Note: Be sure to unfold this page and refer to the front diagrams as you read each chapter.
猔種: 綷弄各彻時叫叭ゲ甶秨此頁並綷弄玡面的瓜。
주: 반드시 이 페이지를 펴서 각 장을 읽을 때 앞면 도표를 참고하십시오.
2. CONTROLS / 北制 / 제어부
MAIN UNIT / 主诀 /메인유닛
With the FLIP DOWN PANEL opened / 讽 FLIP DOWN PANEL (陆秨面狾)砆
ゴ秨時 / 플립다운 패널이 열린 상태
English
いゅ
한국어
Note:
• Be sure to read this chapter referring to the front diagrams of chapter “2. CONTROLS” on page 3.
English
3. BUTTON TERMINOLOGY
4
DXZ466MP
Names of the Buttons and their Functions
[
OPEN] button
• Deeply push in [OPEN
]
button to unlock the flip
down panel.
[
ADJ] button
• Press the button to switch to the ADJ mode.
[
]
button
• Perform preset scan while in the radio mode.
Press and hold the button for 2 seconds or
longer to perform auto store.
• Play or pause a CD while in the CD/MP3/WMA
mode.
[
SENSOR
]
• Receiver for remote control unit.
• Operating range: 30° in all directions.
[
ISR] button
• Recall ISR radio station in memory.
• Press and hold for 2 seconds or longer: Store
current station into ISR memory (radio mode
only).
[D]
button
• Switch the display indication
(
Main display, Title
display).
• Press and hold the button for 1 second or longer
to enter the display adjustment mode.
[Z]
button
• Press the button to select one of the 3 types
of sound charact er istics already stored in
memory.
[T]
button
• Press the button to input a title in the Radio
mode.
• Press the button to input a title in the CD
mode.
• Press the button to switch the user titles or track
titles, while in the CD/MP3/WMA mode.
• Press the button to scroll the title during the CDtext play, while in the CD/MP3/WMA mode.
[
BND] button
• Switch the band, or seek tuning or manual tuning
while in the radio mode.
• Play a first track while in the CD/MP3/WMA
mode.
Press and hold the button for 1 second or longer
to perform multi-session.
• Press the button to change the character.
[UP], [DN]
buttons
• Select the Folder.
(
MP3/WMA disc only
)
[
RDM] button
• Perform random play while in the CD/MP3/WMA
mode.
• Press and hold the button for 1 second or longer
to perform folder random play while in the MP3/
WMA mode.
[
RPT] button
• Repeat play while in the CD/MP3/WMA mode.
• Press and hold the button for 1 second or longer
to perform folder repeat play while in the MP3/
WMA mode.
[
SCN] button
• Perform scan play for 10 seconds of each track
while in the CD/MP3/WMA mode.
• Press and hold the button for 1 second or longer
to perform folder scan play while in the MP3/
WMA mode.
[
DIRECT] buttons
• Store a station into memory or recall it directly
while in the radio mode.
[
SRC] button
• Press the button to turn on the power.
• Press and hold the button for 1 second or longer
to turn off the power.
• Switch the operation mode among the radio
mode, etc.
[
ROTARY
]
knob
• Adjust the volume by turning the knob clockwise
or counterclockwise.
• Use the knob to perform various settings.
Names of the Buttons and their Functions
[
A-M] button
• Press the button to switch to the audio mode.
(
bass/treble, balance/fader
• Press and hold for 1 second or longer to turn on
or off the M-B EX mode.
[
]
button
• Eject a CD when it is loaded into the unit.
)
[
, ] lever
• Select a station while in the radio mode or select
a track when listening to a CD. This lever is used
to make various settings.
• Press the lever upward or downward and hold
in position for 1 second or longer to enter the
fast-forward or fast-backward mode.
English
[
CD SLOT
• CD insertion slot.
]
Major Button Operations when external equipment is
connected to this unit
[
When the CD/DVD changer is
connected
∗ For details, see the section “CD changer opera-
tions”. For the DVD changer, refer to the Ownerʼs
Manual provided with the DVD changer.
[
]
button
• Play or pause a CD, DVD.
[D]
button
• Press the button to display the title
Title display, Clock display
• Press and hold the button for 1 second or longer
to enter the display adjust mode.
[T]
button
• Press the button switches the user titles or track
titles, etc. while in the CD changer mode.
• Press and hold the button for 1 second or longer
to input a title in the CD changer mode.
• Press the button to scroll the title during CD-text
play.
[
BND] button
• Move the next disc in increasing order.
[UP], [DN]
• Select the disc.
[
RDM] button
• Perform random play. Press and hold the button
for 1 second or longer to perform disc random
play.
[
RPT] button
• Perform repeat play. Press and hold the button
for 1 second or longer to perform disc repeat
play.
buttons
).
(
Main display,
SCN] button
• Perform scan play for 10 seconds of each track.
Press and hold the button for 1 second or longer
to perform disc scan play.
[
, ] lever
• Select a track when listening to a disc.
• Press the lever upward or downward and hold
in position for 1 second or longer to enter the
fast-forward or fast-backward mode.
When the TV is connected
∗ For details, see the section “TV Operations”.
[
]
button
• Perform preset scan while in the TV mode.
Press and hold the button for 2 seconds or
longer to perform auto store.
[
BND] button
• Switch the band.
Press and hold the button for 1 second or longer
to switch to the seek tuning or manual mode.
[
DIRECT] buttons
• Store a station into memory or recall it directly.
[
ADJ] button
• Press the button to switch to the ADJ mode.
• Press and hold the button for 1 second or
longer to switch to the TV picture mode or VTR
(
external) picture mode.
[
, ] lever
• Select a station.
DXZ466MP
5
Display Items
English
LCD Screen
In extreme cold, the screen movement may slow down and the screen may darken, but this is normal.
The screen will recover when it returns to normal temperature.
DXZ466MP
6
4. PRECAUTIONS
English
1. When the inside of the car is very cold and
the player is used soon after switching on the
heater moisture may form on the disc or the
optical parts of the player and proper playback
may not be possible. If moisture forms on the
disc, wipe it off with a soft cloth. If moisture
forms on the optical parts of the player, do
not use the player for about one hour. The
condensation will disappear naturally allowing
normal operation.
CAUTION
!
USE OF CONTROLS, ADJUSTMENTS, OR PERFORMANCE OF PROCEDURES OTHER THAN
THOSE SPECIFIED HEREIN, MAY RESULT IN HAZARDOUS RADIATION EXPOSURE.
THE COMPACT DISC PLAYER SHOULD NOT BE ADJUSTED OR REPAIRED BY ANYONE
EXCEPT PROPERLY QUALIFIED SERVICE PERSONNEL.
2. Driving on extremely bumpy roads which
cause severe vibration may cause the sound
to skip.
3. Thi s unit us es a pre cisi on mec h anis m.
Even in the event that trouble arises, never
open the case, disassemb le the unit, or
lubricate the rotating parts.
INFORMATION FOR USERS:
CHANGES OR MODIFICATIONS TO THIS PRODUCT NOT APPROVED BY THE MANUFACTURER WILL VOID THE WARRANTY.
DXZ466MP
7
English
5. HANDLING COMPACT DISCS
This unit has been designed specifically for playback of compact discs bearing the or
mark. No other discs can be played.
To remove the compact disc from its storage case,
press down on the center of the case and lift the
disc out, holding it carefully by the edges.
Always handle the compact disc by the edges.
Never touch the surface.
To remove fingermarks and dust, use a soft cloth,
and wipe in a straight line from the center of the
compact disc to the circumference.
New discs may have some roughness around
the edges. The unit may not work or the sound
may skip if such discs are used. Use a ball-point
pen, etc. to remove roughness from the edge of
the disc.
Note on compact discs
Never stick labels on the surface of the compact
disc or mark the surface with a pencil or pen.
Do not use any solvents such as commercially
available cleaners, anti-static spray, or thinner to
clean compact discs.
Do not use compact discs that have large scratch
es, are misshapen, or cracked, etc. Use of such
discs will cause misoperation or damage.
-
Do not expose compact discs to direct sunlight or
any heat source.
Note:
• Do not use commercially available CD protection sheets or discs equipped with stabilizers, etc. These
may get caught in the internal mechanism and damage the disc.
DXZ466MP
8
6. DCP (Detachable Control Panel
)
English
The control panel can be detached to prevent
theft. When detaching the control panel, store it
in the DCP
prevent scratches.
We recommend taking the DCP with you when
leaving the car.
(
Detachable Control Panel) case to
Removing the DCP
[
1. Press the
to switch off the power.
2. Press in the
∗ If the flip down panel does not open fully, gently
open it with your hand.
3. Pull the DCP toward you and remove it.
SRC] button for 1 second or longer
[
OPEN] button.
CAUTION
!
Be sure to close the HOLD FLAP for safety
when removing the DCP.
Attaching the DCP
1. Insert the right side of the DCP into the main
unit.
2. Insert the left side of the DCP to attach into
the main unit.
CAUTION
!
• The DCP can easily be damaged by shocks.
After removing it, be careful not to drop it or
subject it to strong shocks.
• If the FLIP DOWN PANEL is kept open, the
DCP may drop due to vibration of the car.
This result in damage to the DCP. So close
the FLIP DOWN PANEL or remove the DCP
to store into the case.
• The connector connecting the main unit and
the DCP is an extremely important part. Be
careful not to damage it by pressing on it
with fingernails, pens, screwdrivers, etc.
4. Close the HOLD FLAP.
Note:
• If the DCP is dirty, wipe off the dirt with a soft, dry
cloth only.
DXZ466MP
9
English
7. REMOTE CONTROL
Inserting the Battery
1. Turn over the remote control unit and slide the
cover in the direction indicated by the arrow in
the illustration.
2. Insert the battery (CR2025) into the insertion
gu ides , with th e pri n ted si de
upwards.
3. Press the battery in the direction indicated by the
arrow so that it slides into the compartment.
4. Replace the cover and slide in until it clicks
into place.
DXZ466MP
10
(+ )
fac ing
Notes:
Misuse may result in rupture of the battery, producing
leakage of fluid and resulting in personal injury or
damage to surrounding materials. Always follow these
safety precautions:
• Use only the designated battery.
• When replacing the battery, insert properly, with
+
/- polarities oriented correctly.
• Do not subject battery to heat, or dispose of in fire or
water. Do not attempt to disassemble the battery.
• Dispose of used batteries properly.
Functions of Remote Control Unit Buttons
English
Button
[
SRC
[
BND
[ ]
[ ]
[
[
MUTE
[
[
DISP
[
SCN
[
RPT
[
RDM
Mode
,
,
ISR
Radio
]
Press the button to power on.
Press and hold the button for 1 second or longer: Power off.
Switch among radio, CD/MP3/WMA, AUX, CD changer, DVD changer and TV.
Switch reception
]
band.
[ ]
Increase and decrease volume (in all modes).
[ ]
Move preset
channels up and
down.
]
No function.Switch between playback and pause.No function.
]
Turn mute on and off.
]
Recall ISR radio station in memory.
Press and hold for 2 seconds or longer: Store current station into ISR memory (radio mode
only).
]
Switch among main display, title display.
]
Preset scan.
Press and hold the
button for 2 seconds
or longer: Auto store.
]
No function.Repeat play.
]
No function.Random play.
CD/MP3/WMA
Play the first track.
Top play.
Move tracks up and down.
Press and hold the button for 1 second or
longer: Fast-forward/fast-backward.
Scan play.
Press and hold the
button for 1 second
or longer to perform
folder scan play while
in the MP3/WMA
mode.
Press and hold the
button for 1 second
or longer to perform
folder repeat play
while in the MP3/
WMA mode.
Press and hold the
button for 1 second
or longer to perform
folder random play
while in the MP3/
WMA mode.
CD Changer
DVD Changer
Move the next disc in
increasing order.
Scan play.
Press and hold the
button for 1 second
or longer: Disc scan
play.
Repeat play.
Press and hold the
button for 1 second
or longer: Disc repeat
play.
Random play.
Press and hold the
button for 1 second or
longer: Disc random
play.
Switch reception
band.
Move preset
channels up and
down.
Preset scan.
Press and hold the
button for 2 seconds
or longer: Auto store.
No function.
Switch between TV
and VTR.
TV
∗ Some of the corresponding buttons on the main unit and remote control unit have different functions.
DXZ466MP
11
English
8. OPERATIONS
Basic Operations
Note: Be sure to read this chapter referring to the front diagrams of
chapter “2. CONTROLS” on page 3.
CAUTION
!
Be sure to lower the volume before switching
off the unit power or the ignition key. The
unit remembers its last volume setting. If you
switch the power off with the volume up, when
you switch the power back on, the sudden loud
volume may hurt your hearing and damage
the unit.
Turning on/off the power
Note:
• Be careful about using this unit for a long time
without running the engine. If you drain the carʼs
battery too far, you may not be able to start the
engine and this can reduce the service life of the
battery.
1. Press the [SRC] button.
2. The illum inati on and display on the unit
light up. The unit automatically remembers its last operation mode and will automa tical ly switch to dis play that mode.
[
]
button for 1 second
3. Press and hold the
or longer to turn off the power for the unit.
Note:
• System check
The first time this unit is turned on after the wire
connections are completed, it must be checked
what equipment is connected. When the power is
turned on, the “SYSTEM CHECK” appears in the
display, then the unit returns to the clock display
mode. The system check starts within the unit.
When the system check is complete, press the
[
SRC] button again.
SRC
Selecting a mode
[
1. Press the
mode.
2. Each time you press the
eration mode changes in the following order:
Radio mode CD/MP3/WMA mode CD
changer mode DVD changer mode TV
mode AUX mode Radio mode...
∗ External equipment not connected with CeNET
is not displayed.
DXZ466MP
12
SRC] button to change the operation
[
]
button, the op
SRC
Note:
• If the CD mode is selected when no disc is inserted,
the display shows “NO DISC”.
Switching the display
]
Press the [D
Each time you press the
switches in the following order:
• Main display
• Title display
∗ In the case of a user title, only the top level is
displayed.
∗ In the case of radio/TV/AUX/DVD changer, the
display cannot be switched to “Title Display”.
∗ Once selected, the preferred display becomes the
display default. When a function adjustment such
as volume is made, the screen will momentarily
switch to that functionʼs display, then revert back
to the preferred display several seconds after the
adjustment.
∗ If the button operation is performed with the screen
saver function on, the operation display corre
sponding to the button operation is shown for about
30 seconds and the display returns to the screen
saver display.
For details, refer to the subsection “Turning the
screen saver function on or off” in section “
tions Common to Each Mode”.
-
∗ When you have entered a title in a CD/MP3/WMA,
it appears in the title display. If you have not en
tered a title, “NO TITLE” appears in the title display
instead.
For information on how to enter a title, refer to the
subsection “Entering titles” in section “
Common to Each Mode”.
button to select the desired display.
[D]
button, the display
-
Opera-
-
Operations
Basic Operations
English
Adjusting the volume
[
1. Press the front part of the
knob will pop up.
[
2. Turn i n g the
increases the volume; turning it counterclockwise decreases the volume.
∗ The volume level is from 0
(
maximum).
RO TA RY] kno b cl o ckwis e
ROTARY] knob. The
(
minimum) to 33
Audio mode adjustments
[
1. Press the
mode. The mode switches as follows each time
the [A-M] button is pressed:
BASS TREBLE BALANCE FADER
Previous mode
2. Turning the
lected audio mode.
BASS
Adjustment range : -6 to +7
TREBLE
Adjustment range : -6 to +6
BALANCE
Adjustment range : L13 to R13
FADER
Adjustment range : F12 to R12
∗ The display returns to the previous mode 7
seconds after the adjustment.
A-M] button to select the adjustment
[
ROTARY] knob to adjust the se
(
)
:
Bass
(
Treble) :
(
Fader
(
)
Balance
:
)
:
Adjusting the bass
1. Press the [A-M] button and select “BASS 0”.
[
2. Turning the
phasizes the bass; turning it counterclockwise
attenuates the bass.
∗ The factory default setting is “0”.
(
Adjustment range: -6 to +7
ROTARY] knob clockwise em
)
Adjusting the treble
]
1. Press the [A-M
0”.
2. Turning the
sizes the treble; turning it counterclockwise
attenuates the treble.
∗ The factory default setting is “0”.
(
Adjustment range: -6 to +6
button and select “
[
ROTARY] knob clockwise empha
TREBLE
)
Adjusting the balance
]
1. Press the [A-M
0”.
2. Turning the
sizes the sound from the right speaker; turning
it counterclockwise emphasizes the sound from
the left speaker.
∗ The factory default setting is “0”.
(
Adjustment range: L13 to R13
3. When the adjustment is complete, press the
[
]
button several times until the function
A-M
mode is reached.
button and select “
[
ROTARY] knob clockwise empha
)
Adjusting the fader
[
1. Press the
-
2. Turning the [ROTARY] knob clockwise em
phasizes the sound from the front speakers;
turning it counterclockwise emphasizes the
sound from the rear speakers.
∗ The factory default setting is “0”.
(
3. When the adjustment is complete, press the
[
A-M
mode is reached.
A-M] button and select “FADER 0”.
Adjustment range: F12 to R12
]
button several times until the function
)
Setting the Z-Enhancer
This unit are provided with 3 types of sound tone
effects stored in memory. Select the one you
prefer.
∗ The factory defa ult setting is “Z-ENHANCER
OFF”.
Each time you press the [Z
changes in the following order:
“OFF” “BASS BOOST” “IMPACT”
“EXCITE” “OFF” ...
• BASS BOOST : bass emphasized
• IMPACT : bass and treble emphasized
• EXCITE : bass and treble emphasized
mid de-emphasized
• OFF : no sound effect
-
]
button, the tone effect
BALANCE
-
-
DXZ466MP
13
Basic Operations
English
Radio Mode Operations
Adjusting MAGNA BASS EX
The MAGNA BASS EX does not adjust the low
sound area like the normal sound adjustment
function, but emphasizes the deep bass sound
area to provide you with a dynamic sound.
∗ The factory default setting is off.
[
1. Press and hold the
longer to turn on the MAGNA BASS EX effect.
“M-BASS EX ON” lights in the display.
2. Press and hold the
longer to turn off the MAGNA BASS EX effect.
“M-BASS EX OFF” lights in the display.
A-M] button for 1 second or
[
A-M] button for 1 second or
Listening to the radio
]
1. Press the [SRC
mode, then the radio will be on.
2. To select a preset band, press the
button, then select one of the preset bands
such as FM1, FM2, FM3 or AM. Every time
the [BND
change as:
FM1 FM2 FM3 AM FM1...
3. Press the
to tune in the desired station.
button and select the radio
[
BND
]
button is pressed, the display will
[
, ] lever upward or downward
Seek tuning
]
1. Press the [BND
“MANU” in the display goes off and seek tuning
2. Press the
When the lever is pressed upward, search
(
FM or AM
band
∗ If “MANU” is lit in the display, press and hold
the [BND
is now available.
to start automatic station tuning.
will be performing in the direction of higher
freq uen cie s. When the lever is pres sed
downward, search will be performed in the
direction of lower frequencies.
button and select the desired
)
.
]
button for 1 second or longer.
[ , ]
lever upward or downward
]
14
DXZ466MP
Manual tuning
There are 2 ways available: Quick tuning and
step tuning.
When you are in the step tuning mode, the
frequency changes one step at a time. In the quick
tuning mode, you can quickly tune the desired
frequency.
[
]
button and select the desired
1. Press the
band
∗ If “MANU” is not lit in the display, press and hold
the
“MANU” is lit in the display and manual tuning
is now available.
2. Tune into a station.
BND
(
FM or AM
[
BND
)
.
]
button for 1 second or longer.
Radio Mode Operations
English
• Quick tuning:
[
Press the
and hold in position for 1 second or longer to begin
station tuning.
, ] lever upward or downward
• Step tuning:
[
Press the
to perform manual tuning.
, ] lever upward or downward
Preset memory function
Pre set memory function can store up to 24
stations:
six stations for each of FM1, FM2, FM3 and AM.
Manual memory function
]
1. Press the [BND
want to store in the memory.
2. Press the
station.
3. Press and hold one of the
2 seconds or longer to store the current station
into preset memory.
button, to select a band you
[
, ] lever to tune into a desired
[
DIRECT
]
button for
Auto store
Auto store is a function for storing up to 6 stations
that are automatically tuned in sequentially.
If 6 receivable stations cannot be received, a
previously stored station remains unoverwritten
at the memory position.
[
]
button and select the desired
1. Press the
band
2. Press and hold the
seconds or longer. The stations with good
reception are stored automatically to the preset
channels.
BND
(
FM or AM
)
.
[
PS/ AS] button for 2
Recalling a preset station
(
A total of 24 preset positions
6-FM3, 6-AM) exists to store individual radio
stations in memory. Pressing the corresponding
[
DIRECT] button recalls the stored radio frequency
automatically.
[
1. Press the
2. Press the corresponding [DIRECT
(
FM or AM
band
recall the stored station.
∗ Press and hold one of the [DIRECT
2 seconds or longer to store that station into
preset memory.
]
button and select the desired
BND
)
.
Instant station recall (ISR
Instant station recall is a special radio preset that
instantly accesses a favorite radio station at a
touch of a button. The ISR function even operates
with the unit in other modes.
• ISR memory
1. Select the station that you wish to store in ISR
memory.
2. Press and hold the
or longer.
• Recalling a station with ISR
In any mode, press the [ISR
the radio function and tune the selected radio
station. “ISR” and its frequency appear in the
display. Press the
the previous mode.
[
ISR
[
]
button again to return to
ISR
6-FM1, 6-FM2,
]
button to
]
buttons for
)
]
button for 2 seconds
]
button to turn on
Preset scan
Preset scan receives the stations stored in preset
memory in order. This function is useful when
searching for a desired station in memory.
1. Press the
2. When a desired station is tuned in, press the
[
PS/AS] button again to continue receiving that
station.
Note:
• Be careful not to press and hold the
for 2 seconds or longer, otherwise the auto store
function is engaged and the unit starts storing sta
tions.
[
PS/AS] button.
[
PS/AS] button
-
DXZ466MP
15
CD/MP3/WMA Mode Operations
English
What is MP3?
MP3 is an audio compressio n meth od and
classified into audio layer 3 of MPEG standards.
This audio compression method has penetrated
into PC users and become a standard format. This
MP3 features the original audio data compression
to about 12 percent of its initial size with a high
quality sound. This means that about 10 music
CDs can be recorded on a CD-R disc or CD-RW
disc to allow a long listening time without having
to change CDs.
What is WMA?
WMA is the abbreviation of Windows Media
Audio, an audio file format developed by Microsoft
Corporation.
Notes:
• If you play a file with DRM
)
for WMA remaining ON, no audio is output.
ment
• Windows Media™, and the Windows
trademarks, or registered trademarks of Microsoft
Corporation in the United States and/or other
countries.
• To disable DRM
(
Digital Rights Management):
1. When using Windows Media Player 8, click on
TOOLS OPTIONS COPY MUSIC tab,
then under COPY SETTINGS unclick the
check box for PROTECT CONTENT. Then,
reconstruct files.
2. When using Windows Media Player 9, click on
TOOL OPTIONS MUSIC RECORD tab,
then under Recording settings, unclick the
Ch e c k bo x fo r RE C O R D PR O TECTED
MUSIC. Then, reconstruct files. Personally
constructed WMA files are used at your own
responsibility.
• Always add a file extension “.MP3” or “.WMA”
to MP3 or WMA file by using single byte letters.
If you add a file extension other than specified
or forget to add the file extension, the file
cannot be played
DXZ466MP
16
(
Digital Rights Manage
.
®
logo are
• Logical format (File system
1. When writing MP3/WMA file on a CD-R disc or
CD-RW disc, please select “ISO9660 level 1, 2 or JOLIET or Romeo” as the writing software
format. Normal play may not be possible if the
disc is recorded on another format.
2. The fol der name an d fil e name can be
displayed as the title during MP3/WMA play
but the title must be within 64 single byte
alphabetical letters and numerals
an extension).
3. Do not affix a name to a file inside a folder
having the same name.
)
• Folder structure
1. A d isc with a f older having more than 8
-
hierarchical levels will be impossible.
• Number of files or folders
1. Up to 255 files can be recognized per folder.
Up to 512 files can be played.
2. Tracks are played in the order that they were
recorded onto a disc.
be played in the order displayed on the PC.
3. Some noise may occur depending on the type
of encoder software used while recording.
(
Tracks might not always
CD-DA/MP3/WMA selection on
multi-session CD
When a disc contains both normal CD type tracks
and MP3/WMA tracks mixedly, you can select
which type of the recorded tracks to play.
• Default value is “CD”.
[
Each time you press and hold the
1 second or longer, the mixed mode is switched
between CD type or MP3/WMA type. The following
indication appears in the title display when
switching the track type to be played.
Display when
CD type track
is selected:
Display when
MP3/WMA
type track is
selected:
BND] button for
(
including
)
CD/MP3/WMA Mode Operations
English
1. Types of recording that can be played are as
follows.
Setting
Disc
Mixed with CD
and MP3/WMA
type tracks
CD type track only
MP3/WMA type
track only
Set to CD Set to MP3/WMA
Play CD
Play CD
Play MP3/
WMA
Play MP3/WMA
Play CD
Play MP3/WMA
2. After making these settings, remove the disc
and then reinsert it.
3. When a mixed mode CD is loaded and CD is
set, the track to be played first is MP3/WMA
file data and no sound is heard.
Note:
• When playing a CCCD (Copy Control CD), set the
setting to CD type. When this is set to MP3/WMA
type, the CD cannot be played normally in some
cases.
Disc-In-Play function
As long as the ignition key is turned to the ON
or ACC position, this function allows you to turn
the power to the unit and start playing the disc
automatically when the disc is inserted even if the
power is not turned on.
CAUTION
!
• Do not try to put your hand or fingers in the
disc insertion slot. Also never insert foreign
objects into the slot.
• Do not insert discs where adhesive comes
out from cellophane tape or a rental CD label,
or discs with marks where cellophane tape
or rental CD labels were removed. It may be
impossible to extract these discs from the
unit and they may cause the unit to break
down.
Backup eject function
Just pressing the
if the power to the unit was not turned on.
1. Press the
DOWN PANEL.
Note:
• If the FLIP DOWN PANEL will not open far enough,
open it gently with your hand.
[ ]
button ejects the disc even
[
OPEN] button to open the FLIP
2. Press the
[ ]
button. Remove the disc after it
is ejected.
3. Close the FLIP DOWN PANEL.
Notes:
• Always close the FLIP DOWN PANEL once you
take out the disc.
• If you force a CD into before auto reloading, this
can damage the CD.
(
• If a CD
• 8 cm CDs are not auto reloaded. Be sure to remove
12 cm) is left in the ejected position for 15
seconds, the CD is automatically reloaded.
reload).
it when ejected.
(
Auto
Listening to a disc already loaded
in the unit
[
Press the
SRC] button to select the CD/MP3/
WMA mode.
When the unit enters the CD/MP3/WMA mode,
play starts automatically.
If there is no disc loaded, the indication “NO DISC
appears in the title display.
∗ The mode changes each time the [SRC] button is
pressed. (Modes are not displayed for equipment
that is not connected.
)
Radio CD/MP3/WMA (CD changer)
(
DVD changer) (TV
)
AUX Radio...
Loading a CD
[
1. Press the
SLOT behind the FLIP DOWN PANEL.
2. Insert a CD into the center of the CD SLOT
with the labeled side facing up. The CD plays
automatically after loading.
Notes:
• Never insert foreign objects into the CD SLOT.
• If the CD is not inserted easily, there may be an
other CD in the mechanism or the unit may require
service.
• Discs not bearing the or mark and
CD-ROMs cannot be played by this unit.
• Some CDs recorded in CD-R/CD-RW mode may
not be usable.
OPEN] button to access the CD
”
-
DXZ466MP
17
CD/MP3/WMA Mode Operations
English
Loading 8 cm CD
∗ No adapter is required to play an 8 cm CD.
∗ Insert the 8 cm CD into the center of the insertion
slot.
3. Close the FLIP DOWN PANEL.
CAUTION
!
Be careful not to catch your hand or fingers
while closing the FLIP DOWN PANEL.
Notes:
• If the FLIP DOWN PANEL does not open fully,
gently open with your hand.
• After loading a CD, always close the FLIP DOWN
PANEL.
Pausing play
[
1. Press the
appears in the display.
2. To resume CD play, press the
again.
] button to pause play. “PAUSE
[
] button
Displaying CD titles
This unit can display title data for CD-text/MP3/
WMA disc and user titles input with this unit.
1. Press the
2. Each time you press the
display changes in the following order:
• CD-TEXT data
• MP3/WMA disc
[D]
button to display the title.
[T]
button, the title
Notes:
• If the CD playing is not a CD-text data or no user
title has been input, “
display.
• If MP3/WMA disc is not input TAG, “ NO TAG
appears in the display.
• For MP3, supports ID3 Tags V2.3/2.2/1.1/1.0.
• Tag displays give priority to V2.3/2.2
• In the case of album Tags for WMA, the information
written into the extension header is displayed.
• Only ASCII characters can be displayed in Tags.
U
NO TITLE” appears in the
Title display mode
1. There are 5 types of display for the Title Display
mode.
2. To select the next type, press the
”
less than 1 second.
The arrangement is shown below.
After 2 seconds
3. The displayed item can be scrolled by pressing
the [T] button for more than 1 second.
4. If a MP3/WMA file does not support for ID3
TAG, the display will show “NO TAG
5. If a MP3/WMA file encode with ID3 TAG header
but no consist of any TAG information, the
display will show nothing.
Notes:
• The folder name will be displayed as “ROOT” which
the file allocates in the root folder.
• The MP3 player decodes each file ID3 TAG ver 2
by default, if ID3 TAG ver 2 is unavailable, ID3 TAG
ver 1 will be decoded.
(
• UNICODE ID3
supported.
Chinese, Japanese and etc) is not
[T]
button for
”.
”
18
DXZ466MP
CD/MP3/WMA Mode Operations
English
Selecting a track
• Track-up
1. Press the
beginning of the next track.
2. Each time the
playback proceeds to another track in the
advancing direction.
[ ]
lever upward to move to the
[ ]
lever is pressed upward,
• Track-down
1. Press the
beginning of the current track.
2. Press the
to the beginning of the previous track.
[ ]
lever downward to move the
[ ]
lever downward twice to move
Fast-forward/fast-backward
• Fast-forward
Press the
1 second or longer.
• Fast-backward
Press the
tion for 1 second or longer.
∗ For MP3/WMA discs, it takes some time until the
[ ]
lever upward and hold in position for
[ ]
lever downward and hold in posi-
start of searching and between tracks. In addition,
the playing time may have a margin of error.
MP3/WMA playing order
When selected for play folder up down functions,
files and folders are accessed in the order in which
they were written by the CD-ROM writer. Because
of this, the order in which they are expected to
be played may not match the order in which they
are actually played. You may be able to set the
order in which MP3/WMA are to be played by
writing them onto a medium such as a CD-R with
their file names beginning with play sequence
numbers such as “01” to “99”, depending on your
CD writer.
For example, a medium with the following folder/
file hierarchy is shown below.
Example of a mediumʼs folder/file hierarchy
Folder select
This function allows you to selec t a fold er
containing MP3/WMA files and start playing from
the first track in the folder.
1. Press the [DN] or the [UP] button.
[DN]
Press the
folder. Press the
folder.
button to move the previous
[UP]
button to move the next
DXZ466MP
19
CD/MP3/WMA Mode Operations
English
]
∗ Press the [UP
to shift to the first folder.
∗ Fold er withou t an MP3/ WM A file i s not
selectable.
2. To select a track, press the
upward or downward.
button while in the final folder
[ , ]
lever
• Random play
This function allows you to play all tracks recorded
on a disc in a random order.
[
1. Press the
play.
“
RDM] button to perform random
RDM” appears in the display.
Top function
The top function resets the CD player to the first
track of the disc. Press the [BND
the first track (Track No. 1
∗ In case of MP3/WMA, the first track of a folder being
played will be returned.
]
button to play
)
on the disc.
Other various play functions
• Scan play
This function allows you to locate and play the first
10 seconds of all the tracks recorded on a disc.
[
]
1. Press the
“ SCN” appears in the display.
∗ Scan play starts from the next track after the
track currently being played.
• Folder scan play
This function allows you to locate and play the first
10 seconds of the first track of all the folders on
an MP3/WMA disc.
1. Press and hold the
or longer to perform folder scan play.
“
SCN” appears in the display.
∗ Folder scan pla y starts from the next trac k
after the track currently being played.
• Repeat play
This function allows you to play the current track
repeatedly.
1. Press the
“
RPT” appears in the display.
button to perform scan play.
SCN
[
]
button for 1 second
SCN
[
RPT] button to perform repeat play.
• Folder random play
This function allows you to play all the tracks of
all the folders recorded on an MP3/WMA disc in
a random order.
[
]
1. Press and hold the
or longer to perform folder random play.
“
RDM” appears in the display.
button for 1 second
RDM
• To cancel play
1. Pr e s s the o p erating bu t t on pr e v i o u s l y
selected.
• Folder repeat play
This function allows you to play a track currently
being played in the MP3/WMA folder repeatedly.
]
1. Press and hold the [RPT
or longer to perform folder repeat play.
“
RPT” appears in the display.
DXZ466MP
20
button for 1 second
Operations Common to Each Mode
To change display setting
]
1. Press and hold the [D
longer to switch to the adjustment selection
display.
2. Press the
[ , ]
to select the “item name”.
“CLOCK ”
Push ENT
“SCREEN SVR ”
“MSG INPUT ”
Push ENT
“AUTO SCROLL” “DIMMER”
“CONTRAST”
[
3. Turn the
ROTARY] knob to select the “desired
setting value”.
∗ After completing settings, press the [D
to return to the previous mode.
• Setting the clock
2-1. Select “ CLOCK ”.
3-1. Press the [ ] button.
3-2. Press the [ , ] lever upward or
downward to select the hour or the minute.
[
3-3. Turn the
ROTARY
time.
∗ The clock is displayed in 12-hour format.
[
3-4. Press the
] button to store the time into
memory.
Note:
• You cannot set the clock when it is displayed with
only the ignition on. If you drain or remove the carʼs
battery or take out this unit, the clock is reset. While
setting the clock, if another button or operation is
selected, the clock set mode is canceled.
• Turning the screen saver function on or
off
This unit is provided with the screen saver function
which allows you to show various kinds of patterns
and characters in the operation status indication
area of the display in a random order. You can turn
on and off this function.
If the button operation is performed with the
screen saver function on, the operation display
corresponding to the button operation is shown
for about 30 seconds and the display returns to
the screen saver display.
∗ The factory default setting is “Pattern SS”.
2-1. Select “ SCREEN SVR ”.
button for 1 second or
lever upward or downward
Push ENT
Push ENT
]
knob to set the correct
Push ENT
]
button
3-1. Turn the
Each time you turn the
the setting changes in the following order:
“
Pattern OFF” “Pattern SS” “Pattern
MESSAGE”
• Entering MESSAGE INFORMATION
Message up to 30 characters long can be stored
in memory and displayed as a type of screen
saver setting.
∗ The factory default setting is “WELCOME TO
CLARION
2-1. Select “ MSG INPUT ”.
3-1. Press the [ ] button.
3-2. Press and hold
longer to clear the old message.
3-3. Press the
ward to move the cursor.
3-4. Press the
Each time you press the [BND] button, the
character changes in the following orders:
Capital letters Small letters Numbers/
Symbols Umlaut Capital letters...
3-5. Turn the
character.
3-6. Repeat step 3-3 t o 3-5 to e nter up to 30
characters for message.
3-7. Press and hold the
or longer to store the message in memory
and cancel input message mode.
∗ Press and hold the
or longer to cancel the input message. Then
press and hold the
or longer to store the message and the mes
sage return to default setting.
• Setting the method for title scroll
Set how to scroll in CD-TEXT, MP3/WMA title.
∗ The factory default setting is “ON”.
2-1. Select “ AUTO SCROLL”.
3-1. Turn the
“OFF”.
• ON:
To scroll automatically.
• OFF:
To scroll just 1 time when the title was changed or the
[T]
button was pressed for 1 second or longer.
[
ROTARY] knob to select the setting.
[
ROTARY] kn ob,
”.
Push ENT
[
BND] button for 1 second or
[
, ] lever upward or down-
[
BND] button to select a character.
[
ROTARY] knob to select the desired
[ ]
button for 2 seconds
[
[
ROTARY
BND] button for
[
] button for 2 seconds
]
knob to select “ON” or
1 second
English
-
DXZ466MP
21
Operations Common to Each Mode
English
•
Adjusting the display scroll speed
This feature allows you to slow down the scroll
speed when the scroll speed is too fast, making it
difficult to view the screen.
∗ The factory default setting is “SPEED 3”
2-1. Select “ SCRL SPEED”.
[
3-1.Turn the
∗ This setting item can be adjusted within the
range SPEED 1 to SPEED 6.
Adjust this setting item while viewing how the
appearance of the display changes.
ROTARY] knob to select the setting.
• Dimmer control
You can setting the dimmer control “ON” or “OFF”.
∗ The factory default setting is “ON”.
2-1. Select “ DIMMER”.
[
3-1. Turn the
ROTARY] knob to select “ON” or
“OFF”.
• Adjusting the display contrast
You can adjust the display contrast to match the
angle of installation of the unit.
∗ The factory default setting is “08”.
(
Adjustment level: 01 to 16
)
2-1. Select “ CONTRAST”.
[
3-1. Turn the
ROTARY] knob to adjust the
contrast.
To change other settings
[
1. Press the
adjustment selection display.
2. Press the
ward to select the “item name”.
Eac h tim e the
up /down, the item display changes in the
following order:
BLINK LED” “AMP CANCEL”
“
“AUX SENS” “SYSTEM CHECK ”
3. Turn the
setting item”.
∗ After completing settings, press the [ADJ] but-
ton to return to the previous mode.
ADJ] bu tton to swit ch to th e
[ , ]
[
ROTARY] knob to select the “desired
lever upward or down
[ , ]
lever is pressed
Push ENT
• Anti-theft indicator
The red Anti-theft indicator is a function for preventing theft. When the DCP is removed from the
unit, this indicator blinks.
∗ The factory default setting is “OFF”.
2-1. Select “ BLINK LED”.
3-1. Turn the
[
ROTARY
]
knob to select “ON” or
“OFF”.
• Setting the external amplifier
∗ The factory default setting is “OFF”.
2-1. Select “ AMP CANCEL”.
3-1. Turn the
[
ROTARY
]
knob to select “ON” or
“OFF”.
• ON:
Use with connected AMP.
• OFF:
Use with inside AMP.
• Selecting AUX IN sensitivity
Make the following settings to select the sensitivity when sounds from external devices connected to this unit are difficult to hear even after
adjusting the volume.
∗ The factory default setting is “MID”.
2-1. Select “ AUX SENS”.
3-1. Turn the
[
ROTARY
]
knob to select “LOW”,
“MID” or “HIGH”.
• Trigger e d audio mute fo r cel l u l a r
telephones
This unit requires special wiring to mute the audio
signal automatically when a cellular telephone
rings in the car.
-
∗ This function is not compatible with all cellular
telephones. Contact your local authorized Clarion
dealer for information on proper installation and
compatibility.
• Performing a system check
This function allows you to perform a system check
from the adjust mode when required.
2-1. Select “
SYSTEM CHECK ”.
3-1. Press and hold the
[
] button for 1 second
Push ENT
or longer.
“SYSTEM CHECK” appears in the display,
then the unit re t u r n s to th e pr e v i o u s
operation mode.
22
DXZ466MP
Operations Common to Each Mode
English
Entering titles
Titles up to 10 characters long can be stored in
memory and displayed for CD, CD changer and TV
stations. The number of titles that can be entered
for each mode are as follows.
Mode Number of titles
CD mode 50 titles
TV mode 20 titles
Tuner mode 30 titles
CD changer mode Number of titles
DCZ625 connected 100 titles
CDC655Tz connected 100 titles
[
]
button to select the mode you
1. Press the
want to enter a title (TUNER, CD, CD changer
or TV
2. Select and play a CD in the CD changer or tune
in to a TV station or TUNER for which you want
to enter the title.
3. Press the
display.
4. Press and hold the
longer.
The display switches to the title input display.
5. Press the
to move the cursor.
6. Press the
Each time you press the
character changes in the following order:
Capital letters Small letters Numbers/
Symbols Umlaut Capital letters...
7. Turn the
character.
8. Repeat steps 5 to 7 to enter up to 10 characters
for the title.
9. Press and hold the
or longer to store the title into memory and
cancel title input mode.
SRC
)
.
[D]
button and display the title
[T]
button for 1 second or
[
, ] lever upward or downward
[
]
button to select a character.
BND
[
BND] button, the
[
ROTARY] knob to select the desired
[
] button for 2 seconds
Clearing titles
1. Select and play a CD in the CD changer or tune
in to a TV station or TUNER for which you want
to clear the title.
]
2. Press the [D
display.
3. Press and hold the
longer.
The display switches to the title input display.
4. Press and hold the
or longer.
All characters in the title disappear.
5. Press and hold the
or longer to clear the title and cancel title input
mode.
button and display the title
[T]
button for 1 second or
[
]
button for 1 second
BND
[
] button for 2 seconds
AUX function
This system has an external input jack so you
can listen to sounds and music from external devices connected to this unit.
DXZ466MP
23
English
9. OPERATIONS OF ACCESSORIES
CD Changer Operations
Note:
• The following operations are the same as for CD
mode:
∗ Pause
∗ Track selection
∗ Fast-forward/fast-backward
∗ Scan play
∗ Repeat play
∗ Random play
(
page 16-
See “CD/MP3/WMA Mode Operations
20) for details.
”
CD changer functions
When an optional CD changer is connected
through the CeNET cable, this unit controls all CD
changer functions. This unit can control a total of
2 changers.
[
Press the
mode to start play. If 2 CD changers are con
nected, press the [SRC
changer for play.
∗ If “NO MAGAZINE” appears in the display, in-
∗ If “NO DISC” appears in the display, eject
Note:
• Some CDs recorded in CD-R/CD-RW mode may
CD-ROM discs cannot be played from every CD
changer, itʼs depended on the model.
SRC] button and select the CD changer
]
button to select the CD
sert the magazine into the CD changer. “DISC CHECK” appears in the display while the player
loads (checks) the magazine.
the magazine and insert discs into each slot.
Then, reinsert the magazine back into the CD
changer.
not be usable.
CAUTION
!
Displaying CD titles
This unit can display title data for CD-text CDs and
user titles input with this unit.
∗ Title data for CD-text CDs can be displayed with
this unit only when it is connected to CDC655Tz.
1. Press the [D] button to display the title.
[T]
2. Each time you press the
display changes in the following order:
Notes:
• If the CD playing is not a CD-text CD or no user
title has been input, “ NO TITLE” appears in the
-
display.
• If a CD-text CD is not input its disc title or a track
O
title, “ NO TITLE” or “ NO TITLE” appears in
the display.
U
button, the title
Procedure to scroll a title
Set “AUTO SCROLL” to “ON” or “OFF”.
(
The factory default setting is “
subsection “Turning the screen saver function
on or off” in section “Operation common to
each mode”.
• When set to “ON”
The title is automatically kept scrolling.
• When set to “OFF”
To scroll just 1 time when the title was changed or the
[T]
button was pressed for 1 second or longer.
)
ON”. Refer to the
24
DXZ466MP
Selecting a CD
[UP]
Press the
disc.
∗ If a CD is not loaded in a slot of magazine, press-
ing the [UP] or [DN] button can not work.
or [DN] button to select the desired
CD Changer Operations
TV Operations
English
Other various play functions
• Disc scan play
Disc scan play locates and plays the first 10
seconds of the first track on each disc in the
currently selected CD changer. This function
continues automatically until it is cancelled.
∗ Disc scan play is useful when you want to select a
desired CD.
]
1. Press and hold the [SCN
or longer. “
disc scan play starts.
D.SCN” appears in the display and
• Disc repeat play
After all the tracks on the current disc have been
played, disc repeat play automatically replays the
current disc over from the first track.
This function continues automatically until it is
cancelled.
1. Press and hold the
or longer. “
disc repeat play starts.
D.RPT” appears in the display and
• Disc random play
The disc random play selects and plays individual
tracks or discs automatically in no particular
order.
This function continues automatically until it is
cancelled.
1. Press and hold the [RDM
or longer. “
disc random play starts.
D.RDM” appears in the display and
• To cancel play
1. Press the op e rating button previousl y
selected.
button for 1 second
[
]
button for 1 second
RPT
]
button for 1 second
Note:
• The following operations are performed the same
as for radio mode:
∗ Channel selection
∗ Storing channels in memory
∗ Calling channels from memory
∗ Auto store
∗ Preset scan
(
See “Radio Mode Operations”
details.
page 14-15) for
TV tuner functions
When an optional TV tuner is connected through
the CeNET cable, this unit controls all TV tuner
functions. To watch TV requires a TV tuner and
monitor.
Watching a TV
[
1. Press the
mode.
2. Press the
TV band (TV1 or TV2). Each time the button is
pressed, the input selection toggles between
TV1 and TV2.
3. Press the
to tune in the desired TV station.
SRC] button and select the TV
[
]
button to select the desired
BND
[ , ]
lever upward or downward
Watching a video
The TV tuner has a VTR input terminal to which 1
external device can be connected. Connect a 12
V video cassette player (VCP
recorder (VCR
1. Press and hold the
or longer to select VTR.
2. To return to the TV broadcast, press and hold
the [ADJ
)
to the TV tuner input terminal.
]
button for 1 second or longer.
)
or videocassette
[
]
button for 1 second
ADJ
Setting the TV area
(
When you select the TV area
)
, the TV tuner area setting changes.
area
1. Press the [ADJ] bu tton to switch to the
adjustment selection display.
2. Press the [ , ] lever upward or downward
to select “ TV AREA ”.
3. Press the
[ ]
Push ENT
button.
TV reception
DXZ466MP
25
TV Operations
English
[
4. Turn the
area.
5. Press the
6. Press the
mode.
ROTARY] knob to select the reception
[ ]
button.
[
ADJ] button to return to the previous
Setting the TV diver
You can change the reception setting for the TV
antenna connected to the TV tuner.
[
1. Press the
adjustment selection display.
2. Press the
to select “ TV DIVER”.
3. Turn the
“ON” or counterclockwise to set to “OFF”.
• ON:
Sets the diver setting to ON.
• OFF:
Sets the diver setting to OFF.
4. Press the
mode.
ADJ] bu tton to switch to the
[ , ]
[
ROTARY] knob clockwise to set to
[
ADJ] button to return to the previous
lever upward or downward
26
DXZ466MP
10. TROUBLESHOOTING
ProblemCauseMeasure
Power does not turn on.
(
No sound is produced
No sound output when
operating the unit with
amplifiers or power
antenna attached.
Fuse is blown.
)
Incorrect wiring.
Power antenna lead is
shorted to ground or
excessive current is
required for remote-on
the amplifiers or power
antenna.
Replace with a fuse of the same amperage.
If the fuse blows again, consult your store of
purchase.
Consult your store of purchase.
1. Turn the unit off.
2. Remove all wires attached to the power
antenna lead. Check each wire for a possible
short to ground using an ohm meter.
3. Turn the unit back on.
4. Reconnect each amplifier remote wire to
the power antenna lead one by on e. If
the amplifiers turn off before all wires are
attached, use an external relay to provide
remo te- on volt age
required).
(
exce ssi ve curr ent
English
General
Nothing happens when
button are pressed.
Display is not accurate.
No sound heard.
The microprocessor has
malfunctioned due to
noise, etc.
DCP or main unit
connectors are dirty.
The speaker protection
circuit is operating.
Turn off the power, then press the
button and remove the DCP.
Press the reset button for about 2 seconds
with a thin rod.
Wipe the dirt off with a soft cloth moistened
with cleaning alcohol.
1. Turn down sound volume. Function can
also be restored by turning the power off
and on again. (Speaker volume is reduced
automatically when the speaker protection
circuit operates).
2. If the sound is muted again, consult our
service department.
[
OPEN]
DXZ466MP
27
Troubleshooting
English
No sound heard.
Sound skips or is noisy.
Sound is cut or skipped.
Noise is generated or
CD/MP3/WMA
noise is mixed with
sound.
Sound is bad directly
after power is turned on.
Wrong filename
ProblemCauseMeasure
MP3/WMA files are
absent in a disc.
Files are not recognized
as an MP3/WMA file.
File system is not
correct.
Disc is dirty.
Disc is heavily scratched
or warped.
MP3/WMA files are not
encoded properly.
Water droplets may
form on the internal lens
when the car is parked
in a humid place.
File system is not
correct.
Write MP3/WMA files onto the disc properly.
Use MP3/WMA files encoded properly.
Use ISO9660 level 1, 2 or JOLIET or Romeo
file system.
Clean the disc with a soft cloth.
Replace with a disc with no scratches.
Use MP3/WMA files encoded properly.
Let dry for about 1 hour with the power on.
Use ISO9660 level 1, 2 or JOLIET or Romeo
file system.
28
DXZ466MP
11. ERROR DISPLAYS
Error DisplayCauseMeasure
ERROR 2
ERROR 3
CD/MP3/WMA
ERROR 6
Error DisplayCauseMeasure
ERROR 2
ERROR 3
CD Changer
ERROR 6
Error DisplayCauseMeasure
ERROR 2
ERROR 3
ERROR 6
DVD Changer
ERROR P
A DISC is caught inside the CD
deck and is not ejected.
A DISC cannot be played due
to scratches,etc.
A DISC is loaded upside-down
inside the CD deck and does
not play.
A CD inside the CD changer is
not loaded.
A CD inside the CD changer
cannot be played due to
scratches, etc.
A CD inside the CD changer
cannot be played because it is
loaded upside-down.
A DISC inside the DVD
changer cannot be played.
A DISC cannot be played due
to scratches, etc.
A DISC inside the DVD chang
er cannot be played because it
is loaded upside-down.
Parental level error.
Region code error.
ERROR R
This is a failure of CD deckʼs mechanism and
consult your store of purchase.
Replace with a non-scratched, non-warpeddisc.
Eject the disc then reload it properly.
This is a failure of CD changerʼs mechanism
and consult your store of purchase.
Replace with a non-scratched, non-warped
disc.
Eject the disc then reload it properly.
This is a failure of DVD mechanism and
consult your store of purchase.
Retry or replace with a non-scratched, nonwarped-disc.
-
Eject the disc then reload it properly.
Set the correct Parental level.
Eject the disc and replace correct region code
disc.
English
DXZ466MP
29
English
12. SPECIFICATIONS
FM tuner
Frequency Range: 87.0 MHz to 108 MHz
Usable Sensitivity: 11 dBf
50 dB Quieting Sensitivity: 17 dBf
Alternate Channel Selectivity: 75 dB
Stereo Separation (1 kHz): 35 dB
±
Frequency Response
(
3 dB): 30 Hz to 15 kHz
AM tuner
Frequency Range:
AM 531 kHz to 1629 kHz
Usable Sensitivity: 25 μV
CD player
System: Compact disc audio system
Usable Discs: Compact disc
±
Frequency Response: 10 Hz to 20 kHz
Signal-to-Noise Ratio: 85 dB (1 kHz) IHF-A
Dynamic Range: 80 dB (1 kHz
Harmonic Distortion: 0.01%