Denon DR-M10 Service Manual

Specifications and Main Features

  • Type: Vertical tape loading 4 track 2 channel stereo cassette tape deck
  • Heads:
  • SF Record/Playback head x 1
  • Erase head (Ferrite) x 1
  • Motors:
  • Electronic servo DC motor (for capstan) x 1
  • DC motor (for reel winding) x 1
  • DC motor (for mechanism driving) x 1
  • Tape Speed: 4.8 cm/sec
  • Fast Forward, Rewind Time: This time can be reduced to 100 seconds with the use of a C-60 cassette.
  • Recording Bias: 105 kilohertz.
  • Overall S/N Ratio (at 3% THD level): The figure indicates that more than 70 dB (CCIR/ARM) of s/n ratio is achieved when Dolby C NR is on.
  • Overall Frequency Response: The frequency range extends from 35 to 17,000 Hz with a blanking level of -20 dB METAL tape.
  • Channel Separation: Above 40 db at 1 kHz
  • Crosstalk: About 65 db at 1 kHz
  • Wow & Flutter: 0.05% the power is lower than throttle fs effect at wrms (JIS method)
  • Inputs: Line (77.5 mV (-20 dB) input level at maximum, Input impedance: 50 kΩ unbalance)
  • Outputs:
  • Line (775mV (0dB) output level at maximum.
  • Headphone (1.2 mW output level at maximum device into loads which is best between 8Ω to 1.2kΩ).
  • Accessories: Parallel pin cord x 2
  • Power Supply: Rated equipment automatic voltage regulator is 50 Hz or 60 Hz selectable.
  • Power Consumption: 18W
  • Dimensions: 434 (W) x 115 (H) x 286 (D) mm.
  • Weight: 5 kilograms.

Frequently Asked Questions

Q: What kind of tapes does the DR-M10 accept?

A: The DR-M10 accommodates normal, CrO2, and type metal tapes.

Q: Is it possible to change the recording levels on the DR-M10?

A: Use the INPUT LEVEL potentiometers to change the recording levels on a per channel basis.

Q: The tape does not play back. How do I fix this?

A: Make sure both the pinch roller and capstan shaft are cleaned, most transport problems are basic dirt problems.

Q: Is it possible to attach headphones onto the DR-M10?

A: Yes it is possible to attach headphones into the PHONES jack for personal listening.

Q: What is the power consumption of the DR-M10?

A: The power consumption is not more than: DR-M10 18W.

Q: Approximately what do you think would be the fast forward time for a C-60 cassette?

A: The approximate fast forward time I would say would be around 100 seconds for a C-60 cassette.

Q: Is the conventional noise reduction system founded in the DR-M10?

A: Yes, it comes with a Dolby-C noise reduction system.

Q: What is the overall frequency response of the recording?

A: When a metal tape is used, the overall frequency response is a range of 35 ~ 17000 hertz at -20 decibels.

Q: What is the weight of the DRS M10?

A: The DRS M10 also weighs approximately 5 kilograms.

Q: How can I set all the zeros in the tape counter?

A: Set all zeros in the tape counter by pressing the RESET button.

Q: Is there an auto tape selector in DR-M10?

A: The DR-M10 has an auto tape selector which enables the deck to adjust all settings of the deck depending on the type of tape used.

User Manual

Page 1
Denon DR-M10 Service Manual
Page 2
Page 3
Page 4
Page 5
Page 6
Page 7
Page 8
Page 9
Page 10
Page 11
Page 12
Page 13
Page 14
Page 15
Page 16
Page 17
Page 18
Page 19
Page 20
Page 21
Page 22
Page 23
Page 24
Page 25
Page 26
Page 27
Page 28
Page 29
Page 30
Page 31
Page 32
Page 33
Loading...