Denon DRA-697CIHD - Premier AM/FM Stereo User Manual

DENON AVR/AVC/DRA control protocol

Application model : DRA-697CiHD (HD Radio upgraded DRA-697ci)

Application terminal : RS-232C

Connector specification

Connector type : DB-9pin female type, slave straight connection (DCE type)

( 1pin : GND , 2pin : TxD , 3pin : RxD , 5pin : Common(GND) , 4,6,7,8,9pin : NC )

Communication format :

Synchronous system : Tone step synchronization

Communication system : A half duplex
Communication speed : 9600bps

Character length : 8 bits
Parity control : None

Start bit : 1 bit
Stop bit : 1 bit

Communication procedure : Non procedural
Communication data length : 135 bytes (maximum)

15 January 2007

Ver. 5.0.0

- 1 -

15 January 2007

Protocol specification

The following three data forms is defined.
COMMAND : The message sent to a system(AVR/AVC/DRA) from a controller(Touch Panel etc.)
A command to a system is given from a controller.

EVENT : The message sent to a controller(Touch Panel etc.) from a system(AVR/AVC/DRA)
The result is sent, when a system is operated directly and a state changes.

*The form of EVENT presupposes that it is the same as that of COMMAND.

**Refer to the following table for the contents of COMMAND and EVENT.
RESPONSE : The message sent to a controller(Touch Panel etc.) from a system(AVR/AVC/DRA)

if the ‘request command’ (COMMAND+?+CR(0x0D)) has came from a controller.
The RESPONSE should be sent within 200ms

*The form of RESPONSE presupposes that it is the same as that of EVENT.

of receiving the COMMAND.

Basic specification : The command by ASCII CODE, parameter expression

*ASCII CODE which can be used is from 0x20 to 0x7F : the alphabet and the number of 0-9 , and space (0x20) , Some signs ,

AND carriage return(0x0D)--- It is used only as a pause sign.

Command structure : COMMAND + PARAMETER + CR(0x0D)

COMMAND : ASCII CODE of 2 characters

ex. SI : Select Input source
MS : surround Mode Setting

MV : Master Volume setting
PW : system PoWer setting

PARAMETER : ASCII CODE ( up to 25 characters)
ex. DVD : function name

CDR/TAPE : function name

*Special Parameter--- ? : for request command

- 2 -

The example of a command * <CR> is the meaning of 0x0D.

SIDVD<CR> : Select Input source DVD
MVUP<CR> : Master Volume UP

PWON<CR> : system PoWer ON
PWSTANDBY<CR> : system PoWer STANDBY

SI?<CR> : Request command for now playing input source >> Return RESPONSE ‘SI***<CR>’

15 January 2007

- 3 -

15 January 2007

Others

A) COMMAND is receivable also during transmission of EVENT.
B) Since CHANNEL VOLUME changes simultaneously when the SURROUND MODE changes, the value of the channel volume of all channels

returns as EVENT.

C) CHANNEL VOLUME returns the data of ALL channels by the present SURROUND MODE also including an intact channel. In this case,

the data of an intact channel is set to "50".

D) Since SURROUND MODE changes simultaneously when the INPUT source changes, the SURROUND MODE (and also the value of the channel

volume of all channels , It described in B) ) returns as EVENT.

E) When SURROUND MODE is the same in between INPUT source change before and after, EVENT of SURROUND MODE and CHANNEL VOLUME

does NOT return.

F) Although EVENT of SURROUND MODE returns when the present SURROUND MODE is set up again, CHANNEL VOLUME does NOT return.

G) When SURROUND MODE is changed, before returning SURROUND MODE after change as EVENT, the present SURROUND MODE is returned.
H) The RESPONSE should be sent as opposed to the request command by all the commands with which an EVENT exists , not need to

the another request commands(ex. SV command).

I) The PARAMETER (with COMMAND and RESPONSE, EVENT) of minimum level of MASTER VOLUME defines “99”.
J) Four seconds later, please transmit the next COMMAND after transmitting a power on COMMAND（PWON).

- 4 -

COMMAND and PARAMETER list

15 January 2007

PW ON POWER ON/STANDBY change PWON<CR>
STANDBY PWSTANDBY<CR>
? Request PW Status PW?<CR>
MV UP MASTER VOLUME UP/DOWN , direct change to **dB MVUP<CR>
DOWN MVDOWN<CR>
** **:00 to 99 by ASCII , 80=0dB, 99=---(MIN) MV80<CR>
? Request MV Status MV?<CR>
CV FL UP CHANNEL VOLUME UP/DOWN , direct change to **dB CVFL UP<CR>
FL DOWN **:38 to 62 by ASCII , 50=0dB CVFL DOWN<CR>
FL ** CVFL 50<CR>
FR UP CVFR UP<CR>
FR DOWN CVFR DOWN<CR>
FR ** CVFR 50<CR>
SW UP CVSW UP<CR>
SW DOWN CVSW DOWN<CR>
SW ** CVSW 50<CR>
? Request CV Status CV?<CR>
MU ON OUTPUT MUTE ON/OFF change MUON<CR>
OFF MUOFF<CR>
? Request MU Status MU?<CR>
SI ATUNER Select INPUT source SIATUNER<CR>
PHONO SIPHONO<CR>
CD SICD<CR>
CDR/TAPE SICDR/TAPE<CR>
DVD SIDVD<CR>
VCR SIVCR<CR>
IPOD SIIPOD<CR>
V.AUX SIV.AUX<CR>
XM RADIO (North America model only) SIXM RADIO<CR>
HD RADIO (North America model only) SIHD RADIO<CR>

COMMAND PARAMETER

MV , CV COMMAND : "*" parameter uses two ASCII characters. (see page4 J) section)

function example

- 5 -

15 January 2007

ZM ON MAIN-ZONE ON/OFF change ZMON<CR>
OFF ZMOFF<CR>
? Request ZM Status ZM?<CR>
BAND TUNER BAND SELECT ZMBAND<CR>
SEARCH TUNER SEARCH SELECT ZMSEARCH<CR>
Z2 ON MUTI ZONE-2 ON/OFF change Z2ON<CR>
OFF Z2OFF<CR>
? Request Z2 Status Z2?<CR>
UP MULTI ZONE-2 VOLUME UP/DOWN , direct change to **dB Z2UP<CR>
DOWN Z2DOWN<CR>
** **:00 to 99 by ASCII , 80=0dB, 99=---(MIN) Z280<CR>
PHONO MULTI ZONE-2 mode set , and select source Z2PHONO<CR>
ATUNER ---The name of PARAMETER is Z2ATUNER<CR>
CD the same as that of the time of SI COMMAND. Z2CD<CR>
DVD Z2DVD<CR>
V.AUX Z2V.AUX<CR>
CDR/TAPE Z2CDR/TAPE<CR>
IPOD Z2IPOD<CR>
VCR Z2VCR<CR>
XM RADIO (North America model only) Z2XM RADIO<CR>
HD RADIO (North America model only) Z2HD RADIO<CR>
SOURCE Z2SOURCE<CR>
MUON ZONE2 OUTPUT MUTE ON/OFF change Z2MUON<CR>
MUOFF Z2MUOFF<CR>
MU? Request Z2MU Status Z2MU?<CR>
BAND ZONE2 TUNER BAND Select Z2BAND<CR>
TPUP ZONE2 TUNER PRESET UP/DOWN Change Z2TPUP<CR>
TPDOWN Z2TPDOWN<CR>
TP** ** PRESET Number Direct Set Z2TP**<CR>
TFXM*** --- *** : XM CH No.(ZONE2) (North America model only) Z2TFXM001<CR>

COMMAND PARAMETER

Z2 COMMAND : "*" parameter uses two or three ASCII characters. (see page4 J) section)

function example

(XM001 CH at XM)

- 6 -