INSTRUCTION MANUAL
TABLE OF CONTENTS |
|
■ SAFETY INSTRUCTION & |
|
SPECIFICATIONS ...................................... |
2 |
■ PARTS DESCRIPTIONS ............................ |
3 |
■ DIRECTIONS FOR SAFE USE.................. |
4 |
•How To Install ............................................ |
4 |
•Water Connection...................................... |
6 |
•Drain Hose Setting .................................... |
7 |
■ HOW TO OPERATE ................................... |
8 |
•Preparation for Washing............................ |
8 |
•Descriptions of Control Panel.................... |
9 |
•General Procedures for Operation.......... |
10 |
•Guides for Basic Washing Programs ...... |
11 |
•Guides for Other Useful Programs ......... |
13 |
■ PERIODIC MAINTENANCE..................... |
14 |
■ SPECIAL GUIDES FOR REMOVING STAINS... |
16 |
■ TROUBLE SHOOTING GUIDES ............. |
17 |
*PLEASE READ CAREFULLY THIS INSTRUCTION MANUAL BEFORE USING YOUR WASHER AND SAVE THIS FOR FUTURE REFERENCE.
Model: DWF-5510P
DWF-6021P
SAFETY INSTRUCTIONS & SPECIFICATIONS
SAFETY INSTRUCTIONS
Your safety is important to us.
Read all instructions before using your washer.
Do not wash items cleaned, washed, soaked in, or spotted with wax, paint, gasoline, oil, or other flammable fluids. The fumes can create a fire hazard or explosion.
Flammable fluids (dry-cleaning solvents, kerosene, gasoline, etc.) should not be used or stored in or near your washer. Do not add flammable fluids to your wash water. These substances give off vapors that can create a fire hazard or explosion.
Do not allow children to operate, play with, or crawl on or inside your washer. Supervise children closely when your washer is used near them.
Do not reach into the wash tub unless START/HOLD button is pressed and all motion stops, while spinning.
Do not use chlorine bleach and ammonia or acids (such as vinegar or rust remover) in the same wash. Hazardous fumes can form.
Unplug power supply cord before attempting to service your washer.
Do not pour water on the control panel.
Remove foreign objects (such as coin, pin, knife, other metallic materials, etc.) inside your wash load. They may damage any fabric.
Do not overload your washer to avoid poor cleaning, wrinkling and/or any abnormal operation.
SPECIFICATIONS
MODEL NO |
DWF-5510P |
|
DWF-6021P |
Power Source |
Please refer to the rating label at the back of your washer |
||
Power Consumption |
|
250W |
|
Width X Depth (mm) |
|
532X542 |
|
Height (mm) |
855 |
|
952 |
Net Weight (Kg) |
32 |
|
33.5 |
Maximum Mass of Textile |
5.5kg |
|
6.0kg |
Material of Internal Tub |
Recyclable Poly Propylene |
|
Anti-Rust Stainless Steel |
Water Consumption |
Approx. 135 Liters/Cycle |
|
Approx. 130 Liters/Cycle |
Washing Capacity |
Please refer to the rating label at the back of your washer. |
||
Washing Program |
|
4 Programs |
|
Water Level |
High (55 Liters), Medium (45 Liters), Low (31 Liters) |
||
Direction of Inlet Valve |
Backward |
|
Upward |
Operating Water Pressure |
0.3Kgf/cm2~8Kgf/cm2 (2.94N/cm2~78.4N/cm2) |
||
Pulsator |
Provided with 6 Spouting Holes for Powerful Upward Water Stream |
||
Coin Filter |
Only in Pump Model identified with ‘P’ added to Model No. (e.g., DWF-5510NP) |
||
|
|
|
|
The above specifications and features are subject to change without prior notice.
2
PARTS DESCRIPTIONS
DETERGENT CASE |
WATER CONNECTOR |
|
(Symbol ) |
(Blue Color : Cold, |
|
|
Pink Color : Hot) |
|
FABRIC SOFTNER INLET |
DOOR |
|
DRAIN HOSE |
||
(Symbol, See page 10) |
||
LIQUID BLEACH INLET |
|
|
(Symbol See page 10) |
LINT FILTER |
|
CONTROL PANEL |
||
|
||
(88 display and some |
|
|
buttons may be excluded) |
PLUG |
|
|
||
WASH TUB |
|
|
|
GROUND WIRE |
|
|
(This will not be |
|
|
provided in |
|
|
case of 3-wire |
|
PULSATOR |
power cord) |
|
|
||
BASE |
|
|
(Height is optional) |
|
|
|
ADJUSTABLE LEG |
|
|
(Optional) |
The drawings in this book may vary from your washer model. They are designed to show the different features of all models covered by this book. Your model may not include all features.
ACCESSORIES
Hose Adapter |
Under Cover(option) |
Hose Clamp |
|
UP |
|
In case of screw-shaped inlet hoses |
|
|
water tap adapters will not be provided. |
|
|
Drain Hose |
Inlet Hose(option) |
|
3
DIRECTIONS FOR SAFE USE
HOW TO INSTALL
Location
Place your washer on a level and solid floor, Considering the length of inlet hose, drain hose and power supply cord.
Do not place or store your washer below 0˚C(32˚F) to avoid any damage from freezing.
Do not place your washer where it may be splashed during bathing.
If washer is not level, it should be corrected by the adjustable leg (provided optionally) in the front-right side under the base and/or, a thin block or brick.
NOTES:
The opening muse not be obstructed by carpeting when the washing machine is installed on a carpeted floor.
Installation of the Under Base Cover(Option)
-DWF-5510P
After installing the washing machine, assemble the under-base cover.
1 Before installing your washer, remove the pad from the bottom of the cabinet. Then, separate under cover from rear side of cabinet by unscrewing and insert it into the base.
2 Push the under-base cover into the end, which decrease the noise made by this washer.
SCREW
-DWF-6021P
After the packing box is opened, there is a |
Push the under-base cover into the end, |
||||
1 under-base cover at the top of the washer. |
2 which decrease the noise made by this |
||||
|
washer. |
||||
|
|
|
|
|
|
|
|
|
|
|
|
4
Power Supply
•Before plugging the plug into wall receptacle, check the voltage rating is in the range of rating, marked on the label at the back side of your washer.
LABELSCREW
Grounding
•If your water tap or water pipe is not made of metal, connect the ground wire to a copper plate or a metal rod and bury it in the earth.
•If both your water tap and water pipe are made of metal, connect the ground wire to the base of the water tap.
•In case of using 3-core cord, there is no need for grounding.
|
• It is of no use connecting the |
20Cm |
ground wire to the water pipe |
|
made of plastic. |
Never Connect the Ground Wire to Such a Thing
•Never connect it to a gas pipe because of danger of a explosion.
•Never connect it to a telephone wire or a lightning rod because of os very dangerous at a thunderbolt.
Gas Pipe |
Telephone Wire |
5
WATER CONNECTION
Be careful not to confuse hot water inlet (pink color) and cold water inlet (blue color), if your washer is provided with dual water inlets.
Also if you have only one water tap, connect the inlet hose with cold water inlet (blue color).
For normal tap
1Pull down the collar of the |
2Loosen the four screws |
3Fit the hose adapter into the water |
|
inlet hose to separate it from |
properly in fitting into water |
tap and tighten the four screws |
|
the hose adapter. |
|
tap. |
evenly while pushing up the |
|
|
|
adapter so that the rubber packing |
|
|
|
can stick to the water tap tightly. |
|
|
|
TAPE |
4Remove the tape, and |
5Connect the inlet hose to |
6Connect the opposite end of |
|
screw connector B into |
the hose adapter, pulling |
the hose to water inlet of |
|
connector A tightly. |
|
down the collar of hose end. |
your washer tightly. |
|
|
|
• Please check the rubber |
|
|
|
packing is inside the hose |
|
|
|
end. |
connector A |
|
|
|
C |
A |
|
|
connector B |
|
|
|
C |
B |
|
|
In case that your washer is not provided with collar compartment, procedure 3 and 5 is not necessary.
For Thread-Fitting Type
1Connect the inlet
hose to the thread of water
tap or water pipe ConnectorConnectorD by tightening.
Rubber
Packing
2For the opposite end, connect it to water inlet as the above procedure 6.
InletHoseHose ConnectorC
Leak Test
Turn on the water completely to check for any leakage. If any leakage, turn off the water, try again as the above procedures.
For the special tap, call a qualified plumber for the installation.
6