Comelit 6701W Technical Manual

TECHNICAL

MANUAL

Mini

6701W 6701W/BM 6701W/8

Passion.Technology.Design.

Warning

Intended use

This Comelit product was designed for use in the creation of audio and video communication systems in residential, commercial or industrial settings and

in public buildings or buildings used by the public.

Installation

All activities connected to the installation of Comelit products must be carried out by qualiﬁed technical personnel, with careful observation of the

indications provided in the Manuals / Instruction sheets supplied with those products.

Wires

Cut o the power supply before carrying out any maintenance procedures.

Use wires with a cross-section suited to the distances involved, observing the instructions provided in the system manual.

We advise against running the system wires through the same duct as the power cables (230V or higher).

Safe usage

To ensure Comelit products are used safely:

• carefully observe the indications provided in the Manuals / Instruction sheets

• make sure the system created using Comelit products has not been tampered with / damaged.

Maintenance

Comelit products do not require maintenance aside from routine cleaning, which should be carried out in accordance with the indications provided in the

Manuals / Instruction sheets.

Any repair work must be carried out

• for the products themselves, exclusively by Comelit Group S.p.A.,

• for systems, by qualiﬁed technical personnel.

Disclaimer

Comelit Group S.p.A. does not assume any responsibility for

• any usage other than the intended use

• non-observance of the indications and warnings contained in this Manual / Instruction sheet.

Comelit Group S.p.A. nonetheless reserves the right to change the information provided in this Manual / Instruction sheet at any time and without prior

notice.

Table of contents

Description of the monitor .............................................................. 3

Description of buttons .............................................................................4

Indicator LED description........................................................................4

Technical characteristics ................................................................ 5

Installation ........................................................................................ 6

Removing / Fitting the terminal ..............................................................7

Connections ..................................................................................... 7

Monitor conﬁguration ..................................................................... 8

Main and secondary monitors ................................................................8

Power supply management .....................................................................8

6701W - 6701W/BM ...........................................................................8

6701W/8 .............................................................................................8

Button conﬁguration ....................................................................... 9

Basic conﬁguration ..................................................................................9

Legend ................................................................................................9

Advanced conﬁguration ........................................................................10

Intercom calls ....................................................................................10

Introduction ...............................................................................10

Internal general intercom call and external general intercom call:

button programming ..................................................................10

Intercom call to selective address: button programming .......... 11

Selective intercom address .......................................................11

Assigning a selective address to the monitor ............................11

Deleting the selective address of the monitor. ..........................11

Generic actuator, coded actuator .....................................................12

Generic actuator: button programming ....................................12

Coded actuator: button programming......................................12

Other functions: button programming ..............................................13

Programming range ..........................................................................13

Changing monitor ringtones .............................................................14

Programming reset ...........................................................................14

Addressing table ............................................................................ 15

System performance and layouts ................................................ 15

Description of the monitor

10.

11.

The monitor can be used in Simplebus2 audio/video systems.

• Art. 6701W is a colour monitor equipped as standard with 4 buttons.

• Art. 6701W/BM is a colour monitor equipped as standard with 4 buttons and magnetic induction (Hearing loop) system. Not

supplied with backplate 6710.

• Art. 6701W/8 is a colour monitor equipped as standard with 8 buttons.

CFP2

L CFP1

1. Brightness control

f To increase the value, turn clockwise

2. Colour intensity adjustment

f To increase the value, turn clockwise

3. 4.3" colour LCD screen

4. Call volume adjustment (High / Medium / Low)

5. Buttons

6. Handset

f Lift the handset to start communication

Do not press and hold the audio hook while the handset is lifted.

7. S1 Microswitches for programming the user code, see “Addressing table”

8. S2 Microswitches for button and function programming (marked with a red corner)

DIP 1-2-3-4 for button function programming

DIP 5-6 access to programming

DIP 7 for management of power supply voltage, see paragraph “Power supply management”

DIP 8

for main and secondary monitor setting, see paragraph “Main and secondary monitors”

9. Loudspeaker volume adjustment (for setting intercom audio only)

10. CV5 Jumper for video closure.

In systems with more than one monitor connected in cascade, only the monitor furthest away must have CV5 closed.

11. Pin for securing terminal block

Terminal block for system connection:

LL Bus line connection terminals

CFP1 CFP2 Floor door call input

Description of buttons

f Press the desired button once to activate the associated function.

Wait for approximately 1 sec. before pressing the same button again. Pressing the same button several times in quick succession will cancel the command.

LOCK-RELEASE

Use this key to open the corresponding door lock.

ACTUATOR default (programmable*)

Allows activation of the associated relay.

SELF ACTIVATION default (programmable*)

Allows activation of the external video unit, and therefore viewing of the external image.

SILENT MODE (Privacy)

The ringtone will be silenced on receipt of a call from the external unit and from the switchboard.

PROGRAMMABLE BUTTONS

Applies to monitor 6701W/8

(*) Buttons may be programmed as:

• DOOR OPENING UPON CALL (Doctor)

Allows automatic operation of the associated lock-release on receipt of a call from an external unit.

f To activate/deactivate Door opening upon call, press and hold the button programmed for this function.

• INTERCOM

Allows a call from one internal unit to one or more internal units.

• CALL TO A MAIN OR SECONDARY SWITCHBOARD

• PRIORITY CALL TO SWITCHBOARD (“PAN”)

• CALL TO CARETAKER DOOR-ENTRY PHONE

Indicator LED description

Flashing LED: incoming call

1 flash after pressing button: conﬁrms door opening

slow flashing: door open

FLASHING LED: device in programming mode

4 flashes: system engaged

Steady LED: Silent mode (Privacy) activated

3 flashes every 5 sec.: Door opening upon call function (Doctor) active

Technical characteristics

Product height (mm) 160 160 160

Product width (mm) 175 175 175

Product depth (mm) 22 22 22

Product weight (g) 600 600 600

Product color White RAL9003 White RAL9003 White RAL9003

Material ABS ABS ABS

Wall mounting Ye s Yes Yes

Desk base-mounted Ye s Yes Yes

Audio induction loop system No Yes No

LCD DISPLAY FEATURES

Size (inches) 4.3" 16/9 4.3" 16/9 4.3" 16/9

Resolution (pixel) 480x272 480x272 480x272

FUNCTIONS

Actuator control Yes (Default key 1) Yes (Default key 1) Yes (Default key 1)

Self Activation key Yes (Default key 2) Yes (Default key 2) Yes (Default key 2)

Switchboard call Ye s Yes Yes (Default key 3)

Priority call to switchboard Yes Yes Yes (Default key 5)

Intercom calls Yes Yes Yes

Multiple address call Ye s Yes Yes

Call divert Ye s Yes Yes

Silent mode (Privacy) Ye s Yes Yes

Door opening upon call (Doctor) Ye s Yes Yes (Default key 4)

Door open signaling Ye s Ye s Yes

6701W 6701W/BM 6701W/8

HARDWARE FEATURES

Type of buttons Capacitive Capacitive Capacitive

No. of programmable buttons for

additional functions

Removable terminals Ye s Yes Yes

SETTINGS

Ringtone volume Ye s Yes Yes

Screen brightness Ye s Yes Yes

Screen colour Ye s Yes Yes

ELECTRICAL CHARACTERISTICS

Type of power supply Power supply from

Supply voltage 22÷34 VDC (Bus) 22÷34 VDC (Bus) 22÷34 VDC (Bus)

Maximum absorption (W) 5.40 5.40 5.40

ENVIRONMENTAL AND COMPLIANCE

FEATURES

IP protection degree 30 30 30

Operating temperature (°C) 5÷40 5÷40 5÷40

Operating relative humidity (%) 25÷75 25÷75 25÷75

Environmental class I I I

Compliance and Certiﬁcations

2 2 6

Power supply from

video door entry bus

RoHS II - 2011/65/UE (EN 50581:2012), EMC 2014/30/UE (EN 61000-6-1:2007 , EN 61000-6-3:2007+A1:2011)

video door entry bus

Power supply from video door entry bus

+ 11 hidden pages