TUNER AY---------------------------------------- J4 - 1
REMOVAL AND INSTALLATION -------- J4 - 1
SPEAKER(FRONT SPEAKER) ------------- J4 - 3
REMOVAL AND INSTALLATION -------- J4 - 3
SPEAKER(REAR SPEAKER) --------------- J4 - 4
REMOVAL AND INSTALLATION -------- J4 - 4
ANTENNA ---------------------------------------- J4 - 5
REMOVAL AND INSTALLATION -------- J4 - 5
J4 AUDIO & VISUAL SYSTEM
J4
TO INDEX
1 TUNER AY
1-1 REMOVAL AND INSTALLATION
1-1-1 OPERATION BEFORE REMOVAL
1.Remove the lower instrument panel finish panel S/A.
Refer to Page I2-23.
2.Remove the lower center instrument cluster finish panel S/A.
Refer to Page I2-23.
3.Move the heater control Ay until the bolts (2pcs) securing the stereo component tuner Ay can be
removed.
Refer to Page K1-7.
1-1-2 REMOVAL AND INSTALLATION PROCEDURES
(1) Components
(2) Removal and installation procedures
1-1-3 POINTS OF REMOVAL
(1) Tuner Ay, stereo component
1.The tuner Ay is secured on the center instrument cluster finish panel S/A by screws (4pcs). First remove
the whole panel S/A from the vehicle. Then remove the screws (4pcs) to remove the tuner Ay.
1 a Panel S/A, instrument cluster finish, center
j 2 b Tuner Ay, stereo component
3 c Bracket, radio receiver A
4 d Bracket, radio receiver B
b
S
S
S
S
B
B
S
a
c
d
T11H7001S25
J4–1
1-1-4 OPERATION AFTER INSTALLATION
1.Reinstall the heater control Ay.
Refer to Page K1-7.
2.Install the lower center instruent cluster finish panel S/A.
Refer to Page I2-23.
3.Install the lower instruent panel finish panel S/A.
Refer to Page I2-23.
J4–2
2 SPEAKER(FRONT SPEAKER)
2-1 REMOVAL AND INSTALLATION
2-1-1 OPERATION BEFORE REMOVAL
1.Remove the RH/LH speaker grille.
Refer to Page I2-23.
2-1-2 REMOVAL AND INSTALLATION PROCEDURES
(1) Components
(2) Removal and installation procedures
2-1-3 OPERATION AFTER INSTALLATION
1.Install the RH/LH speaker grille.
Refer to Page I2-23.
1 a Speaker Ay, radio (RH/LH)
T11H7002S16
a
S
S
J4–3
3 SPEAKER(REAR SPEAKER)
3-1 REMOVAL AND INSTALLATION
3-1-1 OPERATION BEFORE REMOVAL
1.Remove the lower RH/LH rear door trim board Ay.
Refer to Page I1-15.
3-1-2 REMOVAL AND INSTALLATION PROCEDURES
(1) Components
(2) Removal and installation procedures
3-1-3 OPERATION AFTER INSTALLATION
1.Install the lower RH/LH rear door trim board Ay.
Refer to Page I1-15.
1 a Speaker Ay, radio (RH/LH)
C11H5042S16
S
S
S
a
J4–4
4 ANTENNA
4-1 REMOVAL AND INSTALLATION
4-1-1 ARTICLES TO BE PREPARED
Instrument
4-1-2 OPERATION BEFORE REMOVAL
1.Remove the roof head lining Ay.
Refer to Page I2-53.
4-1-3 REMOVAL AND INSTALLATION PROCEDURES
(1) Components
Unit:N;m{kgf;cm}
(2) Removal and installation procedures
4-1-4 POINTS OF INSTALLATION
(1) Nut, antenna
1.Place a lead along the U-shaped slot of the antenna Ay
amplifier. Place the nut in the direction of the lead, and
tighten it to the specified torque.
TIGHTENING TORQUE: 4.5&1.0N;m {46&10kgf;cm}
i 1 a Nut, antenna
2 b Antenna Ay, amplifier
3 c Rod, antenna
c
b
a
T:4.5&1.0 {46&10}
T11H7501S20
Torque wrench
J4–5
T11H7010ET10
Lead wire
4-1-5 OPERATION AFTER INSTALLATION
1.Install the roof head lining Ay.
Refer to Page I2-53.
J4–6
TO INDEX TO NEXT SECTION
Loading...