installing Optional Blower Accessory

CAST IRON STOVE AND DIRECT-VENT BURNER SYSTEM ASSEMBLY

Continued

INSTALLING OPTIONAL BLOWER ACCESSORY

NOTICE: If installing blower in an existing stove burner system with gas connections, shut off gas supply and disconnect heater from gas supply. Contact a qualified service person to do this.

INSTALLING THE BLOWER

1. Remove 4 hex screws securing rear cover to back of stove body (see Figure 16).

2. Separate bottom cover from rear cover by loosening the 8 mounting screws (see Figure 16).

3. Align the holes in the top mounting tabs of blower with the holes in wall of rear cover. Using the 4 screws provided, mount blower and tighten screws securely (see Figure 17).

Rear Cover

Hex Screws

Stove Body

Mounting Screws

Thermostat Blower Only: Attach thermal switch and bracket

4. to inside rear cover wall with two hex head screws provided as shown in Figure 17. After securing bracket to rear cover, carefully bend along existing bend line on bracket to almost a 90° angle (see Figure 17). This will allow thermal switch to be positioned against stove rear wall and sense temperature when in operating mode.

5. Place speed control on left inside of rear cover and push the plastic control shaft through opening (see Figure 17).

6. While supporting speed control, secure control shaft with lock nut by pushing and turning lock nut with pliers clockwise until tight against the side of rear cover. Place control knob provided onto shaft.

TOP VIEW

Thermal Switch and Bracket

Blower Control Knob

Locknut

Control Shaft

Speed Control

Hex Screws

Mounting Screws

Bottom Cover

Figure 16 - Removing Rear Cover and Bottom Cover from Stove Body

Mounting Screws

Screws

Mounting Holes

Blower Assembly

Figure 17 - Blower Assembly, Speed Control, and Thermal Switch Locations

Mounting Holes

For more information, visit www.desatech.com

112126-01B

CAST IRON STOVE AND DIRECT-VENT BURNER SYSTEM ASSEMBLY

Continued

7. Place the green ground wire between the bottom hole on the blower assembly and the hex screw and tighten (see Figure 18).

8. Connect the blue wire on the blower assembly to one side of the thermal switch (see Figure 18).

9. Connect the black wire to the other side of the thermal switch (see Figure 18).

10. Connect the white wire to the other terminal on the blower motor assembly (see Figure 18). Make sure the thermal switch has been properly installed to fit against back of fireplace insert after the rear cover assembly has been reinstalled.

11. Make sure all wire connections to terminals on blower motor and thermal switch are securely attached and that the screw retaining the green ground wire is tight.

12. Check to make sure that the power cord is completely clear of the blower wheel and that there are no foreign objects in blower wheel.

13. Peel off the backing paper and stick the supplied wiring diagram decal on the inside of rear cover as shown (see Figure 18).

WARNING: Never touch the blower wheel while in

operation.

Speed Control

Power Cord (Route Through Plastic Bushing in Bottom Cover When Assembled)

Installing Optional Blower Accessory (Cont.)

Installing Rear Cover

14. Reattach bottom cover to rear cover with 8 screws (see Figure 16, page 8). Make sure that you don’t pinch any wires during reassembly. Route power cord through plastic bushing in bottom of rear cover.

WARNING: Failure to position the parts in accordance with supplied diagrams or failure to use only parts specifically approved with this heater may result in damage or personal injury.

INSTALLING REAR COVER

1. Place rear cover behind stove body. Rear cover will rest on the bottom ledge of the stove body.

2. Using hex screws provided, attach rear cover to back of stove body. See Figure 19. securely in place before venting pipes are installed.

3. Open lower door panel. The valve is attached to the underside of the burner system assembly.

4. Connect or reconnect gas supply, see Connecting Stove/Burner System to Gas Supply on page 21.

WARNING: A qualified installer or service person must connect fireplace to gas supply. Follow all local codes.

IMPORTANT:

This rear cover must be

Black Wire

Thermal Switch

Wiring Diagram

Blue Wire

Screw

Green Ground Wire

Figure 18 - Blower Wiring Layout (Thermostat Blower Shown)

For more information, visit www.desatech.com

112126-01B

White Wire

Decal

Hex Screws

Rear Cover (Shown with Optional

Blower Power Cord

Figure 19 - Installing Rear Cover (Shown with Optional Blower Accessory)

Blower)

GENERAL VENTING

Location of Vent Termination

GENERAL VENTING

Your stove with burner system is approved to be vented either through the side wall, or vertically using the following guidelines:

• Use only venting components or kits specifically approved for use with this stove and burner system (see Parts Lists for Vent- ing Kits and Components, page 19).

IMPORTANT:

ent manufacturers.

• Minimum clearance between vent pipes and combustible materials is 1" (2.5 cm), except where stated otherwise.

• Do not recess venting terminations into a wall or siding.

• Install horizontal venting with a 1/4" rise for every 12" of run toward the termination.

• You may paint the vent termination with 450ºF (232ºC) heatresistant paint to coordinate with the exterior finish.

• There must not be any obstruction such as bushes, garden sheds, fences, decks, or utility buildings within 24" from the front of the termination cap.

• Do not locate termination cap where excessive snow or ice build up may occur. Be sure to clear vent termination area after snow falls to prevent accidental blockage of venting system. When using snow blowers, do not direct snow towards vent termination area.

• You must maintain minimum wall and ceiling clearances shown in Figures 3 and 4, page 5.

• If installing horizontal vent termination cap on an exterior wall with siding, you must us a vinyl siding standoff (see Figure 26, page 14).

Do not mix venting components made by differ-

LOCATION OF VENT TERMINATION

When locating vent termination, it is important to observe the minimum clearances shown in Figure 20, page 11.

*Check with local codes or with the current CAN/CSA B149[.1 or .2] Installation Codes for Canada or the USA Installations follow the current National Fuel Gas Code, ANSI Z223.1/NFPA 54.

For more information, visit www.desatech.com

112126-01B

GENERAL VENTING Continued

A = clearance above grade, veranda, porch, deck, or balcony

[*12 inches (30.5mc) minimum]

B = clearance to window or door that may be opened

[12 inches (30.5cm) minimum]

C = clearance to permanently closed window [minimum 12 inches

(30.5cm) recommended to prevent condensation on window]

D = vertical clearance to ventilated soffit located above the terminal

within a horizontal distance of 24 inches (61cm) from the

center-line of the terminal [18 inches (45.7cm) minimum] E = clearance to unventilated soffit [12 inches (30.5cm) minimum] F = clearance to outside corner (see below) G = clearance to inside corner (see below) H = *not to be installed above a meter/regulator assembly within

36 inches (91.4cm) horizontally from the center-line of the regulator

vent shall not terminate directly above a side-walk or paved driveway which is located between two single family dwellings and serves both dwellings* only permitted if veranda, porch, deck or balconey is fully open on a minimum of 2 sides beneath the floor*

* as specified in CAN/CSA B149 (.1 or .2) Installation Codes (1991) for Canada and U.S.A.

Note

: Local codes or regulations may require different clearances

Fixed

Closed

Openable

TERMINATION CAP

Openable

AIR SUPPLY INLET

GENERAL VENTING

Fixed

Closed

I = clearance to service regulator vent outlet [*72 inches (182.9cm)

minimum]

J = clearance to non-mechanical air supply inlet to building or the

combustion air inlet to any other fireplace [*12 inches (30.5cm) minimum]

K = clearance to a mechanical air supply inlet [*72 inches (182.9cm)

minimum]

L = clearance above paved side-walk or a paved driveway located on

public property [*84 inches (213.3cm) minimum] M = clearance under veranda, porch, deck [*12 inches (30.5cm) minimum ] N = clearance above a roof shall extend a minimum of 24 inches (61cm)

above the highest point when it passes through the roof surface and

any other obstruction within a horizontal distance of 18 inches (45.7cm)

GAS METER RESTRICTED AREA

(TERMINATION PROHIBITED)

11 11

Termination Clearances for Buildings with Combustible and Noncombustible Exteriors

Inside Corner

Balcony with No Side Wall

G = 12" (30.5cm) minimum clearance

A = 6" (15.2cm)

Outside Corner Recessed Location

B = 6" (15.2cm)

Balcony with Perpendicular Side Wall

Combustible & Noncombustible H = 24" (61cm) J = 20" (50.8cm)

Figure 20 - Minimum Clearances for Vent Terminations

For more information, visit www.desatech.com

112126-01B

C = Maximum depth of 48" (121.9cm) for

recessed location

D = Minimum width for back wall of

recessed location Combustible - 38" (965mm) Noncombustible - 24" (61cm)

E = Clearance from corner in

recessed locationCombustible - 6" (15.2cm) Noncombustible - 2" (5.1cm)

VENTING INSTALLATION

Installation Precautions Installation Planning

VENTING INSTALLATION

WARNING: Read all instructions completely and thoroughly before attempting installation. Failure to do so could result in serious injury, property damage or loss of life. Operation of improperly installed and maintained venting system could result in serious injury, property damage or loss of life.

NOTICE: Do not seal termination cap to pipe. Cap must be removable for servicing vent system.

NOTICE: Failure to follow these instructions will void the warranty.

INSTALLATION PRECAUTIONS

Consult local building codes before beginning the installation. The installer must make sure to select the proper vent system for installation. Before installing vent kit, the installer must read this stove and burner system manual and vent kit instructions.

Only a qualified service person should install venting system. The installer must follow these safety rules:

• Wear gloves and safety glasses for protection

• Use extreme caution when using ladders or when on roof tops

• Be aware of electrical wiring locations in walls and ceilings

The following actions will void the warranty on your venting system:

• Installation of any damaged venting component

• Unauthorized modification of the venting system

• Installation of any component part not manufactured or approved by DESA

• Installation other than as instructed by these instructions

WARNING: This stove with burner system and vent assembly must be vented directly to the outside. The venting system must NEVER be attached to a chimney serving a separate solid fuel burning appliance. Each gas appliance must use a separate vent system. Do not use common vent systems.

INSTALLATION PLANNING

There are two basic types of direct-vent installation:

• Horizontal Termination

• Vertical Termination

It is important to select the proper length of vent pipe for the type of termination you choose. It is also important to note the wall thickness.

For Horizontal Termination: Select the amount of vertical rise

desired. The horizontal run of venting must have 1/4" rise for every 12" of run towards the termination.

WARNING: Never run the vent pipe downward as this may cause excessive temperatures which could cause a fire.

You may use up to two 90° elbows on any single horizontal run of vent pipe in this configuration. See Horizontal Termination Configu- rations, and Figures 28 and 30 on page 15.

For Vertical Termination: Measure the distance from the burner

system flue outlet to the ceiling. Add the ceiling thickness, the vertical rise in an attic or second story, and allow for sufficient vent height above the roofline. You may use up to three 90° elbows, depending on venting configuration. See Vertical Termination Configurations on page 17.

Note:

You may use up to two 45° elbows in place of a 90° elbow.

You must follow rise to run ratios when using 45° elbows.

For two-story applications, firestops are required at each floor level (see Figure 32, page 16). If an offset is needed in the attic, additional pipe and elbows will be required.

You may use a chase with a vent termination with exposed pipe on the exterior of the house. See Installing Vent System in a Chase, page 13.

Your stove with direct-vent burner system has been tested for a maximum horizontal run of 20' with 8' vertical rise (see Installation for Horizontal Termination, page 13). The maximum vertical run is 40' (see Installation for Vertical Termination, page 16).

It is very important that the venting system maintain its balance between the combustion air intake and the flue gas exhaust. Certain limitations apply to vent configurations and must be strictly followed.

WARNING: Horizontal sections of this vent system require a minimum clearance of 2" from the top of the pipe and 1" minimum to the sides and bottom. Vertical sections of this system require a minimum of 1" clearance to combustible materials on all sides of the pipe.

For more information, visit www.desatech.com

112126-01B

VENTING INSTALLATION

Continued

Installing Vent System in a Chase

A chase is a vertical box-like structure built to enclose venting that runs along the outside of a building. A chase is not required for such venting.

NOTICE: Treatment of firestops and construction of the chase may vary from building type to building type. These instructions are not substitutes for the requirements of local building codes. You must follow all local building codes.

Note:

When installing in a chase, you should insulate the chase as

you would the outside walls of your home. This is especially important in cold climates. Minimum air space clearance between vent pipes and combustible materials and/or insulation is 1".

INSTALLATION FOR HORIZONTAL TERMINATION

VENTING INSTALLATION

Installation Planning (Cont.)

Installation for Horizontal Termination

Figure 21 - Snorkel Termination

Snorkel

12" Minimum

(30.5cm)

13 13

CAUTION: Horizontally terminated venting configurations require one foot of vertical rise from the 45° elbow before any horizontal run can be made. Failure to meet venting requirements may cause performance problems and possible damage to the fireplace.

1. Determine the route your horizontal venting will take. location of the horizontal vent termination on the exterior wall must meet all local and national building codes and must not be blocked or obstructed.

WARNING: Do not recess vent terminal into a wall

or siding.

Snorkel terminations are available for terminations requiring a vertical rise on the exterior of the building (see Figures 21 and

22). Snorkel kit VKS-47-K is also available (see page 19). Follow the same installation procedures used for standard horizontal termination with the exception of the external wall firestop. The snorkel termination does not require the use of the external wall firestop. If installing the snorkel termination below grade (basement applications), you must provide proper drainage to prevent water from entering the snorkel termination (see Figure

22). Do not back fill around the snorkel termination.

2. Vent pipes and fittings have special twist-lock connections. Assemble the desired combination of pipe and elbows to the appliance adaptor with pipe seams oriented towards the wall or floor.

Twist-lock Procedure: The female ends of the pipes and fittings

have four locking lugs (indentations). These lugs will slide straight into matching slots on the male ends of adjacent pipes and fittings. (All connections must be sealed with high temperature silicone sealant as specified in the second warning statement on page 12.) Push the pipe sections together and twist one section clockwise approximately one-quarter turn until the sections are fully locked. See Figure 23. every three feet. Use wall straps for this purpose.

Note:

Horizontal runs of vent must be supported

Note:

The

Snorkel

12" Minimum

(30.5cm)

Adequate drainage

Figure 22 - Snorkel Termination with Drainage Pipe

Female Locking Lugs

Male Slots

Vent Pipe

Figure 23 - Vent Pipe Connections

112126-01B

For more information, visit www.desatech.com

+ 29 hidden pages