Denver Orus 7000 Instructions For Use And Maintenance Manual

1

MOD :E-BIKE 7000
ENGLISH

Congratulations for purchasing this pedal assisted electric bicycle, carefully designed and manufactured by following the latest international
quality standards, including:

EN 14764-2005
EN 15194-2009

Please read this instruction manual carefully before use.
This manual contains important information on the safety and maintenance of the bicycle.
It is the purchaser’s responsibility to read this manual before use.

In the event that the original components should have production defects within the expiration of the warranty period, the manufacturer will
replace them. The warranty duration for electric bicycles is the following:

Frames and Forks: 2 years
Electrical components: 1 year
Other components: 1 year, except for tyres, inner tubes and accessories that are subject to wear.

The company assumes no liability for indirect or special damages. This warranty applies only to the original purchaser, in the possession of a
fiscal document proving the exact purchase date.
This warranty is applicable only in the case of defective components and does not cover the effects of normal use or damage caused by
accidents, abuse, excessive loading, negligence, improper assembly, improper maintenance or adding objects that are inconsistent with the
normal use of the bicycle.

No bicycle is indestructible and no claims are accepted for damage caused by improper use, by use in competitions, acrobatics, jumps, leaps or
similar activities. Claims must be made at the retailer, where the bicycle was purchased.
This warranty has no effect on your rights by law.

The company reserves the right to change or correct any specification without notice. All information and specifications in this manual are
correct at the time of printing.

I. Terms and conditions for using this pedal assisted electric bicycle

This pedal assisted electric bicycle is designed to be used on the road or on paved surfaces where the tyres do not lose contact with the ground. It
must be maintained according to the instructions in this booklet
The maximum weight of the cyclist including the load must be less than 100 kg.

Safety:

Before starting to use the pedal assisted electric bicycle, make sure it is completely safe.
Specifically check:

- nuts, bolts, fasteners, and that all components to be fixed on are tightened and are not worn or damaged

- the steering position is comfortable

- the brakes work effectively

- the steering is free without too much play

- the tyres are not damaged and are inflated to the correct pressure

- the pedals are screwed correctly onto the crankarms

PLEASE NOTE: Your pedal assisted electric bicycle should be professionally checked every six months to ensure correct and safe

functioning. It is the user’s responsibility to ensure all components are able to guarantee correct functioning. It is very important to check the
tyres monthly and control the wear line and, if the groove becomes invisible, the tyre is no longer working safely. A particularly worn tyre is very
dangerous and must be replaced. Adjust the brake pads at a 1-1.5mm distance from the rim.

FREQUENTLY CHECK THE TENSION OF THE SPOKES OF THE WHEEL DRIVE.

2

PLEASE NOTE: We inform you that the user assumes personal risk for injuries, damage or losses if the above conditions are violated, and the
warranty will be automatically annulled.

List of components for the pedal assisted electric bicycle

1

Tyres & tube

15

Controller box

2

rims16Battery

3

spokes

17

Rear carrier

4

Front fork

18

Speed sensor

5

Front brake

19

Rear mudguard

6

Front mudguard

20

Kick stand

7

Handlebar stem

21

Cranks & chain wheel

8

frame

22

Pedals

9

Display unit

23

Chain cover

10

Brake levers

24

Motor cable joint where fitted

12

Rear brake

25

Front hub

13

Seat clamp

26

Rear hub motor

14

Saddle & seat post

The cyclist must pedal forward to obtain assistance from the electrical motor. This is an important feature in terms of safety. This pedal assisted
bicycle provides assistance up to 25 km/h, after which, the electrical motor no longer works. It is possible to go faster, but only by personal effort
and no electrical assistance.

To use the bike in the electric mode, turn on the power switch on the battery side, under the handle and the on/off button on the display. The
motor will start after one complete revolution of pedalling. This feature protects the motor and the control unit from possible damage and
preserves the life of the various electrical components.

Contents

1-Structure pedal assisted electric bicycle
2-Safety notes
3-Operations prior to use
4-Battery installation and function
5-Display functions
6-Battery use and maintenance
7-Battery charger use and maintenance
8-Hub motor use and maintenance
9-Electric control unit maintenance
10-“Power-off control” maintenance of the brake levers
11-Troubleshooting
12-General technical specifications

1 – Structure of the pedal assisted electric bicycle (see parts I/II)
2 – Safety notes