The HMC350MS8 is a miniature single balanced
mixer in an 8 lead plastic surface mount package. The passive GaAs schottky diode mixer
implements planar on chip Baluns and requires
no external components. The mixer can be used
as an upconverter, down converter, or modulator. It is especially suited for cellular base
station, cable modem, and fixed wireless access systems that operate between 600 and
1200 MHz. The mixer provides 7.5 dB conversion loss and +25 dBm IIP3 with LO drive levels
of +19 dBm at mid-band. The design was optimized for low cost high volume applications
where high converter linearity is required.
SMT
Guaranteed Performance, LO Drive= +19 dBm, -40 to +85 deg C
12 Elizabeth Drive, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373Web Site: www.hittite.com
4 - 212
Page 4
MICROWAVE CORPORATION
HIGH IP3 SINGLE-BALANCED MIXER 0.6 - 1.2 GHz
HMC350MS8
V00.1200
Schematic
LO
(PIN 1
)
IF (PIN 5
Outline Drawing
RF
(PIN 8
)
GND
(PINS 2, 3, 4, 7)
)
FEBRUARY 2001
Absolute Maximum Ratings
tupnIFI/FRmBd72+
evirDOLmBd72+
erutarepmeTegarotSCged051+ot56-
erutarepmeTgnitarepOCged58+ot55-
tnerruCCDFIAm81±
4
MIXERS
1. MATERIAL:
A) PACKAGE BODY - LOW STRESS INJECTION-MOLDED PLASTIC,
SILICA & SILICONE IMPREGNATED.
B) LEADFRAME MATERIAL: COPPER ALLOY
2 . PLATING : LEAD - TIN SOLDER PLATE
3. DIMENSIONS ARE IN INCHES (MILLIMETERS).
12 Elizabeth Drive, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373Web Site: www.hittite.com
UNLESS OTHERWISE SPECIFIED ALL TOL. ARE ±0.005 (±0.13).
4. ALL UNLABELED LEADS ARE GROUND.
5. CHARACTERS TO BE HELVETICA MEDIUM, APPROX .030 HIGH
WHITE INK, LOCATED APPROXIMATELY AS SHOWN.
6. DIMENSION DOES NOT INCLUDE MOLDFLASH OF 0.15 MM PER SIDE
7. DIMENSION DOES NOT INCLUDE MOLDFLASH OF 0.25 MM PER SIDE
4 - 213
SMT
Page 5
MICROWAVE CORPORATION
HIGH IP3 SINGLE-BALANCED MIXER 0.6 - 1.2 GHz
HMC350MS8
4
MIXERS
FEBRUARY 2001
Evaluation PCB for HMC350MS8
V00.1200
The circuit board used in the final application should use RF circuit design techniques. Signal lines should have
50 ohm impedance while the package ground leads should be connected directly to the ground plane similar to
SMT
that shown. A sufficient number of via holes should be used to connect the top and bottom ground planes. The
evaluation circuit board as shown is available from Hittite upon request.
Evaluation Circuit Board
metInoitpircseD
3J,2J,1JFRAMStnuoMCProtcennoC
1UrexiM8SM053CMH
*
BCP
12 Elizabeth Drive, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373Web Site: www.hittite.com
4 - 214
828101
draoBlavE
0534sregoR:lairetaMdraoBtiucriC*
Page 6
MICROWAVE CORPORATION
HIGH IP3 SINGLE-BALANCED MIXER 0.6 - 1.2 GHz
HMC350MS8
V00.1200
NOTES:
FEBRUARY 2001
4
MIXERS
12 Elizabeth Drive, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373Web Site: www.hittite.com
4 - 215
SMT
Loading...
+ hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.