Dell S560T, S560P User Manual

Download

Dell Interactive Projector

S560P/ S560T

User’s Guide

Notes, Cautions, and Warnings

NOTE: A NOTE indicates important information that helps you make

better use of your projector

CAUTION: A CAUTION indicates potential damage to hardware or

loss of data if instructions are not followed.

WARNING: A WARNING indicates a potential for property damage,

personal injury, or death.

____________________

Reproduction of these materials in any manner whatsoever without the written permission of Dell Inc. is strictly forbidden.

Trademarks used in this text: Dell and the DELL logo are trademarks of Dell Inc.; DLP and DLP logo are trademarks of T Windows are either trademarks or registered trademarks of Microsoft Corporation in the United States and/or other countries.

Other trademarks and trade names may be used in this document to refer to either the entities claiming the marks and names or their products. Dell Inc. disclaims any proprietary interest in trademarks and trade names other than its own.

Model: Dell Projector S560P/S560T

June 2016 Rev. A00

EXAS INSTRUMENTS INCORPORATED; Microsoft and

Contents

1 About Your Dell Projector . . . . . . . . . . . . . . . . . 5

Projector Box Contents . . . . . . . . . . . . . . . . . . . . 5

Projector Top and Bottom View Projector Connections Adjusting Image Size Remote Control

. . . . . . . . . . . . . . . . . . . . . 8

. . . . . . . . . . . . . . . . . . . . . 10

. . . . . . . . . . . . . . . . . . . . . . . . 12

2 Using Interactive Pen (Only for S560P) . . . . . 16

System Requirements. . . . . . . . . . . . . . . . . . . . . 16

About Your Interactive Pen Replacing the Interactive Pen Tips Replacing the Interactive Pen Batteries Using Interactive Pen with S560P Touc h Ar ea S e tt i ng Pen Calibration

. . . . . . . . . . . . . . . . . . . . . . . 21

. . . . . . . . . . . . . . . . . . . . . . . . . 23

3 Using Interactive Touch (Only for S560T) . . . 24

System Requirements. . . . . . . . . . . . . . . . . . . . . 24

Setting Up Interactive Touch Using Interactive Touch with S560T Touc h Ar ea S e tt i ng Interactive Touch Calibration Using S560T and Dry Erase Whiteboard

. . . . . . . . . . . . . . . . . . . . . . . 27

. . . . . . . . . . . . . . . 7

. . . . . . . . . . . . . . . . . 17

. . . . . . . . . . . . 18

. . . . . . . . . 19

. . . . . . . . . . . . . 20

. . . . . . . . . . . . . . . . 25

. . . . . . . . . . . 25

. . . . . . . . . . . . . . . . 29

. . . . . . . . . 30

4 Connecting Wireless Display Adapter . . . . . . 31

Installing Wireless Display Adapter . . . . . . . . . . . . 31

Setting up the Wireless Display Adapter

. . . . . . . . . 32

5 Troubleshooting. . . . . . . . . . . . . . . . . . . . . . . . 33

Troubleshooting Tips . . . . . . . . . . . . . . . . . . . . . 33

Guiding Signals

. . . . . . . . . . . . . . . . . . . . . . . . . 37

6 Maintenance. . . . . . . . . . . . . . . . . . . . . . . . . . . 38

Changing the Lamp . . . . . . . . . . . . . . . . . . . . . . 38

Replacing Remote Control Batteries

. . . . . . . . . . . 40

Contents | 3

7 Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . 41

8 Additional Information . . . . . . . . . . . . . . . . . . 45

9 Contacting Dell . . . . . . . . . . . . . . . . . . . . . . . . 46

4 | Contents

About Your Dell Projector

Calibrate Touch

VGA

Freeze

Blank Screen

Video Mode

Info

HDMI

AAA

Your projector comes with all the items shown below. Ensure that you have all the items, and contact Dell if anything is missing.

Projector Box Contents

Package Contents

Power cable 5 m VGA cable (VGA to VGA)

Remote control AAA Batteries (2 for S560T; 6 for

S560P)

CD, User’s Guide, and Documentation

Informacion Importante

Dell™ Projector S560P/T

Document

tion

™

Projector S560P/T

018TWNA00

C o

n te

n t

s :

• Us e

r 's

G uide

l l

P/N 18TWN

v. A00

P/N 36.76G04G001

June 2016

Made

C h

i na

5 m Mini cable (USB-A to Mini B)

About Your Dell Projector 5

Package Contents (S560P only)

Interactive pen (2 pcs)/ Pen tip cap (4 pcs)

Package Contents (S560T only)

Touch Unit 2 m DC to DC power cable (for

Passive Pen (2 pcs)/ Pen Nib(2 pcs) Touch unit Base Plate kit

Wrist strap (2pcs)

Touc h u nit )

6 About Your Dell Projector

Projector Top and Bottom View

3 5

Top View Bottom View

1 Infrared (IR) receivers

2 Power button

3 Camera

4 Lens

5 Lamp cover

6 Mounting holes for wall mount

A : Dell S560 wall mount B : Universal wall mount

NOTE: Wall mount screw hole M4 X 4. Recommended torque < 15

kgf-cm.

About Your Dell Projector 7

Projector Connections

1 2 3 4 5 6 7 8 910

12131415

1 Mini USB (Mini Type B) 9 Microphone connector 2 VGA Out connector (monitor

loop through) 3 VGA In connector 11 Power cord connector 4 Composite Video connector 12 USB A connector 5 HDMI 2 connector 13 RJ 45 connector 6 HDMI 1 connector 14 RS232 connector 7 Audio Input connector 15 Touch Unit power 8 Audio RCA connector

CAUTION: Before you begin any of the procedures in this section,

follow the Safety Instructions as described on page 9.

10 Audio Output connector

8 About Your Dell Projector

CAUTION: Safety Instructions

Do not use the projector near appliances that generate a lot of heat.

Do not use the projector in areas where there is an excessive amount of dust. The dust may cause the system to fail and the projector will automatically shutdown.

Ensure that the projector is mounted in a well-ventilated area.

Do not block the ventilation slots and openings on the projector.

Ensure the projector operates between ambient temperatures (5 °C to 40 °C).

Do not try to touch the ventilation outlet as it can become very hot after the projector has been turned on or immediately after it is turned off.

Do not look into the lens while the projector is on as it may cause injury to your eyes.

Do not place any objects near or in front of the projector or cover its lens while the projector is on as the heat may cause the object to melt or burn.

Do not use alcohol to wipe the lens.

NOTE:

•

Do not attempt to wall mount the projector by yourself. It should be installed by a qualified technician.

•

Recommended Projector Wall Mount Kit. For more information, see the Dell Support website at

•

For more information, see the Safety Information that shipped with

dell.com/support

your projector.

•

The S560P/ S560T projector can only be used indoors.

About Your Dell Projector 9

Adjusting Image Size

0.66' (20cm)

0.73' (22.2 cm)

0.82' (25cm)

0.805' (24.5 cm)

0.913' (27.7 cm)

1.004' (30.6cm)

81" (205.7 cm)

85" (215.9 cm)

90" (228.6 cm)

95" (241.3cm)

89.1" (226.3 cm)

100" (254 cm)

Projector to screen distance

10 About Your Dell Projector

Adjusting Image Shape

Screen Size

Diagonal Width Height wide wide

inch mm inch mm inch mm inch mm inch mm inch mm inch mm

81 2057 71 1793 40 1009 6 145 45 1153 8 200 18 452

85 2159 74 1882 42 1059 6 154 48 1212 9 222 19 474

89.1 2263 78 1972 44 1110 6 163 50 1273 10 245 20 497

90 2286 78 1992 44 1121 7 165 51 1286 10 250 20 502

95 2413 83 2103 47 1183 7 177 54 1360 11 278 21 530

100 2540 87 2214 49 1245 7 188 56 1434 12 306 22 558

H1 H2

L1 L2

About Your Dell Projector 11

Remote Control

316

19 20

21 22

23 24

Calibrate

Touc h

Freeze

Blank

Info

Screen

Video

HDMI

VGA

Mode

7 8 9 10

11 12

1 Power Turns the projector on or off.

2 Up Press to navigate through the On-Screen

Display (OSD) Menu items.

3 Right Press to navigate through the On-Screen

Display (OSD) Menu items.

4 Down Press to navigate through the On-Screen

Display (OSD) Menu items.

12 About Your Dell Projector

5 Laser Point the remote control at the screen, press

and hold the laser button to activate the laser light.

WARNING: Do not look at the laser

point when it is active. Avoid directing the laser light on your eyes.

6 Freeze Press to pause the screen image, then press

"Freeze" again to unfreeze the image.

7 Brightness + Press to increase the brightness.

8 Keystone adjustment + Press to adjust image distortion caused by

tilting the projector (+/-40 degrees).

9 Brightness - Press to decrease the brightness.

10 Keystone adjustment -Press to adjust image distortion caused by

tilting the projector (+/-40 degrees).

11 Blank screen Press to toggle among displaying blank white

and black screens and return to presentation.

12 Info Press to display the projector information.

13 Video mode The projector has preset configurations that

are optimized for displaying data (presentation slides) or video (movies, games, etc.).

Press the Video Mode button to toggle between Presentation mode, Bright mode, Movie mode, sRGB, or Custom mode.

Pressing the Video Mode button once will show the current display mode. Pressing the Video Mode button again will switch between modes.

14 HDMI Press to choose HDMI source.

15 Enter Press to confirm the selection.

16 Left Press to navigate through the On-Screen

Display (OSD) Menu items.

17 Menu Press to activate the OSD.

18 Source Press to switch between VGA, Composite,

HDMI-1, and HDMI-2 source.

About Your Dell Projector 13

19 Volume up Press to increase the volume.

20 Zoom + Press to increase the image.

21 Volume down Press to decrease the volume.

22 Zoom - Press to decrease the image.

23 Mute Press to mute or un-mute the projector

speaker.

24 Auto Adjust Press to auto adjust the displayed image.

25 Calibrate Touch Press to calibrate touch to adjust for better

accuracy.

NOTE: Setup Utility is required.

26 VGA Press to choose VGA source.

14 About Your Dell Projector

Remote Control Operating Range

Angle

Distance

Angle

Distance

Calibrate Touch

VGA

Freeze

Blank Screen

Video Mode

Info

HDMI

Calibrate

Touch

VGA

Freeze

Blank

Screen

Video

Mode

Info

HDMI

Operating range

Angle

±30°

Distance

7 m/22.97 feet

NOTE: Actual operating range may slightly differ from the diagram.

Weak batteries will also prevent the remote control from properly operating the projector.

About Your Dell Projector 15

Using Interactive Pen (Only

The S560P projector projects the connected computer’s desktop image onto the whiteboard and it acts as input device to the computer. You can navigate, select, and interact with your computer programs from the whiteboard.

The S560P is a pen-based interactive projector. Download and install Dell S560x Interactive Utility for first-time setup and interactivity calibration.

for S560P)

System Requirements

NOTE: Your computer must have the following minimum system

requirements:

Operating System

Windows 7/8/10

MAC OS X (10.7~10.11)

ChromeBook 10 touch points Not supported,

Number of touch points supported

10 touch points Supported

1 touch point

Installation of S560x Interactive Utility

For first-time setup For subsequent use

Supported Required, please

please use a Windows OS or Mac OS computer to complete first-time setup for the S560P

Not required

install the setup utility on all Mac OS computers, to use them with the S560P

Not required

*1 : Get S560x Interactive Utility from provided CD or download it from Dell Support

*2 : S560P requires first-time calibration, ensure you calibrate the interactive pen(s) before use

*3 : .NET Framework 4.0 installation is required *4 : Mac OS support 1 touch point only

16 Using Interactive Pen (Only for S560P)

NOTE: For better accuracy, you should set to "Projector Only"

display mode before calibration. More details about touch function and calibration in different display modes, please go to "S560T Touch setup Guide" Troubleshooting Q2.

About Your Interactive Pen

The interactive pen allows user to interact with projected content in the same fashion as a mouse input.

2 1

1 Power switch

2 Power indicator

As you turn on the pen, the power indicator flashes a few seconds and goes off.

Green: Normal operation

Red: Battery is low

No light: Battery is empty

3 Wrist strap holder

4 Battery compartment access. Turn to open and replace batteries.

5 Pen tip

Using Interactive Pen (Only for S560P) 17

Replacing the Interactive Pen Tips

NOTE: If the pen tip becomes damaged, or no longer works well,

you should replace them.

18 Using Interactive Pen (Only for S560P)

Replacing the Interactive Pen Batteries

NOTE: If the battery is low, the LED indicator starts flashing red as

you turn on the pen. You should replace with two new AAA batteries.

You can access the battery compartment by turning open the pen head.

Insert the batteries and align their polarity correctly according to the marking on the pen head.

NOTE: Avoid mixing different types of batteries or using new and

old batteries together.

Place the pen head back, turn until the battery compartment access is fully closed.

Using Interactive Pen (Only for S560P) 19

Using Interactive Pen with S560P

MOLEX

Step 1: Connect the computer with the projector using HDMI/ VGA cable to display image. Connect the USB cable for using in interactive mode. If using Mac OS, run the S560x Interactive utility to setup the pen.

Step 2. Run Dell S560x Interactive Utility, users can select default Interactive Mode ( ) for multi-point touch. Switch to Active Pen Mode for S560P.

Only single-point touch supported for Mac OSX

NOTE: For Mac OS computer, Dell S560x Interactive Utility must be

executed.

20 Using Interactive Pen (Only for S560P)

Touch Area Setting

Switch to display mode "Projector only".

Select Auto Touch Area Setting:

NOTE:

•

Quit all software applications

•

Reduce ambient light

•

Do not obstruct or shake lens during Touch Area Setting

•

Check if projection image is clear. If not, adjust focus to sharpen the image

•

If fail message pops up, switch to Manual Touch Area Setting.

Select Manual Touch Area Setting:

Using Interactive Pen (Only for S560P) 21

2-1 After the camera captures the projection image, a Touch Area

window will pop up. If the captured image is not clear enough, please re-select "Ambient light mode selection" from "Auto" to "Bright" or "Dim" according to actual ambient light condition.

Remark: Captured image shows the actual camera view, which is reversed from projection image. For example: P1 is lower right corner, P2 is lower left corner and so on.

2-2 Touch Area Boundary Fine-tuning

Step 1: Click on P1, use mouse to drag P1 to upper left corner. Align

adjustable green zone with projected white frame.

Step 2: Adjust P2 to P4 accordingly; adjustable green zone should

completely overlaps the projected white frame.

Step 3: Finally, check again if the green frame completely overlaps the

projected white frame. If not, fineadjust again.

2-3 When the Touch Area is correctly located then click exit button.

22 Using Interactive Pen (Only for S560P)

Pen Calibration

Switch to display mode "Projector only".

Perform touch calibration on S560P using the S560x interactive utility (Win, Mac).

Select auto-calibration while running the S560X interactive utility.

NOTE: If the fail message pops up, follow below steps to trouble-

shoot and do Auto Calibration again.

•

Close all software applications

•

Reduce ambient light

•

Do not obstruct or shake lens during calibration

•

Check if projected image is clear, if not, adjust focus to sharpen the image

If auto-calibration fails, setup using 'manual calibration'.

Select Manual Calibration, and follow the steps for calibration. Manual Calibration is suggested to get a better accuracy.

Using Interactive Pen (Only for S560P) 23

Using Interactive Touch (Only

The S560T projector projects the connected computer's desktop image onto the whiteboard and it acts as input device to the computer. You can navigate, select, and interact with your computer programs from the whiteboard.

The S560T projector is a 10-pt multi-touch interactive projector. To setup the interactive function, install the touch unit as described in the 'Touch setup guide'. Also, use the Dell S560x Interactive utility for first-time setup and calibration which can be found in CD & download from Dell Support.

for S560T)

System Requirements

NOTE: You computer must have the following minimum system

requirements::

Operating System

Windows 7/8/10

MAC OS X (10.7~10.11)

ChromeBook 10 touch points Not supported,

Number of touch points supported

10 touch points Supported

1 touch point

Installation of S560x Interactive Utility

For first-time setup For subsequent use

Supported

please use a Windows OS or Mac OS computer to complete first-time setup for the S560T

Not required

Required, please install the setup utility on all Mac OS computers, to use them with the S560T

Not required

*1 : Get S560x Interactive Utility from provided CD or download it from Dell Support

*2 : S560T requires first-time alignment and calibration, ensure you complete setup process before use

*3 : NET Framework 4.0 installation is required

24 Using Interactive Touch (Only for S560T)

*4 : Mac OS support 1 touch point only

NOTE: For better accuracy, you should set to "Projector Only"

display mode before calibration. More details about touch function and calibration in different display modes, please go to "S560T Touch setup Guide" Troubleshooting Q2.

Setting Up Interactive Touch

To setup the interactive function, install the touch unit as described in the 'Touch setup guide'.

Using Interactive Touch with S560T

MOLEX

Using Interactive Touch (Only for S560T) 25

Step 2: Running Dell S560x Interactive Utility, users can select default Interactive

Mode ( ) for multi-point touch. Switch to Finger/Stylus Mode for S560T with Touch Unit interactive touch.

Only single-point touch is available for Mac OS X system.

NOTE: For Mac OS computer, Dell S560x Interactive Utility must be

executed.

26 Using Interactive Touch (Only for S560T)

Touch Area Setting

Switch to display mode "Projector only".

Select Auto Touch Area Setting:

NOTE:

•

Quit all software applications

•

Reduce ambient light

•

Do not obstruct or shake lens during Touch Area Setting

•

Check if projection image is clear. If not, adjust focus to sharpen the image

•

If fail message pops up, switch to Manual Touch Area Setting.

Select Manual Touch Area Setting:

Using Interactive Touch (Only for S560T) 27

2-1 After the camera captures the projection image, a Touch Area

window will pop up. If the captured image is not clear enough, please re-select "Ambient light mode selection" from "Auto" to "Bright" or "Dim" according to actual ambient light condition.

Remark: Captured image shows the actual camera view, which is reversed from projection image. For example: P1 is lower right corner, P2 is lower left corner and so on.

2-2 Touch Area Boundary Fine-tuning

Step 1: Click on P1, use mouse to drag P1 to upper left corner. Align

adjustable green zone with projected white frame.

Step 2: Adjust P2 to P4 accordingly; adjustable green zone should

completely overlaps the projected white frame.

Step 3: Finally, check again if the green frame completely overlaps the

projected white frame. If not, fineadjust again.

2-3 When the Touch Area is correctly located then click exit button.

28 Using Interactive Touch (Only for S560T)

Interactive Touch Calibration

Switch to display mode "Projector only".

Perform touch calibration on S560P using the S560x interactive utility (Win, Mac).

Select auto-calibration while running the S560X interactive utility.

NOTE: If the fail message pops up, follow below steps to trouble-

shoot and do Auto Calibration again.

•

Close all software application

•

Reduce ambient light

•

Do not obstruct or shake lens during calibration

•

Check if projection image is clear, if not, adjust focus to sharpen the image

If auto-calibration fails, setup using 'manual calibration'.

Select Manual Calibration, and follow the steps for calibration. Manual Calibration is suggested to get a better accuracy.

Using Interactive Touch (Only for S560T) 29

Using S560T and Dry Erase Whiteboard

Calibrate

Touch

VGA

Freeze

Blank Screen

Video

Mode

Info

HDMI

Freeze

To use the dry-erase marker on whiteboard without affecting the touch operation, use the 'freeze' key or the 'blank screen' key on the remote.

Freeze: Use the freeze key to pause the image on the screen and suspend touch functionality Press the freeze key again to resume touch operation.

Blank screen: Use Blank screen key to display a blank screen on the projector. Press the key to toggle between white background/ black background and to resume normal operation. During 'blank screen' mode, touch operation is suspended.

Freeze

Blank

Screen

Blank

Info

Calibrate

30 Using Interactive Touch (Only for S560T)

Touch

Screen

Video

HDMI

VGA

Mode

Connecting Wireless Display

Installing Wireless Display Adapter

Your projector has HDMI and USB power port for wireless display adapter. The wireless display adapter is not shipped with your S560P/S560T.

The installation steps are as below:

Make sure projector is already powered off.

Attach the power USB cable to the wireless display adapter and then attach the wireless display adapter.

Adapter

NOTE: The power USB cable is shipped with wireless display

adapter and not shipped with your projector.

Connecting Wireless Display Adapter 31

Setting up the Wireless Display Adapter

Power on the projector.

Switch to "Wireless Display" source.

Refer to your Wireless Display Adapter setup instructions to proceed with wireless projection.

32 Connecting Wireless Display Adapter

Troubleshooting

CRT/LCD

Troubleshooting Tips

If you experience problems with your projector, see the following troubleshooting tips. If the problem persists, contact Dell: www.dell.com/contactDell.

Problem Possible Solution

•

No image appears on the screen

Ensure that you have chosen the correct input source on the INPUT SOURCE menu.

•

Ensure the external graphics port is enabled. If you are using a Dell laptop computer, press (Fn+F8). For other computers, see your respective documentation. If images are not displayed properly, please upgrade the video driver of your computer. For Dell computers, see www.dell.com/support.

•

Ensure that all the cables are securely connected. See "Adjusting Image Size" on page 10.

•

Ensure that the pins of the connectors are not bent or broken.

•

Ensure that the lamp is securely installed (see "Changing the Lamp" on page 38).

•

Use the Test Pattern in the Projector Settings of the Advanced Settings menu. Ensure that the colors of the test pattern are correct.

Troubleshooting 33

Problem (continued) Possible Solution (continued)

Partial, scrolling, or incorrectly displayed image

Press the Auto Adjust button on the remote control.

If you are using a Dell laptop computer, set the resolution of the computer to 1080p (1920 x 1080):

Right-click the unused portion of your Microsoft

Properties

Windows® desktop, click , and then select

tab.

Verify that the setting is 1920 x 1080 pixels for the external monitor port.

Press (Fn+F8).

If you experience difficulty in changing resolutions, or if your monitor freezes, restart all the equipment and the projector.

If you are not using a Dell laptop computer, see your documentation. If images are not displayed properly, please upgrade the video driver of your computer. For a Dell computer, see www.dell.com/support.

The screen does not display your presentation

Image is unstable or flickering

If you are using a portable computer, press (Fn+F8).

Adjust the tracking in the OSD Display Settings of the Advanced Settings menu (in PC Mode only).

Image has vertical flickering bar

Adjust the frequency in the OSD Display Settings of the Advanced Settings menu (in PC Mode only).

Settings

34 Troubleshooting

Problem (continued) Possible Solution (continued)

Image color is incorrect

Image is out of focus 1

The image is stretched when displaying a 16:9 DVD

Image is reversed Select Projector Settings of the

Lamp is burned out or makes a popping sound

LAMP light is solid amber If the LAMP light is solid amber, replace

•

If the display receives the wrong signal output from the graphics card, please set

RGB

the signal type to

Settings

•

Use

Settings

menu. Ensure that the colors of the test pattern are correct.

Ensure that the projection screen is within the required distance from the projector (1.46 ft [44.6cm] ~1.83ft [55.8]).

The projector automatically detects the input signal format. It will maintain the aspect ratio of the projected image according to the input signal format with an Original setting.

If the image is still stretched, adjust the aspect ratio in the Display Settings of the Advanced Settings menu in the OSD.

Advanced Settings from the OSD and adjust the projector mode.

When the lamp reaches its end of life, it may burn out and may make a loud popping sound. If this occurs, the projector does not turn back on. To replace the lamp, see "Changing the Lamp" on page 38.

the lamp.

of the

Test Pattern

of the

in the OSD

Advanced Settings

in the

Projector

Advanced Settings

Image

tab.

Troubleshooting 35

Problem (continued) Possible Solution (continued)

LAMP light is blinking amber

TEMP light is solid amber The projector has overheated. The display

TEMP light is blinking amber

The remote control is not operating smoothly or works only within a limited range

If the LAMP light is blinking amber, the lamp module connection may be disrupted. Please check the lamp module and ensure that it is properly installed.

If the LAMP lights and the Power light is blinking amber, the lamp driver has failed and the projector will automatically shut down.

If the LAMP and TEMP lights are blinking amber and the Power light is solid blue, the color wheel has failed and the projector will automatically shut down.

To clear the protection mode, press and hold the POWER button for 10 seconds.

automatically shuts down. Turn the display on again after the projector cools down. If the problem persists, contact Dell: www.dell.com/contactDell.

If the projector fan fails, the projector will automatically shut down. Try to clear the projector mode by pressing and holding the Power button for 10 seconds. Please wait for about 5 minutes and try to power up again. If the problem persists, contact Dell: www.dell.com/contactDell.

The battery may be low. If so, replace with two new AAA batteries.

36 Troubleshooting

Guiding Signals

Projector

Status

Standby mode

Warming up mode

Lamp on Projector in Normal mode, ready to

Cooling mode

Projector overheated

Fan breakdown

Lamp driver breakdown

Color Wheel breakdown

Lamp failure Lamp is defective. Replace the lamp. OFF OFF AMBER

Fault - DC supply (+12V)

Lamp module connection failed

Projector in Standby mode. Ready to power on.

Projector takes some time to warm up and power on.

display an image.

accessed.

Projector is cooling to shutdown.

Air vents might be blocked or ambient temperature may be above 40°C. The projector automatically shuts down. Ensure that the air vents are not blocked and that the ambient temperature is within operational range. If the problem persists, contact Dell.

One of the fans has failed. The projector automatically shuts down. If the problem persists, contact Dell.

The lamp driver has failed. The projector automatically shuts down. Unplug the power cord. After three minutes plug the power cord and turn the display on again. If this problem persists, contact Dell.

Color wheel cannot start. The projector has failed and the projector automatically shuts down. Unplug the power cord. After three minutes plug the power cord and turn the display on again. If this problem persists, contact Dell.

Power supply has been interrupted. The projector automatically shuts down. Unplug the power cord. After three minutes plug the power cord and turn the display on again. If this problem persists, contact Dell.

Lamp module connection may be disrupted. Check the lamp module and ensure that it is properly installed. If the problem persists, contact Dell.

Description

Note: The OSD menu is not

Control Buttons Indicator

Power

White Flashing OFF OFF

White OFF OFF

OFF AMBER OFF

OFF

AMBER Flashing OFF

White

AMBER Flashing AMBER AMBER

OFF OFF

TEMP

(Amber)

AMBER

Flashing

AMBER

Flashing

LAMP

(Amber)

OFF

AMBER

Flashing

AMBER

Flashing

AMBER

Flashing

Troubleshooting 37

Maintenance

Changing the Lamp

CAUTION: Before you begin any of the procedures in this section,

follow the Safety Instructions as described on page 9.

Replace the lamp when the message "Lamp is approaching the end of its useful life in the operation. Replacement suggested! www.dell.com/lamps" appears on the screen. If this problem persists after

replacing the lamp, contact Dell.

CAUTION: Use an original lamp to ensure safe and optimal

working condition of your projector.

CAUTION: The lamp becomes very hot when in use. Do not

attempt to replace the lamp until the projector has been allowed to cool down for at least 30 minutes.

CAUTION: Do not touch the bulb or the lamp glass at any time.

Projector lamps are very fragile and may shatter if touched. The shattered glass pieces are sharp and can cause injury.

CAUTION: If the lamp shatters, remove all broken pieces from the

projector and dispose or recycle according to state, local, or federal law. For more information see www.dell.com/hg.

Turn off the projector and disconnect the power cord.

Let the projector cool for at least 30 minutes.

Loosen the screw that secures the top cover, and remove the cover.

Loosen the screw that secures the lamp.

Pull the lamp up by its metal handle.

NOTE: Dell may require lamps

replaced under warranty to be returned to Dell. Otherwise, contact your local waste disposal agency for the address of the nearest deposit site.

Replace with the new lamp.

Tighten the screw that secures the lamp.

38 Maintenance

Replace the top cover and tighten the screw.

Reset the lamp usage time by selecting "Yes" for

Power Settings

of the

Advanced Settings

Lamp Reset

in the OSD

menu. When a new lamp module has been changed, the projector will automatically detect and reset the lamp hours.

CAUTION: Lamp Disposal (for the US only)

LAMP(S) INSIDE THIS PRODUCT CONTAIN MERCURY AND MUST BE RECYCLED OR DISPOSED OF ACCORDING TO LOCAL, STATE, OR FEDERAL LAWS. FOR MORE INFORMATION, GO TO WWW.DELL.COM/HG OR CONTACT THE ELECTRONIC INDUSTRIES ALLIANCE AT WWW.EIAE.ORG. FOR LAMP-SPECIFIC DISPOSAL INFORMATION, CHECK WWW.LAMPRECYCLE.ORG.

Maintenance 39

Replacing Remote Control Batteries

AAA

NOTE: Remove the batteries from the remote control when not in

use.

Press the tab to lift the battery compartment cover.

Check the polarity (+/-) marking on the batteries.

Insert the batteries and align their polarity correctly according to the marking in the battery compartment.

NOTE: Avoid mixing different types of batteries

or using new and old batteries together.

AAA

Slip the battery cover back.

40 Maintenance

Specifications

Light Valve 0.65" 1080p S600 DMD, DarkChip3™ Brightness 3400 ANSI Lumens (Max.) Contrast Ratio 1800:1 Typical (Full On/Full Off) Uniformity 80% Typical (Japan Standard - JBMA) Number of Pixels 1920 x 1080 (1080p) Aspect Ratio 16:9 Displayable Color 1.07 billion colors Color Wheel Speed 2 X

1 X for 3D Display

Projection Lens Fixed Lens(WA21), F#/2.4

Throw ratio =UST TR0.25

Offset ratio: 118.5 ± 5%

Projection Screen Size 81 ~100 inches

Optimized size: 89.1 inches Projection Distance 1.46 ~1.83ft (44.6cm ~55.8) Video Compatibility Composite Video:

NTSC: M (3.58 MHz), 4.43 MHz

PAL: B, D, G, H, I, M, N, 4.43 MHz

SECAM: B, D, G, K, K1, L, 4.25/4.4 MHz

Component Video input via VGA: 1080i (50/60

Hz), 720p (50/60 Hz), 576i/p, 480i/p

HDMI input: 1080p, 720p, 576i/p, 480i/p Power Supply Universal AC 90~264 V 50-60 Hz with PFC

input

Specifications 41

Power Consumption Normal mode: 320 W ± 10% @ 110 Vac

4.06"(103 mm)

15.08"(383 mm)

12.52"(318 mm)

Eco mode: 270 W ± 10% @ 110 Vac

Standby mode: < 0.5 W

Network standby: < 3 W

NOTE: By default, the projector is set to

enter power saving mode after 20

minutes of inactivity. Audio 2 speaker x 10 watt RMS Noise Level Normal mode: 36 dB(A)

Eco mode: 32 dB(A) Projector Weight 10.36 lbs (4.7kg) Dimensions (W x H x D) 15.08 x12.52 x 4.06 inches (383 x 318 x 103

mm)

Environmental Operating temperature: 5 °C - 40 °C (41 °F-

104 °F)

Humidity: 80% maximum

orage temperature: 0 °C to 60 °C (32 °F to 140 °F) Humidity: 90% maximum

Shipping temperature: -20 °C to 60 °C (-4 °F to 140 °F) Humidity: 90% maximum

I/O Connectors Power: One AC power socket (3-pin - C14

inlet)

42 Specifications

VGA input: One 15-pin D-sub connector (Blue), VGA In, for analog RGB/Component input signals.

VGA output: One 15-pin D-sub connector (Black) for VGA loop through.

Composite Video input: One Yellow RCA jack for CVBS signal.

HDMI input: Two HDMI connectors for supporting HDMI 1.4a. specification HDCP compliant.

Analog Audio input: One 3.5 mm stereo mini phone jack (Blue)/ One x Audio In RCA pair (L/R)

Variable audio output: One 3.5 mm stereo mini phone jack (Green).

Analog Audio input:Two 3.5 mm stereo mini phone jack(Blue) and two pair of RCA connector (Red/White)

Microphone : One 3.5 mm stereo mini phone jack (Pink).

USB (mini USB) port: One mini USB slave for firmware upgrade/ interactive.

5V/1.8A output: One USB type A 5V DC / 1.8 A output for support dongle power.

RS232 port: One 9-pin D-sub for RS232 communication.

RJ-45 port: One RJ-45 connector for build-in for network control.

Touch Unit: one Curtain Module power Jack Lamp PHILIPS 260 W user-replaceable lamp Lamp life Normal mode: Up to 3000 hours

Eco mode: Up to 5000 hours

NOTE: The lamp life rating for any projector is a measure of

brightness degradation only, and is not a specification for the time it takes a lamp to fail and cease light output. Lamp life is defined as the time it takes for more than 50 percent of a lamp sample population to have brightness decrease by approximately 50 percent of the rated lumens for the specified lamp. The lamp life rating is not guaranteed

Specifications 43

in any way. The actual operating life span of a projector lamp will vary according to operating conditions and usage patterns. Usage of a projector in stressful conditions which may include dusty environments, under high temperatures, many hours per day, and abrupt powering-off will most likely result in a lamp’s shortened operating life span or possible lamp failure.

44 Specifications

Additional Information

For additional information on how to use your projector, please see the Dell Projectors User Guide at www.dell.com/support/manuals.

Additional Information 45

Contacting Dell

For customers in the United States, call 800-WWW-DELL (800-999-3355).

NOTE: If you do not have an active Internet connection, you can find

contact information on your purchase invoice, packing slip, bill, or Dell product catalog.

Dell provides several online and telephone-based support and service options. Availability varies by country and product, and some services may not be available in your area. To contact Dell for sales, technical support, or customer service issues:

Visit go to www.dell.com/contactDell.

Select your region on the interactive map.

Select a Segment for Contact.

Select the appropriate service or support link based on your need.

46 Contacting Dell

Index

Adjusting Projector Focus 10, 31

Changing the Lamp 38

Connection Ports

Audio Input connector Audio Output connector Audio RCA connector Composite Video connector

8 HDMI 1 connector HDMI 2 connector Microphone connector Mini USB (Mini Type B) Power cord connector RJ 45 connector RS232 connector Touc h Un it p o we r USB A connector VGA In connector VGA Out connector (monitor

loop through)

Contact Dell

5, 38

Interactive Pen

Battery Pen tip Power indicator Power switch Wrist strap holder

Main Unit 7

Camera Infrared (IR) receivers Lamp cover Lens

Power button

phone numbers 46

Remote Control 12

Dell

contacting

45, 46

Specifications

Aspect Ratio Audio

Brightness

Index 47

Color Wheel Speed 41 Contrast Ratio Dimensions Displayable Color Environmental I/O Connectors Light Valve Noise Level Number of Pixels Power Consumption Power Supply Projection Distance Projection Lens Projection Screen Size Projector Weight Uniformity Video Compatibility

support

contacting Dell

45, 46

telephone numbers 46

48 Index

Dell S560T, S560P User Manual

Specifications and Main Features

Frequently Asked Questions

User Manual

About Your Dell Projector

Projector Box Contents

Projector Top and Bottom View

Top View Bottom View

Projector Connections

Adjusting Image Size

Adjusting Image Shape

Remote Control

Remote Control Operating Range

System Requirements

16 Using Interactive Pen (Only for S560P)

About Your Interactive Pen

Replacing the Interactive Pen Tips

Replacing the Interactive Pen Batteries

Using Interactive Pen with S560P

Touch Area Setting

Pen Calibration

System Requirements

24 Using Interactive Touch (Only for S560T)

Setting Up Interactive Touch

Using Interactive Touch with S560T

Touch Area Setting

Interactive Touch Calibration

Using S560T and Dry Erase Whiteboard

Installing Wireless Display Adapter

Connecting Wireless Display Adapter 31

Setting up the Wireless Display Adapter

Troubleshooting

Troubleshooting Tips

Guiding Signals

Maintenance

Changing the Lamp

Replacing Remote Control Batteries

Specifications

Additional Information

Contacting Dell