Daikin EHBH04DA6V7, EHBH08DA6V7, EHBH08DA9W7, EHBX04DA6V7, EHBX08DA6V7 Installation manuals

Installation manual

Daikin Altherma 3 R W

EHBH04DA6V7
EHBH08DA6V7
EHBH08DA9W7

EHBX04DA6V7
EHBX08DA6V7
EHBX08DA9W7

Installation manual

Daikin Altherma 3 R W

English

Directivelor, cu amendamentele respective.

<A>

<B>

<C>

DEKRA (NB0344)

2192529.0551-EMC

DAIKIN.TCF.034A10/05-2020

Direktive z vsemi spremembami.

Direktiivid koos muudatustega.

Директиви, с техните изменения.

Direktyvose su papildymais.

Direktīvās un to papildinājumos.

Smernice, v platnom znení.

18192021222324

Direktiver, med senere ændringer.

Direktiv, med företagna ändringar.

Direktiver, med foretatte endringer.

10111213141516

Directives, as amended.

Direktiven, gemäß Änderung.

deklaruje na własną i wyłączną odpowiedzialność, że urządzenia, których ta deklaracja dotyczy:

declară pe proprie răspundere că echipamentele la care se referă această declaraţie:

z vso odgovornostjo izjavlja, da je oprema naprav, na katero se izjava nanaša:

kinnitab oma täielikul vastutusel, et käesoleva deklaratsiooni alla kuuluv varustus:

декларира на своя отговорност, че оборудването, за коeто се отнася тази декларация:

visiška savo atsakomybe skelbia, kad įranga, kuriai taikoma ši deklaracija:

ar pilnu atbildību apliecina, ka tālāk aprakstītās iekārtas, uz kurām attiecas šī deklarācija:

vyhlasuje na vlastnú zodpovednosť, že zariadenie, na ktoré sa vzťahuje toto vyhlásenie:

tamamen kendi sorumluluǧunda olmak üzere bu bildirinin ilgili olduǧu donanımının aşaǧıdaki gibi olduǧunu beyan eder:

17

18

19

20

21

22

23

24

25

megfelelnek az alábbi szabvány(ok)nak vagy egyéb irányadó dokumentum(ok)nak, ha azokat előírás szerint használják:

spełniają wymogi następujących norm i innych dokumentów normalizacyjnych, pod warunkiem że używane są zgodnie z naszymi instrukcjami:

sunt în conformitate cu următorul (următoarele) standard(e) sau alt(e) document(e) normativ(e), cu condiţia ca acestea să fie utilizate în conformitate cu

instrucţiunile noastre:

skladni z naslednjimi standardi in drugimi normativi, pod pogojem, da se uporabljajo v skladu z našimi navodili:

on vastavuses järgmis(t)e standardi(te)ga või teiste normatiivsete dokumentidega, kui neid kasutatakse vastavalt meie juhenditele:

съответстват на следните стандарти или други нормативни документи, при условие, че се използват съгласно нашите инструкции:

atitinka žemiau nurodytus standartus ir (arba) kitus norminius dokumentus su sąlyga, kad yra naudojami pagal mūsų nurodymus:

tad, ja lietoti atbilstoši ražotāja norādījumiem, atbilst sekojošiem standartiem un citiem normatīviem dokumentiem:

sú v zhode s nasledovnou(ými) normou(ami) alebo iným(i) normatívnym(i) dokumentom(ami), za predpokladu, že sa používajú v súlade snašim

návodom:

161718192021222324

ürünün, talimatlarımıza göre kullanılması koşuluyla aşağıdaki standartlar ve norm belirten belgelerle uyumludur:

25

Directives, telles que modifiées.

010203040506070809

Değiştirilmiş halleriyle Yönetmelikler.

25

Direktiivejä, sellaisina kuin ne ovat muutettuina.

v platném znění.

Smjernice, kako je izmijenjeno.

irányelv(ek) és módosításaik rendelkezéseit.

z późniejszymi poprawkami.

17

Richtlijnen, zoals geamendeerd.

Directivas, según lo enmendado.

Direttive, come da modifica.

Οδηγιών, όπως έχουν τροποποιηθεί.

Directivas, conforme alteração em.

както е изложено в <A> и оценено положително от <B>

съгласно Сертификата<C>.

kaip nustatyta <A> ir kaip teigiamai nuspręsta <B> pagal

Sertifikatą<C>.

kā norādīts <A> un atbilstoši <B> pozitīvajam vērtējumam

saskaņā ar sertifikātu<C>.

ako bolo uvedené v <A> a pozitívne zistené <B> vsúlade

s osvedčením<C>.

<A>’da belirtildiği gibi ve <C>Sertifikasına göre <B>

tarafından olumlu olarak değerlendirildiği gibi.

Директив со всеми поправками.

21Забележка*

22Pastaba*

23Piezīmes*

24Poznámka*

25Not*

a(z) <A> alapján, a(z) <B> igazolta a megfelelést, a(z)

<C>tanúsítvány szerint.

zgodnie z dokumentacją <A>, pozytywną

opinią <B> i Świadectwem<C>.

aşa cum este stabilit în <A> şi apreciat pozitiv de<B>

în conformitate cu Certificatul<C>.

kot je določeno v <A> in odobreno s strani <B>

vskladu scertifikatom<C>.

nagu on näidatud dokumendis <A> ja heaks kiidetud

<B> järgi vastavalt sertifikaadile<C>.

16Megjegyzés*

17Uwaga*

18Notă*

19Opomba*

20Märkus*

Low Voltage 2014/35/EU

enligt <A> och godkänts av <B> enligt

Certifikatet<C>.

som det fremkommer i <A> og gjennom positiv

bedømmelse av <B> ifølge Sertifikat<C>.

jotka on esitetty asiakirjassa <A> ja jotka <B>

on hyväksynyt Sertifikaatin<C> mukaisesti.

jak bylo uvedeno v <A> a pozitivně zjištěno

<B> vsouladu sosvědčením<C>.

kako je izloženo u <A> i pozitivno ocijenjeno odstrane

Electromagnetic Compatibility 2014/30/EU *

заявляет, исключительно под свою ответственность, что оборудование, к которому относится настоящее заявление:

erklærer under eneansvarlig, at udstyret, som er omfattet af denne erklæring:

deklarerar i egenskap av huvudansvarig, att utrustningen som berörs av denna deklaration innebär att:

erklærer et fullstendig ansvar for at det utstyr som berøres av denne deklarasjon innebærer at:

ilmoittaa yksinomaan omalla vastuullaan, että tämän ilmoituksen tarkoittamat laitteet:

prohlašuje ve své plné odpovědnosti, že zařízení, k němuž se toto prohlášení vztahuje:

izjavljuje pod isključivo vlastitom odgovornošću da oprema na koju se ova izjava odnosi:

teljes felelőssége tudatában kijelenti, hogy a berendezések, melyekre e nyilatkozat vonatkozik:

09

10

11

12

13

14

15

16

estão em conformidade com a(s) seguinte(s) norma(s) ou outro(s) documento(s) normativo(s), desde que estes sejam utilizados de

acordo com as nossas instruções:

соответствуют следующим стандартам или другим нормативным документам, при условии их использования согласно нашим инструкциям:

overholder følgende standard(er) eller andet/andre retningsgivende dokument(er), forudsat at disse anvendes i henhold til vore instrukser:

respektive utrustning är utförd i överensstämmelse med och följer följande standard(er) eller andra normgivande dokument, under förutsättning att

användning sker i överensstämmelse med våra instruktioner:

respektive utstyr er i overensstemmelse med følgende standard(er) eller andre normgivende dokument(er), under forutssetning av at disse brukes i

henhold til våre instrukser:

vastaavat seuraavien standardien ja muiden ohjeellisten dokumenttien vaatimuksia edellyttäen, että niitä käytetään ohjeidemme mukaisesti:

za předpokladu, že jsou využívány v souladu s našimi pokyny, odpovídají následujícím normám nebo normativním dokumentům:

08091011121314

u skladu sa slijedećim standardom(ima) ili drugim normativnim dokumentom(ima), uz uvjet da se oni koriste u skladu s našim uputama:

15

ob upoštevanju določb:

vastavalt nõuetele:

следвайки клаузите на:

laikantis nuostatų, pateikiamų:

ievērojot prasības, kas noteiktas:

19202122232425

održiavajúc ustanovenia:

11Information*

12Merk*

13Huom*

bunun koşullarına uygun olarak:

delineato nel <A> e giudicato positivamente da<B>

secondo il Certificato<C>.

όπως καθορίζεται στο <A> και κρίνεται θετικά

από το <B> σύμφωνα με το Πιστοποιητικό<C>.

tal como estabelecido em <A> e com o parecer positivo

<B> prema Certifikatu<C>.

14Poznámka*

15Napomena*

de <B> de acordo com o Certificado<C>.

как указано в <A> и в соответствии сположительным

решением <B> согласно Свидетельству<C>.

som anført i <A> og positivt vurderet af <B> ihenhold til

Certifikat<C>.

Hiromitsu Iwasaki

Director

Ostend, 2nd of June 2020

declares under its sole responsibility that the equipment to which this declaration relates:

erklärt auf seine alleinige Verantwortung daß die Ausrüstung für die diese Erklärung bestimmt ist:

déclare sous sa seule responsabilité que l'équipement visé par la présente déclaration:

CE - DECLARATION-OF-CONFORMITY CE - DECLARACION-DE-CONFORMIDAD CE - DECLARAÇÃO-DE-CONFORMIDADE CE - ERKLÆRING OM-SAMSVAR CE - IZJAVA-O-USKLAĐENOSTI CE - IZJAVA O SKLADNOSTI CE - ATITIKTIES-DEKLARACIJA

CE - KONFORMITÄTSERKLÄRUNG CE - DICHIARAZIONE-DI-CONFORMITA CE - ЗАЯВЛЕНИЕ-О-СООТВЕТСТВИИ CE - ILMOITUS-YHDENMUKAISUUDESTA CE - MEGFELELŐSÉGI-NYILATKOZAT CE - VASTAVUSDEKLARATSIOON CE - ATBILSTĪBAS-DEKLARĀCIJA

CE - DECLARATION-DE-CONFORMITE CE - ΔHΛΩΣΗ ΣΥΜΜΟΡΦΩΣΗΣ CE - OVERENSSTEMMELSESERKLÆRING CE - PROHLÁŠENÍ-O-SHODĚ CE - DEKLARACJA-ZGODNOŚCI CE - ДЕКЛАРАЦИЯ-ЗА-СЪОТВЕТСТВИЕ CE - VYHLÁSENIE-ZHODY

CE - CONFORMITEITSVERKLARING CE - FÖRSÄKRAN-OM-ÖVERENSTÄMMELSE CE - DECLARAŢIE-DE-CONFORMITATE CE - UYGUNLUK-BEYANI

verklaart hierbij op eigen exclusieve verantwoordelijkheid dat de apparatuur waarop deze verklaring betrekking heeft:

Daikin Europe N.V.

01

02

03

04

06Nota*

under iagttagelse af bestemmelserne i:

enligt villkoren i:

gitt i henhold til bestemmelsene i:

noudattaen määräyksiä:

za dodržení ustanovení předpisu:

prema odredbama:

követi a(z):

zgodnie z postanowieniami Dyrektyw:

101112131415161718

declara bajo su única responsabilidad que el equipo al que hace referencia la declaración:

dichiara sotto la propria responsabilità che gli apparecchi a cui è riferita questa dichiarazione:

δηλώνει με αποκλειστική της ευθύνη ότι ο εξοπλισμός στον οποίο αναφέρεται η παρούσα δήλωση:

declara sob sua exclusiva responsabilidade que os equipamentos a que esta declaração se refere:

EHBH04DA6V7, EHBX04DA6V7, EHBH08DA6V7,

05

06

07

EHBH08DA9W7, EHBX08DA6V7, EHBX08DA9W7,

08

are in conformity with the following standard(s) or other normative document(s), provided that these are used in accordance with our instructions:

der/den folgenden Norm(en) oder einem anderen Normdokument oder -dokumenten entspricht/entsprechen, unter der Voraussetzung, daß sie gemäß

unseren Anweisungen eingesetzt werden:

sont conformes à la/aux norme(s) ou autre(s) document(s) normatif(s), pour autant qu'ils soient utilisés conformément à nos instructions:

conform de volgende norm(en) of één of meer andere bindende documenten zijn, op voorwaarde dat ze worden gebruikt overeenkomstig onze

instructies:

están en conformidad con la(s) siguiente(s) norma(s) u otro(s) documento(s) normativo(s), siempre que sean utilizados de acuerdo con nuestras

instrucciones:

sono conformi al(i) seguente(i) standard(s) o altro(i) documento(i) a carattere normativo, a patto che vengano usati in conformità alle nostre istruzioni:

είναι σύμφωνα με το(α) ακόλουθο(α) πρότυπο(α) ή άλλο έγγραφο(α) κανονισμών, υπό την προϋπόθεση ότι χρησιμοποιούνται

01020304050607

σύμφωνα με τις οδηγίες μας:

following the provisions of:

gemäß den Vorschriften der:

conformément aux stipulations des:

EN60335-2-40,

overeenkomstig de bepalingen van:

010203040506070809

în urma prevederilor:

as set out in <A> and judged positively by <B>

siguiendo las disposiciones de:

secondo le prescrizioni per:

με τήρηση των διατάξεων των:

de acordo com o previsto em:

в соответствии с положениями:

01Note*

07Σημείωση*

08Nota*

according to the Certificate<C>.

wie in <A> aufgeführt und von <B> positiv

beurteilt gemäß Zertifikat<C>.

tel que défini dans <A> et évalué positivement par <B>

02Hinweis*

03Remarque*

09Примечание*

10Bemærk*

conformément au Certificat<C>.

zoals vermeld in <A> en positief beoordeeld door <B>

overeenkomstig Certificaat<C>.

como se establece en <A> y es valorado

positivamente por <B> de acuerdo con el

Certificado<C>.

04Bemerk*

05Nota*

3P507286-13C

Table of contents

Table of contents

1 About the documentation 3

1.1 About this document.................................................................. 3

2 About the box 4

2.1 Indoor unit ................................................................................. 4

2.1.1 To remove the accessories from the indoor unit......... 4

3 Preparation 4

3.1 Preparing the installation site .................................................... 4

3.1.1 Installation site requirements of the indoor unit .......... 4

3.2 Preparing water piping .............................................................. 6

3.2.1 To check the water volume and flow rate ................... 6

3.3 Preparing electrical wiring ......................................................... 6

3.3.1 Overview of electrical connections for external and

internal actuators ........................................................ 6

4 Installation 7

4.1 Opening the units ...................................................................... 7

4.1.1 To open the indoor unit............................................... 7

4.2 Mounting the indoor unit............................................................ 7

4.2.1 To install the indoor unit.............................................. 7

4.2.2 To connect the drain hose to the drain ....................... 8

4.3 Connecting refrigerant piping .................................................... 8

4.3.1 To connect the refrigerant piping to the indoor unit .... 8

4.4 Connecting water piping............................................................ 9

4.4.1 To connect the water piping........................................ 9

4.4.2 To fill the water circuit ................................................. 9

4.4.3 To fill the domestic hot water tank .............................. 9

4.4.4 To insulate the water piping........................................ 9

4.5 Connecting the electrical wiring................................................. 9

4.5.1 About electrical compliance ........................................ 9

4.5.2 To connect the electrical wiring to the indoor unit....... 9

4.5.3 To connect the main power supply ............................. 10

4.5.4 To connect the backup heater power supply .............. 10

4.5.5 To connect the shut-off valve...................................... 12

4.5.6 To connect the electricity meters ................................ 12

4.5.7 To connect the domestic hot water pump................... 12

4.5.8 To connect the alarm output ....................................... 12

4.5.9 To connect the space cooling/heating ON/OFF

output .......................................................................... 12

4.5.10 To connect the changeover to external heat source... 13

4.5.11 To connect the power consumption digital inputs....... 13

4.5.12 To connect the safety thermostat (normally closed

contact) ....................................................................... 13

4.6 Finishing the indoor unit installation .......................................... 13

4.6.1 To close the indoor unit............................................... 13

5 Configuration 14

5.1 Overview: Configuration ............................................................ 14

5.1.1 To access the most used commands ......................... 14

5.2 Configuration wizard.................................................................. 15

5.2.1 Configuration wizard: Language ................................. 15

5.2.2 Configuration wizard: Time and date .......................... 15

5.2.3 Configuration wizard: System ..................................... 15

5.2.4 Configuration wizard: Backup heater.......................... 16

5.2.5 Configuration wizard: Main zone................................. 17

5.2.6 Configuration wizard: Additional zone......................... 17

5.2.7 Detailed screen with weather-dependent curve.......... 18

5.2.8 Configuration wizard: Tank ......................................... 19

5.3 Settings menu ........................................................................... 20

5.3.1 Main zone ................................................................... 20

5.3.2 Additional zone ........................................................... 20

5.3.3 Information.................................................................. 20

5.4 Menu structure: Overview installer settings............................... 21

6.2 Checklist during commissioning ................................................. 22

6.2.1 To check the minimum flow rate .................................. 22

6.2.2 To perform an air purge ............................................... 22

6.2.3 To perform an operation test run ................................. 23

6.2.4 To perform an actuator test run ................................... 23

6.2.5 To perform an underfloor heating screed dryout.......... 23

7 Hand-over to the user 24
8 Technical data 25

8.1 Piping diagram: Indoor unit ........................................................ 25

8.2 Wiring diagram: Indoor unit ........................................................ 26

8.3 Table 1 – Maximum refrigerant charge allowed in a room:

indoor unit................................................................................... 29

8.4 Table 2 – Minimum floor area: indoor unit.................................. 29

8.5 Table 3 – Minimum venting opening area for natural

ventilation: indoor unit ................................................................ 29

1 About the documentation

1.1 About this document

Target audience

Authorised installers

Documentation set

This document is part of a documentation set. The complete set
consists of:

▪ General safety precautions:

▪ Safety instructions that you must read before installing

▪ Format: Paper (in the box of the indoor unit)

▪ Indoor unit installation manual:

▪ Installation instructions

▪ Format: Paper (in the box of the indoor unit)

▪ Outdoor unit installation manual:

▪ Installation instructions

▪ Format: Paper (in the box of the outdoor unit)

▪ Installer reference guide:

▪ Preparation of the installation, good practices, reference data,…

▪ Format: Digital files on http://www.daikineurope.com/support-

and-manuals/product-information/

▪ Addendum book for optional equipment:

▪ Additional info about how to install optional equipment

▪ Format: Paper (in the box of the indoor unit) + Digital files on

http://www.daikineurope.com/support-and-manuals/product­information/

Latest revisions of the supplied documentation may be available on
the regional Daikin website or via your dealer.

The original documentation is written in English. All other languages
are translations.

Technical engineering data

▪ A subset of the latest technical data is available on the regional

Daikin website (publicly accessible).

▪ The full set of latest technical data is available on the Daikin

Business Portal (authentication required).

6 Commissioning 22

6.1 Checklist before commissioning................................................ 22

EHBH/X04+08DA*V7
Daikin Altherma 3 R W
4P618951-1 – 2020.03

Installation manual

3

2 About the box

1× 1× 1× 1×

a b c d

2×4× 1×

fe g

1×

h

H≥1150

≥200

≥200

≥500

(mm)

≥450

2 About the box

2.1 Indoor unit

2.1.1 To remove the accessories from the indoor unit

Some accessories are located inside the unit. To open the unit, see

"4.1.1To open the indoor unit"[47].

H Height measured from the bottom of the casing to the floor

Special requirements for R32

WARNING

▪ Do NOT pierce or burn.

▪ Do NOT use means to accelerate the defrosting

process or to clean the equipment, other than those
recommended by the manufacturer.

▪ Be aware that R32 refrigerant does NOT contain an

odour.

a General safety precautions

b Addendum book for optional equipment

c Indoor unit installation manual

d Operation manual

e Sealing ring for shut-off valve

f Shut-off valve
g Overpressure bypass valve
h Wall bracket

3 Preparation

3.1 Preparing the installation site

WARNING

The appliance shall be stored in a room without
continuously operating ignition sources (example: open
flames, an operating gas appliance or an operating electric
heater).

WARNING

DO NOT reuse refrigerant piping that has been used with
any other refrigerant. Replace the refrigerant pipes or
clean thoroughly.

3.1.1 Installation site requirements of the indoor unit

▪ The indoor unit is designed for indoor installation only and for the

following ambient temperatures:

▪ Space heating operation: 5~30°C

▪ Space cooling operation: 5~35°C

▪ Domestic hot water production: 5~35°C

▪ Mind the following spacing installation guidelines:

WARNING

The appliance shall be stored so as to prevent mechanical
damage and in a well-ventilated room without continuously
operating ignition sources (example: open flames, an
operating gas appliance or an operating electric heater)
and have a room size as specified below.

NOTICE

▪ Do NOT re-use joints which have been used already.

▪ Joints made in installation between parts of refrigerant

system shall be accessible for maintenance purposes.

WARNING

Make sure installation, servicing, maintenance and repair
comply with instructions from Daikin and with applicable
legislation (for example national gas regulation) and are
executed only by authorised persons.

NOTICE

▪ Pipework shall be protected from physical damage.

▪ Installation of pipework shall be kept to a minimum.

Installation manual

4

EHBH/X04+08DA*V7
Daikin Altherma 3 R W
4P618951-1 – 2020.03

3 Preparation

Input from installer:

▪ Total refrigerant charge (m

c

) (kg)
▪ Installation height (H) (m)
▪ Area of room A (A

room A

) (m2)

Start

Use table 1 in chapter "Technical data" to
calculate the maximum refrigerant charge
(m

max

) (kg) allowed for room A.

Contact your dealer.

Use table 3 in chapter "Technical data" and
dm to calculate the minimum opening area for
natural ventilation between room A and

room B (VA

min

) (cm2).

Unit can be installed at room A if:
▪ 2 ventilation openings (permanently open) are provided between room A and B, 1 at the top and 1 at the bottom.
▪ Bottom opening: The bottom opening must meet the minimum area requirements (VA

min

). It must be as close as possible to the floor and lower than H. If the
ventilation opening starts from the floor, the height must be ≥20 mm. The bottom of the opening must be situated ≤100 mm from the floor. At least 50% of the
required opening area must be situated <200 mm from the floor. The entire area of the opening must be situated <300 mm from the floor.

▪ Top opening: The area of the top opening must be larger than or equal to the bottom opening. The bottom of the top opening must be situated at least 1.5 m

above the top of the bottom opening.

▪ Ventilation openings to the outside are NOT considered suitable ventilation openings (the user can block them when it is cold).

The unit can be installed in room A at the
specified installation height, and without
further room size or ventilation requirements.

Determine the refrigerant amount that exceeds

m

max

(dm) (kg). (dm=mc–m

max

)

m

max≥mc

?

Yes

No

No

Use table 2 in chapter "Technical data" to
calculate the total minimum floor area
(A

min total

) (m2) required for the total refrigerant

charge (m

c

) at the selected installation height

(H).

a Indoor unit
A Room where the indoor unit is installed.
B Room adjacent to room A.

A

min total≤Aroom A+Aroom B

?

Yes

Input from installer:

▪ Area of adjacent room B (A

room B

) (m2)

A

a

B

≥1.5 m

If the total refrigerant charge in the system is ≥1.84kg (i.e. if the piping length is ≥27m), you need to comply with the minimum floor area
requirements as described in the following flow chart. The flow chart uses the following tables: "8.3 Table 1 – Maximum refrigerant charge

allowed in a room: indoor unit"[429], "8.4Table 2 – Minimum floor area: indoor unit"[429] and "8.5Table 3 – Minimum venting opening area
for natural ventilation: indoor unit"[429].

INFORMATION

Systems with a total refrigerant charge (mc) <1.84kg (i.e. if
the piping length is <27 m) are NOT subjected to any
requirements to the installation room.

INFORMATION
Multiple indoor units. If two or more indoor units are

installed in a room, you must consider the maximum
refrigerant charge that can be released in the room when a
SINGLE leak occurs. Example: If two indoor units are
installed in the room, each with its own outdoor unit, then
you have to consider the refrigerant charge of the largest
indoor-outdoor combination.

EHBH/X04+08DA*V7
Daikin Altherma 3 R W
4P618951-1 – 2020.03

Installation manual

5

3 Preparation

3.2 Preparing water piping

NOTICE

In case of plastic pipes, make sure they are fully oxygen
diffusion tight according to DIN 4726. The diffusion of
oxygen into the piping can lead to excessive corrosion.

▪ Valve towards expansion vessel. The valve towards the

expansion vessel (if equipped) MUST be open.

3.2.1 To check the water volume and flow rate

Minimum water volume

Check that the total water volume in the installation is minimum
10litres, the internal water volume of the indoor unit NOT included.

NOTICE

When circulation in each space heating/cooling loop is
controlled by remotely controlled valves, it is important that
the minimum water volume is guaranteed, even if all of the
valves are closed.

Minimum flow rate

Check that the minimum flow rate in the installation is guaranteed in
all conditions. This minimum flow rate is required during defrost/
backup heater operation. For this purpose, use the overpressure
bypass valve delivered with the unit, and respect the minimum water
volume.

NOTICE

When circulation in each or certain space heating loops is
controlled by remotely controlled valves, it is important that
the minimum flow rate is guaranteed, even if all valves are
closed. In case the minimum flow rate cannot be reached,
a flow error 7H will be generated (no heating or operation).

See the installer reference guide for more information.

Minimum required flow rate

12l/min

See the recommended procedure as described in "6.2 Checklist

during commissioning"[422].

3.3 Preparing electrical wiring

3.3.1 Overview of electrical connections for external and internal actuators

Item Description Wires Maximum

running

current

Outdoor unit and indoor unit power supply

1 Power supply for

2+GND

outdoor unit

2 Power supply and

3
interconnection cable to
indoor unit

3 Power supply for

See table below. —
backup heater

4 Preferential kWh rate

2
power supply (voltage
free contact)

5 Normal kWh rate power

2 6.3A
supply

Optional equipment

6 3‑way valve 3 100mA

(a)

(g)

(e)

(b)

Item Description Wires Maximum

running

current

7 Power supply for

4+GND

(c)

booster heater and
thermal protection
(from indoor unit)

8 Power supply for

2+GND 13A
booster heater (to
indoor unit)

9 Domestic hot water

2

(d)

tank thermistor

10 User interface used as

2

(f)

room thermostat

11 Room thermostat 3 or 4 100mA
12 Outdoor ambient

2

(b)

temperature sensor

13 Indoor ambient

2

(b)

temperature sensor

14 Heat pump convector 2 100mA

Field supplied components

15 Shut-off valve 2 100mA
16 Electricity meter 2 (per meter)
17 Domestic hot water

2

(b)

(b)

pump

18 Alarm output 2
19 Changeover to external

2

(b)

(b)

heat source control

20 Space cool/heat

2

(b)

operation control

21 Power consumption

digital inputs

22 Safety thermostat 2

(a) Refer to name plate on outdoor unit.
(b) Minimum cable section 0.75mm².
(c) Cable section 2.5mm².
(d) The thermistor and connection wire (12m) are delivered

with the domestic hot water tank.

(e) Cable section 0.75mm² till 1.25mm²; maximum length:

50m. Voltage-free contact shall ensure the minimum
applicable load of 15VDC, 10mA.

(f) Cable section 0.75mm² till 1.25mm²; maximum length:

500m. Applicable for both single user interface and dual
user interface connection.

(g) Cable section 1.5mm².

2 (per input

signal)

(b)

(e)

NOTICE

More technical specifications of the different connections
are indicated on the inside of the indoor unit.

Backup heater

type

Power supply Required number of

conductors

*6V 1N~ 230V (6V) 2+GND

3~ 230V (6T1) 3+GND

*9W 3N~ 400V 4+GND

(b)

(b)

(b)

Installation manual

6

EHBH/X04+08DA*V7
Daikin Altherma 3 R W
4P618951-1 – 2020.03

4 Installation

1

2

3

1

4

4

2

2

1

3

4×

2×

1

2

1

2

3

2×

3

1

2

4.1 Opening the units

4.1.1 To open the indoor unit

Overview

1 Front panel
2 Switch box cover
3 Switch box
4 User interface panel

Open

1 Remove the front panel.

4 Installation

4 If you have to do work behind the user interface panel or upload

new software into the user interface, open the user interface
panel.

5 Optional: Remove the user interface panel.

NOTICE

If you remove the user interface panel, also disconnect the
cables from the back of the user interface panel to prevent
damage.

2 If you have to connect electrical wiring, remove the switch box

cover.

4.2 Mounting the indoor unit

3 If you have to do work behind the switch box, open the switch

box.

4.2.1 To install the indoor unit

1 Fix the wall bracket (accessory) to the wall (level) with 2 Ø8mm

bolts.

EHBH/X04+08DA*V7
Daikin Altherma 3 R W
4P618951-1 – 2020.03

Installation manual

7

4 Installation

2×

a

42 kg

a

ab

a Optional: If you want to fix the unit to the wall from inside

the unit, provide an additional screw plug.

2 Lift the unit.

4.2.2 To connect the drain hose to the drain

Water coming from the pressure relief valve is collected in the drain
pan. You must connect the drain pan to an appropriate drain
according to the applicable legislation.

1 Connect a drain tube (field supply) to the drain pan connector

as follows:

3 Attach the unit to the wall bracket:

▪ Tilt the top of the unit against the wall at the position of the

wall bracket.

▪ Slide the bracket on the back of the unit over the wall

bracket. Make sure the unit is fixed properly.

4 Optional: If you want to fix the unit to the wall from inside the

unit:

▪ Remove the upper front panel, and open the switch box. See

"4.1.1To open the indoor unit"[47].

▪ Fix the unit to the wall with an Ø8mm screw.

a Drain pan connector

It is recommended to use a tundish to collect the water.

4.3 Connecting refrigerant piping

See the installation manual of the outdoor unit for all guidelines,
specifications and installation instructions.

4.3.1 To connect the refrigerant piping to the indoor unit

1 Connect the liquid stop valve from the outdoor unit to the

refrigerant liquid connection of the indoor unit.

a Refrigerant liquid connection
b Refrigerant gas connection

2 Connect the gas stop valve from the outdoor unit to the

refrigerant gas connection of the indoor unit.

Installation manual

8

EHBH/X04+08DA*V7
Daikin Altherma 3 R W
4P618951-1 – 2020.03

4 Installation

ab

b

a

X2M X1M

X5M

d

b+ca

c

4.4 Connecting water piping

4.4.1 To connect the water piping

NOTICE

Do NOT use excessive force when connecting the piping.
Deformation of the piping can cause malfunctioning of the
unit.

To facilitate service and maintenance, 2 shut-off valves and 1
overpressure bypass valve are provided. Mount the shut-off valves
on the space heating water inlet and space heating water outlet. To
ensure the minimum flow rate (and prevent overpressure), install the
overpressure bypass valve on the space heating water outlet.

1 Install the shut-off valves on the water pipes.

INFORMATION

Make sure both air purge valves (one on the magnetic filter
and one on the backup heater) are open.

4.4.3 To fill the domestic hot water tank

See the installation manual of the domestic hot water tank.

4.4.4 To insulate the water piping

The piping in the complete water circuit MUST be insulated to
prevent condensation during cooling operation and reduction of the
heating and cooling capacity.

If the temperature is higher than 30°C and the humidity is higher
than RH 80%, the thickness of the insulation materials should be at
least 20 mm to prevent condensation on the surface of the
insulation.

4.5 Connecting the electrical wiring

DANGER: RISK OF ELECTROCUTION

WARNING

ALWAYS use multicore cable for power supply cables.

4.5.1 About electrical compliance

a Water inlet

b Water outlet

2 Screw the indoor unit nuts on the shut-off valves.
3 Connect the field piping on the shut-off valves.
4 In case of connection with the optional domestic hot water tank,

see the installation manual of the domestic hot water tank.

NOTICE

Install air purge valves at all local high points.

NOTICE

Overpressure bypass valve (delivered as accessory). We

recommend to install the overpressure bypass valve in the
space heating water circuit.

▪ Mind the minimum water volume when choosing the

installation location of the overpressure bypass valve
(at the indoor unit, or at the collector). See "3.2.1To

check the water volume and flow rate"[46].

▪ Mind the minimum flow rate when adjusting the

overpressure bypass valve setting. See "3.2.1 To

check the water volume and flow rate" [4 6] and
"6.2.1To check the minimum flow rate"[422].

NOTICE

In case an optional domestic hot water tank is installed: A
pressure relief valve (field supply) with an opening
pressure of maximum 10bar (=1MPa) must be installed
on the domestic cold water inlet connection in accordance
with the applicable legislation.

Only for the backup heater of the indoor unit

See "4.5.4To connect the backup heater power supply"[410].

4.5.2 To connect the electrical wiring to the indoor unit

1 Open the switch box so that you can access the back of the

switch box. See "4.1.1To open the indoor unit"[47].

2 Route the wiring as follows:

▪ Enter the unit from the bottom.
▪ Route the wiring via the back of the switch box.
▪ Fix the cables with cable ties to the cable tie mountings at

the back of the switch box.

a, b, c Field wiring (see table below)

d Factory-mounted cable for power supply of backup heater

INFORMATION

When installing field supply or option cables, foresee
sufficient cable length. This will make it possible to open
the switch box and gain access to other components
during service.

4.4.2 To fill the water circuit

To fill the water circuit, use a field supply filling kit. Make sure you
comply with the applicable legislation.

EHBH/X04+08DA*V7
Daikin Altherma 3 R W
4P618951-1 – 2020.03

Installation manual

9

4 Installation

X2M

X1M

1 2 3

1 2 3

1 2 3

1 2 3

X1A

X11YB

X11YA X11Y

1 2 3

a

X5M

X2M

X1M

1 2 3

1 2

N L

N L3

S1S

a

bc

X11YA

X1A

X11YB X11Y

9 10

5

1 2 3

6

Routing Possible cables (depending on unit type

and installed options)

a

Low voltage

b

High voltage power
supply

c

High voltage control
signal

d

High voltage power
supply (factory­mounted cable)

CAUTION

Do NOT push or place redundant cable length in the unit.

4.5.3 To connect the main power supply

1 Connect the main power supply.

In case of normal kWh rate power supply

▪ Preferential power supply contact

▪ User interface used as room thermostat

(option)

▪ Power consumption digital inputs (field

supply)

▪ Outdoor ambient temperature sensor

(option)

▪ Indoor ambient temperature sensor

(option)

▪ Electrical meters (field supply)

▪ Safety thermostat (field supply)
▪ Interconnection cable

▪ Normal kWh rate power supply

▪ Preferential kWh rate power supply
▪ Heat pump convector (option)

▪ Room thermostat (option)

▪ Shut-off valve (field supply)

▪ Domestic hot water pump (field supply)

▪ Alarm output

▪ Changeover to external heat source

control

▪ Space cool/heat operation control
▪ Power supply for backup heater

a Interconnection cable (=main power supply)
b Normal kWh rate power supply
c Preferential power supply contact

2 Fix the cables with cable ties to the cable tie mountings.

INFORMATION

In case of preferential kWh rate power supply, connect
X11Y to X11YB. The necessity of separate normal kWh
rate power supply to indoor unit (b) X2M/5+6 depends on
the type of preferential kWh rate power supply.

Separate connection to the indoor unit is required:

▪ if preferential kWh rate power supply is interrupted

when active, OR

▪ if no power consumption of the indoor unit is allowed at

the preferential kWh rate power supply when active.

INFORMATION

The preferential kWh rate power supply contact is
connected to the same terminals (X5M/9+10) as the safety
thermostat. Thus, the system can have EITHER
preferential kWh rate power supply OR a safety
thermostat.

a Interconnection cable (=main power supply)

In case of preferential kWh rate power supply

Connect X11Y to X11YB.

Installation manual

10

4.5.4 To connect the backup heater power supply

CAUTION

If the indoor unit has a tank with a built‑in electrical booster
heater, use a dedicated power circuit for the backup heater
and booster heater. NEVER use a power circuit shared by
another appliance. This power circuit must be protected
with the required safety devices according to the applicable
legislation.

CAUTION

To guarantee the unit is completely earthed, always
connect the backup heater power supply and the earth
cable.

The backup heater capacity can vary, depending on the indoor unit
model. Make sure that the power supply is in accordance with the
backup heater capacity, as listed in the table below.

EHBH/X04+08DA*V7
Daikin Altherma 3 R W
4P618951-1 – 2020.03