Dell OptiPlex 7460 User Manual
Dell OptiPlex All-in-One
Stand Installation Guide
Notes, cautions, and warnings
NOTE: A NOTE indicates important information that helps you make better use of your product.
CAUTION: A CAUTION indicates either potential damage to hardware or loss of data and tells you how to avoid the problem.
WARNING: A WARNING indicates a potential for property damage, personal injury, or death.
© 2018 Dell Inc. or its subsidiaries. All rights reserved. Dell, EMC, and other trademarks are trademarks of Dell Inc. or its subsidiaries. Other trademarks
may be trademarks of their respective owners.
2018 - 11
Rev. A00
Contents
1 Before you begin............................................................................................................................................ 4
Safety instructions.............................................................................................................................................................4
Before working inside your computer........................................................................................................................4
Safety precautions....................................................................................................................................................... 5
After working inside your computer...........................................................................................................................5
2 Basic stand for Dell OptiPlex 5260 and 7460 All-in-One................................................................................ 6
Installing the basic stand................................................................................................................................................... 6
Removing the basic stand.................................................................................................................................................7
Basic stand tilt.................................................................................................................................................................... 8
3 Height adjustable stand for Dell OptiPlex 5260, 7460, and 7760 All-in-One................................................... 9
Installing the height adjustable stand...............................................................................................................................9
Removing the height adjustable stand...........................................................................................................................10
Height adjustable stand transform................................................................................................................................. 12
4 Height adjustable stand with optical disk drive for Dell OptiPlex 5260 and 7460 All-in-One..........................13
Installing the height adjustable stand with optical disk drive.......................................................................................13
Removing height adjustable stand with optical disk drive........................................................................................... 14
Height adjustable stand with optical drive transform.................................................................................................. 16
5 Articulating stand for Dell OptiPlex 5260,7460, and 7760 All-in-One............................................................ 17
Installing the articulating stand........................................................................................................................................17
Removing the Articulating Stand....................................................................................................................................17
Articulating stand tilt transform......................................................................................................................................18
6 Getting help................................................................................................................................................. 19
Contacting Dell..................................................................................................................................................................19
Contents
3
Before you begin
Safety instructions
Use the following safety guidelines to protect your computer from potential damage and to ensure your personal safety. Unless otherwise
noted, each procedure included in this document assumes that the following conditions exist:
• You have read the safety information that shipped with your computer.
• A component can be replaced or, if purchased separately, installed by performing the removal procedure in reverse order.
WARNING: Disconnect all power sources before opening the computer cover or panels. After you nish working inside the
computer, replace all covers, panels, and screws before connecting to the power source.
WARNING: Before working inside your computer, read the safety information that shipped with your computer. For additional
safety best practices information, see the Regulatory Compliance Homepage
CAUTION: Many repairs may only be done by a certied service technician. You should only perform troubleshooting and simple
repairs as authorized in your product documentation, or as directed by the online or telephone service and support team.
Damage due to servicing that is not authorized by Dell is not covered by your warranty. Read and follow the safety instructions
that came with the product.
CAUTION: To avoid electrostatic discharge, ground yourself by using a wrist grounding strap or by periodically touching an
unpainted metal surface at the same time as touching a connector on the back of the computer.
CAUTION: Handle components and cards with care. Do not touch the components or contacts on a card. Hold a card by its
edges or by its metal mounting bracket. Hold a component such as a processor by its edges, not by its pins.
CAUTION: When you disconnect a cable, pull on its connector or on its pull-tab, not on the cable itself. Some cables have
connectors with locking tabs; if you are disconnecting this type of cable, press in on the locking tabs before you disconnect the
cable. As you pull connectors apart, keep them evenly aligned to avoid bending any connector pins. Also, before you connect a
cable, ensure that both connectors are correctly oriented and aligned.
NOTE: The color of your computer and certain components may appear dierently than shown in this document.
1
Before working inside your computer
To avoid damaging your computer, perform the following steps before you begin working inside the computer.
1 Ensure that you follow the Safety Instruction.
2 Ensure that your work surface is at and clean to prevent the computer cover from being scratched.
3 Turn o your computer.
4 Disconnect all network cables from the computer.
CAUTION
network device.
5 Disconnect your computer and all attached devices from their electrical outlets.
6 Press and hold the power button while the computer is unplugged to ground the system board.
NOTE
unpainted metal surface at the same time as touching a connector on the back of the computer.
4 Before you begin
: To disconnect a network cable, rst unplug the cable from your computer and then unplug the cable from the
: To avoid electrostatic discharge, ground yourself by using a wrist grounding strap or by periodically touching an
Safety precautions
The safety precautions chapter details the primary steps to be taken before performing any disassembly instructions.
Observe the following safety precautions before you perform any installation or break/x procedures involving disassembly or reassembly:
• Turn o the system and all attached peripherals.
• Disconnect the system and all attached peripherals from AC power.
• Disconnect all network cables, telephone, and telecommunications lines from the system.
• Use an ESD eld service kit when working inside any desktop to avoid electrostatic discharge (ESD) damage.
• After removing any system component, carefully place the removed component on an anti-static mat.
• Wear shoes with non-conductive rubber soles to reduce the chance of getting electrocuted.
Standby power
Dell products with standby power must be unplugged before you open the case. Systems that incorporate standby power are essentially
powered while turned o. The internal power enables the system to be remotely turned on (wake on LAN) and suspended into a sleep
mode and has other advanced power management features.
Unplugging, pressing and holding the power button for 15 seconds should discharge residual power in the system board. .
After working inside your computer
After you complete any replacement procedure, ensure that you connect any external devices, cards, and cables before turning on your
computer.
1 Connect any telephone or network cables to your computer.
CAUTION
computer.
2 Connect your computer and all attached devices to their electrical outlets.
3 Turn on your computer.
4 If required, verify that the computer works correctly by running ePSA diagnostics.
: To connect a network cable, rst plug the cable into the network device and then plug it into the
Before you begin
5
Basic stand for Dell OptiPlex 5260 and 7460 All-
in-One
Topics:
• Installing the basic stand
• Removing the basic stand
• Basic stand tilt
Installing the basic stand
1 Follow the procedure in Before working inside your computer.
2 Insert the stand base into the slot on the basic stand.
2
3 Tighten the captive screw to secure the stand base to the basic stand.
6 Basic stand for Dell OptiPlex 5260 and 7460 All-in-One
Loading...