Dascom 1330 User Manual

Download

Page 1

Page 2

Tally Dascom 1330

Page 3

Tally Dascom 1330

Important Safety Instructions (English)

Read the following instructions thoroughly before starting up your printer.

 Never carry out maintenance or repair work yourself. Always contact a qualified service technician.

 Keep this Operator’s Manual in a place which is easily accessible at all times.

 Place the printer on a solid and even base so that it cannot fall.

 Never place the printer in the vicinity of inflammable gas or explosive substances.

 Ensure the printer is connected to a socket with the correct mains voltage.

 Always disconnect the printer from the mains before opening the device to perform maintenance work or

remedy errors.

 Do not expose the printer to high temperatures, direct sunlight or dust.

 Keep all liquids away from the printer.

 Protect the printer from shock, impact and vibration.

Make sure that the printer and computer are switched off before connecting the data cable.

 The Print Head will become very hot during printing; avoid contact with the Print Head after printing has

finished.

 Do not perform any operation or action in any way other than those provided in this manual. When in

doubt, contact your dealer or your customer support.

The device and mains-socket must all times be easily accessible.

Page 4

Tally Dascom 1330

Wichtige Sicherheitshinweise (German)

Lesen Sie bitte diese Sicherheitshinweise durch, bevor sie den Drucker in Betrieb nehmen.

 Führen Sie Wartungsarbeiten und Reparaturen keinesfalls selbst aus, sondern verständigen Sie immer

einen qualifizierten Servicetechniker.

 Bewahren Sie diese Dokumentation an einem jederzeit zugänglichen Ort auf.

 Den Drucker auf stabilem und ebenem Untergrund so aufstellen, dass er nicht zu Boden fallen kann.

 Stellen Sie den Drucker keinesfalls in der Nähe von leicht entzündlichen Gasen oder explosiven Stoffen

auf.

 Den Drucker nur an eine Steckdose mit der richtigen Spannung anschließen.

 Wenn Sie den Drucker vom Netz trennen wollen, den Drucker ausschalten und immer den Netzstecker an

der Steckdose ziehen.

 Den Drucker weder hohen Temperaturen noch direktem Sonnenlicht und Staub aussetzen.

 Keine Flüssigkeiten mit dem Drucker in Berührung bringen.

 Den Drucker keinen Erschütterungen, Stößen oder Vibrationen aussetzen.

 Sicherstellen, dass der Drucker und der Computer ausgeschaltet sind, bevor das Datenkabel

angeschlossen wird.

 Der Druckkopf wird während des Druckens heiß. Vor dem Berühren deshalb einige Zeit abkühlen lassen.

 Weichen Sie bei der Bedienung des Druckers nicht von den Anweisungen in der Dokumentation ab.

Bei Unklarheiten wenden Sie sich bitte an Ihren Händler oder Ihren Kundendienst.

 Maschinenlärminformations – Verordnung – 3.GPSGV, der höchste Schalldruckpegel beträgt 70 dB(A)

oder weniger gemäß EN ISO 7779.

Das Gerät und die Netzsteckdose müssen jeder Zeit leicht zugänglich sein.

Page 5

Tally Dascom 1330

III

Consignes importantes de sécurité (French)

Lire attentivement les instructions suivantes avant de mettre l’imprimante en service.

 Ne jamais effectuer soi-même les travaux d’entretien et de réparations. Contacter toujours un dépanneur

qualifié.

 Placer l’imprimante sur un support stable de façon à ce qu’elle ne puisse pas tomber.

 Ne jamais placer l’imprimante à proximité de sources de gaz aisément inflammables ou de substances

explosives.

 Ne connecter l’imprimante à une prise que lorsque la tension est correcte.

 Pour déconnecter l’imprimante de l’alimentation principale, mettre l’imprimante hors tension et toujours

débrancher le connecteur secteur de la prise murale.

 Ne pas exposer l’imprimante à des températures élevées, à la lumière directe du soleil ou à la poussière.

 Ne pas mettre l’imprimante en contact avec des liquides.

 Ne pas exposer l’imprimante à des chocs, impacts ou vibrations.

 S’assurer que l’imprimante et l’ordinateur sont hors tension avant de connecter le câble de données.

 La tête d’impression est brûlante pendant l’impression. C’est pourquoi laissez-la refroidir quelques

instants avant d’y toucher.

 N'exécutez aucune opération ni action d'une autre manière que celle indiquée dans ce manuel. En cas de

doute, veuillez contacter votre distributeur ou service après-vente.

Le dispositif et la prise principale doivent toujours être accessibles facilement.

Page 6

Tally Dascom 1330

Indicazioni di sicurezza importanti (Italian)

Prima di mettere in funzione la stampante, leggere attentamente le seguenti indicazioni.

 Non eseguire mai da sé gli interventi di manutenzione e riparazione, ma rivolgersi sempre a un tecnico di

assistenza qualificato.

 Conservare le presenti istruzioni per l’uso in un luogo sempre accessibile.

 Collocare la stampante su una superficie stabile, per evitare che cada a terra.

 Non collocare la stampante in prossimità di gas facilmente infiammabili o di sostanze esplosive.

 Collegare la stampante a una presa di corrente con tensione adeguata.

 Per scollegare la stampante dalla rete di alimentazione, spegnere la stampante e disinserire sempre il

connettore di rete dalla presa.

 Non esporre la stampante ad elevate temperature né alla luce solare diretta e alla polvere.

 Evitare il contatto della stampante con liquidi.

 Non esporre la stampante a colpi, scosse o vibrazioni.

 Verificare che la stampante e il computer siano spenti prima di collegare il cavo di trasmissione dati.

 Durante la stampa, la testina si surriscal-da notevolmente. Prima di toccarla, se necessario opportuno

quindi lasciarla raffreddare qualche istante.

 Non eseguire alcuna operazione o azione se non nella maniera descritta nel presente manuale. In caso di

dubbio, contattare il rivenditore o dalla società incaricata dell’assistenza.

Il dispositivo e la presa di corrente devono essere sempre facilmente accessibili.

Page 7

Tally Dascom 1330

Instrucciones de seguridad importantes (Spanish)

Lea las siguientes instrucciones con esmero antes de poner la impresora en servicio.

 Nunca lleve a cabo trabajos de mantenimiento o reparación Ud. mismo, sino consulte a un técnico de

servicio calificado.

 Guarde las presentes instrucciones de servicio en un lugar de fácil acceso en cualquier momento.

 Ponga la impresora sobre un base estable de manera que no pueda caer al suelo.

 Nunca coloque la impresora en la vecindad de gases de fácil inflamabilidad o sunstancias explosivas.

 Asegure conectar la impresora sólo a un enchufe con un voltaje correcto.

 Cuando quiera desconectar la impresora de la red, apague la impresora y siempre tire la clavija de

alimentación del enchufe.

 No exponga la impresora a temperaturas altas, a la luz solar directa y al polvo.

 No ponga la impresora en contacto con fluidos.

 Nunca exponga la impresora a sacudidas, choques o vibraciones.

 Asegúrese de que la impresora y el ordenador estén apagdos antes de conectar el cable de datos.

 La cabeza de impresión se pone muy caliente durante la impresión. Por lo tanto, deje enfriarlo algún

tiempo antes de tocarla.

 No permita que se realice cualquier operación o acción de una forma diferente a lo que se señala en el

manual. En caso de duda, póngase en contacto con su comerciante o con su servicio post-venta.

El dispositivo y la toma de corriente deben estar ubicados de forma que sea fácil acceder a ellos.

Page 8

Tally Dascom 1330

Правила по технике безопасности. (Russian)

Прочитайте, пожалуйста, инструкцию по технике безопасности перед включением в работу принтера.

 Не выполняйте технические работы и ремонт техники самостоятельно, но сообщайте о

неисправностях квалифицированным сервисным техникам.

 Данная инструкция должна быть всегда доступна каждому пользователю.

 Установите принтер на ровном и стабильном месте так, чтобы он не смог упасть на пол.

 Ни в коем случае не ставьте принтер вблизи легко воспламеняющихся газов и взрывчатых

веществ.

 Включайте принтер в розетку только с соответствующим напряжением.

 Если Вы хотите отключить принтер от напряжения, сначала выключите принтер сам и затем

выньте штекер из розетки.

 Берегите принтер от нагревания, от попадания на него прямых солнечных лучей и пыли.

 Не допускайте попадания жидкости на принтер.

 Нельзя подвергать принтер тряске, ударам и вибрации.

 Убедитесь, что принтер и компьютер выключены, только после этого соедините принтер с

компьютером.

 Печатающая головка нагревается во время работы принтера. Поэтому подождите какое-то время,

прежде чем дотронуться до нее.

 Пользуйтесь принтером так, как это написано в документации. Если у Вас возникают неясности,

обращайтесь с вопросами к Вашим продавцам или в сервисный центр.

Устройство и розетка должны быть всегда легко доступна.

Page 9

Tally Dascom 1330

VII

Instruções Importantes sobre Segurança (Portuguese)

Leia as instruções de segurança antes de usar a impressora.

 Consulte sempre um técnico qualificado para executar uma reparação.

 Coloque a impressora sobre uma base sólida e nivelada, para que ela não sofra quedas.

 Jamais instale a impressora nas proximidades de lugares onde haja gás inflamável ou substâncias

explosivas.

 Assegure-se de conectar a impressora à tomada elétrica com a voltagem apro-priada.

 Quando desligar a impressora da rede, desligue sempre a impressora e retire o cabo da tomada.

 Não exponha a impressora a temperaturas altas ou luz solar direta.

 Não aproxime substâncias líquidas da impressora.

 Proteja a impressora de choques, impactos e vibrações.

 Desligue a impressora e o computador antes de conectar o cabo da rede.

 A cabeça da impressora pode ficar muito quente .Portanto, espere algum tempo antes de tocá-la.

 Não faça nenhuma operação ou ação além das recomendadas neste manual. Em caso de dúvida,

contate seu revendedor ou companhia de serviço.

A impressora e a tomada devem ser facilmente em todos os momentos acessíveis.

Page 10

Tally Dascom 1330

VIII

Önemli Güvenlik Talimatları (Turkish)

Lütfen, yazıcıyı işletime geçirmeden önce bu güvenlik talimatlarını bütünüyle dikkatle okuyun.

 Bakım ve tamir çalışmalarını kesinlikle ve hiçbir surette kendi başınıza yapmayın; her zaman kalifiyebir

uzman servis-teknisyenine haber verin.

 Yazıcıyı, üzerinden yere düşmesi mümkün olmayacak sabit ve düz bir zemine yerleştirin.

 Yazıcıyı kesinlikle ve hiçbir surette kolayca yanabilecek gaz veya patlayıcı maddeler içeren nesnelerin

yakınına koymayın.

 Yazıcı akım kablosunu sadece doğru gerilime sahip bir prize takın.

 Yazıcıyı şebeke ağından ayırmak istediğinizde, yazıcıyı kapatın ve ağ-fişini her zaman prizden çıkartın.

 Yazıcıyı ne yüksek ısılı ne de doğrudan güneş ışığına ve toza mâruz kalan mekânlarda bulundurun.

 Yazıcı hiçbir sıvı maddeyle temasta olmamalıdır.

 Yazıcı hiçbir sarsıntıya, darbeye veya titreşime mâruz kalmamalıdır.

 Veri kablosu bağlanmadan önce hem yazıcının hem de bilgisayarın kapalıolduklarından emin olmalısınız.

 Yazıcının başı basma esnasında yüksek ısıya ulaşıyor. Bu yüzden lütfen dokunmadan önce kısa süre

soğumasını bekleyin.

 Yazıcının işletimi ve kullanımında bu dokümantasyondaki talimatların hiç dışına çıkmayın. Sorunlu

görünen hususlarda lütfen imâlatçınıza veya müşteri hizmetleri servisinize başvurun.

Cihaz ve elektrik prizinin her zaman kolayca erişilebilir olması gerekir.

Page 11

Tally Dascom 1330

TRADEMARK ACKNOWLEDGEMENTS

“IBM” is a trademark of International Business Machines Corporation.

“EPSON” is a trademark of Epson America Incorporated.

“DEC” is a trademark of Digital Equipment Corporation.

“Centronics” is a trademark of Centronics Data Computer Corporation.

“DOS” is a trademark of Microsoft Corporation.

“SAP” is a trademark of SAP AG.

“Windows”, “Windows 7”,”Windows 8”, “Windows 95”, “Windows 98“, “Windows NT”, “Windows 2000”, “Windows

2003/2008/2012 Server”, “Windows XP” and “Windows Vista” are trademarks of Microsoft Corporation.

All other product names and company names appearing in this manual are the registered trademarks or

trademarks of the individual companies.

Page 12

Tally Dascom 1330

Page 13

Tally Dascom 1330

TABLE OF CONTENTS

1 UNPACKING GUIDE ........................................................................................................................................ 1

1.1 Unpacking the Printer ................................................................................................................................. 1

1.2 Placing the Printer ...................................................................................................................................... 2

1.3 Printer Components ................................................................................................................................... 2

2 SETTING UP PRINTER .................................................................................................................................... 4

2.1 Install Ribbon .............................................................................................................................................. 4

2.2 Install the Sheet Feeder ............................................................................................................................. 6

2.3 Connecting the Interface Cable .................................................................................................................. 7

2.4 Connecting the Mains Power ..................................................................................................................... 7

2.5 Installing the Windows Driver ..................................................................................................................... 8

3 PAPER INSTALLATION ................................................................................................................................ 11

3.1 Adjusting Print Gap .................................................................................................................................. 11

3.2 Handling Cut Sheet .................................................................................................................................. 12

3.3 Handling Continuous Forms (Fanfold) ..................................................................................................... 13

3.4 Switching To Cut Sheet From Fanfold ..................................................................................................... 14

3.5 Switching To Fanfold From Cut Sheet ..................................................................................................... 14

3.6 Setting Fanfold Relative To Printer .......................................................................................................... 14

4 CONTROL PANEL OPERATION ................................................................................................................... 16

4.1 Keys and LEDs ......................................................................................................................................... 16

4.2 Panel Operations ...................................................................................................................................... 17

4.3 Online State .............................................................................................................................................. 18

4.4 Offline State .............................................................................................................................................. 19

4.5 Common Settings ..................................................................................................................................... 21

4.6 Power-On State ........................................................................................................................................ 23

4.7 Slip --- Printing on and Settings for Customized Form ............................................................................. 24

4.7.1 Slip Setup .......................................................................................................................................... 24

4.7.2 Activation and Deactivation of Slip-profile ......................................................................................... 26

5 PRINTER SETTING CHANGES ..................................................................................................................... 27

5.1 System Setup ........................................................................................................................................... 28

5.2 Paper Setup ............................................................................................................................................. 30

5.3 Interface Setup ......................................................................................................................................... 33

5.4 Character Setup ....................................................................................................................................... 34

5.5 Other Setup .............................................................................................................................................. 35

5.5.1 German (Deutsch) ............................................................................................................................. 36

5.5.2 Russian (Россия) .............................................................................................................................. 39

5.5.3 Italian (Italiano) .................................................................................................................................. 42

5.5.4 French (Français) .............................................................................................................................. 45

Page 14

Tally Dascom 1330

5.5.5 Spanish (Español) ............................................................................................................................. 48

5.5.6 Turkish (Türkce) ................................................................................................................................ 50

5.6 Black Mark Parameters ............................................................................................................................ 53

5.7 Bi-directional Alignment............................................................................................................................ 55

5.8 Restore Factory Default ........................................................................................................................... 56

5.9 Tally Dascom Printer Config Tool ............................................................................................................ 57

6 CUSTOMIZED FORM ..................................................................................................................................... 58

6.1 Customize Cut Sheet Form Length .......................................................................................................... 58

6.2 Customize Cut Sheet TOF ....................................................................................................................... 60

6.3 Customize Cut Sheet Bottom Margin ....................................................................................................... 61

6.4 Customize Cut Sheet Left Margin ............................................................................................................ 61

6.5 Customize Fanfold Page Formatting Parameters .................................................................................... 61

7 MAINTENANCE .............................................................................................................................................. 62

7.1 Cleaning ................................................................................................................................................... 62

7.2 Cleaning and Vacuuming the Printer ....................................................................................................... 62

7.3 Cleaning the Paper Rollers ...................................................................................................................... 63

8 TROUBLESHOOTING .................................................................................................................................... 64

8.1 Print Quality Problems and Solutions ....................................................................................................... 64

8.2 Paper Handling Problems and Solutions ................................................................................................. 65

8.3 Operating Problems and Solutions .......................................................................................................... 66

8.4 Printer Failures ......................................................................................................................................... 66

8.5 Error Indications on LEDs ........................................................................................................................ 67

8.6 Diagnostic Functions ................................................................................................................................ 67

8.7 Firmware Update ...................................................................................................................................... 67

9 GENERAL SPECIFICATIONS ....................................................................................................................... 70

10 INTERFACE .................................................................................................................................................. 73

10.1 Parallel Interface .................................................................................................................................... 73

10.2 USB Interface ......................................................................................................................................... 74

10.3 Serial interface ....................................................................................................................................... 74

11 CODE PAGES .............................................................................................................................................. 76

11.1 Character Set ......................................................................................................................................... 76

11.2 Code Page Commands .......................................................................................................................... 81

11.3 Code Page Tables.................................................................................................................................. 82

12 COMMAND SETS ....................................................................................................................................... 112

12.1 Epson ESC/P2 emulation command list .............................................................................................. 112

12.2 IBM emulation control codes ................................................................................................................ 114

FCC STATEMENT ........................................................................................................................................... 117

Page 15

Tally Dascom 1330

III

Symbols used Important information is highlighted in this manual by two symbols.

CAUTION highlights information which must be observed in order to prevent injuries to user and damage to the printer.

NOTE highlights general or additional information about a specific topic.

Page 16

Tally Dascom 1330

1 Unpacking Guide

1.1 Unpacking the Printer

1. Place your packaged printer on a solid base.

2. Make sure that the “Up” symbols point in the correct direction.

3. Open the packaging, lift the printer out of the cardboard box and remove the remaining packaging material.

4. Check the printer for any visible transport damage and missing items. If you find any transport damage or if any accessories are missing, please contact your dealer. The following items should be included:

o Printer o Paper Feed Knob o Sheet Feeder o Power Cord o Ribbon Cartridge o CD-ROM o Installation Guide o USB cable

Remove the packaging materials from the printer as follows:

1. Open the Front Flap of the printer.

2. Remove the shipping cardboard protecting the Print Head.

3. Install the Paper Feed Knob.

Page 17

Tally Dascom 1330

1.2 Placing the Printer

Place the printer on a solid, flat, and stable surface. Clear the spaces around the printer for ventilation, accessing the control panel, installing the paper, and collecting the print out.

When selecting the printer location, observe the following additional instructions:

1. Never place the printer near to any flammable gas or explosive substances.

2. Do not expose the printer to direct sunlight. If you cannot avoid placing the printer near a window, protect it from the sunlight with a curtain.

3. When connecting a computer to the printer, make sure the maximum recommended cable length is not exceeded.

4. Ensure sufficient distance between the printer and any heating devices/radiators.

5. Avoid exposing the printer to extreme temperature or air humidity fluctuations. Avoid exposure to dusty environments.

6. It is recommended the printer is installed in a position which reduces noise exposure to the work place during printing.

7. The socket-outlet shall be installed near the equipment and shall be easily accessible.

1.3 Printer Components

Page 18

Tally Dascom 1330

Component

Function

Front Flap

Protects the Print Head and other parts inside, and reduces noise.

Paper Guides

Adjusts the position of a cut sheet.

Sheet Feeder

Supports the cut sheet so as to ensure the paper in and out easily.

Paper Holder

Extended support for large size cut sheets.

Print Head

24-pin printing mechanism.

Head Gap Lever

Adjusts the gap between the Print Head and various form thickness.

Control Panel

Shows printer status, for printer setup.

Paper Feed Lever

Two positions: =continuous forms; = single sheet paper

Paper Feed Knob

Manual adjusts the vertical position of the paper.

Power Switch

Powers the printer ON or OFF.

Ribbon Cartridge

Holds inked Ribbon in it.

Ribbon Guide

Guides Ribbon installation on the Print Head.

Tractors

For feeding and adjustment of continuous forms.

Power Cord

Connects the printer and power socket.

Interface

Connects interface cable from the host.

Page 19

Tally Dascom 1330

2 Setting Up Printer

2.1 Install Ribbon

Switch printer off during Ribbon installation.

1. Open the Front Flap as shown in below picture.

2. Raise the Head Gap Lever to the top most position, labeled “ ”.

3. Pull the Upper Friction Frame ① and then lock it ② in place to the side plates.

Page 20

Tally Dascom 1330

4. Carefully move the Print Head to the center.

5. Tilt the Ribbon Cartridge a bit and match it to the positions ① and ② on both ends.

6. Then slightly press it down to hold it in place to the mentioned positions.

7. Hold the Ribbon Guide ① on the Ribbon Cartridge. Guide ② it onto the Print Head. Then turn the Ribbon Knob in clockwise direction until the ribbon fabric is taut. Move the carriage left and right to make sure the ribbon fabric is taut.

8. Release the front of Upper Friction Frame to its original position.

Page 21

Tally Dascom 1330

9. Lower the Head Gap Lever to the right scale according to the paper thickness.

10. Close the Front Flap to reduce printing noise and prevent dust going into the printer.

Open it only for ribbon installation and adjustment.

Notes on Ribbon Cartridge Removal:

1) Clear the paper in the printer.

2) Turn off the printer power.

3) Set the Gap Lever to the top most position, labeled “ ”.

4) Open the Front Falp.

5) Let the Print Head cool down, if necessary. Move the carriage to the middle.

6) Pull out the blue Ribbon Guide from the Print Head.

7) Hold the handle bar on the Ribbon Cartridge and pull the cartridge towards you to unlatch it. Some force may be needed to unlatch the cartridge.

8) Remove the ribbon fabric from the Print Head carefully without entangling it.

2.2 Install the Sheet Feeder

As shown in the picture, ensure the Sheet Feeder fingers fit into the slots of the printer. Push in the Sheet Feeder until its sides latch on the fixed bolts in the printer. The Sheet Feeder is now installed successfully.

To remove the Sheet Feeder, use one hand to hold the printer and the other hand to pull and unlatch the Sheet Feeder.

Page 22

Tally Dascom 1330

2.3 Connecting the Interface Cable

The 36-pin Centronics parallel and USB ports locate at the rear of the printer. IMPORTANT: Switch off the printer and the computer before connecting or disconnecting the interface cable to prevent electrical damage to the interface ports.

2.4 Connecting the Mains Power

Make sure that the device has been set according to your country’s power supply voltage. To do this, check the rating plate at the back of the printer. Contact your dealer if the setting is incorrect.

Never switch on the printer if the voltage setting is incorrect; this may result in electrical damage to the printer.

Make sure that the power switch “A”, located to the right side of the printer, is in the “O” (Off) position.

Page 23

Tally Dascom 1330

2.5 Installing the Windows Driver

(Windows 2000 / XP / Vista / 7 / 8 / 8.1 and 2003 / 2008 / 2012 / 2012R2 Server)

1. Your printer CDROM comes with Windows drivers. Go to the Drivers folder and run the Installer “Tally Dascom Printer Config Tool Setup.msi”. You will see the follow screen.Click “Next” to continue.

Connect the Power Cord to the power inlet of the printer. Connect the Power Cord plug to a mains socket. Switch on the printer.

Page 24

Tally Dascom 1330

2. Input the folder containing the driver.

3. Click “Next” to confirm installation.

4. The screen shows the installation in progress.

Page 25

Tally Dascom 1330

5. The screen shows successful installation.

Page 26

Tally Dascom 1330

3 Paper Installation

The printer can handle either single sheets or continuous forms. Single sheets, also called cut sheets, include envelopes or non-continuous (single or multipart) forms. Continuous forms include labels and multipart forms fed into the printer using the stationery tractors. The printer is capable of printing up to original + 6-ply multipart paper.

To ensure the print quality and protect the Print Head, set a proper print gap by the gap lever (see 3.1) for the form thickness and do not load folded, damaged, wrinkled, or curled paper.

3.1 Adjusting Print Gap

Sliding the Head Gap Lever on the right side up and down can increase and reduce, respectively, the print gap to support various form thickness.

Paper type

Weight (g/m2) / ply

Thickness (mm)

Gap lever position

1~2 plies

52～100

0.06～0.16

3~4 plies

40～55

0.17～0.24

4~5 plies

40～55

0.25～0.30

5~6 plies

40～55

0.31～0.36

6~7 plies

40～55

0.37～0.42

Over 7 plies

40～55

0.43～0.48

Thick paper

——

0.49～1.0

/ /

Change

ribbon

——

The “ ” position is only for unloading or installing the ribbon. When the lever is set higher than appropriate, it will result in poor print. Improper head gap setting shortens the ribbon and head life.

Setting a wrong print gap may cause print head damage and shorten the head life.

Page 27

Tally Dascom 1330

3.2 Handling Cut Sheet

The front friction path supports the printing on single- or multi-ply cut sheets loaded manually. Use the rear tractors for continuous forms.

1. Select the eject direction to the front or to the rear through the Printer Setting/Menu.

2. Slide the Paper Guide to set an appropriate left margin

Loading Cut Sheet

1. Turn off the power.

2. Slide the Paper Guide to set the desired left margin.

3. Turn on the power.【The Power/Paper out LED】blinks to indicate out of paper status.

4. Slide the Paper Feed Lever to the position.

5. Manually insert a piece of cut sheet into the slot above the Sheet Feeder. The printer then loads the paper to its TOF position (the first print position) and lights up the Online LED, indicating the ready state.

Page 28

Tally Dascom 1330

3.3 Handling Continuous Forms (Fanfold)

The printer can handle continuous form of width up to 10 inches, loaded by the rear Tractors as shown in the diagram.

Loading Continuous Form

1. Turn off the power.

2. Keep a stack of fanfold at a height below the Tractors.

3. Slide the Paper Feed Lever to the position.

4. To set the desired left margin and form width, disengage the Tractor Locks to allow free movement of the Tractors.

5. When the left margin is set, tighten the Left Lock (viewed from rear). Raise the Tractor Doors and fit the first 3 paper holes onto the Left Tractor Pins. Close the Left Tractor Door. In the same way, install the paper on the right tractor. Ensure the paper is flat and smooth before tightening the Right Tractor Lock.

6. Double check if the paper holes properly fit in the Tractor Pins. Improper installation may cause paper jam and damage the printer.

7. Turn on the power. The【Power/Paper out】LED blinks to indicate out of paper status.

8. Press the【Load/Eject】key to load the paper to its TOF position. The【Online】LED lights up to indicate the ready state.

Page 29

Tally Dascom 1330

3.4 Switching To Cut Sheet From Fanfold

1. When the printer is offline (see Chapter 4), press the【Load/Eject】key to clear the fanfold out of the Platen to allow cut sheet operation.

2. Follow the below procedures to change to cut sheet operation from tractor mode:

 If the printer is online, press the【Load/Eject】key to feed the fanfold to its tear-off

position. Tear off the page.

 Press the【Online】key once to set the printer offline. Press the【Load/Eject】key to

withdraw the fanfold out of the Platen.

 Slide the Paper Feed Lever to the position. Then follow the procedures in Section

3.2 for cut sheet operation.

The printer will signal an alarm if you change the Paper Feed Lever position while paper still remains in the printer.

3.5 Switching To Fanfold From Cut Sheet

To re-load the parked continuous form:

1. Clear the cut sheet from the Sheet Feeder by pressing Exit key.

2. Slide the Paper Feed Lever to the position.

3. Set the printer to offline. Press the【Load/Eject 】key to re-load the parked fanfold.

3.6 Setting Fanfold Relative To Printer

1. It is recommended to place the printer 75 cm above the floor.

2. Keep the stack of fanfold less than 3 cm side ways off from the printer.

Page 30

Tally Dascom 1330

3. The printer should sit on a pedestal or a table without blocking the paper feeding and stacking. Keep the printer more than 60 cm away from the back wall.

1) Never place the printer next to any flammable gas or explosive substances.

2) Do not expose the printer to direct sunlight.

3) The interface cable should not exceed the recommended length,see

specification.

4) Ensure sufficient distance between the printer and any heating

devices/radiators.

Page 31

Tally Dascom 1330

4 Control Panel Operation

General functions for the keys are clearly designated on the Panel label. Some other special settings need pressing multiple keys simultaneously or holding some keys when powering on the printer. This Chapter will describe the functions of the keys and display on the Panel.

4.1 Keys and LEDs

There are 4 keys on the Control Panel, from left to right:【Load/Eject】, 【TOF】, 【LF/FF】, and【Online】 keys. Meanwhile, there are 4 LEDs, from left to right:【Power/Paper out】,

【Front Exit】,【Speed】, and【Online 】LEDs. The Control Panel is shown as below:

Below describes the function of each key/indicator: Indicators

1.【Power/Paper out】On when the printer is powered on; Off when the printer is switched off; Blinking when out of paper.

2.【Front Exit】On to indicate cut sheet exit at the front after printing; Off to indicate cut sheet exit at the rear.

3.【Speed】On, Off, or Blinking when the test print quality is NLQ, LQ or Draft respectively.

4.【Online】On when the printer is active to receive and print data from the host; Off when it is offline.

Keys

1. 【Load/Eject】

This key either loads a paper from the active source or clears the paper out of the Platen.

1) Cut sheet: Only when Single Auto Loading is disabled in Paper Setup (see section 5.3), you have to press this key to load a cut sheet. By default, a cut sheet comes out from the front.

Page 32

Tally Dascom 1330

2) Tractor mode: Only when Fanfold Auto Loading is “No” in Paper Setup (see section 5.3), you have to press key to load a fresh continuous form. When paper exists on the Platen, this key may have two effects:

 It clears the continuous form out of the Platen and keeps it in the tractors.  It reverses the continuous form to its TOF position if it is originally at the tear-off

position.

2. 【TOF】 Holding down this key starts to reverse the paper at Mirco Feed mode. Release the key to stop the reverse action.

3. 【FF/LF】 When the printer is online or offline, a press on this key moves the paper forward by one line. If in tractor mode, holding this key will start with a few lines fed and then perform a form feed. If the fanfold is currently at the tear-off position, pressing this key will reverse the paper to its TOF position.

4. 【Online】

1) The printer can be set online or offline by this key. When the printer is at online state, press this key one time to switch the printer to offline; meanwhile, the【Online】LED is off. Press this key again to switch the printer back to online again, and the【Online】LED is on.

2) Out of paper, indicated by blinking 【Power/Paper out】LED, causes the printer offline. Re-loading the paper, the printer automatically goes online with the

【Power/Paper out】LED on. If the loaded paper is at the tear-off position, pressing

this key again will reverse the paper to its TOF position.

4.2 Panel Operations

The same key is assigned with different functions depending on the states of operation, namely: Online, Offline, Common Settings, and Power-On.

1. Online: The【Online】LED lights up to indicate the printer is online, which is the normal operation state for printing. A press on the【Online】key toggles the printer between Online and Offline states.

2. Offline: The【Online】LED turns off to indicate the printer is offline, a state that the printer pauses to receive data from the host computer.

3. Common Settings: The panel operations described in Section 4.5 is valid in both the online or offline states.

4. Power-On: To enter the Power On state, the user holds down a key or a combination of keys while powering up the printer.

Page 33

Tally Dascom 1330

4.3 Online State

Sections 4.3 to 4.7 describe the panel operations in details with the following legends: [A] = press and hold key A

{B} = press and then release key B

[A] + {B} = press key B while holding A

[A] {B} = hold then release key A; next a press on key B

Function Name

Key

LED

Function Description

Eject cut sheet

Tear-off fanfold

{S1}

 Cut sheet mode:

Clears the cut sheet from the Platen in the direction specified by the Exit Direction setting in Section 5.3.

 Tractor mode:

Feeds the form to its tear-off position. A new print job or pressing this key again to move the fanfold to the next TOF position.

Note: Please refer to the Tear setting in Section 5.3 for Auto and Manual Tear-off.

Eject Direction

(cut sheet only)

[S1] +

{S2}

L2 = ON:

Out to

front

By pressing the【TOF】key while holding the

【Load/Eject】key can toggle the eject direction

for cut sheets. The【Front Exit】lights up to indicate cut sheets

ejected to the front.

NOTE: Section 4.5 lists out additional operations while the printer is online

Page 34

Tally Dascom 1330

4.4 Offline State

Function

Name

Key

LED

Function Description

Load/Eject

{S1}

 Load: Automatically loads the paper from the

active source when no paper is on the Platen.

 Eject: Clears the paper completely out of the

platen. In tractor mode, the continuous form still remains in the tractors.

Clear Buffer

Initialize Printer

[S4] + {S2} + {S3}

[S4] + {S2} + {S3} for longer time

Unprocessed data remaining in the printer buffer may corrupt the subsequent print result. The procedures to clear the printer buffer:

 Clear all print jobs to the printer from the host

computer.

 Press the 【Online】 key to set the printer

offline. The printing stops but unprocessed data still remain in the print buffer.

 Simultaneously press the 【LF】 and【TOF】

keys while keep holding the【Online】key. A second later, the printer beeps once to indicate clearing the print buffer.

 If hold the process for a few more seconds, the

printer beeps 3 times to indicate the printer is initialized to its power up settings.

Page 35

Tally Dascom 1330

Function

Name

Key

LED

Function Description

Override Multi Paper

[S1] → {S3} Hold [S1] for

2 sec.

Power

(L1)

Speed

(L3)

This function overrides the Multi Paper setting in Section 5.3. The setting procedures:

 Hold the 【Load/Eject】key for 2 seconds

while the printer is offline and paper is loaded. The【Power/Paper Out】LED starts blinking.

 Every press on the【LF】key rotates the Multi

paper settings between Disable (L3 = off), Standard (L3 = on), and Enhance (L3 = blinking).

 Finally, press the【Load/Eject】key to save the

setting and terminate the procedures with the paper ejected. The 【Power】LED starts flashing.

Activate Slip Profile

[S1] → {S4} Hold [S1] for 2 sec.

Power

Online

This function conveniently recalls the top and left margins profile to facilitate slip/voucher printing. (Read Section 4.7 for details.)

The procedures to activate and deactivate Slip profile:

 Hold the 【Load/Eject】key for 2 seconds

while the printer is offline and paper is loaded. The【Power】LED blinks.

 Alternative presses on the 【Online】key

activate and deactivate the Slip profile. Accordingly, the 【Online】 LED blinks and lights up to indicate the activation and deactivation, respectively.

 Finally, press the【Load/Eject】key to save the

setting and terminate the procedures with the paper ejected. The【Power】LED stops blinking.

Micro-adjust TOF

[S4] → {S1} Hold [S4] for

3 sec.

Online

 Hold the 【Online】key for 3 seconds while the

printer is offline and paper is loaded. The

【Online】LED starts blinking.

 Press the【TOF】 or 【LF】keys to adjust the

TOF position precisely.

 Finally, press the【Online】key to save the

setting and terminate the procedures. The

【Online】LED stop blinking.

NOTE: Section 4.5 lists out additional operations while the printer is offline

Page 36

Tally Dascom 1330

4.5 Common Settings

This table lists out the panel operations valid in both the Online and Offline states.

Function

Name

Key

LED

Function Description

Micro

Reverse

{S2}/[S2]

In combination with the【LF】key, this function can fine-tune the top margin on the current page without affecting theTOF position on subsequent pages.

 Press the【TOF】key while holding down the

【Online】key.

The printer feeds the paper in the reverse direction with tiny steps to allow fine tuning of the top margin. Release the key(s) to terminate the adjustment.

NOTE: For fanfold, avoid reversing the paper over the previous page. Over-reversing may cause paper jam.

[S4] + {S2}

Micro

Forward

[S4] + {S3}

While holding down the【Online】key, press the

【LF】key to micro feed paper in the forward

direction.

Line Feed

{S3}

Feeds a line with every press on the【LF】key.

Page 37

Tally Dascom 1330

Function

Name

Key

LED

Function Description

Form Feed

[S3]

In tractor mode, holding this key will initially feeds a few lines; then afterward feeds the paper to the next TOF. If the paper is initially at the tear-off position, holding this key causes the current page returning to its TOF position.

For cut sheet, Form Feed function is invalid. In cut sheet mode, holding this key will keep line feed until paper out.

Print Speed

[S1] + {S3}

Speed

Pressing the【LF】key while holding the

【Load/Eject】key changes the print speed

between LQ (L3 LED off), NLQ (L3 LED on), and Draft (L3 LED flashing).

Carriage

Return

[S1 ] + {S4}

Pressing the【Online】key while holding the

【Load/Eject】key initializes the carriage to

recover from carriage fault (Error Alarm) caused by the code stripe. The printer then resumes the printing at the code strip position.

This function cannot recover the carriage faults caused by ribbon jam or other reasons.

Online

{S4}

Online

Toggles between online and offline states.

Page 38

Tally Dascom 1330

4.6 Power-On State

While powering up the printer, hold the key(s) listed in the below chart.

Function

Name

Key

LED

Function Description

Parameters

setting

[S1]

Users can customize specific setting(s) to meet application requirements. New settings are effective permanently until the next change or Restore Factory Defaults. See Chapter 5 for details.

Slip

[S2]

Configures the Slip layout profile such as top and left margins. Refer Section 4.7 for details.

Hex Dump

[S3]

Speed

The printer beeps once and the【Speed】LED blinks to indicate Hex Dump mode, in which the printer prints data from the host line by line in hexadecimal representation then 16 ASCII codes leading by a line number.

When the printer printing data, press【Online】 key to pause printing. Turn the power off and the printer exits the Hex Dump mode.

Self Test /

Status Page

[S4]

Prints the version numbers, settings and self-test pattern.

Recommend to load 10-inch fanfold before the operation.

Page 39

Tally Dascom 1330

Function

Name

Key

LED

Function Description

Restore

Factory

Defaults

[S4] + [S3]

Restore all settings to factory defaults. The carriage initializes and the printer beeps

once after restoration.

Customize

Page Layout

[S4] + [S2]

To customize the margins and tear-off position, please refer Chapter 6 for details.

Firmware

Update

[S1] + [S2] +

[S3 ] + [S4]

All

Alternate blinking of【Speed】and【Online】LED indicates ready for firmware update from host.

 Update process:

Execute the Configuration Tool on your PC. Then upload the update firmware to the printer. During the update process by both methods,

【Speed】and【Online】LEDs blink

alternatively while【Power】and【Front Exit】 LEDs are constantly on.

 Completion:

At completion, the carriage initializes and the

【Power】LED blinks with the 【Front Exit】

LED constantly on.

It takes ~20 seconds to complete the whole process. The printer resets after completion. If an error occurs repeat the process.

NOTE: Ensure not to turn off the power or unplug the interface cable during the whole process. Only trained operators should do this update; otherwise, incorrect operation may easily damage the printer.

4.7 Slip --- Printing on and Settings for Customized Form

Printing on a slip/voucher usually requires unique top and/or left margins, namely the “slipprofile”. The Control Panel operation supports convenient storing and recalling the slip-profile, as well as activating and deactivating it.

4.7.1 Slip Setup

This printer uses question and answer sessions to setup parameters here and in Chapter 5. The printer prompts a message or a parameter name. Then follows a line of assignments of keys for which the user replies to the prompted message or changes the value of the parameter.

To configure the top and left margins for slip (slip-profile), please do the followings:

1. Power up printer while pressing the 【TOF】 key until the Print Head starts moving, then let go.

Page 40

Tally Dascom 1330

2. Load Paper. The printer prints the few lines below:

Paper Slip Mode

[LF]=Next, [TOP]=Back, [LOAD/EJECT]=OK, [ONLINE]=Exit, [ONLINE]+[LOAD/EJECT]= Save and restart the printer.

Single Top Margin

Press the Next or Back keys to scroll to the parameter you want to change. The changeable parameters in the Slip-profiles are: Single Top Margin, Single Left Margin, Fanfold Top Margin, and Fanfold Left Margin in this order if Next is pressed. Pressing Back lists the parameter names in the reverse order.

1) Setting Single Top Margin:

 When Single Top Margin is prompted, press OK to go into this designated setting

and the printer prompts:

[Single Top Margin] [TOP]=-1，[LF]=+1，[LOAD/EJECT]=OK，[ONLINE]=Back，[ONLINE]+[LOAD/EJECT]=Save and restart the printer. (Unit：mm) 4

 “4” in the last line shows the current top margin = 4mm. Enter the new value by

pressing -1 or +1. The allowed range for top margin is -25 ~ 128 mm.

 Press OK to let the printer prompt the revised value. Press Save and restart if you

do not intend to change other slip-profile parameters. Otherwise, press OK again to confirm the change and the printer prints an “*” following the revised value. Then the printer prompts a message to ask to save the revised value:

Save the parameter settings ([LOAD/EJECT] or [ONLINE] = OK, [LF] = Next)? Yes

 Press OK to confirm saving and the printer prompts an “*” following the “Yes” to

respond to your confirmation. Otherwise, press Next to give up the change; the printer prompts a “No” and expects you to press OK to confirm not to save.

2) Setting Single Left Margin:

 In the Step 2 prompt, press Next to skip to the Single Left Margin setting indicated

by this prompt:

Single Left Margin

 Follow the same procedures in 2-1) to revise the left margin. The allowed range of

left margin is -77 ~ 77 mm.

3) Apply similar procedures to configure the top and left margins parameters for fanfold.

Keys act as proxies for designated functions in the setting dialog.

Page 41

Tally Dascom 1330

4.7.2 Activation and Deactivation of Slip-profile

1. Activate the Slip-profile:

1) Hold the【Load/Eject】key for 2 seconds while the printer is offline and paper is loaded. When the【Load/Eject】key is released, the printer beeps once and the

【Power】LED blinks.

2) Next press the【Online】key (the【Online】LED blinks) to recall the profile of top and left margins for subsequent print jobs. Finally press the【Load/Eject】key and the printer beeps once to activate the Slip-profile

2. Deactivate the Slip-profile:

1) Hold the【Load/Eject】key for 2 seconds while the printer is offline and paper is loaded. When the【Load/Eject】 key is released, the printer beeps once and the

【Power】LED blinks.

2) Next press the【Online】key (the【Online】LED is on) to deactivate the profile of top and left margins for subsequent print jobs. Finally press the【Load/Eject】key and the printer beeps once.

Page 42

Tally Dascom 1330

5 Printer Setting Changes

New settings in this chapter are permanently effective until the next change.

In order to meet specific print requirements, the printer configurations may be changed as follows: Hold down the【Load/Eject】key while powering on the printer and then release the key when the Print Head starts to move. After loading paper, the printer prompts the Printer Settings menu:

Printer Settings

[LF]=Next, [TOP]=Back, [LOAD/EJECT]=OK, [ONLINE]=Exit, [ONLINE]+[LOAD/EJECT]= Save and restart the printer.

System Setup

Follow the printed dialog to input corresponding keys to skip a sub-menu, to change parameter

values, or to save the changes. (Also see section 4.7.1.)

The Printer Settings menu contains 8 sub-menus appearing in the following order when Next skips a sub-menu (refer to [LF] assignment in the above prompt):

 System Setup  Paper Setup  Interface Setup  Character Setup  Other Setup  Bi-directional Alignment  Black Mark Mode  Restore Factory Defaults

When you reach the desired sub-menu containing the parameter(s) to be changed, press OK to go into the sub-menu to make change(s). The remaining procedures are similar to the ones described in section 4.7.1.

Keys act as proxies for designated functions in the setting dialog.

Page 43

Tally Dascom 1330

5.1 System Setup

NOTE: The fat printed words are default.

System setup

Valid Settings

Function

Language

English,Deutsch,Poccия, Italiano,Français,Español, Türkçe,Portuguese.

Allows user to select one of the following languages: English, German, Russian, Italian, French, Spanish and Turkish, Portuguese.

Emulation

ESC/P2, IBM

Selects the printer emulation. This should be the same as the host printer driver.

Auto CR (ESC/P2)

No, Yes

Yes: LF = LF+CR; No: LF = LF (Applies to ESC/P2 emulation only)

Auto CR(IBM)

No, Yes

Yes: LF = LF+CR; No: LF = LF (Applies to IBM emulation only)

Auto LF

No, Yes

Yes: CR = CR+LF; No: CR = CR

Print Dir

Bi-Dir, Uni-Dir

Bi-Dir: Graphics and text are printed in both directions, resulting in faster printing speed.

Uni-Dir: Graphics and text are printed from left to right, resulting in higher precision.

Form Line

Disable,Enabled,Dashed, NoPrint

Disable: Grids in block graphics are disjoint, but grids by graphics commands or slanted grids (block graphics) are not affected.

Enabled: Vertical grids are continuous in all line spacing.

Dashed: Horizontal grids are printed in dotted lines and vertical grids are not affected.

NoPrint: Grids are not printed. But nested grids (by graphical commands) above 2 levels deep are printed.

Zero

0, Ø

0: No-slashed Zero 0. Ø: Slashed Zero Ø.

Text Quality Mode

LQ, NLQ, Draft

Selects different text print quality.

Change Pin#1:

No, 1, 2, 3, 4, 5, 6, 7, 8, 9, 10, 11, 12, 13, 14, 15, 16, 17, 18, 19, 20, 21, 22, 23, 24

Defines the first broken / worn out pin. This pin will be substituted by an adjacent pin in the second pass printing.

No: No substitution.

Page 44

Tally Dascom 1330

System setup

Valid Settings

Function

Change Pin #2

No, 1, 2, 3, 4, 5, 6, 7, 8, 9, 10, 11, 12, 13, 14, 15, 16, 17, 18, 19, 20, 21, 22, 23, 24

Defines the first broken / worn out pin. This pin will be substituted by an adjacent pin in the second pass printing.

No: Not to substitution of the worn out pin.

Paper Slip Mode

No, Yes

See section 4.7 Slip. Yes: The printer takes the top and left

margin settings according to the Slip Profile.

No: The printer takes standard top and left margins settings.

Power-Saving

OFF, 1min, 2min, 5min, 10min

Defines the idle period before the printer gets into Save-energy Mode.

OFF: The printer never goes into Save-energy Mode.

Multipaper

Disable, Standard, Enhance

Disable: The printer ignores the determination of paper thickness sensor; it keeps the impact force and the print speed unchanged.

Standard: The printer increases the impact force and reduces the print speed.

Enhance: The printer prints with even stronger impact force and slower print speed.

Impact

Normal, Heavy

Normal: The print speed is faster causing head hot easily and the impact force is weaker.

Heavy: The print speed is reduced, resulting better thermal performance and copy capability.

Graphic Speed

Normal, Fast, Ultra

Selects different graphic print speed.

Page 45

Tally Dascom 1330

5.2 Paper Setup

Paper Setup

Valid Settings

Function

Single FormLen

2.5, 11/4, 3, 3.5, 11/3, 4, 5,

5.5, 6, 7, 8, 9, 10, 11, 12, 14, A4, B4, Customize

Sets the page length for single paper

Single Top

0, 1/6, 1/4, 1/3, 1/2, 2/3, 3/4, 1, Define

Defines the separation in inches from the top edge of a single paper to the first print line.

Single Bottom

0, 1/6, 1/4, 1/3, 1/2, 2/3, 3/4, 1, Define

Defines the separation in inches from the bottom edge of a single paper to the last print line.

Single Left Mrg (1.00mm)

-7, -6, -5, -4, -3, -2, -1, 0, 1, 2, 3, 4, 5, 6, 7, Define

Compensation value added to Single Left Mrg.

Single Top Mrg (0.01”)

-7, -6, -5, -4, -3, -2, -1, 0, 1, 2, 3, 4, 5, 6, 7

Compensation value added to Single Top.

Single Auto Load

Disable, 0.5sec, 1sec,

1.5sec, 2sec

Defines the settling time before a single sheet is loaded.

Disable: Press the【Load/Eject】key manually to load a single sheet.

Fanfold FormLen

2.5, 11/4, 3, 3.5, 11/3, 4, 5,

5.5, 6, 7, 8, 9, 10, 11, 12, 14, A4, B4, Define

Sets the Page Length for fanfold.

Fanfold Top

0, 1/6, 1/4, 1/3, 1/2, 2/3, 3/4, 1, Define

Defines the separation in inches from the top edge of a fanfold to the first print line.

Fanfold Bottom

0, 1/6, 1/4, 1/3, 1/2, 2/3, 3/4, 1, Define

Define the separation in inches from the bottom edge of a fanfold to the last print line.

Fanfold Left Mrg (1.00mm)

-7, -6, -5, -4, -3, -2, -1, 0, 1, 2, 3, 4, 5, 6, 7, Define

Compensation value added to Fanfold Left Mrg.

Fanfold Top Mrg (0.01”)

-7, -6, -5, -4, -3, -2, -1, 0, 1, 2, 3, 4, 5, 6, 7

Compensation value added to Fanfold Top.

Fanfold Auto Load

No, Yes

Yes: The printer loads paper to the first printing position automatically when using fanfold.

No: Press the【Load/Eject】key to load paper when using fanfold.

Skip

No, Yes

Skips printing on perforation area. Only valid to fanfold. Yes：Blank lines between 2 pages. No: No blank lines between 2 pages.

Page 46

Tally Dascom 1330

Paper Setup

Valid Settings

Function

Tear

Auto,Manual, View,Auto@FF

Auto: Form Feed command from the host causes the printer to advance the paper to the tear-off position. Printing resumes on the TOF on next page.

Manual: After the completion of a print job, press a panel key to advance the paper to the tear-off position.

View: No incoming print data in 1~2 seconds after printing completed causes the printer to advance the paper by 2 lines. Printing resumes 2 lines below the torn edge.

Auto@FF: In this setting, a formfeed command is necessary to auto feed the form to tear position.

Paper End Detect

No, Yes

No: The printer stops printing if out of paper.

Yes: The printer continues printing even out of paper.

Compress

Disable, 11:8.2, 13.6:8.2, Auto

Disable: No compression on the print line exceeding the printable width.

Auto: The print squeezes an over-width print line (not exceeding 22" in contents) to the printable width.

Other Compression Ratio: For example, a ratio of 11: 8.2 commands the printer to take this line compression ratio.

**Remark: The compression is disabled after printer reset or loading a new page.

Paper check

Invalid,Anti-jam,Anti-skew, Valid

Place the carriage at proper positions to reduce the chance of paper jam and skew (effective for cut sheets and continuous paper).

Invalid: "Anti-skew" and" Anti-jam" are both invalid.

Anti-jam: After paper is inserted, carriage moves horizontally from end to end. This ensures that minor folds on the paper are ironed out to prevent possible jams.

Anti-skew: After paper is inserted, during the first few lines of printing, the carriage moves to the center to apply pressure on the paper to reduce the chance of paper skew.

Valid: "Anti-skew" and" Anti-jam" are both valid.

Page 47

Tally Dascom 1330

Paper Setup

Valid Settings

Function

Exit Direction

Rear, Front

Selects eject direction for Manual cut sheet paper.

Buzzer

No, Yes

No: Buzzer does not sound if out of paper. Yes: Buzzer sounds if out of paper.

Tear Position

Invalid, Detect, Record

This printer saves the tear-off position before switched off. After switched on, the printer if any change in the tear-off position and determines the start printing position.

Invalid: Printing starts from previously switched off position.

Detect: If the tear-off position is unchanged or smaller, printing starts from TOF position. If larger, printing starts from previously switched off position.

Record: If the tear-off position is unchanged, printing starts from TOF position. If changed, printing starts from previously switched off position.

APW (Auto Paper Width detection)

No, Yes

Yes: Measures the width of the paper automatically after loading the paper.

No: Disables page width measurement. NOTE: Every ex-factory printer equips with a page

width sensor. “APW” appears in this sub-menu.

When the sensor is defective, “APW” disappears from the menu; the 【Power】 LED is off and the【Front Exit】LED blinks, both the【Speed】and【Online】LEDs light up.

APS (Auto Page Skew detection)

Invalid, Normal, Precise

Invalid: The printer will never detect skewness.

Normal: The printer ejects skewed page. Precise: The printer ejects the page even

with low degree of skewness. NOTE: This sensor is an option. Both APS and

BlackMark disappear from this menu if the sensor is not installed or defective.

Page 48

Tally Dascom 1330

Paper Setup

Valid Settings

Function

BlackMark

No, Yes

No: Disables black mark sensor. Yes: Enables black mark sensor. When “Yes” and online, pressing the

【Load/Eject】key advances the paper to the

tear-off position. BlackMark commands: (also see section 5.6)  1D 0C:

Feeds paper to the print position designated by the black mark. Advance the paper to the tear-off position after printing.

 1C 28 4C 03 00 42 m:

m = 0: feeds paper to the print position designated by the black mark. m = 1: feeds paper to the black mark tear-off

position. NOTE: This sensor is an option. Both APS and

BlackMark disappear from this menu if the sensor is not installed or defective.

Width

8.0inch, 8.2inch, PaperWidth

8.0inch: The maximum print width is 80 columns of 10cpi PICA characters.

8.2inch: The maximum print width is 82 columns of 10cpi PICA characters.

Paper Width: Sets the detected page width as print width. Enabling APW is required.

FormLen MicroAdj

-20 -19 -18 -17 -16 -15

-14 -13 -12 -11 -10 -9

-8 -7 -6 -5 -4 -3 -2 -1 0 +1 +2 +3 +4 +5 +6 +7 +8 +9 +10 +11 +12 +13 +14 +15 +16 +17 +18 +19 +20

Fine tunes the form-length by n/360" (0.07mm) based on the default value. (Valid for single papers and fanfolds.)

5.3 Interface Setup

Interface setup

Valid Settings

Function

PnP

No, Yes

No: Disables plug and play for USB Yes: Enables plug and play.

USB ID

No, Yes

No: Disables USB ID. Yes: Enables USB ID

Page 49

Tally Dascom 1330

5.4 Character Setup

Character

setup

Valid Settings

Function

Character Table

Italic, Graphic

Italic: Selects standard character sets. Graphics: Selects IBM character sets.

Please refer to section 12.1.

Character Group

Group 1, Group 2

The interpretation of ASCII codes between 0x80~0x9F:

Group 1: as control codes. Group 1: as printable characters.

Int'l Char Set

USA, France, Germany, UK, DenmarkI, Sweden, Italy, SpainI, Japan, Norway, DenmarkII, Spain II, LatinAm, Denmark, China

International character set selections Font

Roman,SansSerif, Courier, Prestige, Script, OCR B, OCR A, Orator, Gothic, Souvenir

Selects the font. Pitch (cpi)

10, 12, 15, 16.6, 17.1, 20, 24, PROPORTIONAL

Controls the characters per inch setting.

Code Page

CP437, CP737, CP850, CP851, CP852, CP857, CP858, CP860, CP861, CP863, CP864, Extend864, CP865, CP866, Bulgaria866, CP1250, CP1251, CP1252, CP1253, CP1254, 8859_1, 8859_1SAP, 8859_2, 8859_5, 8859_7, 8859_9, 8859_15, BRASCII, Abicomp, Roman8, CoaxTwinax, New437, NewDig850, OldCode860, Flarro863, Hebrew865, CP1257, Ukraine866, Kazakhst866, Kamenicky, Mazovia, Baltic775, CROASCII, Farsi, Urdu, GreekDEC, ELOT928, UK_ASCII, US_ASCII, Swedish, German, Portuguese, French, Italian, Norwegian, Spanish, SiemensTurk, DECTurkish

Code page selections

15cpi Style

Small, Normal

Sets the height for 15CPI character. Small: prints in 1/8” height Normal: prints in full height

AGM(IBM)

No，Yes

Activates or deactivates the AGM (Alternative Graphics Mode) mode in IBM emulation

Page 50

Tally Dascom 1330

5.5 Other Setup

Other Setup

Valid Settings

Function

Form Length Ctrl

No, Yes

No: Software command cannot override the， FormLen in Page Setup.

Yes: Software command overrides the FormLen in Page Setup.

Print Speed Ctrl

No, Yes

No: Software command cannot override the FormLen in Page Setup.

Yes: Software command overrides the FormLen in Page Setup.

Pitch Ctrl

No, Yes

No: Pitch commands are invalid in neither of the emulation.

Yes: Pitch commands are valid either of the emulations.

Font Ctrl

No, Yes

No: Font commands are invalid in neither of the emulation.

Yes: Font commands are valid either of the emulations.

Uni-Dir Ctrl

No, Yes

No: Uni-Direction print commands are invalid in neither of the emulation.

Yes: Uni-Direction print commands are valid in either of the emulations.

Page 51

Tally Dascom 1330

5.5.1 German (Deutsch)

System Setup

Gültige Werte

Language

English,Deutsch,Poccия,Italiano,Français,Español,Türkçe, Portugiesisch.

Emulation

ESC/P2, IBM

Auto CR(ESC/P2)

Ja, Nein

Auto CR(IBM)

Ja, Nein

Auto LF

Ja, Nein

Druck Dir

Bi-Dir, Uni-Dir

Tabellenlinien

Unterbrochen, Verbunden, Gepunktet, Nicht gedruckt

Durchgestrichene

0,Ø

Druckgeschwindigkeit

Normal, Schnell, Ultra

Text Qualität

LQ, NLQ, Entwurf

Ersetze die erste gebrochene Nadel

Aus, 1, 2, 3, 4, 5, 6, 7, 8, 9, 10, 11, 12, 13, 14, 15, 16, 17, 18, 19, 20, 21, 22, 23, 24

Ersetze die zweite gebrochene Nadel

Aus, 1, 2, 3, 4, 5, 6, 7, 8, 9, 10, 11, 12, 13, 14, 15, 16, 17, 18, 19, 20, 21, 22, 23, 24

Belegmodus

Ja, Nein

Energiesparmodus

Aus, 1min, 2min, 5min, 10min

Mehrlagiges Drucken

Ungültig, Normaldurchschlag, Verstärkter Durchschlag,

Impact

Normal, Stark

Grafik Geschwindigkeit

Normal, Schnell, Ultra

Papier Setup

Gültige Werte

Einzel Formularlänge

2.5, 11/4, 3, 3.5, 11/3, 4, 5, 5.5, 6, 7, 8, 9, 10, 11, 12, 14, A4, B4, Define

Einzel Oberer Rand

0, 1/6, 1/4, 1/3, 1/2, 2/3, 3/4, 1, Define

Einzel Unterer Rand

0, 1/6, 1/4, 1/3, 1/2, 2/3, 3/4, 1, Define

Einzelblatt Linker Rand Mikroeinstellung

-7, -6, -5, -4, -3, -2, -1, 0, 1, 2, 3, 4, 5, 6, 7, Define

Einzelblatt Oberer Rand Mikroeinstellung

-7, -6, -5, -4, -3, -2, -1, 0, 1, 2, 3, 4, 5, 6, 7

Einzelblatt Automatisch Papier laden

Disable, 0.5sec, 1sec, 1.5sec, 2sec

Endlos Formularlänge

2.5, 11/4, 3, 3.5, 11/3, 4, 5, 5.5, 6, 7, 8, 9, 10, 11, 12, 14, A4, B4, Define

Endlos Oberer Rand

0, 1/6, 1/4, 1/3, 1/2, 2/3, 3/4, 1, Define

Endlos Unterer Rand

0, 1/6, 1/4, 1/3, 1/2, 2/3, 3/4, 1, Define

Page 52

Tally Dascom 1330

Papier Setup

Gültige Werte

Endlospapier Linker Rand Mikroeinstellung

-7, -6, -5, -4, -3, -2, -1, 0, 1, 2, 3, 4, 5, 6, 7, Define

Endlospapier Oberer Rand Mikroeinstellung

-7, -6, -5, -4, -3, -2, -1, 0, 1, 2, 3, 4, 5, 6, 7

Endlospapier Automatisch Papier laden

Ja, Nein Perforationssprung

Ja, Nein

Abreißen

Automatisches, Manuelles, Kurzes

Papierendeerkennung

Ja, Nein

Stauchung breiter Formate

Disable, 11:8.2, 13.6:8.2, Auto Papierhandhabung

Anti-Schräglauf, Ein, Aus, Anti-Papierstau

Papiereinzugsrichtung

Von hinten, Von vorne

Piepton bei Papierende

Ja, Nein

Speichern der Tearposition

Nein, Erkennen, Speichern Papierbreiterkennung

Ja, Nein

Papierschräglauferkenn ung

Nein, Normal, Genau BlackMark Modus

Ja, Nein

Druckbreite

8.0inch, 8.2inch, PaperWidth

Formularlänge Mikroeinstellung

-20 -19 -18 -17 -16 -15 -14 -13 -12 -11 -10 -9 -8 -7 -6 -5 -4 -3 -2

-1 0 +1 +2 +3 +4 +5 +6 +7 +8 +9 +10 +11 +12 +13 +14 +15 +16 +17 +18 +19 +20

Schnittstellen Setup

Gültige Werte

PnP Funktion

Ja, Nein

USB ID

Ja, Nein

Page 53

Tally Dascom 1330

Erweitertes Setup

Gültige Werte

Kommando für Formularlänge

Ja, Nein

Kommando für Druckgeschwindigkeit

Ja, Nein Pitch Ctrl

Ja, Nein

Font Ctrl

Ja, Nein

Kommando für uni-direktionalen Druck

Ja, Nein

Zeichen Setup

Gültige Werte

Zeichensatz

Standard, IBM

PC-Zeichensatz

Gruppe I, Gruppe II

Land

USA, Frankreich, Deutschland, UK, Dänemark, Schweden, Italien, Spanien, Japan, Norwegen, Dänemark II, Spanien II, Latein-Amerika, Dänemark/Norwegen, China

Font

Roman,SansSerif, Courier, Prestige, Script, OCR B, OCR A, Orator, Gothic, Souvenir

Pitch(cpi)

10, 12, 15, 16.6, 17.1, 20, 24, PROPORTIONAL

Code Page

15cpi Style

Schmal, Normal

AGM(IBM)

Ja, Nein

Page 54

Tally Dascom 1330

5.5.2 Russian (Россия)

обновление системы

Правильные значения

Language

English,Deutsch,Poccия,Italiano,Français,Español, Türkçe, Португальский.

Эмуляция

ESC/P2, IBM

Авто CR(ESC/P2)

Да, Нет

Авто CR(IBM)

Да, Нет

Авто LF

Да, Нет

Однонаправленная

Bi-Dir, Uni-Dir

Контурная линия

отключен, Подключен, точечная линия, отсутствие печати

Slashed Zero Ø

0,Ø

Скорость печати

Normal, Fast, Ultra

Качество текста

LQ, NLQ, проект

Заменa первой сломанной иглы

No, 1, 2, 3, 4, 5, 6, 7, 8, 9, 10, 11, 12, 13, 14, 15, 16, 17, 18, 19, 20, 21, 22, 23, 24

Заменa второй сломанной иглы

No, 1, 2, 3, 4, 5, 6, 7, 8, 9, 10, 11, 12, 13, 14, 15, 16, 17, 18, 19, 20, 21, 22, 23, 24

Профильный режим Slip

Да, Нет Экономный режим

OFF, 1min, 2min, 5min, 10min

Многослойная печать

недействительно, Обычная копия, усиленная копия,

Ударный режим печати

Normal, Heavy

Скорость графики

Normal, Fast, Ultra

Настройка бумаги

Правильные значения

Длина формы для отдельных листов

2.5, 11/4, 3, 3.5, 11/3, 4, 5, 5.5, 6, 7, 8, 9, 10, 11, 12, 14, A4, B4, Define

Отступ сверху для отдельных листов

0, 1/6, 1/4, 1/3, 1/2, 2/3, 3/4, 1, Define

Отступ снизу для отдельных листов

0, 1/6, 1/4, 1/3, 1/2, 2/3, 3/4, 1, Define

Микронастройка левого поля бумаги в виде отдельных листов

-7, -6, -5, -4, -3, -2, -1, 0, 1, 2, 3, 4, 5, 6, 7, Define

Микронастройка верхнего поля бумаги в виде отдельных листов

-7, -6, -5, -4, -3, -2, -1, 0, 1, 2, 3, 4, 5, 6, 7

Автоматическая загрузка бумаги в виде отдельных листов

Disable, 0.5sec, 1sec, 1.5sec, 2sec

Page 55

Tally Dascom 1330

Настройка бумаги

Правильные значения

Длина формы для непрерывной бумаги

2.5, 11/4, 3, 3.5, 11/3, 4, 5, 5.5, 6, 7, 8, 9, 10, 11, 12, 14, A4, B4, Define

Отступ сверху для непрерывной бумаги

0, 1/6, 1/4, 1/3, 1/2, 2/3, 3/4, 1, Define

Отступ снизу для непрерывной бумаги

0, 1/6, 1/4, 1/3, 1/2, 2/3, 3/4, 1, Define

Микронастройка левого поля фальцованной форматированной бумаги

-7, -6, -5, -4, -3, -2, -1, 0, 1, 2, 3, 4, 5, 6, 7, Define

Микронастройка верхнего поля фальцованной форматированной бумаги

-7, -6, -5, -4, -3, -2, -1, 0, 1, 2, 3, 4, 5, 6, 7

Fanfold Form Automatic Paper Loading

Да, Нет Пропуск перфорации

Да, Нет

Отрыв бумаги

Автоматический отрыв бумаги, ручной отрыв бумаги, короткий отрыв бумаги

Определение конца бумаги

Да, Нет

Сжатие широкой форматной бумаги

Disable, 11:8.2, 13.6:8.2, Auto

Подготовка бумаги к печати

Защита от перекоса, действительно, недействительно, защита от заедания бумаги

Направление фрикционной подачи бумаги

Сзади, спереди

Звуковой сигнал при отсутствии бумаги

Да, Нет Запись позиции отрыва

Недействительно, определение, запись

Определение ширины бумаги

Да, Нет

Определение наклона бумаги

Недействительный, обычный, точный Режим черной метки

Да, Нет

Ширина печати

8.0inch, 8.2inch, PaperWidth

Микронастройка длины форматной бумаги

-20 -19 -18 -17 -16 -15 -14 -13 -12 -11 -10 -9 -8 -7 -6 -5 -4

-3 -2 -1 0 +1 +2 +3 +4 +5 +6 +7 +8 +9 +10 +11 +12 +13 +14 +15 +16 +17 +18 +19 +20

Функция PnP

Да, Нет

USB ID

Да, Нет

Page 56

Tally Dascom 1330

Настройка интерфейс

Правильные значения

Функция PnP

Да, Нет

USB ID

Да, Нет

Настройка

символов

Правильные значения

Набор символов

Стандартный, IBM

Группа символов

Группа I, группа II

Набор знаков

USA, France, Germany, UK, Дания, Sweden, Italy, Spain, Japan, Норвегия, Дания II, Spain II, Латинская Америка, Дания/Норвегия, Китай

Font

Roman,SansSerif, Courier, Prestige, Script, OCR B, OCR A, Orator, Gothic, Souvenir

Pitch(cpi)

10, 12, 15, 16.6, 17.1, 20, 24, PROPORTIONAL

Code Page

15cpi Style

Small, Normal

AGM(IBM)

Да, Нет

Другие настройки

Правильные значения

Команда длины форматной бумаги

Да, Нет

Команда скорости печати

Да, Нет

Pitch Ctrl

Да, Нет

Font Ctrl

Да, Нет

Команда однонаправленной печати

Да, Нет

Page 57

Tally Dascom 1330

5.5.3 Italian (Italiano)

Setup sistema

Impostazioni Valide

Language

English,Deutsch,Poccия,Italiano,Français,Español, Türkçe, Portoghese.

Emulazione

ESC/P2, IBM

Auto CR(ESC/P2)

Si, No

Auto CR(IBM)

Si, No

Auto LF

Si, No

Stampa Uni-Dir

Bi-Dir, Uni-Dir

Linee Formato

Disconnessa, Connessa, riga aghi, Non stampa

Zero barrato

0,Ø

Velocità stampa

Normale, Veloce, Ultra

Qualità Testo

LQ, NLQ, bozza

Sostituire primo ago rotto

No, 1, 2, 3, 4, 5, 6, 7, 8, 9, 10, 11, 12, 13, 14, 15, 16, 17, 18, 19, 20, 21, 22, 23, 24

Sostituire secondo ago rotto

No, 1, 2, 3, 4, 5, 6, 7, 8, 9, 10, 11, 12, 13, 14, 15, 16, 17, 18, 19, 20, 21, 22, 23, 24

Impostazioni moduli piccoli

Si, No

Modo risparmio energia

OFF, 1min, 2min, 5min, 10min

Stampa multicopia

Non valido, Copia normale, maggior impatto

Modo impatto

Normale, Pesante

Velocità Grafica

Normale, Veloce, Ultra

Imposta carta

Impostazioni Valide

Lunghezza Foglio

2.5, 11/4, 3, 3.5, 11/3, 4, 5, 5.5, 6, 7, 8, 9, 10, 11, 12, 14, A4, B4, Define

Margine Sup. Foglio

0, 1/6, 1/4, 1/3, 1/2, 2/3, 3/4, 1, Define

Margine Infer. Foglio

0, 1/6, 1/4, 1/3, 1/2, 2/3, 3/4, 1, Define

Microregolazione foglio sinistra

-7, -6, -5, -4, -3, -2, -1, 0, 1, 2, 3, 4, 5, 6, 7, Define Microregolazione in alto foglio

-7, -6, -5, -4, -3, -2, -1, 0, 1, 2, 3, 4, 5, 6, 7

Carica automatica foglio singolo

Disable, 0.5sec, 1sec, 1.5sec, 2sec

Lungh. Mod. Continuo

2.5, 11/4, 3, 3.5, 11/3, 4, 5, 5.5, 6, 7, 8, 9, 10, 11, 12, 14, A4, B4, Define

Margine Sup. Continuo

0, 1/6, 1/4, 1/3, 1/2, 2/3, 3/4, 1, Define

Margine Inf. Continuo

0, 1/6, 1/4, 1/3, 1/2, 2/3, 3/4, 1, Define

Microregolazione SX modulo continuo

-7, -6, -5, -4, -3, -2, -1, 0, 1, 2, 3, 4, 5, 6, 7, Define

Page 58

Tally Dascom 1330

Imposta carta

Impostazioni Valide

Microregolazione in alto modulo continuo

-7, -6, -5, -4, -3, -2, -1, 0, 1, 2, 3, 4, 5, 6, 7

Carica automatica modulo continuo

Si, No

Salto Perforazione

Si, No

Strappo

Auto Strappo, Strappo manuale, Strappo corto

Controllo fine carta

Si, No

Larghezza formato compressa

Disable, 11:8.2, 13.6:8.2, Auto

Gestione carta

Anti-scivolamento,Valido,Invalido,Anti-inceppamento

Direzione frizione carta

Retro, Frontale

Avviso sonoro a fine carta

Si, No

Registra posizione strappo carta

Invalido, Rileva, Registra Rilevamento larghezza carta

Si, No

Rilevamento scivolamento carta

Invalido, Normale, Preciso Modalità segno di riferimento

Si, No

Larghezza stampa

8.0inch, 8.2inch, PaperWidth

Microregolazione lunghezza carta modulo continuo

-20 -19 -18 -17 -16 -15 -14 -13 -12 -11 -10 -9 -8 -7 -6 -5 -4

-3 -2 -1 0 +1 +2 +3 +4 +5 +6 +7 +8 +9 +10 +11 +12 +13 +14 +15 +16 +17 +18 +19 +20

Setup IF

Impostazioni Valide

Funzione PnP

Si, No

USB ID

Si, No

Page 59

Tally Dascom 1330

Imposta caratteri

Impostazioni Valide

Set caratteri

Standard, IBM

Gruppo Carattere

Group I, Group II

Set Carat. Int.

USA,Francia, Germania, Regno Unito, Danimarca, Svezia, Italia, Spagna, Giappone, Norvegia, Danimarca II, Spagna II, America Latina, Danimarca/Norvegia, Porcellana

Font

Roman,SansSerif, Courier, Prestige, Script, OCR B, OCR A, Orator, Gothic, Souvenir

Pitch(cpi)

10, 12, 15, 16.6, 17.1, 20, 24, PROPORTIONAL

Code Page

15cpi Style

Small, Normal

AGM(IBM)

Si, No

Altri Setup

Impostazioni Valide

Comando lunghezza carta

Si, No

Comando velocità stampa

Si, No

Pitch Ctrl

Si, No

Font Ctrl

Si, No

Comando stampa monodirezionale

Si, No

Page 60

Tally Dascom 1330

5.5.4 French (Français)

Réglage papier

Paramètres Valides

Feuille à feuille Longueur formulaire

2.5, 11/4, 3, 3.5, 11/3, 4, 5, 5.5, 6, 7, 8, 9, 10, 11, 12, 14, A4, B4, Define

Feuille à feuille Bord supérieur

0, 1/6, 1/4, 1/3, 1/2, 2/3, 3/4, 1, Define

Feuille à feuille Bord inférieur

0, 1/6, 1/4, 1/3, 1/2, 2/3, 3/4, 1, Define

Feuille à feuille Micro-ajustement Marge Gauche

-7, -6, -5, -4, -3, -2, -1, 0, 1, 2, 3, 4, 5, 6, 7, Define

Feuille à feuille Micro-ajustement Marge Supérieure

-7, -6, -5, -4, -3, -2, -1, 0, 1, 2, 3, 4, 5, 6, 7

Feuille à feuille Chargement Automatique Papier

Disable, 0.5sec, 1sec, 1.5sec, 2sec

Papier continu Longueur formulaire

2.5, 11/4, 3, 3.5, 11/3, 4, 5, 5.5, 6, 7, 8, 9, 10, 11, 12, 14, A4, B4, Define

Papier continu Bord supérieure

0, 1/6, 1/4, 1/3, 1/2, 2/3, 3/4, 1, Define

Papier continu Bord inférieure

0, 1/6, 1/4, 1/3, 1/2, 2/3, 3/4, 1, Define

Réglage Système

Paramètres Valides

Language

English,Deutsch,Poccия,Italiano,Français,Español,Türkçe, Portugais.

Emulation

ESC/P2, IBM

RC-Auto(ESC/P2)

Oui, Non

RC-Auto(IBM)

Oui, Non

SL-Auto

Oui, Non

Uni-dir Impr

Bi-Dir, Uni-Dir

Ligne formée

Discontinue, Continue, Pointillé, Non imprimée

Zero barrato

0,Ø

Qualité Mode Texte

LQ, NLQ, avant-projet

Vitesse Impression

Normal, Rapide, Ultra

Substituez la 1ère aiguille cassée

Non, 1, 2, 3, 4, 5, 6, 7, 8, 9, 10, 11, 12, 13, 14, 15, 16, 17, 18, 19, 20, 21, 22, 23, 24

Substituez la 2ème aiguille cassée

Non, 1, 2, 3, 4, 5, 6, 7, 8, 9, 10, 11, 12, 13, 14, 15, 16, 17, 18, 19, 20, 21, 22, 23, 24

Mode profil Fiche

Oui, Non

Modo risparmio energia

OFF, 1min, 2min, 5min, 10min

Impression multi-épaisseurs

Invalide, Copie normale, Copie renforcée

Mode Impact

Normal, Forte

Vitesse Graphique

Normal, Rapide, Ultra

Page 61

Tally Dascom 1330

Réglage papier

Paramètres Valides

Enregistrement de la Position de Coupe

Non, Détecter, Enregistrer Détection Largeur Papier

Oui, Non

Détection Papier en Biais

Non, Normal, Précis

Mode Repère Noir

Oui, Non

Largeur Impression

8.0inch, 8.2inch, PaperWidth

Longueur Page Micro-ajustement

-20 -19 -18 -17 -16 -15 -14 -13 -12 -11 -10 -9 -8 -7

-6 -5 -4 -3 -2 -1 0 +1 +2 +3 +4 +5 +6 +7 +8 +9 +10 +11 +12 +13 +14 +15 +16 +17 +18 +19 +20

Papier continu Micro-ajustement Marge Gauche

-7, -6, -5, -4, -3, -2, -1, 0, 1, 2, 3, 4, 5, 6, 7, Define

Papier continu Micro-ajustement Marge Supérieure

-7, -6, -5, -4, -3, -2, -1, 0, 1, 2, 3, 4, 5, 6, 7

Papier continu Chargement Automatique Papier

Oui, Non Saut perforation

Oui, Non

Coupe

Coupe Auto, Coupe Manuelle, Coupe Courte

Détection Fin Papier

Oui, Non

Compression ensemble de la page

Disable, 11:8.2, 13.6:8.2, Auto

Gestion Papier

Anti-biais, Oui, Non, Anti-bourrage

Friction Direction Alimentation Papier

Arrière, Avant

Alarme si Fin de Papier

Oui, Non

Config Interface

Paramètres Valides

Fonction PnP

Oui, Non

USB ID

Oui, Non

Page 62

Tally Dascom 1330

Config. Caractère

Paramètres Valides

Jeu Caractères

Standard, IBM

Groupe Caractères

Groupe 1, Groupe 2

Pays

USA, France, Allemagne, Royaume-Uni, Denmark, Suède, Italie, Espagne, Japon, Norvège, Denmark II, Espagne II, Amerique latine, Denmark/Norvège, Chine

Font

Roman,SansSerif, Courier, Prestige, Script, OCR B, OCR A, Orator, Gothic, Souvenir

Pitch(cpi)

10, 12, 15, 16.6, 17.1, 20, 24, PROPORTIONAL

Code Page

15cpi Style

Small, Normal

AGM(IBM)

Oui, Non

Autre réglage

Paramètres Valides

Commande Longueur de Page

Oui, Non

Commande Vitesse Impresssion

Oui, Non

Pitch Ctrl

Oui, Non

Font Ctrl

Oui, Non

Commande Impression Uni-Directionnelle

Oui, Non

Page 63

Tally Dascom 1330

5.5.5 Spanish (Español)

Config. Sistema

Ajustes validos

Language

English,Deutsch,Poccия,Italiano,Français,Español,Türkçe, Portugués.

Emulación

ESC/P2, IBM

Auto CR(ESC/P2)

Si, No

Auto CR(IBM)

Si, No

Auto LF

Si, No

Uni-Dir

Bi-Dir, Uni-Dir

Linea del Formato

Desconectado, Conectado, Línea de Punto, Sin Impresión

Slashed Zero Ø

0,Ø

Velocidad de Impresión

Normal, Fast, Ultra

Tipo de calidad de texto

LQ, NLQ, proyecto

Sustituir 1er pin roto

Non, 1, 2, 3, 4, 5, 6, 7, 8, 9, 10, 11, 12, 13, 14, 15, 16, 17, 18, 19, 20, 21, 22, 23, 24

Sustituir 2do pin roto

Non, 1, 2, 3, 4, 5, 6, 7, 8, 9, 10, 11, 12, 13, 14, 15, 16, 17, 18, 19, 20, 21, 22, 23, 24

Perfil Modo Slip

Si, No

Modo Ahorro de Energía

OFF, 1min, 2min, 5min, 10min

Impresión Multi-Copias

Inválido, Copia Normal, Copia Fuerte

Modo de Impacto

Normal, Fuerte

Seleciona diferentes qualidades de impressão

Normal, Fast, Ultra

Config. Papel

Ajustes validos

Tamaño Hojas Sueltas

2.5, 11/4, 3, 3.5, 11/3, 4, 5, 5.5, 6, 7, 8, 9, 10, 11, 12, 14, A4, B4, Define

Margen Sup. Folios

0, 1/6, 1/4, 1/3, 1/2, 2/3, 3/4, 1, Define

Margen Inf. Folios

0, 1/6, 1/4, 1/3, 1/2, 2/3, 3/4, 1, Define

Micro Ajus. Marg. Izq. Hoja Suelta

-7, -6, -5, -4, -3, -2, -1, 0, 1, 2, 3, 4, 5, 6, 7, Define

Micro Ajus. Marg. Der. Hoja Suelta

-7, -6, -5, -4, -3, -2, -1, 0, 1, 2, 3, 4, 5, 6, 7 Carga de Papel Auto. Hoja Suelta

Disable, 0.5sec, 1sec, 1.5sec, 2sec

Tamaño Papel Continuo

2.5, 11/4, 3, 3.5, 11/3, 4, 5, 5.5, 6, 7, 8, 9, 10, 11, 12, 14, A4, B4, Define

Margen Sup. Pap Cont.

0, 1/6, 1/4, 1/3, 1/2, 2/3, 3/4, 1, Define

Margen Inf. Pap.Cont.

0, 1/6, 1/4, 1/3, 1/2, 2/3, 3/4, 1, Define

Micro Ajus. Marg. Der. Pap. Cont.

-7, -6, -5, -4, -3, -2, -1, 0, 1, 2, 3, 4, 5, 6, 7, Define

Micro Ajus. Marg. Der. Pap. Cont.

-7, -6, -5, -4, -3, -2, -1, 0, 1, 2, 3, 4, 5, 6, 7

Carga de Papel Auto. Hoja Suelta

Si, No

Page 64

Tally Dascom 1330

Config. Papel

Ajustes validos

Salto perforación

Si, No

Corte

Corte Auto, Corte Manual, Corte Corto

Detección Fin de Papel

Si, No

Compresión de Form. Ancho

Disable, 11:8.2, 13.6:8.2, Auto

Manejo de Papel

Anti-desvío, Válido, Inválido, Anti-atasco

Dirección de Alim. De Papel por Fricción

Posterior, Frontal

Alarma si no hay papel

Si, No

Registro de Posición de Corte

Inválido, Detectar, Registrar

Detección Ancho de Papel

Si, No

Detección Desvío de Papel

Inválido, Normal, Preciso

Modo Marca Negra

Si, No

Ancho de Impresión

8.0inch, 8.2inch, PaperWidth

Micro-Ajus. Long. Hoja

-20 -19 -18 -17 -16 -15 -14 -13 -12 -11 -10 -9 -8

-7 -6 -5 -4 -3 -2 -1 0 +1 +2 +3 +4 +5 +6 +7 +8 +9 +10 +11 +12 +13 +14 +15 +16 +17 +18 +19 +20

Conf. Interface

Ajustes validos

Función PnP

Si, No

USB ID

Si, No

Config. Carácter

Ajustes validos

Juego de Caracteres

Estándar, IBM

Grupo de Caracteres

Grupo I, Grupo II

Carácter Local

USA, Francia, Alemania, Reino Unido, Dinamarca, Suecia, Italia, España, Japón, Noruega, Dinamarca II, España II, AméricaLatina, Dinamarca, China

Font

Roman,SansSerif, Courier, Prestige, Script, OCR B, OCR A, Orator, Gothic, Souvenir

Pitch(cpi)

10, 12, 15, 16.6, 17.1, 20, 24, PROPORTIONAL

Code Page

15cpi Style

Small, Normal

AGM(IBM)

Si, No

Page 65

Tally Dascom 1330

Config. Otros

Ajustes validos

Comando Longitud de Hoja

Si, No

Comando Velocidad de Impresión

Si, No

Pitch Ctrl

Si, No

Font Ctrl

Si, No

Comando Impresión Uni-direccional

Si, No

5.5.6 Turkish (Türkce)

Sistem Ayarı

Geçerli ölçüler

Language

English,Deutsch,Poccия,Italiano,Français,Español,Türkçe, Portekizce.

Emülasyon

ESC/P2, IBM

Otom. Satırbaşı(ESC/P2)

Evet, Hayır

Otom. Satırbaşı(IBM)

Evet, Hayır

Otom. Satır besleme

Evet, Hayır

Tek-Yön baskı

Bi-Dir, Uni-Dir

Kağıt satırı

Bağlı değil, Bağlandı, Nokta satırı, Baskı yok

Slashed Zero Ø

0,Ø

Metin kalitesi

LQ, NLQ, taslak

Yazıcı Hızı

Normal, Fast, Ultra

Arızalı ilk iğne yedeği

Hayır, 1, 2, 3, 4, 5, 6, 7, 8, 9, 10, 11, 12, 13, 14, 15, 16, 17, 18, 19, 20, 21, 22, 23, 24

Arızalı ikinci iğne yedeği

Hayır, 1, 2, 3, 4, 5, 6, 7, 8, 9, 10, 11, 12, 13, 14, 15, 16, 17, 18, 19, 20, 21, 22, 23, 24

Slip profile mode

Evet, Hayır

Enerji tasarrufu modu

OFF, 1min, 2min, 5min, 10min

Çok katmanlı baskı

Geçersiz, Normal kopya, Güçlendirilmiş kopya

Vuruş modu

Normal, Heavy

Farklı baskı özellikleri seçer

Normal, Fast, Ultra

Page 66

Tally Dascom 1330

Kağıt Ayarı

Geçerli ölçüler

Tek-kağıt Form uzunluğu

2.5, 11/4, 3, 3.5, 11/3, 4, 5, 5.5, 6, 7, 8, 9, 10, 11, 12, 14, A4, B4, Define

Tek-kağıt Üst kenar boşluğu

0, 1/6, 1/4, 1/3, 1/2, 2/3, 3/4, 1, Define

Tek-kağıt Alt kenar boşluğu

0, 1/6, 1/4, 1/3, 1/2, 2/3, 3/4, 1, Define

Tek-kağıt Sol kenar boşluğu hassas ayar

-7, -6, -5, -4, -3, -2, -1, 0, 1, 2, 3, 4, 5, 6, 7, Define

Tek-kağıt Üst kenar boşluğu hassas ayar

-7, -6, -5, -4, -3, -2, -1, 0, 1, 2, 3, 4, 5, 6, 7 Tek-kağıt otomatik kağıt yükleme

Disable, 0.5sec, 1sec, 1.5sec, 2sec

Sürekli Form Kağıt Uzunluğu

2.5, 11/4, 3, 3.5, 11/3, 4, 5, 5.5, 6, 7, 8, 9, 10, 11, 12, 14, A4, B4, Define

Sürekli Form Kağıt Üst kenar boşluğu

0, 1/6, 1/4, 1/3, 1/2, 2/3, 3/4, 1, Define

Sürekli Form Kağıt Alt kenar boşluğu

0, 1/6, 1/4, 1/3, 1/2, 2/3, 3/4, 1, Define

Sürekli Form Kağıt Sol kenar hassas ayar

-7, -6, -5, -4, -3, -2, -1, 0, 1, 2, 3, 4, 5, 6, 7, Define

Sürekli Form Kağıt Üst kenar hassas ayar

-7, -6, -5, -4, -3, -2, -1, 0, 1, 2, 3, 4, 5, 6, 7 Sürekli Form Otomatik Kağıt Yükleme

Evet, Hayır

Delik atlama

Evet, Hayır

Kağıt kesme

Otomatik kesim, Elle kesim, Kısa kesim

Sayfa sonu algılama

Evet, Hayır

Geniş Baskı sıkıştırma

Disable, 11:8.2, 13.6:8.2, Auto

Eğrilik önleme

Geçerli, Geçersiz, Sıkışıklık önleme

Kağıt Besleme Yönü seçme

Arka besleme, Ön Besleme

Kağıt bitme vızıldama alarmı

Evet, Hayır

Kağıt Kesme Pozisyonu hafıza kaydı

Geçersiz, Algılama, Hafıza kayıt

Kağıt genişlik algılaması

Evet, Hayır

Kağıt eğrilik algılaması

Geçersiz, Normal, Tam

Siyah Çizgi algılama Modu

Evet, Hayır

Baskı Genişliği

8.0inch, 8.2inch, PaperWidth

Kağıt uzunluğu hassas ayarlama

-20 -19 -18 -17 -16 -15 -14 -13 -12 -11 -10 -9 -8 -7

-6 -5 -4 -3 -2 -1 0 +1 +2 +3 +4 +5 +6 +7 +8 +9 +10 +11 +12 +13 +14 +15 +16 +17 +18 +19 +20

Bağlantı Ayarı

Geçerli ölçüler

PnP işlevi

Evet, Hayır

USB ID

Evet, Hayır

Page 67

Tally Dascom 1330

Karakter ayarı

Geçerli ölçüler

Karakter Set

Standart, IBM

Karakter Grubu

Grup I, Grup II

Uluslararası Kar. Seti

Amerika Bir.Devleti, Fransa, Almanya, İngiltere, Danimarka, İsveç, İtalya, İspanya, Japonya, Norveç, Danimarka II, İspanya II, Latin Amerika, Danimarka, Çin

Font

Roman,SansSerif, Courier, Prestige, Script, OCR B, OCR A, Orator, Gothic, Souvenir

Pitch(cpi)

10, 12, 15, 16.6, 17.1, 20, 24, PROPORTIONAL

Code Page

15cpi Style

Small, Normal

AGM(IBM)

Evet, Hayır

Diğer Ayarlar

Geçerli ölçüler

Kağıt Uzunluğu Komutu

Evet, Hayır

Baskı Hızı Komutu

Evet, Hayır

Pitch Ctrl

Evet, Hayır

Font Ctrl

Evet, Hayır

Tek yön baskı Komutu

Si, No

Page 68

Tally Dascom 1330

5.6 Black Mark Parameters

This printer uses tractors to load fanfold forms with pre-printed black marks. The printer requires 3 parameters to print on paper with black marks:

1. Horizontal offset of black mark from the edge of page (called Black Mark Physical Horizontal Position); later on, this value facilitates the printer to locate its scanner preparing for identifying the black marks.

2. Vertical offset of the first print line from the black mark (called Distance Offset From Black Mark To Print Position); later on, the print makes use of this value to print the first line relative to the black mark.

3. Vertical offset of the tear-off edge from the black mark (called Distance Offset From Black Mark To Tear Position); this value informs the printer the tear-off position of the page.

Not to skip or change the order of setting the above 3 parameters.

The procedures to set the parameters:

1. Hold down the【Load/Eject】key while powering on the printer and then release the key when the Print Head starts to move. After loading paper, the printer prompts the Printer Settings

Printer Settings

[LF]=Next, [TOP]=Back, [LOAD/EJECT]=OK, [ONLINE]=Exit, [ONLINE]+[LOAD/EJECT]= Save and restart the printer.

System Setup

2. Press the Next or Back keys to scroll forward or backward the sub-menus till the printer shows:

BlackMark Mode

3. Press OK to go into the BlackMark menu. The printer prompts:

[Black Mark Adjustment Mode] [LF]=Next, [TOP]=Back, [LOAD/EJECT]=OK, [ONLINE]=Exit, [ONLINE]+[LOAD/EJECT]= Save and restart the printer.

Black Mark Physical Horizontal Position Press any key to eject the paper, and load paper with black mark in the Fanfold Path.

4. The last prompt above advises you to press any key to unload the dialog form. Then load a fanfold form with black mark.

Keys act as proxies for designated functions in the setting dialog.

Page 69

Tally Dascom 1330

5. Ensure to place the lever at position. Then press the【Load/Eject】key to load the black marked form. The top edge of the form will then align with the printer’s tear-off blade. Press Next or Back until you see the black mark marginally exposed out of the tear-off blade. Then press OK to allow the printer to scan the horizontal offset of the black mark relative to the left edge of the page. (Meanwhile, the vertical position of the black mark is measured and recorded.) When the printer fails to scan the horizontal offset, it prompts you to repeat the above procedures. If scanning is successful, it prompts:

Successfully setup black mark parameters.

Distance Offset From Black Mark To Print Position

6. The last prompt above invites you to set the next parameter --- vertical offset of the first print line from the black mark. Like other setting dialogs, you have options:

1) to bypass this setting (by pressing Next or Back), (WARNING: Not to skip or

change the order in Black Mark Setting.)

2) to accept the invitation (by pressing OK),

3) to leave the subsequent settings (by press Exit), or

4) to terminate the session and save modified parameter(s) (by pressing Save and Restart).

7. When you respond with “OK” to set the vertical offset, the printer prompts you to reload a black marked fanfold form:

Press any key to eject the paper, and load paper with black mark in the Fanfold Path.

8. The top edge of the form will then align with the printer’s tear-off blade. Press Next or Back to feed or reverse-feed the paper till the desired first print line position is reached. (With the above measured vertical position, the printer will convert the net paper feeding to the TOF relative to the black mark.) Press OK to confirm the vertical offset. Then the print prompts the invitation for setting the tear-off position relative to the black mark:

Successfully setup black mark parameters.

Distance Offset From Black Mark To Tear Position

9. When you respond with OK to set the tear-off position, the printer prompts you to reload a black marked fanfold form:

Press any key to eject the paper,and load paper with black mark in the Fanfold Path.

Page 70

Tally Dascom 1330

10. The printer reloads the form. By default the form stops 5.5 inches away from the printer’s tear-off blade. Press Next or Back to feed or reverse-feed the paper till the desired tear-off position is reached. (With the above measured vertical position, the printer will convert the net paper feeding to the tear-off position relative to the black mark.) Press OK to confirm the tear-off offset relative to the black mark. Finally, press Save and Restart to save new settings and terminate the session.

5.7 Bi-directional Alignment

When wiggling vertical grids appears in tabular reports, you should adjust the Bi-directional Alignment.

The procedures to adjust bi-directional alignment across adjacent line grids:

1. Hold down the【Load/Eject】key while powering on the printer and then release the key when the Print Head starts to move. After loading paper, the printer prompts the Printer Settings

Printer Settings

[LF]=Next, [TOP]=Back, [LOAD/EJECT]=OK, [ONLINE]=Exit, [ONLINE]+[LOAD/EJECT]= Save and restart the printer.

System Setup

2. Press the Next or Back keys to scroll forward or backward the sub-menus till the printer shows:

Bi-directional Alignment

3. Press OK to go into the Bi-directional Alignment menu. The printer prompts:

[Bidirection Test] [TOP]=-1, [LF]=+1, [LOAD/EJECT]=OK, [ONLINE]=Back, [ONLINE]+[LOAD/EJECT]=Save and restart the printer

| | | | | | | | | | | | | | | | | | | | | | | | | | | | | |

Misalignment observed

Keys act as proxies for designated functions in the setting dialog.

Page 71

Tally Dascom 1330

4. Every press on “+1” or “-1” shifts the second line to the right or left, respectively, relative to the top line by 1 fine step. After pressing “+1” twice and then “OK”, the printer prompts:

| | | | | | | | | | | | | | | | | | | | | | | | | | | | | |

5. Repeat the adjustment till two grid lines align satisfactory as “|”. Press “OK” again. The printer asks if you want to save the correction:

Save the parameter settings ([LOAD/EJECT] or [ONLINE] = OK, [LF] = Next)?

Yes

6. At this stage, you have the options to save or give up the correction by pressing OK or Next, respectively. If you respond with OK, an asterisk “*” appends to “Yes” to confirm saving change. If you intend to give up the correction by pressing Next, the printer prompts a “No” Then a confirmative response of OK appends an asterisk “*” to the “No” prompt. The printer then exits the Bi-directional Alignment and proceeds with the next setup menu.

5.8 Restore Factory Default

The procedures to restore factory default settings;

1. Hold down the【Load/Eject】key while powering on the printer and then release the key when the Print Head starts to move. After loading paper, the printer prompts the Printer Settings

Printer Settings

[LF]=Next, [TOP]=Back, [LOAD/EJECT]=OK, [ONLINE]=Exit, [ONLINE]+[LOAD/EJECT]= Save and restart the printer.

System Setup

2. Press the Next or Back keys to scroll forward or backward the sub-menus till the printer shows:

Restore Factory Default

Misalignment reduced

Keys act as proxies for designated functions in the setting dialog.

Page 72

Tally Dascom 1330

3. Press OK to go into restore factory default dialog. The printer prompts:

[Restore Factory Default]

Restore factory settings ([LOAD/EJECT]=OK, [ONLINE]=Exit)?

Yes

4. At this stage you have the option of OK to restore default setting or Exit to discard the restoration.

5. If input OK, the printer prints an asterisk “*” appending the “Yes” and prompts successful restoration:

Restore factory settings successfully

6. The printer beeps once to indicate successful restoration.

5.9 Tally Dascom Printer Config Tool

In the CDROM is a software utility called “Tally Dascom Printer Config Tool”. This application enables a convenient, simple, and fast way to control your printer without touching any keys on the operation panel.

1. Start the tool installation by double clicking the “Tally Dascom Printer Config Tool Setup.msi”.

2. Connect the printer to the system using USB cable

3. Power up the printer.

4. Run the tool from the Windows Start menu by selecting All Programs, then Dascom Printer Setup, and then Tally Dascom Printer Setup.

5. For more information on how to use the tool, go to the Help menu and select User Guide.

Page 73

Tally Dascom 1330

6 Customized Form

This printer allows the customization on the form length, TOF, bottom margin and left margin for single sheets and fanfold. Restore Factory Defaults can recover these default values.

Selecting the Define value(s) in section 5.3 (Paper Setup menu) allows the printer to take up the customized page formatting value(s).

The parameter setting procedures involve:

1. The printer prompts the dialogs and you follow the prompts.

2. Before every measurement or change, the print instructs you to unload the Setup Instruction Page from the printer.

3. With the exception of measuring the form length for cut sheets, always set the lever to the tractors position .

4. For form length measurement, insert the customized form from the proper paper path.

The other six settings are actually done on general fanfold forms --- not the actual customized form. Fanfold paper gives direct visual results on the TOF, bottom and left margins even though cut sheets will be used in actual applications.

6.1 Customize Cut Sheet Form Length

1. Hold down both the【Online】and 【TOF】keys while powering on the printer and then release the keys when the carriage initializes and beeps once. After loading a form the printer prompts:

Customized Form

[LF]=Next, [TOP]=Back, [LOAD/EJECT]=OK, [ONLINE]=Exit, [ONLINE]+[LOAD/EJECT]= Save and restart the printer.

Single sheet

2. Press “OK” to start customizing all or part of 4 parameters for single sheet. The printer prompts:

[Single sheet]

Form Length

Keys act as proxies for designated functions in the setting dialog.

Page 74

Tally Dascom 1330

3. You may skip to other customized settings by pressing “Next” or “Back”. Once you press “OK” to continue with form length measurement, the printer prompts:

1. Press any key to clear the Setup Instructions Page from the printer.

Insert the Customized Page into the corresponding paper path. Press [LOAD/EJECT] to load and measure the page length

2. The printer rolls over the entire Customized Page to measure its length.

After measurement, press [LOAD/EJECT] to load a blank Setup Instructions Page to report the measured value.

3. Press [LOAD/EJECT] to save the measured value.

Repeat the above steps if the printed value is dissatisfactory.

illustrations for above step 1 and step 2.

Page 75

Tally Dascom 1330

4. Follow the given prompt to unload the Setup Instruction Page. Load the customized form to allow the printer to scan the page length. After the measurement, load another Setup Instruction Page to let the printer print out the measured length.

The measured form length is: 11.0”, approximately equal to 279mm, accuracy of plus or minus 0.1 inches. The measured value has been saved. Remeasure ( [LOAD/EJECT]=OK, [ONLINE] =Exit)?

Yes

5. At this stage: If【Load/Eject】key is pressed, an asterisk “*” is appended to “Yes” and you should repeat the procedures for form length measurement as mentioned. Or, If you input “Exit”, the printer saves the measurement value and proceeds with the next customized setting.

6.2 Customize Cut Sheet TOF

1. After you follow through all the steps in 6.1 or you input “Next” in step 3 in 6.1, the printer prompts:

Top Margin

2. You may skip to other customized settings by pressing “Next” or “Back”. Once you press “OK” to continue with customization of cut sheet TOF, the printer prompts:

Press any key to eject current page, load paper in the Fanfold paper path, and then proceed as follows: [TOP] = -(1/72) inch, [LF] = +(1/72) inch, [LOAD/EJECT] = OK, [ONLINE] = Exit, [ONLINE] + [LOAD/EJECT] = Save and restart the printer.

3. Follow the given prompt to unload the Setup Instruction Page. Ensure the lever is at position. Then press the【Load/Eject】 key to load fanfold paper from tractors. The top edge of the form initially aligns with the printer’s tear-off blade. You may input +/- 1/72” to adjust the TOF position. When you get the desirable TOF, press OK or Exit. The printer prompts the customized TOF value:

The defined position is: 4.2 mm. Save the parameter settings ([LOAD/EJECT] or [ONLINE]=OK, [LF]=Next)?

Yes

Page 76

Tally Dascom 1330

4. At this stage: If 【Load/Eject】key is pressed, an asterisk “*” is appended to “Yes” and you should repeat the procedures for form length measurement as mentioned. Or, If you input “Exit”, the printer saves the measurement value and proceeds with the next customized setting.

6.3 Customize Cut Sheet Bottom Margin

1. After you follow through all the steps in 6.2 or you input “Next” twice in step 3 in 6.1, the printer prompts:

Bottom Margin

2. The remaining operations are nearly the same as described in section 6.2. The only difference is to input +/- 1/72” till you get the desirable bottom margin.

6.4 Customize Cut Sheet Left Margin

1. After you follow through all the steps in 6.3 or you input “Next” three times in step 3 in

6.1, the printer prompts:

Left Margin

2. The remaining operations are nearly the same as described in section 6.2. The only difference is to input +/- 1/72” till you get the desirable left margin.

6.5 Customize Fanfold Page Formatting Parameters

The customizations of the form length, TOF, bottom and left margins for fanfold are exactly the same as describe. All you need is to bypass the Single Sheet menu under Customize Form. Follow step 1 in section 6.1:

Customize Form

[LF]=Next, [TOP]=Back, [LOAD/EJECT]=OK, [ONLINE]=Exit, [ONLINE]+[LOAD/EJECT]= Save and restart the printer.

Single sheet

Then hit “Next” instead to get into the fanfold parameter menus:

[Tractor Paper]

Form Length

Refer section 6.1 to 6.4 for details on customizing the form length, TOF, bottom margin, and left margin for fanfold.

Page 77

Tally Dascom 1330

7 Maintenance

Your printer requires very little care. Occasional cleaning and replacement of the Ribbon Cartridge are all that is required. Cleaning is recommended approximately every 6 months or 300 hours of operation, whichever is sooner. Lubrication of the printer is not usually necessary. If the print head carriage does not move smoothly back and forth, clean the printer in the manner described in this chapter. If the problem continues, contact your dealer to determine whether lubrication may be necessary.

Switch printer off and unplug the Power Cord from the mains before

maintenance work.

7.1 Cleaning

The housing and the cover of the printer help protect it against dust, dirt, and other contaminants. However, paper produces small particles that accumulate inside the printer. This section explains how to clean and vacuum the printer and how to clean the paper bail rollers. It is easier to clean the printer when the cover is open.

7.2 Cleaning and Vacuuming the Printer

If the print head carriage does not move smoothly back and forth or paper particles have accumulated in the printer, clean the printer.

To clean and vacuum the printer:

1. Remove any paper from the printer. Make sure that the power is off, and then disconnect the printer Power Cord.

2. Using a soft vacuum brush, vacuum the exterior of the printer. Also vacuum the cut sheet edge.

3. Use a soft, damp cloth to wipe the exterior of the printer, including the cover. A mild detergent may be used. Do not use solvents, kerosene, or abrasive cleaning materials that may damage the printer.

4. Open the cover of the printer and remove the Ribbon Cartridge. Using a soft vacuum brush, gently vacuum the Platen, the print head carriage and shaft, and surrounding areas. You can easily slide the print head to the left or right when the power is off. Be careful not to press too hard on the flat head cable that extends from the print head carriage.

5. Re-install the Ribbon Cartridge.

6. Remove the single Sheet Feeder and clean the form tractors and the surrounding areas.

7. Re-install the single Sheet Feeder.

Page 78

Tally Dascom 1330

7.3 Cleaning the Paper Rollers

Clean the Platen and paper bail rollers occasionally or when stains or smudges appear on the paper. Use a mild detergent as appropriate. Do not use alcohol to clean the Platen or the rollers. Alcohol may cause the rubber to harden.

To clean the rollers and the Platen:

1. Apply a small amount of water to a soft cloth. Avoid spilling liquid inside the printer.

2. Place the cloth against the platen and manually rotate the Paper Feed Knob.

3. Repeat this procedure for each roller.

4. To dry the platen, place a dry cloth against the platen and the rollers and manually rotate the Paper Feed Knob.

Page 79

Tally Dascom 1330

8 Troubleshooting

Your printer is extremely reliable, but occasionally problems may occur. This chapter provides information on some of the common problems you may encounter and how you may solve them. If you encounter problems that you cannot resolve, contact your dealer or service partner for assistance.

8.1 Print Quality Problems and Solutions

Problem

Solution

Printing is too light or too dark.

 Make sure that the Ribbon Cartridge is properly

installed and that the ribbon feeds smoothly.

 Replace the ribbon if necessary.  Make sure that the print gap lever is set for the

thickness of your paper.

Smears and stains appear on the page.

 Make sure that the print gap lever is set for the

thickness of your paper.

 Check for ribbon wear. Replace the ribbon if

necessary.

 Check whether the tip of the print head is dirty. Clean

the head with a soft cloth if necessary.

 The print head may need to be replaced.

Printing is erratic or the wrong characters are printed. Many “?” or unexpected characters are printed.

 Make sure that the interface cable is securely

connected to both the printer and computer.

 Make sure that the printer driver selected in your

software is the same as the emulation selected on the printer.

 Check the length of the interface cable. (Maximum

Parallel & USB: 2 meters)

 Try another interface cable.  Make sure the International Character Set selected is

the correct one.

The page is blank.

 Make sure that the Ribbon Cartridge is properly

installed.

 Make sure the gap lever is set correctly.

Printing is vertically misaligned (jagged).

Use the printer's vertical alignment function to check the vertical print alignment. If necessary, adjust the print alignment.

The top margin is wrong.

 Check the application top margin setting.  Adjust the Top Margin setting in Page Setup menu if

necessary.

Page 80

Tally Dascom 1330

Problem

Solution

Lines are double spaced instead of single spaced.

Change the Auto LF setting in the System Setup menu to No.

The printer overprints on the same line.

Change the Auto CR setting in the System Setup menu to No.

The next print line starts where the previous line ended instead of at the left margin.

Change the Auto CR setting in the System Setup menu to Yes.

Some dots are missing.

 Use Change Pin function.  The print head may need to be replaced. Contact your

dealer.

8.2 Paper Handling Problems and Solutions

Problem

Solution

Paper cannot be loaded or fed.

 Make sure that the paper select lever located on the top

right of the printer is set correctly. Move the lever to the front for single sheets or to the rear for continuous forms.

 Make sure that the paper covers the paper-out sensor.

Paper jams while loading.

 Turn off the printer and remove the jammed paper.

Remove any obstructions from the paper path.

 Make sure that the Print Gap lever is set for the

thickness of your paper.

 Make sure that the paper is not folded, creased, or torn.  Make sure that the left and right tractors are set so that

the continuous forms are stretched taut.

Paper jams while printing.

 Turn off the printer and remove the jammed paper.

Remove any obstructions from the paper path.

 Make sure that the Print Gap lever is set for the

thickness of your paper.

 For continuous forms, make sure that the incoming and

outgoing paper stacks are correctly placed. Paper should feed straight.

Paper slips off the forms tractors or the perforated holes of the paper tear during printing.

Make sure that the forms tractors are positioned correctly for the width of your paper and that the perforated holes of the paper fit directly over the tractor pins.

Page 81

Tally Dascom 1330

8.3 Operating Problems and Solutions

Problem

Solution

The power does not turn on.

 Check whether the mains voltage is correct.  Make sure that the Power Cord is securely connected

to both the printer and the mains power outlet.

 Make sure that the power outlet is functional. If not so,

use other outlet.

 Turn the power off. Wait a minute and then turn the

printer on again. If the printer still has no power, contact your dealer.

The printer is on but it will not print.

 Make sure that the Online indicator is lit.  If you use the interface cable, make sure it is securely

connected to both the printer and the computer.

 Make sure paper is loaded.  Run the printer Status Page. If printing executes

normally, the problem is caused by: the interface, the computer, incorrect printer settings, or incorrect software settings.

 Make sure the printer driver selected in your software

is the same as the emulation selected on the printer.

Paper select lever error

If paper is loaded and the paper select lever is moved to the incorrect position, the printer turns offline, and the buzzer sounds continuously. Switch the paper select lever back to its correct position.

8.4 Printer Failures

A user cannot generally resolve a problem involving defective printer hardware. Power off and on again the printer to recover any fatal error. If the problem cannot be resolved, contact your dealer or service partner.

Page 82

Tally Dascom 1330

8.5 Error Indications on LEDs

Power LED

Paper

Exit LED

Speed

LED

Online

LED

Buzzer

Sound

EEPROM

Off

Flashing

None

Print Head temperature is too low

Flashing

Off

Flashing

None

Carriage initial position

Off

Flashing

Continuous

Raster reading trouble

Off

Flashing

Continuous

Front feed Sensor trouble

Off

Flashing

None

Paper width trouble

Off

Once

Paper jam

Flashing

No change

Once

Print Head too hot

Flashing

No change

Flashing

None

Paper path switching trouble

Flashing

No change

Flashing

Continuous

Paper end rear Sensor trouble

Off

None

Print Head temperature is too low

Flashing

Off

Flashing

None

Carriage initial position

Off

Flashing

Continuous

8.6 Diagnostic Functions

The printer diagnostic functions are Self-Test page, hex-dump mode and print alignment adjustment.

 Self-Test page: Tells you whether the printer hardware is functioning correctly. If the

printer hardware is functional, any problems you are having are probably caused by incorrect printer settings, incorrect software settings, the interface, or the computer.

 HEX-DUMP MODE: Allows you to determine whether the computer is sending the

correct commands to the printer, and whether the printer is executing the commands correctly. This function is useful to programmers or others who understand how to interpret hex dumps.

 PRINTING ALIGNMENT ADJUSTMENT: Allows you to check and, if necessary,

correct the printer’s vertical line print alignment in bi-directional mode.

8.7 Firmware Update

Sometimes it is necessary to update the firmware to solve a problem. The latest firmware file may be obtained from your dealer or downloaded from our website www.dascom.com. Before updating firmware, it is strongly recommended to print the Main Menu page to keep a record of the old settings.

Operation

Status Error

Description

Page 83

Tally Dascom 1330

Note: Firmware update should only be performed by an authorized service person. We disclaim any responsibility for any damage caused if it is performed by any other person.

To load new firmware, proceed as follows:

1. Switch off the printer. Connect your PC to the USB port on the printer.

2. Link Configuration Tool and then click “Firmware Update” as shown in below picture:

3. Click “Browse” to choose program file and character set. Then Click “Start” and following message is prompted. Click “OK”.

Page 84

Tally Dascom 1330

4. Enter download process and it is shown as below picture. In this process, L1 and L2 are on; And L3 and L4 are blinking.

5. When download is completed, the carriage returns to home position. Printer initializes normally.

Page 85

Tally Dascom 1330

9 General Specifications

Print System

Serial impact dot matrix

Print Technology

Uni-/bi-directional logic seeking for text and graphics (software selectable)

Print Speed

Pitch

DRAFT

NLQ

10 CPI

300 CPS

200 CPS

100 CPS

12 CPI

360 CPS

240 CPS

120 CPS

15 CPI

450 CPS

300 CPS

150 CPS

Print Head

Number of pins:

Life:

Pin diameter:

24 pins/ 12x2 staggered 400 million strokes/pin

0.2 mm

Font

Roman, Sans Serif, Courier, Prestige, Script, OCR-B,OCR-A, ORATOR,GOTHIC,SOUVENIR

Character Set

Standard character set I,Standard character set II IBM character set I,IBM character set II OCR-A character set I,OCR-A character set II OCR-B character set I,OC-B character set II International Character sets:15 country (see the note) Note:USA,France,Germany,UK,Denmark I,Sweden,Italy,Spain I,Japan, Norway,Denmark II,Spain II,Latin America,Denmark/Norway,China

Printable Columns

Characters per line (CPL) Pica (10 CPI) Elite(12 CPI) Micron(15 CPI) Condensed(17.1 CPI) Condensed Elite(20 CPI) Proportional

82 CPL 98 CPL 123 CPL 140 CPL 164 CPL changeable

Font Matrix

Character Pica Elite Super/Subscript Proportional Proportional super/subscript

Matrix(Draft)

Matrix(NLQ)

Matrix(LQ)

24*12 24*10 16*8

24*18 24*15 16*12

24*36 24*30 16*24 24*n 16*n

Page 86

Tally Dascom 1330

Graphics

Graphics Matrix 8*480(single density) 8*960(double density) 8*960(high speed double density*) 8*1920(quadruple density*) 8*640(CRT I) 8*720(CRT II) 24*480(single density) 24*960(double density) 24*720(CRT III) 24*1440(triple) 24*2880(sextuple*)

DPI 60 120 120 240 80 90 60 120 90 180 360

(note: the asterisk marks only printing one adjacent dot )

Line Spacing

1/6", 1/8", n/60", n/180", n/360"

Paper Specifications

Paper type: Single ply, Fanfold paper, Label, Cheque, Card and Envelope, Multilayer paper

Paper thickness: Maximum thickness is 1.0mm

Paper size:

Cut Sheet Width:55mm~297mm (2.2”~11.7”) Length:55mm~305mm (2.2”~12”)

Fanfold Paper Width:55m~290mm (2.2”~11.4”) Length:76mm~559mm (3”~22”)

Paper Feed method

Push tractor(Fanfold paper) Friction (Cut sheet)

Paper Feed Speed

8.0 IPS (inches per second)

Copy Capability

Original + 6 copy

Ribbon Type

Cartridge,monochrome/black

Ribbon Life

9 million characters at Draft/10 CPI

Buffer Capability

Up to 256KB

Interface

USB Options: Parallel, Ethernet10/100, WiFi (IEEE802.11 b, IEEE802.11g, IEEE802.11 n), Blue-tooth 3.0EDR Compliant, and serial

Noise Level

Approx. 57dB(A)

Ambient Conditions

Temperature Operating: +0 to +45 °C

Stand-by: -20 to +55 °C

Humidity Operating: 10 to 96%RH(No condensation)

Stand-by: 5 to 96%RH (No condensation)

MTBF

12,000 hours

MVBF

24 mil lines

Page 87

Tally Dascom 1330

Dimensions

395mm(L)×320mm (W)×205mm (H)

15.55″(L)×12.60″(W)×8.07″(H)

Weight

4.2kg

Power Supply

Voltage rating: AC220V~240V or AC100V~120V Frequency:50/60Hz (Power Supply is supplied according to different voltage of different regions)

Power consumption

Power Consumption:34W Power consumption for Sleep mode: 1.4W

Environmental Protection

Conform to HJ/T302-2006《Technical Requirements of Environmental protection product for Printer, Fax and Multi-function machine 》 Conform to requirements of Pollution Controlling and Management

Method of Electronic products.

Factory Optional Units

Parallel interface Network port WiFi Bluetooth Serial interface Feed form at optional position Black mark location

Certification

UL, CE, FCC ID, Energy Star, CB

Page 88

Tally Dascom 1330

10 Interface

10.1 Parallel Interface

Parallel Interface Pin Assignment

Signal Name

Signal Transmission

STROBE¯¯¯¯¯¯

Printer  Computer

2~9

DATA

Printer  Computer

ACK¯¯¯

Printer  Computer

BUSY

Printer  Computer

SELECT

Printer  Computer

AFXT¯¯¯¯

Printer  Computer

Unused

GND

Printer  Computer

F-GND

Printer  Computer

+5V

Printer  Computer

19~30

GND

Printer  Computer

INIT¯¯¯¯

Printer  Computer

FAULT¯¯¯¯¯

Printer  Computer

GND

Printer  Computer

Unused

FUSE

Printer  Computer

SLCTIN¯¯¯¯¯¯

Printer  Computer

Parallel Interface Connector Diagram

Any external devices connected to the parallel port should not draw current exceeding 200 mA from pin 18; otherwise it may affect the printer operation.

Page 89

Tally Dascom 1330

10.2 USB Interface

The USB interface conforms to the Universal Serial Bus 2.0 Specifications. It supports the Full Speed mode at 12 Mbps. It uses the “B” type USB connector.

10.3 Serial interface

Serial interface pin assignment

Serial interface connector diagram

Serial interface wiring diagram

Signal name

Description

RXD

Receive data

TXD

Send data

DTR

Data terminal ready

SGND

Signal ground

DSR

Data set ready

RTS

Request to send

CTS

Clear to send

Page 90

Tally Dascom 1330

Note:

1. The serial cable length should not exceed 15 meters.

2. Make sure the “Interface Setup” selects serial interface and the settings are the same as PC communication port settings. Shown as below:

Page 91

Tally Dascom 1330

11 Code Pages

11.1 Character Set

Standard character set 1

Standard character set 2

Page 92

Tally Dascom 1330

IBM character set 1

IBM character set 2

Page 93

Tally Dascom 1330

OCR-A character set 1

OCR-A character set 2

Page 94

Tally Dascom 1330

OCR-B character set 1

OCR-B character set 2

Page 95

Tally Dascom 1330

International Character Set Commands

Country

Basic Command

USA

＜ESC＞“R”CHR＄(0)

FRANCE

＜ESC＞“R”CHR＄(1)

GERMANY

＜ESC＞“R”CHR＄(2)

＜ESC＞“R”CHR＄(3)

DENMARK 1

＜ESC＞“R”CHR＄(4)

SWEDEN

＜ESC＞“R”CHR＄(5)

ITALY

＜ESC＞“R”CHR＄(6)

SPAIN 1

＜ESC＞“R”CHR＄(7)

JAPAN

＜ESC＞“R”CHR＄(8)

NORWAY

＜ESC＞“R”CHR＄(9)

DENMARK 2

＜ESC＞“R”CHR＄(10)

SPAIN 2

＜ESC＞“R”CHR＄(11)

LATINAMERICA

＜ESC＞“R”CHR＄(12)

DENMARK/NORWAY

＜ESC＞“R”CHR＄(13)

CHINA

＜ESC＞“R”CHR＄(16)

International character sets：

Page 96

Tally Dascom 1330

11.2 Code Page Commands

Code Page

ESC R Parameter

ISO_ 8859-1

ISO_ 8859_1SAP

ISO_ 8859_2

ISO_ 8859_5

ISO_ 8859_7

ISO_ 8859_9

ISO_ 8859_15

CRO_ASCII

UK_ASCII

US_ASCII

Greek DEC

Swedish

German

Portuguese

Roman_8

Coax_Twinax

French

Italian

Spanish

Norwegian

ELOT_928

BRASCII

Abicomp

Table_1250

Table_1251

Table_1252

Table_1253

Table_1254

Table_437

NEW_437

Table_850

New_Dig_850

Table_860

Table_863

Table_865

Table_852

Table_851

Table_864

Table_857

Table_866

Kamenicky

Mazovia

Table_737

Page 97

Tally Dascom 1330

Code Page

ESC R Parameter

Table_861

Extended_864

Farsi

Urdu

Old_Code_860

Flarro_863

Table_865

Siemens Turkish

DEC_Turkish

Bulgaria_866

Table_858

11.3 Code Page Tables

CP_437

Page 98

Tally Dascom 1330

CP_737

CP_850

Page 99

Tally Dascom 1330

CP_851

CP_852

Page 100

Tally Dascom 1330

CP_857

CP_858

Dascom 1330 User Manual

Specifications and Main Features

Frequently Asked Questions

User Manual