DATEL DMS-20PC-1-AS, DMS-20PC-3-YS, DMS-20PC-3-RSH, DMS-20PC-3-RS, DMS-20PC-3-RL Datasheet

DATEL, Inc., Mansfield, MA 02048 (USA) • Tel: [phone] Fax: [phone] • E-mail: [e-mail] • Internet: www.datel.com

Features

DMS-20PC Series, 3½ Digit, LED Display, Digital Panel Voltmeters combine a

precision A/D converter; a factory-trimmed, highly stable, voltage reference; and a

large (0.37"/9.4mm), easy-to-read LED display in a single package that is only

slightly larger than the display itself. Displays are offered in either red, orange,

amber, yellow or green colors. High-intensity and low-power (35mW total) red LED's

are also optional.

These low-cost meters are fully self-contained and fully functional. Their

subminiature (1.38" x 0.88" x 0.48"), epoxy-encapsulated cases incorporate built-in

color filters and bezels; are moisture and vibration proof; and function well in the

harshest environments. Their 12-pin, dual-in-line configuration offers component-like,

plug-in convenience and maximum versatility. Operating temperature range is 0 to

+60°C.

The meters come with one of four, differential, input voltage ranges: ±200mV, ±2V

±20V or ±200V. Input impedance is a minimum 800kΩ. CMRR is typically 86dB (dc

to 60Hz), and CMV is ±2V. Input overvoltage protection (on the non-inverting input)

is ±250V. Devices are fully calibrated at the factory to an accuracy of ±1 count

(±0.05% of full scale range) and never require calibration or adjustment.

A DISPLAY ENABLE function permits the display to be disabled for "power-

down" operation. All models have a DISPLAY TEST function. Standard red LED

models offer an optional DISPLAY HOLD function.

Small size, low cost and adjustment-free reliability make the DMS-20PC Series

the best choice for all your 3½ digit, LED, DPM applications.

Figure 1. DMS-20PC Series Simplified Schematic

••

••

•

Lowest-cost LED meters

••

••

•

Subminiature size:

1.38" x 0.88" x 0.48"

35mm x 22mm x 12mm

••

••

•

Large (0.37"/9.4mm) LED display

••

••

•

Choice of 5 LED colors

••

••

•

High-intensity or low-power (7mA) red

LED's optional

••

••

•

Epoxy-encapsulated, 12-pin DIP package

with built-in color filter and bezel

••

••

•

4 differential input voltage ranges

••

••

•

Factory calibrated, ±1 count accuracy

••

••

•

Single +5V power supply

••

••

•

User-selectable decimal point placement

••

••

•

DISPLAY ENABLE function for

"power-down" mode

••

••

•

DISPLAY TEST and HOLD (optional)

functions

••

••

•

0 to +60°C temperature range

3½ Digit, LED Display

Low-Cost, Subminiature

Digital Panel Voltmeters

DMS-20PC Series

Actual Size

(+) INPUT HI

(–) INPUT LO

ANALOG

COMMON

REFERENCE OUT

REFERENCE IN

+5V SUPPLY

R1

DP 1

DP 2

DP 3

6

5

4

11

12

10

8

7

1

3

DC/DC

CONVERTER

2

5V RETURN

+5V

–5V

R2

»

+2.0V

DATA

909k

V+

V–

A/D

CONVERTER

0 Vdc

0.01

µF

9

DISPLAY

ENABLE

+5V

R2 is not used on ± 2 0 0 mV (-0) models or ±2V (-1) mode ls.

R2 = 100k on ±20V (-2) models and 9.1k on ±200V (-3) models.

Only used on ±200mV (-0) and ±2V (-1) models.

DISPLAY

TEST/HOLD

11

Pin 9 is DISPLAY TEST on all but eight models. On those models

(

-H option

)

, it is DISPLAY HO L D.

1

2

3

2

1

3

®®

www.datel.com

2

DMS-20PC

3½ DIGIT, LED DISPLAY DIGITAL PANEL VOLTMETERS

Performance/Functional Specifications

Typical at TA = +25°C and supply voltage = +5V using the single-ended input circuit,

unless otherwise noted.

➀

Applies for transient or continuous overvoltages applied to (+) INPUT HI (pin 11)

with (–) INPUT LO (pin 12) properly connected. Pin 12 is not overvoltage protected

(see Figure 1). Voltages applied to pin 12 should not exceed the supply voltage.

➁

See Technical Notes.

➂

The DISPLAY HOLD function is optional on standard red and green LED models only.

See Ordering Information.

Leave blank for standard

models.

Add -H for DISPLAY

HOLD option (available on

standard red and green

LED models only).

DMS-20PC-1- RS

LED Color:

AS = Standard Amber

GS = Standard Green

OS = Standard Orange

RS = Standard Red

YS = Standard Yellow

RH = High-Intensity Red

RL = Low-Power Red

Accessories:

DMS-20-CP Panel cutout punch

DMS-BZL3 DMS-20 bezel assembly

DMS-BZL4 DMS-20 bezel assembly with sealing gasket

DMS-EB2 Application/evaluation board with standard

MOLEX connector, decimal point solder pads

and attenuation resistor pads.

T echnical Notes

1. REFERENCE OUTPUT (Pin 8) and INPUT (Pin 7): Pin 8 is a

precision reference actively trimmed at the factory. In normal

operation, pin 8 must be tied to pin 7 to achieve all listed accuracy

and drift specifications.

2. ANALOG COMMON (Pin 10): This pin is connected to an internal,

low-noise, "relative" ground. It is used in certain differential and

"floating" measurements as described in the Applications section

of this data sheet and Ap Note 3 of the DATEL Panel Meter Catalog.

Pin 10 should not be connected to pin 3 (5V RETURN) or to

your system’s analog ground.

3. Decimal Point Placement: The location of the decimal point is

user-selectable, and the decimal point control pins (DP1-DP3) are

active low functions. Select the appropriate decimal point by tying

the appropriate pin (pin 4, 5 or 6) to pin 3 (5V RETURN). Unused

decimal point location pins should be left open.

Hard wiring is preferable, however, you can use logic gates to

exercise dynamic control over the location of the decimal point if the

following drive conditions are met:

Model Applied "0" Voltage Load Current*

DMS-20PC-X-RL +0.05V max. 0.7mA max.

All Others +0.4V max. 6mA max.

* The driving gates must be able to sink this much current

(I

OL) with a logic "0" output.

Ordering Information

Input Range:

0 = ±200mV

1 = ±2V

2 = ±20V

3 = ±200V

A panel-mount retaining clip is supplied with each model.

Analog Inputs Min. Typ. Max. Units

Full Scale Input Range:

DMS-20PC-0 -- ±200 -- m V

DMS-20PC-1 -- ±2 -- Volts

DMS-20PC-2 -- ±20 -- Volts

DMS-20PC-3 -- ±200 -- Volts

Input Impedance:

DMS-20PC-0, -1 100 1000 -- M

Ω

DMS-20PC-2, -3 0.8 1 -- M

Ω

Overvoltage Protection

➀

-- -- ±250 Volts

Common Mode Voltage Range -- -- ±2 Volts

CMRR (dc to 60Hz) -- 86 -- dB

Control Inputs ➁ ➂

Decimal Point Placement (Pins 4-6) Tie to pin 3 to activate

Display Test (Pin 9) Tie to pin 1 to activate all segments

Display Hold (Pin 9)

➂

Tie to pin 1 to hold last reading

Performance

Sampling Rate 2.5 samples per second

Accuracy (3 minute warm-up):

DMS-20PC-0 (VIN = +0.19V) -- ±1 ±3 Counts

DMS-20PC-1 (VIN = +1.9V) -- ±1 ±3 Counts

DMS-20PC-2 (VIN = +19V) -- ±2 ±3 Counts

DMS-20PC-3 (VIN = +190V) -- ±2 ±3 Counts

Zero Reading (VIN = 0 Volts) "–001" "000" "001"

Temperature Drift (0 to +60°C) -- ±0.2 ±0.4 Cnts/°C

Power Supply Requirements

Supply Voltage + 4.75 +5.00 +5.25 Volts

Supply Current:

DMS-20PC-X-RS -- +60 +90 mA

DMS-20PC-X-RL -- +7 +12 mA

DMS-20PC-X-AS -- +90 +120 mA

DMS-20PC-X-GS -- +90 +120 mA

DMS-20PC-X-OS -- +90 +120 mA

DMS-20PC-X-YS -- +90 +120 mA

DMS-20PC-X-RS-H -- +60 +90 mA

DMS-20PC-X-GS-H -- +90 +120 mA

DMS-20PC-X-RH -- +6 0 +90 mA

Display

Display Type and Size 3½ Digit LED, 0.37"/9.4mm high

Polarity Indication Autopolarity ("–" for negative VIN)

Overrange Indication "–1___" for negative VIN

"1___" for positive VIN

Physical/Environmental

Operating Temperature 0--+60°C

Storage Temperature –40 -- +75 °C

Humidity (Non-condensing) 0 -- 95 %

Case Material Polycarbonate

Weight 0.4 ounces (11 grams)

Order on-line at www.datel.com