Denon AVR-1912 Owners Manual
INTEGRATED NETWORK AV RECEIVER
Basic version
Advanced version
Information
AVR-1912
Owner’s Manual
SAFETY PRECAUTIONS
Basic version
Advanced version
Information
n
IMPORTANT SAFETY
FCC INFORMATION (For US customers)
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION:
TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE
COVER (OR BACK). NO USER-SERVICEABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
The lightning flash with arrowhead symbol, within an equilateral
triangle, is intended to alert the user to the presence of
uninsulated “dangerous voltage” within the product’s enclosure
that may be of sufficient magnitude to constitute a risk of
electric shock to persons.
The exclamation point within an equilateral triangle is intended
to alert the user to the presence of important operating
and maintenance (servicing) instructions in the literature
accompanying the appliance.
WARNING:
TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT
EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE.
CAUTION:
HOT SURFACE. DO NOT TOUCH.
The top surface over the internal heat sink may become hot
Hot
surface
mark
when operating this product continuously.
Do not touch hot areas, especially around the “Hot surface
mark” and the top panel.
INSTRUCTIONS
1. Read these instructions.
2. Keep these instructions.
3. Heed all warnings.
4. Follow all instructions.
5. Do not use this apparatus near water.
6. Clean only with dry cloth.
7. Do not block any ventilation openings.
Install in accordance with the manufacturer’s instructions.
8. Do not install near any heat sources such as radiators, heat registers,
stoves, or other apparatus (including amplifiers) that produce heat.
9. Do not defeat the safety purpose of the polarized or grounding-type plug. A
polarized plug has two blades with one wider than the other. A grounding
type plug has two blades and a third grounding prong. The wide blade or the
third prong are provided for your safety. If the provided plug does not fit into
your outlet, consult an electrician for replacement of the obsolete outlet.
10. Protect the power cord from being walked on or pinched particularly at
plugs, convenience receptacles, and the point where they exit from the
apparatus.
11. Only use attachments/accessories specified by the manufacturer.
12. Use only with the cart, stand, tripod, bracket, or table
specified by the manufacturer, or sold with the apparatus.
When a cart is used, use caution when moving the cart/
apparatus combination to avoid injury from tip-over.
13. Unplug this apparatus during lightning storms or when
unused for long periods of time.
14. Refer all servicing to qualified service personnel.
Servicing is required when the apparatus has been damaged in any way,
such as power-supply cord or plug is damaged, liquid has been spilled or
objects have fallen into the apparatus, the apparatus has been exposed to
rain or moisture, does not operate normally, or has been dropped.
15. Batteries shall not be exposed to excessive heat such as sunshine, fire or
the like.
CAUTION:
To completely disconnect this product from the mains, disconnect the plug
from the wall socket outlet.
The mains plug is used to completely interrupt the power supply to the unit
and must be within easy access by the user.
1. COMPLIANCE INFORMATION
Product Name: Integrated Network AV Receiver
Model Number: AVR-1912
This product complies with Part 15 of the FCC Rules. Operation is subject
to the following two conditions: (1) this product may not cause harmful
interference, and (2) this product must accept any interference received,
including interference that may cause undesired operation.
Denon Electronics (USA), LLC
(a D&M Holdings Company)
100 Corporate Drive
Mahwah, NJ 07430-2041
Tel. (800) 497-8921
2. IMPORTANT NOTICE: DO NOT MODIFY THIS PRODUCT
This product, when installed as indicated in the instructions contained
in this manual, meets FCC requirements. Modification not expressly
approved by DENON may void your authority, granted by the FCC, to use
the product.
3. IMPORTANT
When connecting this product to network hub or router, use only a
shielded STP or ScTP LAN cable which is available at retailer.
Follow all installation instructions. Failure to follow instructions could void
your authority, granted by the FCC, to use the product.
4. NOTE
This product has been tested and found to comply with the limits for
a Class B digital device, pursuant to Part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation.
This product generates, uses and can radiate radio frequency energy and,
if not installed and used in accordance with the instructions, may cause
harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this
product does cause harmful interference to radio or television reception,
which can be determined by turning the product OFF and ON, the user
is encouraged to try to correct the interference by one or more of the
following measures:
•Reorientorrelocatethereceivingantenna.
•Increasetheseparationbetweentheequipmentandreceiver.
•Connect the productintoan outlet on a circuit differentfrom that to
which the receiver is connected.
•Consultthelocalretailerauthorizedtodistributethistypeofproductor
an experienced radio/TV technician for help.
For Canadian customers:
This Class B digital apparatus complies with Canadian ICES-003.
I
NOTES ON USE
Basic version
Advanced version
Information
n
n CAUTIONS ON INSTALLATION
WARNINGS
•Avoid high temperatures.
Allow for sufficient heat dispersion when installed in a rack.
•Handle the power cord carefully.
Hold the plug when unplugging the cord.
•Keep the unit free from moisture, water, and dust.
•Unplug the power cord when not using the unit for long periods of time.
•Do not obstruct the ventilation holes.
•Do not let foreign objects into the unit.
•Do not let insecticides, benzene, and thinner come in contact with the unit.
•Never disassemble or modify the unit in any way.
•Ventilation should not be impeded by covering the ventilation openings
with items, such as newspapers, tablecloths or curtains.
•Naked flame sources such as lighted candles should not be placed on
the unit.
•Observe and follow local regulations regarding battery disposal.
•Do not expose the unit to dripping or splashing fluids.
•Do not place objects filled with liquids, such as vases, on the unit.
•Do not handle the mains cord with wet hands.
•When the switch is in the OFF (STANDBY) position, the equipment is not
completely switched off from MAINS.
•The equipment shall be installed near the power supply so that the power
supply is easily accessible.
z
z z
z
Wall
z For proper heat dispersal, do not install this unit in a confined
space, such as a bookcase or similar enclosure.
•More than 12 in. (0.3 m) is recommended.
•Do not place any other equipment on this unit.
II
Getting started
Basic version
Advanced version
Information
Thank you for purchasing this DENON product. To ensure proper operation, please read this owner’s manual carefully before using the product.
After reading them, be sure to keep them for future reference.
Contents
Getting started ·············································································· 1
Accessories ··················································································1
Features ························································································ 2
Cautions on handling ····································································2
Basic version ············································································3
Connections ··················································································· 4
Important information ··································································· 4
Connecting an HDMI-compatible device ······································ 6
Connecting a TV············································································8
Connecting a Blu-ray Disc player/DVD player ······························· 8
Connecting a set-top box (Satellite tuner/Cable TV) ·····················9
Connecting a digital camcorder ····················································9
Connecting a control dock for iPod ············································· 10
Connecting an iPod or USB memory device to the USB port ·····10
Connecting an antenna ······························································· 11
Connecting a CD player ······························································ 11
Connecting to a home network (LAN) ········································ 12
Settings ························································································ 13
Set up speakers (Audyssey® Auto Setup) ·································13
Making the network settings (Network Setup) ···························19
Playback (Basic operation) ························································· 20
Important information ································································· 20
Playing a Blu-ray Disc player/DVD player ···································· 21
Playing a CD player ····································································· 21
Playing an iPod············································································22
Tuning in radio stations ······························································· 26
Playing a network audio ······························································ 28
Playing a USB memory device ····················································42
Selecting a listening mode (Surround mode) ··························44
Selecting a listening mode··························································44
Advanced version ·······························································48
Speaker installation/connection (Advanced connection) ······· 49
Install ··························································································49
Connect ······················································································51
Set up speakers ·········································································· 56
Playback (Advanced operation) ················································· 58
Convenient functions ·································································· 58
Playback in ZONE2 (Separate room) ········································ 68
Audio output ··············································································· 68
Playback ······················································································ 68
Quick select function ·································································· 69
Sleep timer function ···································································69
How to make detailed settings ·················································· 70
Menu map ··················································································70
Examples of menu screen displays ············································ 71
Examples of menu and front display ··········································72
Inputting characters ··································································· 73
Audio Adjust ···············································································75
Information ·················································································81
System Setup ············································································· 82
Input Setup ················································································· 95
Operating the connected devices by remote control unit ····101
Operating AV devices ······························································· 101
Registering preset codes ·························································· 102
Operating devices ····································································· 104
Specifying the zone used with the main remote control unit ··· 106
Resetting the remote control unit ·············································106
Information ···········································································107
Part names and functions·························································108
Front panel ················································································ 108
Display ······················································································ 109
Rear panel ················································································· 110
Remote control unit ·································································· 111
Other information ·····································································113
Trademark information ······························································113
Surround ··················································································· 114
Relationship between video signals and monitor output ·········· 118
Explanation of terms ································································· 119
Troubleshooting ········································································ 122
Resetting the microprocessor ··················································125
Specifications ············································································126
Accessories
Check that the following parts are supplied with the product.
q Getting Started ........................................................................ 1
w CD-ROM (Owner’s manual) .................................................... 1
e Warranty (for North America model only) ................................ 1
r Service network list ................................................................. 1
t Remote control unit (RC-1156) ................................................ 1
y R6/AA batteries ....................................................................... 2
u Setup microphone
(DM-A409, Cord length: Approx. 19.7 ft / 6.0 m) .................... 1
i AM loop antenna ..................................................................... 1
o FM indoor antenna .................................................................. 1
t
i o
u
1
Features
Basic version
Advanced version
Information
Cautions on handling
Fully discrete, identical quality and power for all
7 channels (125 W x 7ch)
The unit is equipped with a power amplifier that reproduces highfidelity sound in surround mode with equal quality and power for all
channels, true to the original sound.
The power amplifier circuit adopts a discrete-circuit configuration
that achieves high-quality surround sound reproduction.
Supports internet radio, music, and photograph
streaming
Supports AirPlay® (vpage62)
When connected to a network, this unit can play audio files and still
images such as photographs that are stored on your computer. You
can also listen to internet radio and a host of other online music
sources that use network technology. This unit also supports
AirPlay that lets you stream your music library from an iPhone,
iPad, iPod touch or iTunes.
Compatible with “Denon Remote App” for
performing basic operations of the unit with an
iPhone or iPod touch
“Denon Remote App” is application software that allows you to
perform basic operations with an iPhone or iPod touch such as
turning the unit ON/OFF, controlling the volume, and switching the
source.
z1 Download “Denon Remote App” from iTunes® App Store.
The unit needs to be connected to a LAN and the iPhone/iPod
touch needs to be connected to the same network by Wi-Fi
(wireless LAN).
z1
Easy to use, Graphical User Interface
This unit is equipped with an easy to see “Graphical User Interface”
that uses menu displays and levels. The use of level displays
increases operability of the this unit.
Direct play for iPod® and iPhone® via USB
(vpage10)
Music data from an iPod can be played back if you connect the USB
cable supplied with the iPod via the USB port of this unit, and also
an iPod can be controlled with the remote control unit for this unit.
When an iPod is connected, merely pressing iPod 1 on the main
unit starts playback of music from the iPod.
Supports HDMI 1.4a with 3D, ARC, Deep Color,
“x.v.Color”, Auto Lip Sync and HDMI control
function (vpage6)
This unit can output 3D video signals input from a Blu-ray Disc
player to a TV that supports a 3D system. This unit also supports
the ARC (Audio Return Channel) function, which reproduces TV
sound with this unit via an HDMI cable used for connecting the
unit and a TVz2.
z2 The TV should support the ARC function.
6-HDMI inputs and 1-output
The unit is equipped with 6 HDMI input connectors for connecting
devices with HDMI connectors, such as a Blu-ray Disc player,
game machine, HD video camera, etc.
•Before turning the power on
Check once again that all connections are correct and that there are
no problems with the connection cables.
•Power is supplied to some of the circuitry even when the unit is
set to the standby mode. When going on vacation or leaving home
for long periods of time, be sure to unplug the power cord from the
power outlet.
•About condensation
If there is a major difference in temperature between the inside of
the unit and the surroundings, condensation (dew) may form on
the operating parts inside the unit, causing the unit not to operate
properly.
If this happens, let the unit sit for an hour or two with the power
turned off and wait until there is little difference in temperature
before using the unit.
•Cautions on using mobile phones
Using a mobile phone near this unit may result in noise. If that
occurs, move the mobile phone away from this unit when it is in use.
•Moving the unit
Turn off the power and unplug the power cord from the power
outlet. Next, disconnect the connection cables to other system units
before moving the unit.
•About care
•Wipe the cabinet and control panel clean with a soft cloth.
•Follow the instructions when using a chemical cleaner.
•Benzene, paint thinner or other organic solvents as well as
insecticide may cause material changes and discoloration if brought
into contact with the unit, and should therefore not be used.
Setup wizard, providing easy-to-follow setup
instructions
First select the language when prompted. Then simply follow the
instructions displayed on the TV screen to set up the speakers,
network, etc.
High definition audio support
The unit is equipped with a decoder which supports high-quality
digital audio format for Blu-ray Disc players such as Dolby TrueHD,
DTS-HD Master Audio, etc.
2
Basic
Basic version
Advanced version
Information
Basic version
version
Basic version
Here, we explain the connections and basic operation methods for this unit.
F Connections vpage4
F Settings vpage13
F Playback (Basic operation) vpage20
F Selecting a listening mode (Surround mode) vpage44
Connection
Playback
Connection
Playback
Connection
Playback
Connection
Playback
Connection
Playback
Connection
Playback
vpage7, 8
–
vpage7, 8
vpage21
vpage7, 9
–
vpage10
vpage24
vpage7
–
vpage11
vpage26
Connection
Playback
Connection
Playback
Connection
Playback
Connection
Playback
Connection
Playback
Connection
Playback
For speaker connections, see page51, C page 6 “Connecting the speakers”.
3
vpage7, 8
vpage21
vpage11
vpage21
vpage10
vpage22
vpage10
vpage42
vpage9
–
vpage12
vpage28
Connections
Basic version
Advanced version
Information
Basic version
vSee overleaf
Important information
•Make connections as follows before using this unit. Select an
appropriate connection type according to the devices to be
connected.
•You may need to make some settings on this unit depending
on the connection method. Refer to each description for more
information.
•Select the cables (sold separately) according to the devices
being connected.
NOTE
•Do not plug in the power cord until all connections have been
completed. (When the Setup wizard is running, follow the instructions
in the Setup wizard screen for making connections.)
•When running the Setup wizard, turn off the power supply of
connected devices.
•When making connections, also refer to the operating instructions of
the other devices being connected.
•Be sure to connect the left and right channels properly (left with left,
right with right).
•Do not bundle power cords together with connection cables. Doing
so can result in noise.
Converting input video signals for output (Video conversion function)
This unit is equipped with four types of video input connectors (HDMI, Component video, S-Video and video) and two types of video output
connectors (HDMI and video).
Use the connectors corresponding to the devices to be connected.
This function automatically converts various formats of video signals input to this unit into the formats used to output the video signals from
this unit to a monitor.
GFlow of video signals for MAIN ZONEH
Video device
Output
HDMI connector
Input
(IN)
HDMI connector
This unit
Output
(MONITOR OUT)
HDMI
connector
Monitor (TV)
Input
HDMI connector
Component video
connectors
S-Video connector
Video connector
•The video conversion function supports the NTSC, PAL, SECAM, NTSC 4.43, PAL-N, PAL-M and PAL-60 formats.
•Resolutions of HDMI-compatible TVs can be checked at “HDMI Monitor Information” (vpage81).
Component video
connectors
S-Video
connector
Video connector
Video connector
Video connector
NOTE
•HDMI signals cannot be converted into analog signals.
•Component video input signals cannot be converted into Video format.
•When a non-standard video signal from a game machine or some other source is input, the video conversion function might not operate.
4
Important information
Basic version
Advanced version
Information
Basic version
Examples of screen display
•Menu screen •Status display screen
When the input source is
switched.
Menu
Audio Adjust
Information
Setup Wizard
System Setup
Input Setup
Surr.Parameter
Tone
AudysseySettings
Manual EQ
RESTORER
Audio Delay
SOURCE :BD
MODE
[Auto]
:STEREO
Status display: The operating status appears briefly on the screen
when the input source is switched or the volume is
changed.
NOTE
•If you operate the menu while playing back 3D video content or computer’s resolution (e.g. VGA), the
playback video is replaced by the menu screen. The playback video is not displayed behind the menu
screen.
•This unit does not show the status display while playing back 3D video content or computer’s resolution
(e.g. VGA).
•The menu screen and status display are displayed when this unit and a TV are connected by HDMI.
Furthermore, the menu screen and status display are not displayed when this unit and a TV are connected
by VIDEO.
When the volume is adjusted.
Master Volume -55.5dB
5
Connecting an HDMI-compatible device
Basic version
Advanced version
Information
Basic version
vSee overleaf
You can connect up to seven HDMI-compatible devices (6-inputs/1-output) to the unit.
HDMI function
This unit supports the following HDMI functions:
•3D
•Deep Color (vpage119)
•Auto Lip Sync (vpage86, 119)
•“x.v.Color”, sYCC601 color, Adobe RGB color, Adobe YCC601 color (vpage119, 120, 121)
•High definition digital audio format
•ARC (Audio Return Channel)
•Content Type
•CEC (HDMI control)
Copyright protection system
In order to play back digital video and audio such as BD-Video or DVD-Video via HDMI connection, both
this unit and TV or the player need to support the copyright protection system known as HDCP (Highbandwidth Digital Content Protection System). HDCP is copyright protection technology comprised of
data encryption and authentication of the connected AV devices. This unit supports HDCP.
•If a device that does not support HDCP is connected, video and audio are not output correctly. Read
the owner’s manual of your television or player for more information.
About HDMI cables
•When a device supporting Deep Color is connected, use a cable compatible with “High Speed HDMI
cable” or “High Speed HDMI cable with Ethernet”.
•When the ARC function is used, connect a device with a ”Standard HDMI cable with Ethernet” or “High
Speed HDMI cable with Ethernet” for HDMI 1.4a.
HDMI control function (vpage58)
This function allows you to operate external devices from the unit and operate the unit from external
devices.
NOTE
•The HDMI control function may not work depending on the device it is connected to and its settings.
•You cannot operate a TV or Blu-ray Disc player/DVD player that is not compatible with the HDMI control
function.
About 3D function
This unit supports input and output of 3D (3 dimensional) video signals of HDMI 1.4a.
To play back 3D video, you need a TV and player that provide support for the HDMI 1.4a 3D function and
a pair of 3D glasses.
NOTE
•When playing back 3D video, refer to the instructions provided in the manual of your playback device
together with this manual.
•If you operate the menu while playing back 3D video content, the playback video is replaced by the menu
screen. The playback video is not displayed behind the menu screen.
•This unit does not show the status display while playing back 3D video content.
•If 3D video with no 3D information is input, the menu screen and status display on this unit are displayed
over the playback video.
•If 2D video is converted to 3D video on the television, the menu screen and status display on this unit
are not displayed correctly. To view the menu screen and status display on this unit correctly, turn the
television setting that converts 2D video to 3D video off.
About ARC (Audio Return Channel) function
The Audio Return Channel in HDMI 1.4a enables a TV, via a single HDMI cable, to send audio data “upstream”
to this unit.
NOTE
•To enable the ARC function, set “HDMI Control” to “ON” (vpage86).
•When connecting a TV that does not support the ARC function, a separate connection using an audio
cable is required. In this case, refer to “Connecting a TV” (vpage8) for the connection method.
About Content Type
HDMI 1.4a enables simple, automated picture setting selection with no user intervention.
NOTE
To enable the Content Type, set “Video Mode” to “Auto” (vpage98).
6
Cables used for connections
Basic version
Advanced version
Information
Basic version
Audio and video cable (sold separately)
HDMI cable
•This interface allows transfer of digital video signals and digital audio signals over a single HDMI cable.
Blu-ray
Disc
player
HDMI
OUT
DVD
player
HDMI
OUT
Set-top
box
HDMI
OUT
Game
console 1
HDMI
OUT
Game
console 2
HDMI
OUT
Digital
camcorder
HDMI
OUT
TV
HDMI
IN
Connecting an HDMI-compatible device
•When this unit is connected to other devices with HDMI cables, connect this unit and TV also with an
HDMI cable.
•When connecting a device that supports Deep Color, please use a “High Speed HDMI cable” or “High
Speed HDMI cable with Ethernet”.
•Video signals are not output if the input video signals do not match the monitor’s resolution. In this case,
switch the Blu-ray Disc/DVD player’s resolution to a resolution with which the monitor is compatible.
•When this unit and monitor are connected with an HDMI cable, if the monitor is not compatible with
HDMI audio signal playback, only the video signals are output to the monitor.
NOTE
The audio signal from the HDMI output connector (sampling frequency, number of channels, etc.) may be
limited by the HDMI audio specifications of the connected device regarding permissible inputs.
Connecting to a device equipped with a DVI-D connector
When an HDMI/DVI conversion cable (sold separately) is used, the HDMI video signals are converted to
DVI signals, allowing connection to a device equipped with a DVI-D connector.
NOTE
•No sound is output when connected to a device equipped with a DVI-D connector. Make separate audio
connections.
•Signals cannot be output to DVI-D devices that do not support HDCP.
•Depending on the combination of devices, the video signals may not be output.
nSettings related to HDMI connections
Set as necessary. For details, see the respective reference pages.
Input Assign (vpage97)
Set this to change the HDMI input connector to which the input source is assigned.
HDMI Setup (vpage86)
Make settings for HDMI video/audio output.
•Auto Lip Sync •HDMI Audio Out •HDMI Control
•Standby Source •P.Off Control
NOTE
The audio signal input from the HDMI input connector can be output as an output signal from the HDMI
output connector by setting the HDMI audio output destination to TV.
Audio signals input via the Analog/Coaxial/Optical input connectors cannot be output from the HDMI
output connector.
7
Connecting a TV
Basic version
Advanced version
Information
Basic version
•Select the connector to use and connect the device.
•For video connections, see “Converting input video signals for output (Video conversion function)”
(vpage4).
•For instructions on HDMI connections, see “Connecting an HDMI-compatible device” (vpage6).
To listen to TV audio through this device, use the optical digital connection.
NOTE
The optical connection is not required when a TV compatible with the ARC function (Audio Return Channel
HDMI 1.4a standard function) is connected to this unit via an HDMI connection.
For details, see “About ARC (Audio Return Channel) function” (vpage 6) or refer to the instruction
manual for your TV.
Cables used for connections
Video cable (sold separately)
Video cable
Audio cable (sold separately)
Optical cable
TV
VIDEO
VIDEO
IN
AUDIO
OPTICAL
OUT
Connecting a Blu-ray Disc player/DVD player
•You can enjoy video and audio from a Blu-ray Disc or DVD.
•Select the connector to use and connect the device.
•For instructions on HDMI connections, see “Connecting an HDMI-compatible device” (vpage6).
Cables used for connections
Video cable (sold separately)
Video cable
Audio cables (sold separately)
Audio cable
DVD player
VIDEO
VIDEO
OUT
AUDIO
AUDIO
OUT
L
L
L
R
Blu-ray Disc
player
AUDIO
AUDIO
RL
R
R
OUT
L
L
RL
R
R
L
R
in Set as Necessary
Set this to change the digital input connector or component video input connector to which the input
source is assigned.
“Input Assign” (vpage97)
in Set as Necessary
Set this to change the digital input connector or component video input connector to which the input
source is assigned.
“Input Assign” (vpage97)
When you want to play back HD Audio (Dolby TrueHD, DTS-HD, Dolby Digital Plus, DTS Express) and Multichannel PCM with this unit, use an HDMI connection (vpage 6 “Connecting an HDMI-compatible
device”).
8
Connecting a set-top box (Satellite tuner/Cable TV)
Basic version
Advanced version
Information
Basic version
•You can watch satellite or cable TV.
•Select the connector to use and connect the device.
•For instructions on HDMI connections, see “Connecting an HDMI-compatible device” (vpage6).
Cables used for connections
Video cable (sold separately)
Video cable
Component
video cable
Connecting a digital camcorder
•You can enjoy video and audio from a digital camcorder.
•For instructions on HDMI connections, see “Connecting an HDMI-compatible device” (vpage6).
Cables used for connections
Video cable (sold separately)
Video cable
Audio cable (sold separately)
Audio cable
L
R
L
R
Audio cables (sold separately)
Audio cable
L
R
L
R
Coaxial
digital cable
Satellite tuner/Cable TV
COAXIAL
OUT
AUDIO
AUDIO
OUT
L
L
RL
R
R
Y P
OUT
VIDEO
B PR
COMPONENT VIDEO
VIDEO
OUT
in Set as Necessary
Set this to change the digital input connector or component video input connector to which the input
source is assigned.
“Input Assign” (vpage97)
Digital camcorder
AUDIOVIDEO
VIDEO
OUT
AUDIO
OUT
L
L
RL
R
R
in Set as Necessary
Set this to change the digital input connector or component video input connector to which the input
source is assigned.
“Input Assign” (vpage97)
You can enjoy games by connecting a game machine via the V.AUX input connector. In this case, select
the input source to “V.AUX”.
NOTE
When a non-standard video signal from a game machine or some other source is input, the video conversion
function might not operate. In this case, use the monitor output of the same connector as the input.
9
Connecting a control dock for iPod
Basic version
Advanced version
Information
Basic version
•Connect a control dock for iPod to the unit to enjoy video and music stored on an iPod.
•For a control dock for iPod, use ASD-1R or ASD-11R made by DENON (sold separately).
•For instructions on the control dock for iPod settings, refer to the control dock for iPod’s operating
instructions.
Control dock for iPod
ASD-11R
R
Use the AV/Control
Cable supplied with
the DENON control
dock for iPod.
L
R
L
Connecting an iPod or USB memory device to the USB port
You can enjoy music stored on an iPod or USB memory device.
Cables used for connections
To connect an iPod to this unit, use the USB cable supplied with the iPod.
iPod
USB memory
device
or
•When you want to play back a video file stored on an iPod, use a DENON control dock for iPod (ASD-1R
and ASD-11R, sold separately) (vpage10 “Connecting a control dock for iPod”).
•With iPods, playback is possible with iPhone, iPod touch, classic and nano released from the 5th-generation
of iPods. For details, check page24.
•DENON does not guarantee that all USB memory devices will operate or receive power. When using
a portable USB connection type HDD of the kind to which an AC adapter can be connected to supply
power, use the AC adapter.
NOTE
•USB memory devices will not work via a USB hub.
•Do not use an extension cable when connecting a USB memory device. This may cause radio interference
with other devices.
•This unit does not support playback on an iPad. Do not connect an iPad to the unit.
•When connecting an iPhone to this unit, keep the iPhone at least 20 cm away from this unit. If the iPhone
is kept closer to this unit and a telephone call is received by the iPhone, noise may be output from this
device.
10
Connecting an antenna
Basic version
Advanced version
Information
Basic version
•Connect the FM antenna or AM loop antenna supplied with the unit
to enjoy listening to radio broadcasts.
•After connecting the antenna and receiving a broadcast signal
(vpage 26 “Listening to FM/AM broadcasts”), fix the antenna
with tape in a position where the noise level becomes minimal.
Direction of broadcasting station
FM outdoor
AM loop antenna
(supplied)
White
AM outdoor
antenna
w eq
Black
Ground
antenna
75 Ω coaxial
cable
FM indoor
antenna
(supplied)
nAM loop antenna assembly
Put the stand section
1
through the bottom of the
loop antenna from the
rear and bend it forward.
Insert the projecting part
2
into the square hole in
the stand.
Loop
antenna
Stand
Square
hole
Projecting
part
nUsing the AM loop antenna
Suspending on a wall
Suspend directly on a wall without assembling.
Nail, tack, etc.
Standing alone
Use the procedure shown above to assemble.
NOTE
•Do not connect two FM antennas simultaneously.
•Even if an external AM antenna is used, do not disconnect the AM
loop antenna.
•Make sure the AM loop antenna lead terminals do not touch metal
parts of the panel.
•If the signal has noise interference, connect the ground terminal
(GND) to reduce noise.
•If you are unable to receive a good broadcast signal, we recommend
installing an outdoor antenna. For details, inquire at the retail store
where you purchased the unit.
Connecting a CD player
•You can enjoy CD sound.
•Select the connector to use and connect the device.
Cables used for connections
Audio cable (sold separately)
Audio cable
CD player
AUDIO
AUDIO
OUT
L
L
RL
R
R
L
R
in Set as Necessary
Set this to change the digital input connector to which the input
source is assigned.
“Input Assign” (vpage97)
L
R
11
Connecting to a home network (LAN)
Basic version
Advanced version
Information
Basic version
•This unit lets you play via your home network (LAN) music files
stored on a computer and music content such as that from Internet
radio.
You can also operate this unit from a computer using the Web
control function.
•You can update by downloading the latest firmware from the
DENON website.
For more information, on the menu, select “Firmware Update”
(vpage93).
•See “Network Setup” on the menu (vpage 88) for more
information on network setting.
Cables used for connections
Cable (sold separately)
Ethernet
cable
Computer
Modem
Internet
Required system
nBroadband internet connection
nModem
Device that connects to the broadband circuit and conducts
communications on the Internet.
A type that is integrated with a router is also available.
nRouter
When using this unit, we recommend you use a router equipped
with the following functions:
•Built-in DHCP server
This function automatically assigns IP addresses on the LAN.
•Built-in 100BASE-TX switch
When connecting multiple devices, we recommend a switching
hub with a speed of 100 Mbps or greater.
nEthernet cable (CAT-5 or greater recommended)
•Use only shielded STP or ScTP LAN cable which is available at
retailer.
•Some flat type Ethernet cables are easily affected by noise.
We recommend using a normal type cable.
NOTE
•A contract with an ISP is required to connect to the Internet.
No additional contract is needed if you already have a broadband
connection to the Internet.
•The types of routers that can be used depend on the ISP. Contact an
ISP or a computer shop for details.
•DENON assumes no responsibility whatsoever for any
communication errors or troubles resulting from customer’s
network environment or connected devices.
•This unit is not compatible with PPPoE. A PPPoE-compatible router
is required if you have a contract for a type of line set by PPPoE.
•Do not connect an ETHERNET connector directly to the LAN port/
Ethernet connector on your computer.
•To listen to audio streaming, use a router that supports audio
streaming.
To WAN side
To LAN port
To LAN port
Router
For connections to the Internet, contact an ISP (Internet
Service Provider) or a computer shop.
LAN port/
Ethernet
connector
•If you have an Internet provider contract for a line on which network
settings are made manually, make the settings at “Network Setup”
(vpage88).
•With this unit, it is possible to use the DHCP and Auto IP functions
to make the network settings automatically.
•When using this unit with the broadband router’s DHCP function
enabled, this unit automatically performs the IP address setting and
other settings.
When using this unit connected to a network with no DHCP
function, make the settings for the IP address, etc., at “Network
Setup” (vpage88).
•When setting manually, check the setting contents with the network
administrator.
12
Settings
Basic version
Advanced version
Information
Basic version
vSee overleaf
Here, we explain “Audyssey® Auto Setup”, which allows you to
automatically make the optimal settings for your speakers, and
“Network Setup”, which allows you to connect this unit to a home
network (LAN).
This unit lets you play via your home network (LAN) music files stored
on a computer and music content such as that from Internet radio.
n Set up speakers (Audyssey® Auto Setup)
(vpage13)
n Making the network settings (Network Setup)
(vpage19)
Playback (Basic operation) (vpage20)
Selecting a listening mode (Surround mode)
(vpage44)
Playback (Advanced operation) (vpage58)
Set up speakers (Audyssey® Auto Setup)
The acoustic characteristics of the connected speakers and
listening room are measured and the optimum settings are made
automatically. This is called “Audyssey® Auto Setup”.
To perform measurement, place the setup microphone in
multiple locations all around the listening area. For best results,
we recommend you measure in six positions, as shown in the
illustration (up to six positions).
•When performing Audyssey® Auto Setup, Audyssey MultEQ®/
Audyssey Dynamic EQ®/Audyssey Dynamic Volume® functions
become active (vpage78, 79).
•To set up the speakers manually, use “Speaker Setup”
(vpage83) on the menu.
NOTE
•Make the room as quiet as possible. Background noise can disrupt
the room measurements. Close windows, silence cell phones,
televisions, radios, air conditioners, fluorescent lights, home
appliances, light dimmers, or other devices as measurements may
be affected by these sounds.
•Cell phones should be placed away from all audio electronics during
the measurement process as Radio Frequency Interference (RFI)
may cause measurement disruptions (even if the cell phone is not
in use).
•Do not unplug the setup microphone from the main unit until
Audyssey® Auto Setup is completed.
•Do not stand between the speakers and setup microphone or allow
obstacles in the path while the measurements are being made. This
will cause inaccurate readings.
•Loud test sounds may be played during Audyssey® Auto setup. This
is part of normal operation. If there is background noise in room,
these test signals will increase in volume.
•Operating
will cancel the measurements.
•Measurement cannot be performed when
headphones are connected.
M df during the measurements
About setup microphone placement
•Measurements are performed by placing the setup microphone
successively at multiple positions throughout the entire listening
area, as shown in GExample qH. For best results, we recommend
you measure in six positions, as shown in the illustration (up to six
positions).
•Even if the listening environment is small as shown in GExample wH,
measuring at multiple points throughout the listening environment
results in more effective correction.
GExample qH GExample wH
FL SW C FR
( : Measuring positions)
M
*
FL Front speaker (L) SW Subwoofer
FR Front speaker (R) SL Surround speaker (L)
C Center speaker SR Surround speaker (R)
SRSL
FL SW C FR
( : Measuring positions)
M
*
SRSL
About the main listening position (*M)
The main listening position is the position where listeners would
normally sit or where one would normally sit alone within the listening
environment. Before starting Audyssey® Auto Setup, place the setup
microphone in the main listening position. Audyssey MultEQ® uses
the measurements from this position to calculate speaker distance,
level, polarity, and the optimum crossover value for the subwoofer.
13
Set up speakers (Audyssey® Auto Setup)
Basic version
Advanced version
Information
Basic version
vSee overleaf
1
Mount the setup microphone on a tripod or stand
and place it in the main listening position.
When placing the setup microphone, adjust the height of the
sound receptor to the level of the listener’s ear.
If you do not have a tripod or stand, set up the microphone on, for
example, a seat without a back.
NOTE
•Do not hold the setup microphone in your hand during
measurements.
•Avoid placing the setup microphone close to a seat back or wall as
sound reflections may give inaccurate results.
Set up the microphone
Sound receptor
Setup
microphone
2
If using a subwoofer capable of the following
adjustments, set up the subwoofer as shown below.
n When using a subwoofer with a direct mode
Set the direct mode to “On” and disable the volume adjustment
and crossover frequency setting.
n When using a subwoofer without a direct mode
Make the following settings:
•Volume : “12 o’clock position”
•Crossover frequency : “Maximum/Highest Frequency”
•Low pass filter : “Off”
•Standby mode : “Off”
Set up the subwoofer
3
Press ZONE SELECT to switch the zone mode to
Set up the remote control unit
n Set up the zone mode
J (MAIN ZONE).
The J indicator lights.
Press ZONE SELECT
n Set up the operation mode
Press AMP to set the remote control unit to AMPoperation mode.
Press AMP
14
Set up speakers (Audyssey® Auto Setup)
Basic version
Advanced version
Information
Basic version
vSee overleaf
STEP 1
Preparation
Connect the setup microphone to the SETUP MIC
4
jack of this unit.
When the setup microphone is
connected, the following screen is
displayed.
Audyssey Auto Setup
Preparation
Connect the speakers and place then according
to the recommendations in the manual.
Next
MultEQ
[RETURN][ENTER] Enter Cancel
Use ui to select “Auto Setup Start” and then press
6
ENTER.
Audyssey Auto Setup MultEQ
Preparation
Set the following items
if necessary.
Amp Assign
Channel Select
Auto Setup Start
[RETURN][ENTER] Enter Cancel
Here, we explain setup using the example of 5.1-channel speaker
playback.
For settings other than 5.1-channel surround, select “Amp Assign”
and perform step 4 to 5 of “Set up “Amp Assign”” (vpage56).
If unused channels are set with “Channel Select”, measuring time
can be shortened. For setting, perform steps 7 to 11 of “Set up
“Channel Select”” (vpage57).
STEP 2
Detect & Measure (Main)
•In STEP 2, you will perform measurements at the main listening
position.
•This step automatically checks the speaker configuration and speaker
size, and calculates the channel level, distance, and crossover
frequency.
It also corrects distortion in the listening area.
Select “Measure” and then press ENTER.
7
When measuring begins, a test tone is output from each
speaker.
•Measurement requires several minutes.
The detected speakers are displayed.
8
•The illustration below shows an example of when the front
speakers, center speaker, subwoofer, and surround speakers have
been detected.
Audyssey Auto Setup MultEQ
Detect Check
Front
Center
Subwoofer
Surround
Yes
Yes
Yes
Yes
5
Select “Next” and then press
ENTER.
15
Retry
Next Measure
[ENTER] Enter
[RETURN] Cancel
NOTE
If a connected speaker is not displayed, the speaker may not be
connected correctly. Check the speaker connection.
Use ui to select “Next → Measure” and then press
9
ENTER.
Set up speakers (Audyssey® Auto Setup)
Basic version
Advanced version
Information
Basic version
vSee overleaf
STEP 2 (Continued)
Detect & Measure (Main)
NOTE
If “Caution” is displayed:
Go to “Error messages” (vpage 18),
check any related items, and perform the
necessary procedures.
If the problem is resolved, return and restart
“Audyssey® Auto Setup”.
When performing Audyssey® Auto Setup over
again
Press ui to select “Retry”, and then press ENTER.
When measuring has stopped
q Press RETURN B, to the “Cancel Auto Setup?” prompt is
displayed.
w Press o to select “Yes”, then press ENTER.
Setting up the speakers again
Repeat the operation from step 4 of
STEP 1 Preparation
.
STEP 3
Measure (2nd – 6th)
•In STEP 3, you will perform measurements at multiple positions (two
to six positions) other than the main listening position.
•Just one position can be measured but measuring multiple positions
increases the accuracy of the correction of acoustic distortion within
the listening area.
Move the setup microphone to
10
position 2, use ui to select
“Measure”, and then press
ENTER.
The measurement of the second
position starts. Measurements can be
made in up to six positions.
Audyssey Auto Setup MultEQ
Measure (2nd)
Please place the
microphone at ear
height at 2nd
listening position.
Measure
Next Calculate
[RETURN][ENTER] Enter Cancel
STEP 4
Calculate
On the
12
Calculate”, and then press ENTER.
Measuring results are analyzed, and the frequency response of
each speaker in the listening room is determined.
•Analysis takes several minutes to complete. The time required for
this analysis depends on the number of speakers connected.
The more connected speakers there are, the longer it takes to
perform analysis.
STEP 3
Calculate
Now calculating
Please wait
0%
screen, use ui to select “Next →
Audyssey Auto Setup MultEQ
[RETURN][ENTER] Enter Cancel
If you want to omit measurements from the next position onward,
select “Next Calculate”.
(Go to
STEP4 Calculate
)
Repeat step 10, measuring positions 3 to 6.
When measurement of position 6 is completed, a
11
“Measurements finished.” message is displayed.
Audyssey Auto Setup MultEQ
Measure (Finish)
Measurements finished.
Retry
Next Calculate
[RETURN][ENTER] Enter Cancel
16
Set up speakers (Audyssey® Auto Setup)
Basic version
Advanced version
Information
Basic version
STEP 5
Check
Use ui to select the item you
13
want to check, and then press
ENTER.
Audyssey Auto Setup
Check
Check processing resuit.
To proceed, press
“Next”.
Sp.Config. Check
Distance Check
Ch.Level Check
Crossover Check
Next Store
•Subwoofers may measure a greater reported distance than
the actual distance due to added electrical delay common in
subwoofers.
•If you want to check another item, press RETURN B.
Use ui to select “Next → Store” and then press
14
ENTER.
NOTE
•If the result differs from the actual connection status, or if “Caution!”
is displayed, see “Error messages” (vpage 18). Then carry out
Audyssey® Auto Setup again.
• If you change speaker positions or orientation, perform Audyssey®
Auto Setup again to find the optimal equalizer settings.
MultEQ
[RETURN][ENTER] Enter Cancel
STEP 6
Store
Select “Store” and then press ENTER.
15
Save the measurement results.
Audyssey Auto Setup MultEQ
Store
Press “Store” to
store calculation
result.
Store
[RETURN][ENTER] Enter Cancel
Audyssey Auto Setup MultEQ
Store
Now storing
Please wait...
0%
[RETURN][ENTER] Enter Cancel
•Saving the results requires about 10 seconds.
•If the measuring results are not to be saved, press RETURN B.
A message “Cancel Auto Setup?” will be displayed. Press o then
select “Yes”. All the measured Audyssey® Auto Setup data will
be erased.
•During saving of measurements results, “Now storing Please
wait...” is displayed. When saving is completed, “Storing complete.
Auto Setup is now finished.” is displayed.
NOTE
During saving of measurement results, be sure not to turn off the
power.
Finish
Unplug the setup microphone from the unit’s SETUP
16
MIC jack.
Set Audyssey Dynamic Volume®.
17
Audyssey Auto Setup MultEQ
Finish
Storing complete.
Auto Setup is now finished.
Please unplug microphone.
Turn on Dynamic Volume?
Yes
No
[ENTER] Exit
•This feature adjusts the output volume to the optimal level while
constantly monitoring the level of the audio input to the unit.
Optimal volume control is performed automatically without any
loss in the dynamism and clarity of the sound when, for example,
the volume suddenly increases for commercials shown during
television programs.
n When turning Dynamic Volume® on
•Use u to select “Yes”, and then press ENTER.
The unit automatically enters “Evening” mode.
n When turning Dynamic Volume® off
•Use i to select “No”, and then press ENTER.
NOTE
After performing Audyssey® Auto Setup, do not change the speaker
connections or subwoofer volume. In event of a change, perform
Audyssey® Auto Setup again.
17
Set up speakers (Audyssey® Auto Setup)
Basic version
Advanced version
Information
Basic version
Error messages
NOTE
•An error message is displayed if Audyssey® Auto Setup could not be completed due to speaker placement, the measurement environment, etc. If this happens, check the relevant items, be sure to take the necessary
measures, then perform Audyssey® Auto Setup over again.
•If the result still differs from the actual connection status after remeasurement or the error message still appears, it is possible that the speakers are not connected properly. Turn this unit off, check the speaker
connections and repeat the measurement process from the beginning.
•Be sure to turn off the power before checking speaker connections.
Examples Error details Measures
Audyssey Auto Setup
Caution!
Microphone or Speaker is none
Retry
MultEQ
•The connected setup microphone is broken, or a device other than the
supplied setup microphone is connected.
•Not all speakers could be detected.
•The front L speaker was not properly detected.
•Connect the included setup microphone to the SETUP MIC jack of this unit.
•Check the speaker connections.
Audyssey Auto Setup
Caution!
Ambient noise is too high or Level is too low
Retry
Audyssey Auto Setup
Caution! Speaker:None
Front R
Retry
Audyssey Auto Setup
Caution! Speaker:Phase
Front R
Skip
Retry
MultEQ
MultEQ
MultEQ
•There is too much noise in the room for accurate measurements to be
made.
•Speaker or subwoofer sound is too low for accurate measurements to be
made.
•The displayed speaker could not be detected.
(The screen on the left indicates that the front right speaker cannot be
detected.)
•The displayed speaker is connected with the polarity reversed.
(The screen on the left indicates that the polarity phases of the front right
speakers are reversed.)
•Either turn off any device generating noise or move it away.
•Perform again when the surroundings are quieter.
•Check the speaker installation and the direction in which the speakers are
facing.
•Adjust the subwoofer’s volume.
•Check the connections of the displayed speaker.
•Check the polarity of the displayed speaker.
•For some speakers, this error message may be
displayed even if the speaker is properly connected.
If you are sure the connection is correct, press ui
to select “Skip”, then press ENTER.
18
Set up speakers (Audyssey® Auto Setup)
Basic version
Advanced version
Information
Basic version
Parameter Check
This function enables you to check the measurement results and equalizer characteristics after Audyssey
Auto Setup.
Use ui to select “Parameter Check” and then press ENTER.
1
Auto Setup
Auto Setup
Parameter Check
Use ui to select the item you want to check, then press ENTER or p.
2
Measurement results for each speaker are displayed.
Sp.Config. Check
Distance Check
Ch. Level Check
Crossover Check
EQ Check
Check the speaker configuration.
Check the distance.
Check the channel level.
Check the crossover frequency.
Check the equalizer.
Sp. Config. Check
Distance Check
Ch. Level Check
Crossover Check
EQ Check
Making the network settings (Network Setup)
®
This unit can be connected to a home network (LAN) to listen to Internet radio or play back music files and
still image (JPEG) files stored on a computer.
Connect the Ethernet cable (vpage 12 “Connecting to a home network (LAN)”).
1
Turn on this unit (C page 5 “Getting Started”).
2
This unit performs automatic network setup due to the DHCP function.
When connecting to a network that has no DHCP function, perform the setting in “Network
Connect.” (vpage88).
•If “EQ Check” is selected, press ui to select equalizing curve (“Audyssey” or “Audyssey Flat”) to
be checked.
o p to switch the display between the different speakers.
Use
Press RETURN B.
3
The confirmation screen reappears. Repeat step 2.
Retrieving Audyssey® Auto Setup settings
If you set “Restore” to “Yes”, you can return to Audyssey® Auto Setup measurement result (value
calculated at the start by MultEQ®) even when you have changed each setting manually.
19
Playback (Basic operation)
Basic version
Advanced version
Information
Basic version
BD
Settings (vpage13)
n Selecting the input source (vpage20)
n Adjusting the master volume (vpage21)
n Turning off the sound temporarily (vpage21)
n Playing a Blu-ray Disc player/DVD player
(vpage21)
n Playing a CD player (vpage21)
n Playing an iPod (vpage22)
n Tuning in radio stations (vpage26)
n Playing a network audio (vpage28)
n Playing a USB memory device (vpage42)
Selecting a listening mode (Surround mode)
(vpage44)
Playback (Advanced operation) (vpage58)
Important information
Before starting playback, make the connections between the different
devices and the settings on the unit.
NOTE
Also refer to the operating instructions of the connected devices
when playing them.
Selecting the input source
Press the input source select button
(BD, SAT/CBL, TV, NET/USB, DVD,
V.AUX, DOCK, TUNER, GAME1,
GAME2, CD) to be played back.
The desired input source can be selected
directly.
You can also use the following operation to select an input
source.
nUsing the button on the main unit
Press the input source select button (TUNER, BD, SAT/CBL, TV,
GAME1/2, DVD, DOCK, CD, V.AUX, NET/USB) to be played back.
•When iPod 1 on the main unit is pressed, the input source of this
unit is switched to “DOCK” or “NET/USB” and the connected
iPod is automatically played (vpage25 “iPod play function”).
nUsing the “Source Select” menu
Switch the remote control unit to the J (MAIN ZONE) mode when
performing this operation (vpage101 “Operating AV devices”).
If the remote control unit is in K (ZONE2) mode, the “Source
Select” menu will not be displayed when SOURCE SELECT is
pressed.
Source Select
Player
BD
DVD
CD
DOCK
USB/iPod
Video
SAT/CBL
TV
GAME1
GAME2
V.AUX
q Press SOURCE SELECT.
Display the “Source Select” menu.
w Use uio p to select the input source,
then press ENTER.
The input source is set and the source
selection menu is turned off.
The currently selected input
source is highlighted.
Tuner
TUNER
[ENTER] Enter[ ] Move
Network
Favorites
Internet Radio
Media Server
Flickr
Pandora
Napster
Rhapsody
•When using with an iPod connected directly to the USB port of this
unit, select “USB/iPod” for the input source.
•Input sources that are not going to be used can be set ahead of time.
Make this setting at “Source Delete” (vpage92).
•To turn off the source selection menu without selecting an input
source, press SOURCE SELECT again.
•When SOURCE SELECT is pressed, the AMP-operation mode starts
automatically (vpage101).
20
Important information
Basic version
Advanced version
Information
Basic version
BD
Adjusting the master volume
Use M df to adjust the volume.
n When the “Volume Display” setting
(vpage92) is “Relative”
GAdjustable rangeH
– – –
–80.5dB – 18.0dB
n When the “Volume Display” setting (vpage92) is
“Absolute”
GAdjustable rangeH
•The variable range differs according to the input signal and channel
level setting.
You can also operate via the main unit. In this case, perform the
following operations.
Turn MASTER VOLUME to adjust the volume.
0.0 – 99.0
Turning off the sound temporarily
Press N.
•The power indicator flashes green.
•“MUTE” indicator on the display lights.
appears on a TV screen.
•
Playing a Blu-ray Disc player/DVD player
The following describes the procedure for playing Blu-ray Disc player/
DVD player.
Prepare for playback.
q Turn on the power of the TV,
1
2
3
4
subwoofer and player.
w Change the TV input to the input of
this unit.
e Load the disc in the player.
Press ON to turn on power to the
unit.
Press BD or DVD to switch an input source for a
player used for playback.
Play the device connected to this unit.
Make the necessary settings on the player (language setting,
subtitles setting, etc.) beforehand.
Playing a CD player
The following describes the procedure for playing CD player.
Prepare for playback.
q Turn on the power of the subwoofer
1
and player.
w Load the disc in the player.
Press ON to turn on power to the
2
unit.
Press CD to switch the input
3
source to the CD player.
Play the device connected to this unit.
4
•The sound is reduced to the level set at “Mute Level” (vpage92).
•To cancel, press N again. Muting can also be canceled by adjusting
the master volume.
21
Playing an iPod
Basic version
Advanced version
Information
Basic version
vSee overleaf
BD
There are two methods for iPod playback.
q Use a DENON control dock for iPod to play back.
You can play back both video, photo and audio.
w Connect an iPod directly to the USB port to play back
(vpage24).
You can play back audio only.
q
Use a DENON control dock for iPod to
play back
If you use a separately sold DENON control dock for iPod (ASD-1R or
ASD-11R), you will be able to play back videos, photos, music, and
other content on the iPod.
nListening to music on an iPod
Prepare for playback.
q Connect the DENON control dock
1
for iPod to this unit (vpage10
“Connecting a control dock for
iPod”).
w Set the iPod in the DENON control
dock for iPod.
Press ON to turn on power to the
2
unit.
Press DOCK to switch the input
3
source to “DOCK”.
•If ”Browse mode” is selected in step 4,
the following screen is displayed on a TV
screen, depending on the connected control
dock for iPod.
(When using an ASD-1R) (When using an ASD-11R)
Music
Playlists
Artists
Albums
Songs
Genres
Composers
[1/6]
iPod
Music
Videos
[1/2]
•In “Browse mode”, the iPod display is as
shown at right.
NOTE
If the connections screen is not displayed,
the iPod may not be properly connected.
Reconnect it.
OK to disconnect.
Press SEARCH and hold it down for 2 seconds or
4
more to select the display mode.
•There are two modes for displaying the contents recorded on the
iPod.
Browse mode
•English letters, numbers and certain symbols are displayed.
Incompatible characters are displayed as “.” (period).
Remote mode
•“Remote iPod” is displayed on the display of this unit.
Display mode
Playable
files
Active
buttons
z1 When using an ASD-11R DENON control dock for iPod.
z2 Video may not be output, depending on the combination of
ASD-1R or ASD-11R DENON control dock for iPod and iPod.
Display iPod information on the TV screen.
Display iPod information on the iPod screen.
Browse mode Remote mode
Music file
Photo file
Video file
Remote
control unit
(This unit)
iPod
P P
z1
P
P P
P
P
P
z2
z2
Use ui to select the item, then press ENTER or p
5
to select the le to be played.
Press ENTER, p or 1.
6
Playback starts.
•You can specify the duration of the on-screen display to be displayed
(default: 30 sec) at menu “iPod” (vpage93). Press uio p to
return to the original screen.
•To play back compressed audio with extended bass or treble
reproduction, we recommend playback in RESTORER mode
(vpage80). The default setting is “Mode3”.
•In Browse mode, press STATUS on the main unit during playback
to check the title name, artist name, and album name on the display
of this unit.
NOTE
•Press STANDBY and set this unit’s power to
the standby mode before disconnecting the
iPod. You can also switch the input source
to other than “DOCK” and then disconnect
the iPod.
•Depending on the type of iPod and the software version, some
functions may not operate.
•Note that DENON will accept no responsibility whatsoever for any
problems arising with the data on an iPod when using this unit in
conjunction with the iPod.
22
nViewing videos on an iPod in the Browse mode
Basic version
Advanced version
Information
Basic version
BD
When an iPod equipped with a video function is connected to a
DENON ASD-11R control dock for iPod, image files can be played
in the Browse mode.
Use ui to select “Videos”, then
1
press ENTER or p.
Use ui to select the search item
2
or folder, then press ENTER or
p.
Use ui to select the video le,
3
then press ENTER, p or 1.
Playback starts.
nViewing photos and videos on an iPod in the
Remote mode
This unit can play back on a TV screen photos and data stored on an
iPod equipped with a slide show or video function.
Press and hold SEARCH to set the
1
Remote mode.
“Remote iPod” is displayed on the
display of this unit.
Watching the iPod’s screen,
2
use ui to select “Photos” or
“Videos”.
•Depending on the iPod model, it may be necessary to operate the
iPod unit directly.
Press ENTER until the image you want to view is
3
displayed.
“TV Out” at the iPod’s “Slide show Settings” or “Video Settings”
must be set to “On” in order to display the iPod’s photo data or videos
on the monitor. For details, see the iPod’s operating instructions.
NOTE
Video may not be output, depending on the combination of ASD-1R or
ASD-11R and iPod.
niPod operation
Operation buttons Function
MENU Amp menu
uio p
ENTER
(Press and release)
ENTER
(Press and hold)
SEARCH
(Press and release)
SEARCH
(Press and hold)
RETURN B
6 7
(Press and hold)
1
8 9
3
2
TV Z / X
TV INPUT Switch TV input (Default : SONY)
•Repeat playback (vpage99 “Repeat”)
•Shuffling playback (vpage99 “Shuffle”)
z When the menu screen is displayed, press
(previous page) or p (next page).
To cancel, press ui or SEARCH.
Auto search (cue, ui) /
Manual search (Press and hold, ui)
Page search mode
Browse / Remote mode switching
(fast-reverse/fast-forward)
TV power on/standby (Default : SONY)
Playing an iPod
Cursor operation /
Enter / Pause
Stop
z
Return
Manual search
Playback / Pause
Auto search (cue)
Pause
Stop
SEARCH, then press o
23
w
Basic version
Advanced version
Information
Basic version
vSee overleaf
BD
Connect an iPod directly to the USB port
to play back
You can use the USB cable provided with the iPod to connect the iPod
with the unit’s USB port and enjoy music stored on the iPod.
•This unit supports audio playback from the iPod (fifth generation
or later), iPod nano, iPod classic, iPod touch and iPhone (it is not
compatible with iPod shuffle).
Connect the iPod to the USB port (vpage 10
“Connecting an iPod or USB memory device to the
1
USB port”).
Press ON to turn on power to the unit.
2
Press NET/USB to switch the input source to “NET/
3
USB”.
DENON:[AVR-1912]
Favorites
Internet Radio
Media Server
iPod
Flickr
Napster
Pandora
CH +/-
Preset
Use ui to select “iPod”, then
4
press ENTER or p.
iPod
Playlists
Artists
Albums
Songs
Podcasts
Genres
Composers
[1/8]
[1/8]
Press SEARCH and hold it down for 2 seconds or
5
more to select the display mode.
•There are two modes for displaying the contents recorded on the
iPod.
Browse mode
•English letters, numbers and certain symbols are displayed.
Incompatible characters are displayed as “.” (period).
Remote mode
•“Remote iPod” is displayed on the display of this unit.
•The Remote mode is not supported on fifth generation iPod or
first generation iPod nano.
Display mode
Playable
files
Active
buttons
z Only the sound is played.
Display iPod information on the TV screen.
Display iPod information on the iPod screen.
Browse mode Remote mode
Music file
Video file
Remote
control unit
(This unit)
iPod
P P
P P
z
P
Use ui to select the item, then press ENTER or p
6
to select the le to be played.
Press ENTER, p or 1.
7
Playback starts.
Playing an iPod
•You can specify the duration of the on-screen display to be displayed
(default: 30 sec) at menu “iPod” (vpage 93). Press uio p
to return to the original screen.
•To play back compressed audio with extended bass or treble
reproduction, we recommend playback in RESTORER mode
(vpage80). The default setting is “Mode3”.
•In Browse mode, press STATUS on the main unit during playback to
check the title name, artist name, and album name.
NOTE
•Depending on the type of iPod and the software version, some
functions may not operate.
•Note that DENON will accept no responsibility whatsoever for any
problems arising with the data on an iPod when using this unit in
conjunction with the iPod.
NOTE
If the “iPod” is not displayed, the iPod may not be properly
connected. Reconnect it.
SEARCH
P/Search
24
niPod operation
Basic version
Advanced version
Information
Basic version
BD
Operation buttons Function
MENU Amp menu
Cursor operation /
uio p
ENTER
(Press and release)
ENTER
(Press and hold)
SEARCH
(Press and release)
SEARCH
(Press and hold)
RETURN B
6 7
(Press and hold)
1
8 9
3
2
TV Z / X
TV INPUT Switch TV input (Default : SONY)
•Repeat playback (vpage99 “Repeat”)
•Random playback (vpage99 “Shuffle”)
1
z
When the menu screen is displayed, press SEARCH, then press
o (previous page) or p (next page).
To cancel, press ui or SEARCH twice.
z2 When the menu screen is displayed, press SEARCH twice, then
press o p to select the first letter you want to search mode.
•If it is not possible to search the list, “unsorted list.” is displayed.
To cancel, press ui or SEARCH.
Auto search (cue, ui) /
Manual search (Press and hold, ui)
Enter / Pause
Stop
z1
Page search
Browse / Remote mode switching
(fast-reverse/fast-forward)
TV power on/standby (Default : SONY)
/ Character sort
Return
Manual search
Playback / Pause
Auto search (cue)
Pause
Stop
z2
Playing an iPod
iPod play function
If iPod 1 is pressed when a control dock for iPod or an iPod (USB) is
connected, the iPod starts playback.
Press iPod 1.
•This unit’s input source switches to
“DOCK” or “NET/USB”.
•iPod playback starts.
NOTE
If both a control dock for iPod (“DOCK”) and an iPod (“NET/USB”)
are connected, playback with control dock for iPod (“DOCK”) takes
priority.
If the list is not in alphabetical order, you may not be able to perform
a character sort.
25
Tuning in radio stations
Basic version
Advanced version
Information
Basic version
vSee overleaf
BD
Listening to FM/AM broadcasts
Press TUNER to switch the input
1
source to “TUNER”.
Press BAND to select “FM” or
2
“AM”.
FM
When listening to an FM broadcast.
AM
When listening to an AM broadcast.
TUNER
AUTO
[
CH+/-
FM 87.50MHz
Tuning[ / ]
] Preset
[
]
MEMORY
[
]
Band
Memory
Now Playing
A1
] Mode
[
[
SEARCH
] Search
Tune in the desired broadcast station.
3
q To tune in automatically (Auto tuning)
Press MODE to light the “AUTO” indicator on the display, then
use TUNING d or TUNING f to select the station you want to
hear.
w To tune in manually (Manual tuning)
Press MODE to turn off the display’s “AUTO” indicator, then use
TUNING d or TUNING f to select the station you want to hear.
nPresetting radio stations (Manual preset)
Your favorite broadcast stations can be preset so that you can tune
them in easily. Up to 56 stations can be preset.
•Stations can be preset automatically at “Auto Preset”
(vpage96). If “Auto Preset” is performed after performing
“Manual preset”, the “Manual preset” settings will be overwritten.
Tune in the broadcast station you want to preset.
1
TUNER
AUTO
[
CH+/-
FM 87.50MHz
Tuning[ / ]
] Preset
[
MEMORY
[
]
]
Band
Memory
Now Playing
A1
[
[
SEARCH
] Mode
] Search
Press MEMORY.
2
TUNER
To store preset:
A1-G8
Select
[
MEMORY
[
CH+/-
SHIFT
Tuning[ / ]
] Preset
]
1-8
][
[
MEMORY
]
Band
]
Memory
][
A1
] Mode[
[
Default settings
Block (A – G)
and
Default Settings
Channel (1 – 8)
A1 – A8
B1 – B8
87.50 / 89.10 / 98.10 / 107.90 / 90.10 / 90.10 /
90.10 / 90.10 MHz
520 / 600 / 1000 / 1400 / 1500 / 1710 kHz,
90.10 / 90.10 MHz
C1 – C8 90.10 MHz
D1 – D8 90.10 MHz
E1 – E8 90.10 MHz
F1 – F8 90.10 MHz
G1 – G8 90.10 MHz
Specify a name for the preset broadcast station
(Preset Name) (vpage96)
•If the desired station cannot be tuned in with auto tuning, tune it in
manually.
•When tuning in stations manually, press and hold TUNING d or
TUNING f to change frequencies continuously.
•The time (default : 30 sec) for which the menu are displayed can be
set at menu “Tuner” (vpage 93). Press uio p to return to
the original screen.
Press SHIFT to select the block (A to G) in which the
3
channel (1 to 8 per a block) is to be preset, then press
CH +, CH – or 1 – 8 to select the preset number.
Press MEMORY again to complete the setting.
4
•To preset other stations, repeat steps 1 to 4.
26
nListening to preset stations
Basic version
Advanced version
Information
Basic version
BD
Press SHIFT to select the memory
1
block (A to G).
TUNER
[
[
SEARCH
] Mode[
] Search
AUTO
Preset Channel
A8 FM 90.10MHz
A7 FM 90.10MHz
A6 FM 90.10MHz
A5 FM 90.10MHz
A4 FM 107.90MHz
A3 FM 98.10MHz
A2 FM 89.10MHz
A1 FM 87.50MHz
[
CH+/-
Tuning[ / ]
] Preset
[
MEMORY
]
]
Band
Memory
Press CH +, CH – or 1 – 8 to select the desired preset
2
channel.
You can also operate via the main unit. In this case, perform the
following operations.
Press TUNER PRESET CH + or TUNER PRESET CH – to select a preset
radio station.
nDirect frequency tuning
You can enter the receiving frequency directly to tune in.
Press SEARCH.
1
TUNER
AUTO
[
CH+/-
FM ---.- MHz
DIRECT TUNE
Tuning[ / ]
] Preset
[
MEMORY
]
]
Band
Memory
Now Playing
B6
[
[
SEARCH
] Mode[
] Search
Input frequencies using the 0 – 9.
2
•If o is pressed, the immediately preceding input is cancelled.
When setting is completed, press ENTER.
3
The preset frequency is tuned in.
nTuner (FM/AM) operation
Operation buttons Function
CH +, – Preset channel selection
MENU Amp menu
uio p
ENTER Enter
SEARCH Direct frequency tuning
RETURN B
BAND FM/AM switching
MODE Switch search modes
TUNING df
0 – 9
SHIFT Preset channel block selection
MEMORY Preset memory registration
TV Z / X
TV INPUT Switch TV input (Default : SONY)
Tuning in radio stations
Cursor operation
Return
Tuning (up/down)
Preset channel selection (1 – 8) /
Direct frequency tuning (0 – 9)
TV power on/standby (Default : SONY)
27
Loading...