Datasheet 53111-2ZA, 53111-2YC, 53111-2YA, 53111-2XC, 53111-2XA Datasheet (MII)

53111

DSCC Approved 5962-9314001 and 5962-9314002

Features:

•

•

•

•

•

•

Hermetically Sealed 8-Pin Dual-In-Line
package
Small Size and Weight
Options: 5mA or 10mA input forward current
Performance Guaranteed over –55°C to
+125°C Ambient Temperature Range
AC/DC Signal & Power Switching
Maximum Average Current

POWER MOSFET OPTOCOUPLER,

90 V/1 Ω, Hermetically Sealed,

Applications:

Satellite/Space Systems

•

Military/High Reliability Systems

•

Standard 28 VDC and 48 VDC Load Driver

•

Standard 24 VAC Load Driver

•

•

AC/DC Electromechanical and Solid State
Relay Replacement

•

I/O Modules

Mii

MICROCIRCUITS PRODUCTS

DIVISION

AC/DC: 0.8 A

DC only: 1.6 A

1500 VDC Withstand Test Voltage

•

High Transient Immunity

•

5 A Output Surge Current

•

Shock and Vibration Resistant

•

MIL-PRF-38534 Compliant

•

Equivalent to HSSR7111/7112

•

DESCRIPTION

The 53111 is a single channel, hermetically sealed, power MOSFET optocoupler. Low on-resistance of the
MOSFET output, combined with 1500 VDC isolation between input and output, makes this optocoupler ideal for
solid state relay applications. Operation is specified over the full military temperature range. The part is supplied in
an eight-pin, dual-in-line ceramic package, available as COTS, as fully compliant MIL-PRF-38534 Class H device,
or with custom screening. Lead options support both through-hole and surface-mount assembly. The part is
normally shipped with gold plated leads, but lead finishes per MIL-PRF-38534 are available.

Functionally, the device operates as a single-pole, normally open (1 Form A) solid state relay. The device is
actuated by an input current, which can be supplied from standard logic types such as open-collector TTL. The
input current biases a light emitting diode that is optically coupled to an integrated photovoltaic diode array. The
photovoltaic array powers control circuitry that operates the output MOSFETs.

Optimum switching of either AC or DC loads is provided by a configurable output. For AC loads, connection A in
Figure 1 must be used. Connection A will also switch DC loads but connection B, in Figure 1, provides DC-only
operation with the advantages of substantial reduction in on-resistance and twice the output current capability as
that obtained with connection A.

Micropac Industries cannot assume any responsibility for any circuits shown or represent that they are free from patent infringement.

Micropac reserves the right to make changes at any time in order to improve design and to supply the best product possible.

MICROPAC INDUSTRIES, INC. MICROCS PRODUCTS DIVISION • 905 E. Walnut St., Garland, TX 75040 • [phone] • Fax [phone]

www.micropac.com

E-MAIL: [e-mail] 5/22/02

Pg. 1 of 11

53111 Power MOSFET Optocoupler

___________________________________________________________________________________________

ABSOLUTE MAXIMUM RATINGS

Storage Temperature Range ..................................................................................................................-65°C to +150°C

Operating Ambient Temperature - T
Junction Temperature - T

........................................................................................................................................150°C

J

Operating Case Temperature - T

.....................................................................................................-55°C to +125°C

A

.....................................................................................................................+145°C

C

(1)

Lead Solder Temperature (1.6mm below seating plane).......................................................................... 260°C for 10s

Average Input Current - I
Peak Repetitive Input Current - I
Peak Surge Input Current - I
Reverse Input Voltage - V

........................................................................................................................................20 mA

F

…(Pulse Width < 100ms; duty cycle < 50%) ...............................................40 mA

Fpk

surge…(Pulse Width < 0.2ms; duty cycle < 0.1%)........................................ 100 mA

FPK

....................................................................................................................................5 V

R

Average Output Current
Connection A – I
Connection B - I

............................................................................................................................................0.8 A

O

............................................................................................................................................1.6 A

O

Single Shot Output Current - Figure 4
Connection A - I
Connection B - I

surge…(Pulse width < 10ms) .............................................................................................5 A

Opk

surge…(Pulse width < 10ms) ...........................................................................................10 A

Opk

Output Voltage
Connection A - V
Connection B - V

Average Output Power Dissipation - Figure 5 ............................................................................................ 800 mW

............................................................................................................................ -90 V to +90 V

O

............................................................................................................................... 0 V to +90 V

O

(2)

RECOMMENDED OPERATING CONDITIONS:

PARAMETER SYMBOL DEVICE

MIN MAX UNITS

TYPE

I

F (ON)

Input Voltage (off) V

F (OFF)

Operating Temperature T

-01

-02 5 20 mA
All

A

All

10 20 mA Input Current (on)

0 0.6 VDC

-55 +125 °C

Micropac Industries cannot assume any responsibility for any circuits shown or represent that they are free from patent infringement.

Micropac reserves the right to make changes at any time in order to improve design and to supply the best product possible.

MICROPAC INDUSTRIES, INC. MICROCS PRODUCTS DIVISION • 905 E. Walnut St., Garland, TX 75040 • [phone] • Fax [phone]

www.micropac.com

E-MAIL: [e-mail] 5/22/02

Pg. 2 of 11

53111 Power MOSFET Optocoupler

ELECTRICAL SPECIFICATIONS

T

= -55°C to +125°C, unless otherwise specified.

A

Parameter Sym. Min. Typ.* Max. Units Test Conditions Notes

= 0.6 V

V

Output Withstand Voltage V

Output On-Resistance
(Connection A)

Output On-Resistance
(Connection B)

90 110 V

O(OFF)

R

(ON)

0.40

1.0

0.12 0.25

Ω

Ω

F

= 10 µA

I

O

I

= 10 mA (for –01)

F

I

= 5 mA (for –02)

F

= 800 mA

I

O

(pulse duration ≤ 30 ms)

I

= 10 mA (for –01)

F

I

= 5 mA (for –02)

F

I

= 1.6 A

O

Figure

(pulse duration ≤ 30 ms)

= 0.6 V

V

Output Leakage Current I

10-4 10

O (OFF)

A

µ

Input Forward Voltage VF 1.0 1.24 1.7 V

Input Reverse Breakdown
Voltage

5.0 V

V

R

F

V

= 90 V

O

= 10 mA (for –01)

I

F

I

= 5 mA (for –02)

F

I

= 100 µA

R

RH ≤ 45%, t = 5 s

Input-Output Insulation I

Turn-On Time tON 1.25 6.0 ms

Turn-Off time t

Output Transient
Rejection

Input-Output Transient
Rejection

1.0

I-O

0.02 0.25 ms

OFF

dV

/dt 1000

O

dV

/dt 500

I-O

A

µ

V/µs

V/µs

V

I-O

= 25°C

T

A

= 10 mA (for –01)

I

F

= 5 mA (for –02)

I

F

V

DD

I

= 800 mA

O

= 10 mA (for –01)

I

F

I

= 5 mA (for –02)

F

V

DD

I

= 800 mA

O

V

PEAK

C

M

C

= 15 pF

L

R

M

V

DD

V

I-O (PEAK)

= 20 kΩ

R

L

= 15 pF

C

L

= 1500 VDC

= 28 VDC

= 28 VDC

= 50 V

= 1000 pF

≥ 1 MΩ

= 5 V

= 50 V

4, 5

Figure

Figure

Figure

Figure

* All typical values are at T

= 25ºC, I

A

= 10 mA (for -01) or 5 mA (for –02), V

F (ON)

= 0.6V unless otherwise

F (OFF)

specified.

Micropac Industries cannot assume any responsibility for any circuits shown or represent that they are free from patent infringement.

Micropac reserves the right to make changes at any time in order to improve design and to supply the best product possible.

MICROPAC INDUSTRIES, INC. MICROCS PRODUCTS DIVISION • 905 E. Walnut St., Garland, TX 75040 • [phone] • Fax [phone]

www.micropac.com

E-MAIL: [e-mail] 5/22/02

Pg. 3 of 11

3,

1

6

6

7

8

53111 Power MOSFET Optocoupler

TYPICAL CHARACTERISTICS

All typical values are at T

= 25°C, I

A

= 10mA, V

F (ON)

= 0.6V unless otherwise specified.

F (OFF)

Parameter Symbol

Test

Typ. Units Notes

Conditions

Output Off-Capacitance C

Output Offset Voltage V

Input Diode Temperature
Coefficient

∆

O (OFF)

OS

V

F

/∆TA

Input Capacitance CIN

Input-Output
Capacitance

Input-Output Resistance R

C

I-O

I-O

O

f = 1 MHz

IF = 10 mA

= 0 mA

I

O

= 10 mA -1.4 mV/°C

I

F

= 0 V

V

F

f = 1 MHz

= 0 V

V

I-O

f = 1 MHz

= 500 V

V

I-O

t = 60 s

145 pF

2

V

µ

20 pF 7

1.5 pF 4

13

10

Ω

= 28 V

V

Notes:

1. Maximum junction to case thermal resistance for the device is 15ºC/W, where case temperature, TC, is
measured at the center of the package bottom.

2. For rating, see Figure 5. The output power P
average output current I

3. During the pulsed R

as shown in Figure 3.

O

measurement (IO duration < 30 ms), ambient (TA) and case temperature (TC) are equal.

ON

rating curve is obtained when the part is handling the maximum

D

4. Pins 2 through 3 shorted together and pins 5 through 8 shorted together.

5. This is a momentary withstand test, not an operating condition.

6. V

is a function of IF and is defined between pins 5 and 8, with pin 5 as the reference. VOS must be measured

OS

in a stable ambient (free of temperature gradients).

7. Zero-bias capacitance measured between the LED anode and cathode.

CAUTION:

Care should be taken not to exceed the maximum output power dissipation, maximum case temperature, and
maximum junction temperature when repetitively switching loads.

Micropac Industries cannot assume any responsibility for any circuits shown or represent that they are free from patent infringement.

Micropac reserves the right to make changes at any time in order to improve design and to supply the best product possible.

MICROPAC INDUSTRIES, INC. MICROCS PRODUCTS DIVISION • 905 E. Walnut St., Garland, TX 75040 • [phone] • Fax [phone]

www.micropac.com

E-MAIL: [e-mail] 5/22/02

6

4

Pg. 4 of 11

53111 Power MOSFET Optocoupler

Case outlines P, X, Y, AND Z

Terminal number Terminal symbol

Connection A Conneciton B
(AC or DC load) (DC load only)

1

2
3
4
5
6
7
8

NC
V
V
NC
V
NC
NC
V

F+
F-

O-

O+

NC
V
V
NC
V
NC
N
V

F+
F-

O+

O­O+

NC = No connection

CONNECTION A
AC/DC CONNECTION

I

O

1

I

F

2

+

V

F

3

-

8

+

7

V

O

6

I

F

+

V

F

-

CONNECTION B
DC CONNECTION

1

2

3

I

O

8

7

+

V

O

-

6

4

-

5 4 5

Figure 1 - Terminal Connections

INPUT OUTPUT

OFF OFF
ON ON

Figure 2 - Truth Table

Micropac Industries cannot assume any responsibility for any circuits shown or represent that they are free from patent infringement.

Micropac reserves the right to make changes at any time in order to improve design and to supply the best product possible.

MICROPAC INDUSTRIES, INC. MICROCS PRODUCTS DIVISION • 905 E. Walnut St., Garland, TX 75040 • [phone] • Fax [phone]

www.micropac.com

E-MAIL: [e-mail] 5/22/02

Pg. 5 of 11

53111 Power MOSFET Optocoupler

1.0

0.8

12

10

I

10 mA

≥

F

CONNECTION - B

8

0.6

6

0.4

CONNECTION - A

4

CONNECTION - A

10 mA

I

≥

F

__

-

0

-25 5

-55

T - AMBIENT TEMPERATURE - °C

A

-

θ

θ

CA
CA

= 40°C/W

= 80°C/W

35 65

95 125 155

OPK

I - SURGE - OUTPUT CURRENT - A

2

0

10

100

PULSE DURATION - ms

1000

I - OUTPUT CURRENT- A

0.2

O

Figure 3. Maximum Average Output Current Figure 4. Single Shot (nonrepetitive)
Rating vs. Ambient Temperature. Output Current vs. Pulse Duration.

MICROPAC INDUSTRIES, INC. MICROCS PRODUCTS DIVISION • 905 E. Walnut St., Garland, TX 75040 • [phone] • Fax [phone]

1.0

0.8

0.6

0.4

CONNECTION - A

0.2

DISSIPATION - W

D

P - OUTPUT POWER

0

-55

10 mA

I

≥

F

__

-

-25 5

T - AMBIENT TEMPERATURE - °C

A

-

θ

CA

θ

CA

= 40°C/W
= 80°C/W

35 65

95 125 155

Figure 5. Output Power Rating vs. Ambient Temperature.

Micropac Industries cannot assume any responsibility for any circuits shown or represent that they are free from patent infringement.

Micropac reserves the right to make changes at any time in order to improve design and to supply the best product possible.

www.micropac.com

E-MAIL: [e-mail] 5/22/02

Pg. 6 of 11

53111 Power MOSFET Optocoupler

PULSE GEN
(SEE NOTE 1)

I

F

MONITOR

I

R

200

1

8

F

2

+

V

F

-

3

4

7

6

5

M

V

DD

R

L

C

L

(SEE NOTE 2)

= 25 pF

V

O
MONITOR

NODE

I

V

GND

F

O

50%

PULSE
WIDTH

= 15 ms

90%

GND

50%

10%

t

ON

NOTES:

1. PULSE GENERATOR HAS THE FOLLOWING CHARACTERISTICS: OUTPUT IMPEDANCE = 50
AND t = t = 5.0 ns.

2. LOAD CAPACITANCE (C

r f

) INCLUDES PROBE AND JIG CAPACITANCE.

L

t

OFF

Figure 6. Switching Test Circuit and Waveform.

Micropac Industries cannot assume any responsibility for any circuits shown or represent that they are free from patent infringement.

Micropac reserves the right to make changes at any time in order to improve design and to supply the best product possible.

MICROPAC INDUSTRIES, INC. MICROCS PRODUCTS DIVISION • 905 E. Walnut St., Garland, TX 75040 • [phone] • Fax [phone]

www.micropac.com

E-MAIL: [e-mail] 5/22/02

Pg. 7 of 11

53111 Power MOSFET Optocoupler

V

M

INPUT

OPEN

1

I

F

2

+

V

F

-

3

4

8

7

6

5

C

V

O(PEAK)

+

M

R

-

PULSE
GENERATOR

MONITOR
NODE

M

90%

V

O(PEAK)

10%

t

r

V (MAX) < 5V

M

V

d

O

d

t

OVERSHOOT ON V

(0.8) V

=

O (PEAK)

t

r

OR

O (PEAK) IS TO BE < 10%

NOTES:

1. C INCLUDES PROBE AND FIXTURE CAPACITANCE.

2. R

M

INCLUDES PROBE AND FIXTURE RESISTANCE.

M

t

(0.8) V

90%

10%

f

O (PEAK)

t

f

Figure 7. Output Transient Rejection Test Circuit and Waveform.

Micropac Industries cannot assume any responsibility for any circuits shown or represent that they are free from patent infringement.

Micropac reserves the right to make changes at any time in order to improve design and to supply the best product possible.

MICROPAC INDUSTRIES, INC. MICROCS PRODUCTS DIVISION • 905 E. Walnut St., Garland, TX 75040 • [phone] • Fax [phone]

www.micropac.com

E-MAIL: [e-mail] 5/22/02

Pg. 8 of 11

53111 Power MOSFET Optocoupler

V

DD

R

L

S1

V

B

IN

V

I-0 (PEAK)

1

I

F

+

V

F

-

3

A

4

V

I-0 (PEAK)

+

-

8

72

6

5

V

O

C

L

PULSE
GENERATOR

t

90%

10%

f

10%

90%

t

r

V

O (OFF)

S

AT A (V = 0 V)

1

F

dV

I-0

dt

=

OVERSHOOT ON VOVERSHOOT ON V

V

O (ON)

S

AT B (NOTE 2)

1

(0.8) V

I-0 (PEAK)

t

r

I-0 (PEAK) IS TO BE < 10%

V

O (OFF)

OR

(MIN) > 3.25 V

(0.8) V

I-0 (PEAK)

t

f

V

O (ON)

(MAX) < 0.8 V

NOTES:

1. LOAD CAPACITANCE (C

2. FOR DEVICE TYPE 01, I =10mA,
FOR DEVICE TYPE 02, I =5mA.

)INCLUDES PROBE AND FIXTURE CAPACITANCE.

L

F
F

Figure 8. Input-Output Transient Rejection Test Circuit and Waveform.

Micropac Industries cannot assume any responsibility for any circuits shown or represent that they are free from patent infringement.

Micropac reserves the right to make changes at any time in order to improve design and to supply the best product possible.

MICROPAC INDUSTRIES, INC. MICROCS PRODUCTS DIVISION • 905 E. Walnut St., Garland, TX 75040 • [phone] • Fax [phone]

www.micropac.com

E-MAIL: [e-mail] 5/22/02

Pg. 9 of 11

53111 Power MOSFET Optocoupler

Case Outline P

.020 (0.51)

MIN

ESD

SYMBOL

PIN 1

.050 (1.27)
.035 (0.89)

.150 (3.81) MIN.

.110 (2.79)
.090 (2.29)

.050 (1.27)
.035 (0.89)

.110 (2.79)
.090 (2.29)

31757 USA

53111

XXXXX

Q

.390 (9.91)
.370 (9.41)

.390 (9.91)
.370 (9.41)

.020 (.051)

MAX.

.170 (4.32)

MAX.

.050 (1.27)
.030 (0.76)

.020 (0.51)

MAX.

Case Outline X

.170 (4.32)

MAX.

.320 (8.13)

MAX.

5°
0°

.013 (0.33)
.007 (0.18)

.320 (8.13)

MAX

.047 (1.19)

TYP

.390 (9.91)
.380 (7.87)

.310 (7.87)
.290 (7.37)

.065 (1.65)
.055 (1.40)

SEATING

PLANE

.180 (4.57)

MAX

Case Outline Y

.320 (8.13)

MAX

.310 (7.87)
.290 (7.37)

.013 (0.33)
.007 (0.18)

.020 (0.51)

MIN

.050 (1.27)
.035 (0.89)

.110 (2.79)
.090 (2.29)

SEATING PLANE

.390 (9.91)
.370 (9.41)

.020 (0.51)

MAX.

.055 (1.40)
.045 (1.14)

.170 (4.32)

MAX.

Case Outline Z

.390 (9.91)
.370 (9.41)

.140 (3.56)

MAX.

.045 (1.14)
.035 (0.89)

.020 (0.51)

MIN

.050 (1.27)
.035 (0.89)

.110 (2.79)
.090 (2.29)

SEATING PLANE

NOTES:

1. PIN 1 IS INDICATED BY THE ESD TRIANGLE MARKED ON THE LID OF THE PACKAGE.

2. DIMENSIONS ARE IN INCHES, (mm).

3. METRIC EQUIVALENTS ARE GIVEN FOR GENERAL INFORMATION ONLY.

4. UNLESS OTHERWISE SPECIFIED, TOLERANCE IS ±.005 (0.13mm).

Micropac Industries cannot assume any responsibility for any circuits shown or represent that they are free from patent infringement.

Micropac reserves the right to make changes at any time in order to improve design and to supply the best product possible.

MICROPAC INDUSTRIES, INC. MICROCS PRODUCTS DIVISION • 905 E. Walnut St., Garland, TX 75040 • [phone] • Fax [phone]

www.micropac.com

E-MAIL: [e-mail] 5/22/02

.320 (8.13)

MAX

.310 (7.87)
.290 (7.37)

.013 (0.33)
.007 (0.18)

Pg. 10 of 11

53111 Power MOSFET Optocoupler

ORDERING GUIDE

The followings are the cross-reference of Micropac part numbers versus Standard Military PIN. Please contact
Micropac for other desired options.

Micropac Part Number Standard Military Drawing PIN Case Outline

53111-1PA 5962-9314001HPA P

53111-1PC 5962-9314001HPC P

53111-1XA 5962-9314001HXA X

53111-1XC 5962-9314001HXC X

53111-1YA 5962-9314001HYA Y

53111-1YC 5962-9314001HYC Y

53111-1ZA 5962-9314001HZA Z

53111-1ZC 5962-9314001HZC Z

53111-2PA 5962-9314002HPA P

53111-2PC 5962-9314002HPC P

53111-2XA 5962-9314002HXA X

53111-2XC 5962-9314002HXC X

53111-2YA 5962-9314002HYA Y

53111-2YC 5962-9314002HYC Y

53111-2ZA 5962-9314002HZA Z

53111-2ZC 5962-9314002HZC Z

Micropac Industries cannot assume any responsibility for any circuits shown or represent that they are free from patent infringement.

Micropac reserves the right to make changes at any time in order to improve design and to supply the best product possible.

MICROPAC INDUSTRIES, INC. MICROCS PRODUCTS DIVISION • 905 E. Walnut St., Garland, TX 75040 • [phone] • Fax [phone]

www.micropac.com

E-MAIL: [e-mail] 5/22/02

Pg. 11 of 11