Denon DHT-589BA, AVR589 Owner’s Manual

DENON

AV SURROUND RECEIVER

AV ,-5

Owner's Manual Manuel de I'Utilisateur

[_ SAFETY PRECAUTIONS

CAUTION:

TO REDUCE THE RiSK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER-SERVICEABLE PARTS iNSiDE. REFER SERViCiNG TO QUALiFiED SERVICE PERSONNEL.

The lightning flash with arrowhead symbol, within an equilateral

_h triangle, is intended to alert the user to the presence of

_j_ The exclamation point within an equilateral triangle }s intended

uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons,

to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance.

WARNING:

TO REDUCE THE RiSK OF FIRE OR ELECTRIC SHOCK, DO NOT

EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE,

SAFETY INSTRUCTIONS

Read Instructions -All the safety and operating instructions should be read before the product is operated.

Retain Instructions - The safety and operating instructions should be retained for future reference.

Heed Warnings - All warnings on the product and in the operating instructions should be adhered to.

Follow Instructions -All operating and use instructions should be followed.

Cleaning - Unplug this product from the wall outlet before cleaning. Do not use liquid cleaners or aerosol cleaners.

Attachments - Do not use attachments not recommended by the product manufacturer as they may cause hazards.

Water and Moisture ----Do not use this product near water - for example,

near a bath tub, wash bowl, kitchen sink, or laundry tub; in a wet basement; or near a swimming pool; and the like. Accessories ----Do not place this product on an unstable cart, stand, tripod, bracket, or table. The product may fall, causing serious injury to a child

or adult, and serious damage to the product. Use only with a cart, stand, tripod, bracket, or table recommended by the manufacturer, or sold with the product. Any mounting of the product should follow the manufacturer's instructions, and should

use a mounting accessory recommended by the

manufacturer.

A product and cart combination should be moved

with care. Quick stops, excessive force, and

uneven surfaces may cause the product and cart

combination to overturn.

10.

Ventilation ----Slots and openings in the cabinet are provided for ventilation

and to ensure reliable operation of the product and to protect it from

overheating, and these openings must not be blocked or covered. The

openings should never be blocked by placing the product on a bed, sofa,

rug, or other similar surface. This product should not be placed }n a built-in

installation such as a bookcase or rack unless proper ventilation }s provided

or the manufacturer's instructions have been adhered to.

11.

Power Sources ----This product should be operated only from the type of

power source indicated on the marking label. If you are not sure of the type

of power supply to your home, consult your product dealer or local power

company. For products intended to operate from battery power, or other

sources, refer to the operating instructions.

12.

Grounding or Polarization -This product may be equipped with a polarized

alternating--current line plug (a plug having one blade wider than the other). This plug will fit into the power outlet only one way. This is asafety feature.

If you are unable to insert the plug fully into the outlet, try reversing the

plug. If the plug should still fail to fit, contact your electrician to replace your

obsolete outlet. Do not defeat the safety purpose of the polarized plug.

NEC-NATIONAL ELECTRICAL CODE (NEC ART 250, PART H)

ELECTRODE SYSTEM

13. Power--Cord Protection - Power-supply cords should be routed so that they are not likely to be walked on or pinched by items placed upon or against

them, paying particular attention to cords at plugs, convenience receptacles,

and the point where they exit from the product.

15. Outdoor Antenna Grounding ----If an outside antenna or cable system is connected to the product, be sure the antenna or cable system is grounded so as to provide some protection against voltage surges and built-up static charges. Article 810 of the National Electrical Code, ANSI/NFPA 70, provides information with regard to proper grounding of the mast and supporting structure, grounding of the lead--in wire to an antenna discharge unit, size of grounding conductors, location of antenna--discharge unit, connection to grounding electrodes, and requirements for the grounding electrode. See Figure A.

16. Lightning - For added protection for this product during a lightning storm, or when it is left unattended and unused for long periods of time, unplug it

from the wall outlet and disconnect the antenna or cable system. This will

prevent damage to the product due to lightning and power-line surges.

17. Power Lines - An outside antenna system should not be located in the

vicinity of overhead power lines or other electric light or power circuits, or

where it can fall into such power lines or circuits. When installing an outside antenna system, extreme care should be taken to keep from touching such power lines or circuits as contact with them might be fatal.

18. Overloading - Do not overload wall outlets, extension cords, or integral convenience receptacles as this can result in a risk of fire or electric shock.

19. Object and Liquid Entry ----Never push objects of any kind into this product

through openings as they may touch dangerous voltage points or short-out

parts that could result in a fire or electric shock. Never spill liquid of any kind on the product.

20. Servicing - Do not attempt to service this product yourself as opening or removing covers may expose you to dangerous voltage or other hazards. Refer all servicing to qualified service personnel.

21. Damage Requiring Service - Unplug this product from the wall outlet and refer servicing to qualified service personnel under the following

conditions: a) When the power--supply cord or plug is damaged,

b) If liquid has been spilled, or objects have fallen into the product, c) If the product has been exposed to rain or water, d) If the product does not operate normally by following the operating

instructions. Adjust only those controls that are covered by the operating instructions as an improper adjustment of other controls may result in damage and will often require extensive work by a qualified technician to restore the product to its normal operation,

e) If the product has been dropped or damaged in any way, and

f) When the product exhibits a distinct change in performance - this

indicates a need for service.

22. Replacement Parts ----When replacement parts are required, be sure the service technician has used replacement parts specified bythe manufacturer or have the same characteristics as the original part. Unauthorized substitutions may result in fire, electric shock, or other hazards.

23. Safety Check ----Upon completion of any service or repairs to this product, ask the service technician to perform safety checks to determine that the product is in proper operating condition.

24. Wall or Ceiling Mounting - The product should be mounted to a wall or ceiling only as recommended by the manufacturer.

25. Heat ----The product should be situated away from heat sources such as radiators, heat registers, stoves, or other products (including amplifiers) that produce heat.

FCC iNFORMATiON (For US customers}

1. PRODUCT This product complies with Part 15 of the F:CCRules. Operation is subject to the following two conditions: (1) this

product may not cause harmful interference, and (2) this product must accept any interference received, including interference that may cause undesired operation.

2. IMPORTANT NOTICE: DO NOT MODIFY THIS PRODUCT This product, when installed as indicated in the instructions contained in this manual, meets F:CC requirements.

Modification not expressly approved by DENON may void your authority, granted by the FCC, to use the product.

3. NOTE This product has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15

of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.

This product generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur ina particular installation. If this product does cause harmful interference to radio or television reception, which can be determined by turning the product OFF and ON, the user is encouraged to try to correct the interference by one or more of the following measures: o Reorient or relocate the receiving antenna. o Increase the separation between the equipment and receiver. o Connect the product into an outlet on a circuit different from that to which the receiver is connected. o Consult the local retailer authorized to distribute this type of product or an experienced radiof[V technician for

help.

This CJass B digital apparatus complies with Canadian ICES--O03.

Cet appare}l numerique de la classe B est conforme _ la norme NMB--OO3 du Canada.

[_ NOTE ON USE / OBSERVATIONS RELATIVES A L'UTILISATION

• Do not let foreign objects into the unit.

• Ne pas laisser des objets 6trangers dans I'appareil.

• Avoid high temperatures. Allow for sufficient heat dispersion when

installed in a rack.

• Eviter des temp6ratures 6levees. Tenir compte d'une dispersion de chaleur

suffisante Iors de I'instalIation sur une 6tag6re.

Keep the unit free from moisture, water, and dust.

Prot6ger I'appareil contre I'humidite, I'eau et la poussiere.

Unplug the power cord when not using the unit for long periods of time.

D6brancher le cordon d'alimentation Iorsque I'appareil n'est pas utiIis6 pendant

de Ionguesp6riodes.

Handle the power cord carefully. Hold the plug when unplugging the cord.

• Manipuler le cordon d'aIimentation avec precaution. Tenir la prise Iors du dBbranchement du cordon.

_! ///

(Forapparatuseswith ventilation holes)

Do not obstruct the ventilation holes. Ne pas obstruer les trous d'a6ration.

Never disassemble or modify the unit in any way.

Ne jamais demonter ou modifier I'appareil d'une maniere ou d'une autre.

Contents

Accessories ............................................... 2

Cautions on Handling ..................................................................... 3

Cautions on Installation ................................................................. 3

About the Remote Control Unit .................................................... 3

Insemng the Batteries ................................................................... 3

Operating Raqge of the Remote Contro Unit ................................ 3

Part Names and Functions ............................................................ 4

Front Pane ................................................................................. 4

DisDlav .......................................................................................... 4

Rear Pane ...................................................................................... 5

Remote Control Unit ...................................................................... 6

Preparations .................................................................................... 7

Cables Used for Conr ectlons ...................................................... 7

Speaker Connections ..................................................................... 8

Speaker Installatior ....................................................................... 8

SpeaKer Connect ons .............................................................. 9

Connecting Equipment with HDMI connectors ........................ I0

Connecting the Monitor .............................................................. ' "

Connecting the Playback Components ..................................... " "

DVD Raver .......................................................................... 11

CD Plaver .................................................................................. 12

Pod@.......................................................................................... 12

TV rCABLE Tuner .......................................................................... 12

Connecting the Recording Components ................................... 1

Video Cassette Recorder ......................................................... 13

CD Rec_raer/MD Recorder !Tape Deck .................................... 13

Connections to Other Devices ..................................... 13

Video Camera /Game Console .................................................... 13

Coroonem wttn Multi-channel Output connecTors .................... 14

SIRIUS connector ............................................................. 14

Antenn_ terminals ..................................................................... 15

Connecting the Power Cord ....................................................... I5

Once Connections are Completed ............................................. 15

Menu Map ................................................................................... 16 1_ Standard Playback ................................................ 27

Exam pies of Front Display ........................................................... 16 Surround Plavback of 2-channel Sources .................................... 27

Playing Multi-channe Sources Do by Digital, DTS, etc.) ............. 27

DSP Simulation Playback ....................................................... 28

Direct Playback ....................................................................... 28

_ Stereo Playback ....................................................................... 28

Preparations .................................................................................. 17

Auto Setup .................................................................................. 18

[] Auto Setup .............................................................................. 18

[] -rror Messages ...................................................................... 19 -

Adjusting the parameters ............................................................ 29

Surround Parameter ................................................................. 29

[] Moae ................................................................................... 30

[] Cinema EQ ............................................................................ 30

System Setup Operation ........................................................... 20

Exam pie of Display of Default Vagues ........................................ 20

1. Speaker Setup .......................................................................... 21

[]_ [] Speaker Configuration ..................................................... 21

[] Subwoofer Mode Setu_ ........................................................ 21

Jr_ m Dstance ..................................................................... 22

m _-[] Crossover Frequency ...................................................... 22

[] Test Tone ................................................................................ 22

[] Restore .................................................................................. 23

2. input Setup ............................................................................... 23

[],[] HDMI nAssig .............................................................. 23

lq-. [] Digital In Assign ........................................................ 24

[] iPod Asslg- -............................................................................ 24

[] Audio Delay. ............................................................................ 24

[] EXT. IN Subwoofer Leve ........................................................ 24

[] Auto Preset Memorv .............................................................. 24

m Parema LOCK........................................................................... 25

m Edit _OCKCode ........................................................................ 25

3. Option Setup ............................................................................. 26

[]-- [] Volume Comro ............................................................... 26

[] Auto SurreJnd Mode ............................................................. 26

[] D.ComD (Dynamic Range Compression) ................................ 30

[] LFE........................................................................................ 30

[] Center image ......................................................................... 30

I_ Panorama .......................................................................... 30

[] Dirr_nsion ............................................................................. 30

D Center Width ........................................................................ 30

[] Delav Time ..................................................................... 30

[] Effect Level ........................................................................... 30

m Room Size............................................................................... 30

[] SA/ATT (3ubwoofer Attenuation ........................................... 3"

[] Subwoofe ............................................................................. 31

[] Tone Contro .......................................................................... 31

[] Bass ........................................................................................ 31

[] Treble ........................................................................ 31

[] MultEQ .................................................................................... 31

[] Dvnamic EQ ........................................................................... 31

[] Dynamic Volume ................................................................... 32

[] DV Setting (Dynamic Volume Setting) .................................... 32

[] RESTORER ............................................................................. 32

[] Night Mode ............................................................................. 33

[] Default .................................................................................... 33

I!_ Direct Mode SetuE................................................................... 26

[] Remote D Setup .................................................................... 26

Preparations ............................................................................... 3=

-JrHng the Power On ................................................................ 33

Selecting the InDut Source ............................ 34

Setting tne InDuI Mode ............................................................... 34

Operations Durirg Playback ......................................................... 35

Playing Video and Audio Equipment ......................................... 35

Basic Operation ......................................................................... 35

Listening to FM/AIVI Broadcasts ................................................ 36

Basic Operation ............................................................................ 36

Presetting Radio Staticns (Preset Memorvl ................................ 36

Li_tenlrg to Preset Stations ........................................................ 36

Listening to SiRiUS Satellite Radio Programs .......................... 37

Basic Oaeradon .......................................................................... 37

Checking me SiRiUS Signal Strength and Radio ID.................... 37

Searching Categories .................................................................. 38

Parental Lock ................................................................................ 38

iPod ® Playback ............................................................................. 38

Preparations ........................................................ 3_

Li_te-- g to Audio ..................................................................... 33

/iewing Still Pictures or Videos on the iPod .............................. 39

Other Operations....;i:, v..... :::.,:.:..;i....;. ,::..... ::,.:.:;::.,.-i::_::;.:.:.::.=O

Reqording On an External Device (REC OUT mode)!i-:: :;.:::-:i. i=0

Convenient Functions ::::::::::::::::::::::::: ========================================

Channel Level .:.:...:..::.:::.;...Lib::::. :.:,L:,:,IS::,L::I.:,::-::;:.:.:.:;_I..I_:40

Quick Select Function ..:;..:.;..ii:.:;;.i;;-:. :.:.i;,::::: :::::, .:..:-i:i.,:;.,41 Personal Memory Plus Function .I::.I::.:L:..-:;.L;?.:::.- .:::.i.;.:.::.:::41

East Function Memory .:L:,:L::.L: i.:.:: i:.££!. :k::.;i:.;,k:i.;,.:.::..::.;:41 Backup Memory.:.::.:::.::::.:..;:,:..:::.::..:: .;.:.;,:i : .:. ::: ;.: :.:.::..; 41

Resetting the Microprocessor ..................................................... 41

Thank you for purchasing this DENON product. To ensure proper

operation, please read this owner's manual carefully before using the product.

After reading them, be sure to keep them for future reference.

Check that the following parts are supplied with the product.

_ Owner's manual ...................................................................... 1

_ Getting Started ........................................................................ 1

Warranty (for North America model only) ................................ 1

Service station list ................................................................... 1

(5_ Remote control (RC-1104) ........................................................ 1

6_ R6/AA batteries ....................................................................... 2

(7-}FM indoor antenna .................................................................. 1

AM loop antenna ..................................................................... 1

(9_ Setup microphone

(DM-A409, Cord length: Approx. 25 ft / 7.6 m) ....................... 1

® ®

_:_

Operating DENON Audio Presetting:::: :,:i: :::.:i:i ..:::,:i,il.i.;:.;i :i;:i;::,.i;:i-:i:.:ii:i;:i-:i:.::ik;42

Operating Preset Components:,L,£:,:-;:.,£:,:-4:;:.,£:,:-4:;:.,£:,:,42 Punch Through Function ===============================================================

* Before turning the power switch on

* Power is supplied to some of the circuitry even when the unit is

* About condensation

* Cautions on using mobile phones

* Moving the unit

F' i

* Note that the illustrations in these instructions may differ from the

..................................Note:

Uz:_

11;

For proper heat dispersal, do not install this unit in a confined

space, such as a bookcase or similar enclosure.

Check once again that all connections are correct and that there are

no problems with the connection cables.

set to the standby mode. When traveling or leaving home for long periods of time, be sure to unplug the power cord from the power

outlet.

If there is a major difference in temperature between the inside of the unit and the surroundings, condensation (dew) may form on the operating parts inside the unit, causing the unit net to operate properly.

If this happens, let the unit sit for an hour or two with the power turned off and wait until there is little difference in temperature before using the unit.

Using a mobile phone near this unit may result in noise. If so, move the mobile phone away from this unit when it is in use.

Turn off the power and unplug the power cord from the power outlet.

Next, disconnect the connection cables to other system units before

moving the unit.

actual unit for explanation purposes.

"//////////////////////////////////////////////////

•_ Note

X////////////////////////////////////////////////×

In addition to the AVR-589, the included remote control unit (RC-1104) can also be used to operate the equipment listed below.

@} DENON system components

Non-DENON system components

o By setting the preset memory (L_page 42 ~ 44)

@_Lift the clasp and remove the rear lid. _,_

Load the two batteries properly as indicated f_,.._¢_.'---.._ by the marks in the battery compartment, f_o'o_ _"'_

m6/AA '__'_

@ Put the rear cover back on.

* Replace the batteries with new ones if the set does not operate

even when the remote control unit is operated close to the unit. * The supplied batteries are only for verifying operation. * When inserting the batteries, be sure to do so in the proper direction,

following the "0" and "@" marks in the battery compartment. oTo prevent damage or leakage of battery fluid:

o Do not use a new battery together with an old one.

o Do not use two different types of batteries.

o Do net attempt to charge dry batteries.

o Do not short-circuit, disassemble, heat or dispose of batteries in

flames.

o If the battery fluid should leak, carefully wipe the fluid off the inside

of the battery compartment and insert new batteries. o Remove the batteries from the remote control unit if it will not be in

use for long periods.

oWhen replacing the batteries, have the new batteries ready and

insert them as quickly as possible.

Point the remote control unit at the remote sensor when operating it.

30°

-..

Approx. 23 feet / 7 m

The set may function _mproperly or the remote control unit may net

operate if the remote control sensor is exposed to direct sunlight, strong artificial light from an inverter type fluorescent lamp or infrared light.

'-....

Wall

For buttons not explained here, see the page indicated in parentheses ().

...............1 I-H T,,,'<I

kk -

.................:

_}) INPUT mode indicators .............................. (34)

_) SIGNAL indicators _) Display

SPEAKERS indicators ................................. (35)

Remote control sensor ................................ (3)

_) REC SELECT button ................................... (40)

_) SOURCE SELECT knob .............................. (34)

_) SOURCE button .......................................... (34)

_!) STATUS button .......................................... (33)

DIMMER button .......................................... (35)

_) RESTORER button ...................................... (32)

_) BAND button .............................................. (36)

SHIFT button ............................................... (36)

PRESET CHANNEL buttons (AT) .............. (36)

_) TUNING buttons (AT) ................................ (36)

_) MULTEQ button ......................................... (31)

_D DYNAMIC VOLUME button ....................... (32)

•_ About Dynamic Volume Audyssey Dynamic Volume TM solves the problem of large variations in volume level between television programs, commercials, and between the soft and loud passages of movies. Audyssey Dynamic EQTM is integrated into

Dynamic Volume so that as the playback volume is adjusted automatically, the perceived bass response, tonal balance, surround impression,

and dialog clarity remain the same.

•_ About Dynamic EQ Audyssey Dynamic EQ solves the problem of

deteriorating sound qualityas volume isdecreased .................................

by taking into account human perception and i

room acoustics. Audyssey Dynamic EQ works in _i

tandem with Audyssey MultEQ @to provide well- _6

balanced sound for every listener at any volume ...................................

level, ii_

@VIDEO SELECT button ............................... (35)

_:_

O Power operation button

(ON/STANDBY) .......................................... (34)

Power indicator .......................................... (34)

O Power switch (_ON mOFF} ............... (34, 41)

O Headphone jack (PHONES) ........................ (35)

O INPUT MODE button .................................. (34)

OSPEAKERS buttons .............................. (35, 41)

QUICK SELECT buttons ............................. (41)

V. AUX INPUT connectors

Remove the cap covering the connectors when

you want to use them.

lL II

o o o 0 0 ......... j_., ,,_#, +

SETUP MIC jack .......................................... (17)

_) SYSTEM SETUP button ............................. (20)

SURF{. MODE / SURF{. PARA button ..... (27, 29)

_SELECT/ENTER knob

*The SELECT/ENTER knob on the main unit

operates in the same way as the cursor <] and D buttons on the remote control unit.

SELECT / ENTER

*The control functions in the same way as the

cursor <] button when turned counterclockwise, as the cursor D button when turned clockwise.

©The control functions in the same way as the

ENTER button when pressed the knob.

_)Cursor buttons (AV) ................................. (20)

_) MASTER VOLUME control knob ............... (35)

_) Dynamic Volume indicator ........................ (32)

MultEQ indicator ........................................ (31)

Master volume indicator

_]_Signal channel indicator

Lights when the preset channel is displayed at

Information display Input signal indicators

Master volume indicator This displays the volume level.

The Setup item number is displayed in System Setup.

Recording output source indicator This lights when the REC OUT mode is

selected. (This indicator is off when "SOURCE"

is selected.)

_Tuner reception mode indicators

These light according to the reception conditions when the input source is set to "TUNER".

* AUTO

This lights when in the auto tuning mode.

* STEREO

In the FM mode, this lights when receiving

analog stereo broadcasts.

* TUNED

This lights when the broadcast is properly tuned in.

)CK CONTROL _,_ SIRIUS l

_]_ Digital audio connectors

(OPTICAL / COAXIAL) .................. (10 ~ 12, 14)

_VIDEO / S-VIDEO connectors ............ (11 ~ 13)

_Analog audio connectors

(AUDIO) ............................................... (10 ~ 13)

EXT, iN connectors ..................................... (14)

PRE OUT connector ...................................... (g)

_AC OUTLETS ............................................... (15)

CD-R/ VCR DVD/ TV/ VCR CD-R/

TAPE HOP CBL flPod) TAPE

_ Power cord .................................................. (15)

_Speaker terminals (SPEAKERS) .................. (g)

FM/AM antenna terminals

(TUNER ANTENNA) .................................... (15)

_COMPONENT WDEO connectors ......... (11, 12)

_HDMI connectors ................................ (10 ~ 12)

_SIRIUS connector (SATTU) ........................ (14)

_) DOCK CONTROL jack ................................. (12)

CO SW SR

SPEAKER IMPEDANCE

FRONTAORS: _1_£_ RENTER :6_16£z

A + £ :12_16£_ SURROUND : 6_16_

AC OUTLETS

AC120V

60Hz

SWITCHEDTOTAL120W(1_) MAX.

[ Front ]

-.@

--@

[ Rear ]

Indicator ...................................................... (42)

Power buttons ............................................ (34)

_QUICK SELECT buttons ............................. (41)

_]_Source select buttons ................................ (34)

•_ :To select "SIRIUS" as the input source, use the SAT TU button.

_System buttons .................................... (39, 43)

_AUDIO DELAY button ................................ (24)

_Cursor buttons (AV< D) ......................... (20)

DYNAMIC VOLUME button ....................... (32)

RESTORER button ...................................... (32)

_}SOURCE CONTROL switches .................... (36)

Remote control signal transmitter

Master volume control buttons ................ (35)

_) MUTING button .......................................... (35)

_) NIGHT button ............................................. (33)

_) MULTEQ button .......................................... (31)

@Channel select (CH SEL) /

ENTER button ....................................... (20, 40)

,., _ DVB/4DP YC£ SA{ ZJBL IV

/ io coGE

_DVD/HDP TV/CB VCR

AUX VAUX C04_/TAPE_

i _ I lI_1_llm) iPod SATTU I

II1 ]o o oil _

VVOL _ D/ST 5CH SIMU=

111

#0DE "YST_ _ PARA

_l_ ....................

',%1

_t Power buttons ............................................ (44)

_Source select buttons ................................ (34)

•_ :To select "SIRIUS" as the input source, use the SAT TU button.

_Video select button (V.SEL) ....................... (35)

_Tuner system buttons ................................ (36)

_Test tone button (TEST) ............................ (23)

_Surround mode buttons ................ (27, 28, 30)

_System setup button (SYSTEM} ............... (20)

_Surround parameter button (PARA)... (27, 29)

Enter button (ENT) ..................................... (20)

_} Input mode button (INPUT) ....................... (34)

_Cursor buttons (AV<] D) ......................... (20)

_Po_/NEn_0RK1 rXUN_

AUDIO --CD--

.................................?

DENON

If buttons on the front or rear are pressed strongly, the button on the opposite side will be activated too.

Connections for all compatible audio and video signal formats

are described in this owner's manual. Please select the types of

connections suited for the equipment you are connecting. With some types of connections, certain settings must be made

on the AVRi589. For details, refer to the instructions for the

respective connection items below.

Select the cables according to the equipment being connected.

* Do not plug in the power cord until all connections have been

completed.

oWhen making connections, also refer to the operating instructions of

s i

.............. i

the other components.

o Be sure to connect the left and right channels properly (left with left,

right with right).

o Do not bundle power cords together with connection cables. Doing

so can result in humming or noise.

Coaxial digital connections

Optical digital connections

Analog connections {stereo}

Analog connections (monaural, for subwoofer)

Speaker connections

; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ;

(Orange) (_ i , I

Coaxial digital (75 @/ohms pin-plug) cable

[]

Optical cable

(White)

(Red) (_

Stereo pin-plug cable

(Black) (_

Pin-plug cable

Speaker cables

__i(i!!i!iii!i!ii_ii{{!ii_iiiii{!ii_iiiiii!iii_ili_iii_ii!'!!i!i!i!i!i;!;i_iillill_ii!iiii_i_i!ii!ii_i;!{_!i_iiiii{ii!i_i_,i!i_iiliiii_!iiiii!iiii_i_i!ii!ii_i;!ii!_!i_iiiiiiiiii_i_i!ii!ii_i;!ii!i_}_i}i!_iI!i!i!_iliiii_ii{i_i!_!i_ii_iiii_ii{i_i!_!i_i!;i_iii!!ii_ii!_i_!i!_i_!iiiiiiiiiiiii!!i!13iii!ii!i_i_iii_:_!!i!_i{_il}!_:_Siii_i_i!ii!ii_i;!{_!i_iiiiiiiiii_i_i!ii!ii_i;!{_!i_iiiiiiiiii_i_i!ii!ii_i;!{_!i_iiiiiill!iiii_i_i!ii!ii_i;!{_!i_ii{i!iiii_i_i!ii!ii_i;!{_!i_ii{i!iiii_i_i!ii!ii_i;!{_!i_ii{i!iiii_i_i!ii!ii_i;!{_!i_ii{i!iiii_i_i!ii!ii_i;!{_!i_ii{i!iiii_i_i!ii!ii_i;!{_!i_ii{i!iiii_;i_ii{il;;i_!__i_iiiiiii!iiii_;i_ii{il;;i_!__i_iiiiiii!iiii_;i_ii{il;;i_!__i_iiiiiii!iiii_;i_ii{il;;i_!__i_iiiii

Component video connections

(Green) _ _ _(Y)

(Blue) @ _ _(PB/CB)

(Red) @ _(PR/CR)

Component video cable

[]

S-Video connections

S-Video cable

Video connections

(Yellow) @

75 @/ohms pin-plug video cable

HDMI connections

19-pin HDMI cable

Audio signal: Video signal:

loutputl'nputtoutput

Input Output Input

t Input

Output

The illustration below shows a basic example of installation of the amplifier combined with 6 speakers and a monitor.

Front speakers

Place the front speakers to the sides of the monitor or screen and

as flush with the screen surface as

possible.

The table below shows a typical speaker configuration for the AVR-589.

5.1-channels

3.1-channels

2.1-channels 2-channels

FRONT

L R ,{}, ,C';, ,C}, ,{}, ,C';, ,C}, ,{}, ,C';, ,C},

,_}, ,C';,

SURROUND

L R

\J \J

SUBWOOFERCENTER

Example: 5.1-channels

I Subwoofer I

•_ L • Left R Right

Subwoefer with built-in

amplifier

I Front speakers

A I Center speaker II

Surround speakers !

Carefu cnec_ _ne eft _ ana rlgm _D channels ana - real an(3 -- DlaCI _ oolarltles on ;ne sloeaKers

being cennectea ;e ;ne AVR-S89 ana De sure to

merconnect tne cnannels and ioolarltles correc_ .,

Peel off about 0.03 ft/10 mm _._ of sheathing from the tip of

the speaker cable, then either N

twist the core wire tightly or terminate it.

Turn the speaker terminal _x counterclockwise to loosen _)M

Insert the speaker cable's core wire to the hilt into the

speaker terminal.

Turn the speaker terminal clockwise to tighten it.

When using a banana plug

Tigmen ;ne 3beaKer termlna _;_ inseRing me Danana plug.

before

If the core wires touch the rear panel and the screws etc., or the + sides touch each other, the

)retection circuit will be activated and the power

indicator will flash red at intervals of 0.5 secs. If the protection circuit is activated, the speaker

output is isolated, and the power supply goes to the standby state. If the power supply is turned off, after the power supply cord is withdrawn,

)lease confirm that speaker cable and input cable

are connected. Also, if replaying large sound levels by using

a speaker having an impedance less than that specified (eg, 4 _/ohms), the temperature will rise, and the protection circuit might be activated.

The power supply will go into the standby state,

and the power indicator will flash red at 2 second intervals.

In this case, please switch off the power supply, and wait until the AVR-589 has cooled down, and the surrounding ventilation is good. Even if there are no problems with the surround- ing ventilation and connections, in the event of the protection circuit becoming activated, due to thinking that the AVR-589 has failed, please con- tact DENON Service center after switching off.

" Jse sloeaKers NlIn an _oeaance of 6 _o 16

enms When uslnc front _ ana B speakers

slmul;aneous Jse sloeaKers NIIn at _Deqance

of 12 to 16 _/ehms.

o Connect the speaker cables in such a way that

they do not stick out of the speaker terminals. The protection circuit may be activated if the core wires touch the rear panel or if the + and - sides touch each other (_ "Protection circuit").

oNever touch the speaker terminals while the

power supply is connected. Doing so could result in electric shock.

r DVD player

I AUDIO

i HDMI

OUT

oThe AVR-589 cannot be controlled from another device via the HDMI cable.

Monitor

HDMI

When HDMI input signals are sent to the

monitor as HDMI output, both video and

audio are output to the monitor.

_signal input to the HDIVll I input connector cannot be played

IontheAVR- 89Inputtheaudiosignal

I to the digital audio input connector or I analog audio input connector.

oVideo signals are not output if the input video signals do not match the monitor's resolution. In this case,

switch the DVD player's resolution to a resolution with which the monitor is compatible.

o Use a cable on which the HDMI logo is indicated (a certified HDMI product) for connection to the HDMI

connector. Normal playback may not be possible when using a cable other than one on which the HDMI logo is indicated (a non-HDMI-certified product).

o If the monitor or DVD player does not support Deep Color, deep color signal transfer is not possible. o If the monitor or DVD player does not support xvYCC, xvYCC signal transfer is not possible.

oThe audio and video signals input to the AVR-589's HDMI input connector are output unchanged from

the HDMI output connector. Because of this, the sound is output from the monitor connected using the

HDMI connectors, but in order to take full advantage of the AVR-589's playback sound, turn the TV's

volume down.

o If the connected monitor or DVD player only has a DVI-D connector, use an HDMI/DVI converter cable.

When using a DVI cable, no audio signals are transmitted.

o Use a Deep Color compatible cable for connection to Deep Color compatible devices.

•_ The AVR-589 is equipped for HDMI version 1.3a. This version is compatible with other versions, allowing

connection to all components equipped with an HDMI connector.

•_ The AVR-589 is compatible with 30- and 36-bit Deep Color.

•_ The AVR-589 can be connected to a device equipped with an HDMI output connector using an HDMI

cable.

•_ The AVR-589 is compatible with HDMI Ver. 1.3a Deep Color and xvYCC.

o HDMI video signals are theoretically compatible with the DVI format.

When connecting to a monitor, etc., equipped with a DVI-D connector, connection is possible using an HDMI/DVI converter cable, but depending on the combination of components in some cases the video signals will not be output.

o When connecting using an HDMI/DVI converter adapter, the video signals may not be output properly

due to poor connections with the connected cable, etc.

Select the terminal to use and connect the device.

VIDEO

[Flow of video signals inside the AVR-589]

HDMI

Carefully check the left (L) and right (R) channels and the inputs and outputs, and be sure to interconnect correctly.

*The AVR-589 supports four video input formats:

HDMI, component video, S-video and video. Because video signals are output from the AVR- 589's monitor output terminal in the same format as the video input signals, the monitor output terminal should be of the same type as the terminal used for input.

=The component video connectors may be

indicated differently on your monitor. For details, see the monitor's operating instructions.

oTo play the sound by AVR-589, make analog or

digital audio output connections to AVR-589's

Select the terminal to use and connect the device.

DVD player

i HDMI

AUDIO

OUT

The audio signal input to the HDMI input connector cannot be played on the AVR-589. Input the audio signal to the digital audio

input connector or analog

audio input connector.

audio input connectors.

CZZZZ3

High picture

quality playback HDMI connector

Y Ps/CB PPdCR Y PB/CB PR/CR

Component video

connectors

HDMI connector

Component video

connectors

Monitor

S-Video connector S-Video connector

The same method can be used to connect an HDP (High-Definition Player) such as a Blu-ray Disc

CZZZZ3

Video connector

player.

oWhen using an optical cable for the digital audio connection, make the settings at "System Setup"

- "Input Setup" - "Digital In Assign" (_page 24).

Video input terminals

Monitor output

terminals

Because video signals are output from the AVR-S89's monitor output terminal in the same format as the video input signals, the monitor output terminal should be of the same type as the terminal used for

input,

Select the terminal to use and connect the device.

Use a DENON control dock for iPod (ASD-1 R, ASD-3N or ASD-3W sold separately) to connect the iPod to the AVR-S89. For instructions on the control dock for iPod settings, refer to the control dock for

iPod's operating instructions.

iPod

Select the terminal to use and connect the device.

The audio signal input to the HDMI input connector cannot be

played on the AVR-589. Input the audio signal to the digital audio input

connector or analog audio input connector.

-- TV tuner

VIDEO

I AUDIO

i HDMI

OUT

i o

When using an optical cable for the digital audio connection, make the settings at "System Setup" - "Input Setup" - "Digital In Assign" (_page 24).

* With the default settings, the iPod can be used connected to the

VCR (iPod) connector.

*To assign the iPod to a connector other than VCR (iPod), make

the settings at "System Setup" - "Input Setup" - "iPod Assign" (L_=page 24).

Video/S-Video or Component Video connections are required to playback iPod Video or Photos on TV monitor,

When using a coaxial cable for the digital audio connection, make the settings at "System Setup" - "Input Setup" - "Digital In Assign" (_page 24).

Carefully check the left (L) and right (R) channels and the inputs and outputs, and be sure to interconnect correctly.

Select the terminal to use and connect the device.

+,©

VIDEO AUDIO

Select the terminal to use and connect the device.

CD recorder / MD recorder /

Select the terminal to use and connect the device.

Video camera /

When recording via the AVR-589, the playback device's cable must

be of the same type as the cable used to connect the AVR-589's VCR OUT connector.

Example: TV IN --> S-Video cable : VCR OUT --> S-Video cable

TV IN -->Video cable :VCR OUT --> Video cable

Select the terminal to use and connect the device.

*The AVR-589 is a SIRIUS Satellite Radio Ready ® receiver. You can

receive SIRIUS ® Satellite Radio by connecting to the SiriusConnect Home Tuner and subscribing to the SIRIUS service.

* Plug the SIRIUS connector on the rear panel. * Position the Home Tuner antenna near a south-facing window to

receive the best signal. For details, see "Listening to SIRIUS Satellite Radio Programs"

(L_=_page37).

When making connections, also refer to the operating instructions of the SiriusConnect Home Tuner.

SiriusConneet Home Tuner

When connecting the Optical terminal, set the input Optical terminal allocations for "System Setup" - "Input Setup" - "Digital In Assign",

in "SIRIUS".

Keep the power cord unplugged until the SiriusConnect Home Tuner connection have been completed.

@2006 SIRIUS Satellite Radio Inc. "SIRIUS", the SIRIUS dog logo, and channel names and Iogos are trademarks of SIRIUS Satellite

Radio Inc.

[3 Positioning the Antenna _,

For a consistent satellite signal, the antenna must be positioned .............._

correctly. Use the following map to determine which area you are in ili

and position the antenna accordingly.

oTo play the analog input signals input to the EXT. IN connectors,

press the iNPUT MODE button on the main unit or the JNP[J]" button on the remote control unit and select "EXT. IN" (_page 34).

oThe video signal can be connected in the same way as a DVD player

(_page 11).

oTo play copyright-protected discs, connect the AVR-SS9's EXT.

IN connector with the DVD player's analog multi-channel output

connector.

digital audio.

l '_ When connecting

SKY

WEST EAST

HORIZON

SOUTH

Area 1 : Point the antenna toward the sky in the east, northeast, or

southeast, either through a window or outside.

Area 2 : Point the antenna toward the sky in the north or northeast,

either through a window or outside.

Area 3 : Point the antenna toward the sky in the north or northwest,

either through a window or outside.

Area 4 : Point the antenna toward the sky in the west, northwest, or

southwest, either through a window or outside.

Area 5 : Put the antenna outside and point it straight up.The antenna

cannot be used indoors.

An F-type FM antenna cable plug can be connected directly.

5' i

...............

AM outdoor antenna

AM loop antenna

(supplied)

Direction of broadcasting station

FM antenna'_ _

Ground

75 O/ohms Coaxial cable

FM indoor

antenna

(supplied)

Q AM loop antenna assembly

Remove the vinyl tie and take out

the connection line.

Bend in the reverse direction.

a. With the antenna on top of any

stable surface.

Mount

Installation hole Mount

on wall, etc,

1. Push the lever. 2. Insert the conductor. 3. Return the lever.

=:> =_>

Note to CATV system installer: This reminder is provided to call the CATV system installer's attention to Article 820-40 of the NEC which provides guidelines for proper grounding and, in particular, specifies that the cable

ground shall be connected to the grounding system of the building, as close to the point of cable entry as practical.

b. With the antenna attached to a

wall.

Wait until all connections have been completed before connecting the power cord.

Power cord __

.................... To household

power outlet

[_] [_] (AC120V, 60Hz)

oThese outlets supply power to external

audio equipment.

oThe power supplied from these outlets

turns on and off together with the set's

power switch.

oAudio equipment with a total power

consumption of 120 W (1 A) can be connected.

o Insert the AC plugs securely. Incomplete connections could cause

noise.

o Only use the AC outlets to plug in audio equipment. Do not use

them as power supplies for hairdryers or anything other than audio equipment.

+ 40 hidden pages