∗ Please read this ownerʼs manual in its entirety before operating this equipment.
∗ After reading this manual, be sure to keep it in a handy place (e.g., glove compartment).
∗ Check the contents of the enclosed warranty card and keep it carefully with this manual.
2
DXZ368RMP
This appliance contains a laser system and is
classified as a “CLASS 1 LASER PRODUCT”.
To use this model properly, read this Owner’s
Manual carefully and keep this manual for
your future reference. In case of any trouble
with this player, please contact your nearest
“AUTHORIZED service station”. To prevent
direct exposure to the laser beam, do not try
to open the enclosure.
CAUTIONS:
Denne mærking er anbragt udvendigt på apparatet og indikerer, at apparatet arbejder med
laserstråler af klasse 1, hvilket betyder, at der
anvendes laserstråler af svageste klasse, og
at man ikke på apparatets yderside kan blive
udsat for utilladelig kraftig stråling.
APPARATET BØR KUN ÅBNES AF FAGFOLK
MED SÆRLIGT KENDSKAB TIL APPARATER
MED LASERSTRÅLER!
Indvendigt i apparatet er anbragt den her
gengivne advarselsmækning, som advarer
imod at foretage sådanne indgreb i apparatet, at man kan komme til at udsaætte sig for
laserstråling.
USE OF CONTROLS OR ADJUSTMENTS
OR
PERFORMANCE OF PROCEDURES OTHER
THAN THOSE SPECIFIED IN THE OWNER’S
MANUAL MAY RESULT IN HAZARDOUS RADIATION EXPOSURE.
!CAUTION
ADVARSEL.
OBS!
VAROITUS
Apparaten innehåller laserkomponenten som
avger laserstrålning överstigande gränsen
för laserklass 1.
Suojakoteloa si saa avata. Laite sisältää la
serdiodin, joka lähettää näkymätöntä silmille
vaarallista lasersäteilyä.
1. When the inside of the car is very cold and
the player is used soon after switching on the
heater moisture may form on the disc or the
optical parts of the player and proper playback
may not be possible. If moisture forms on the
disc, wipe it off with a soft cloth. If moisture
forms on the optical parts of the player, do
not use the player for about one hour. The
condensation will disappear naturally allowing
normal operation.
INFORMATION FOR USERS:
CHANGES OR MODIFICATIONS TO THIS PRODUCT NOT APPROVED BY THE MANUFACTURER WILL VOID THE WARRANTY.
2. Driving on extremely bumpy roads which
cause severe vibration may cause the sound
to skip.
3. This unit is applicable for on-road 4 wheel vehicle purpose only. Use for tractor, fork truck,
bulldozer, off road vehicle, 2 or 3 wheel motor
bicycle, marine boat or other special purpose
vehicle is not appropriate.
3
Handling Compact Discs
This unit has been designed specifically for playback of compact discs bearing the or
mark. No other discs can be played.
To remove the compact disc from its storage
case, press down on the center of the case
and lift the disc out, holding it carefully by the
edges.
Always handle the compact disc by the edges.
Never touch the surface.
To remove fingermarks and dust, use a soft
cloth, and wipe in a straight line from the center
of the compact disc to the circumference.
New discs may have some roughness around
the edges. The unit may not work or the sound
may skip if such discs are used. Use a ball-point
pen, etc. to remove roughness from the edge
of the disc.
Note on compact discs
Never stick labels on the surface of the compact
disc or mark the surface with a pencil or pen.
Do not use any solvents such as commercially
available cleaners, anti-static spray, or thinner
to clean compact discs.
Do not use compact discs that have large
scratches, are misshapen, or cracked, etc.
Use of such discs will cause misoperation or
damage.
Do not expose compact discs to direct sunlight
or any heat source.
Note:
• Do not use commercially available CD protection sheets or discs equipped with stabilizers, etc. These
may get caught in the internal mechanism and damage the disc.
Be sure to unfold and read the next page. / Veuillez déplier et vous référer à la page suivante.
Bitte ausbreiten und die nächste Seite lesen. / Assicurarsi di aprire e leggere la pagina successiva.
Volgende pagina uitvouwen en doorlezen a.u.b. / Cerciórese de desplegar y de leer la página siguiente.
Glöm inte att vika ut och läsa nästa sida. / Não deixe de abrir e ler a próxima página.
4
EnglishFrançaisDeutschItaliano
CONTROLS / LES COMMANDES / REGLER / CONTROLLI
2.
REGELAARS / CONTROLES / KONTROLLER / CONTROLOS
MAIN UNIT / APPAREIL PRINCIPAL / HAUPTGERÄT
/ APPARECCHIO PRINCIPALE / HOOFDTOESTEL
/ UNIDAD PRINCIPAL / HUVUDENHET / UNIDADE PRINCIPAL
Nederlands
With the FLIP DOWN PANEL opened / Ouvrez le PANNEAU RABATTABLE
ÖFFNUNG DER KLAPPSCHALTTAFEL / Apertura del PANNELLO APRIBILE
Met het NEERKLAPBARE PANEEL geopend / Apertura del PANEL ABATIBLE
EspañolSvenska
DEN NEDFÄLLBARA PANELEN öppen
/ Abrindo o PAINEL RECLINÁVEL
Português
Note: Be sure to unfold this page and refer to the front diagrams as you read each chapter.
Remarque: Veuillez déplier cette page et vous référer aux schémas quand vous lisez chaque chapitre.
Hinweis: Bitte diese Seite ausfalten und beim Lesen der einzelnen Kapital die Frontdiagramme beachten.
Nota: Assicurarsi di aprire questa pagina e fare riferimento a questi diagrammi quando si legge ciascun capitolo.
Opmerking: Vouw deze pagina uit en zie tevens de afbeeldingen van het voorpaneel tijdens het doorlezen van de volgende hoofdstukken.
Nota: Cuando lea los capítulos, despliegue esta página y consulte los diagramas.
Observera: Vik ut denna sida för att kunna se figurerna över bilstereons framsida medan du läser de olika kapitlen.
Nota: Certifique-se de abrir esta página e consulte os diagramas frontais conforme realiza a leitura de cada capítulo.
DXZ368RMP
5
3. NOMENCLATURE
Note:
• Be sure to read this chapter referring to the front diagrams of chapter “2. CONTROLS” on page 5 (unfold).
Names of the Buttons and their Functions
[
OPEN] button
• Deeply push in [OPEN
down panel.
[
ADJ] button
• Press the button to switch to the ADJ mode.
When the button press and hold for 1 second or
longer to enter RDS ADJ mode.
[
]
button
• Perform preset scan while in the radio mode.
Press and hold the button for 2 seconds or
longer to perform auto store.
• Play or pause a CD while in the CD/MP3/WMA
mode.
[
SENSOR
• Receiver for remote control unit.
• Operating range: 30° in all directions.
[TA]
• Press the button to set the TA
ment) standby mode.
[D]
• Switch the display indication
display, Clock display
• Press and hold the button for 1 second or longer
to enter the display adjustment mode.
[Z]
• Press the button to select one of the 3 types
of sound characteristics already stored in
memory.
]
button
button
button
]
button to unlock the flip
(
Traffic Announce
(
Main display, Title
)
.
[
BND] button
• Switch the band, or seek tuning or manual tuning
while in the radio mode.
• Play a first track while in the CD/MP3/WMA
mode.
Press and hold the button for 1 second or longer
to perform multi-session.
• Press the button to change the character.
[UP], [DN]
• Select the Folder.
[
RDM] button
• Perform random play while in the CD/MP3/WMA
mode.
• Press and hold the button for 1 second or longer to perform folder random play while in the
MP3/WMA mode.
[
RPT] button
• Repeat play while in the CD/MP3/WMA mode.
• Press and hold the button for 1 second or longer
to perform folder repeat play while in the MP3/
WMA mode.
[
SCN] button
• Perform scan play for 10 seconds of each track
while in the CD/MP3/WMA mode.
• Press and hold the button for 1 second or longer
to perform folder scan play while in the MP3/
WMA mode.
[
DIRECT] buttons
• Store a station into memory or recall it directly
while in the radio mode.
buttons
(
MP3/WMA disc only
)
[T]
button
• Press the button to input a title in the CD
mode.
• Press the button to switch the user titles or track
titles, while in the CD/MP3/WMA mode.
• Press the button to scroll the title during the CDtext play, while in the CD/MP3/WMA mode.
[
SRC] button
• Press the button to turn on the power.
• Press and hold the button for 1 second or longer
to turn off the power.
• Switch the operation mode among the radio
mode, etc.
[
ROTARY
• Adjust the volume by turning the knob clockwise
or counterclockwise.
• Use the knob to perform various settings.
]
knob
67
Names of the Buttons and their Functions
English
[
A-M] button
• Press the button to switch to the audio mode.
(
bass/treble, balance/fader
• Press and hold for 1 second or longer to turn
on or off the M-B EX mode.
[
]
button
• Eject a CD when it is loaded into the unit.
[
CD SLOT
• CD insertion slot.
]
)
[
, ] lever
• Select a station while in the radio mode or select
a track when listening to a CD. This lever is used
to make various settings.
• Press the lever upward or downward and hold
in position for 1 second or longer to enter the
fast-forward or fast-backward mode.
Major Button Operations when external equipment is
connected to this unit
[
When the CD/DVD changer is
connected
∗ For details, see the section “CD changer opera-
tions”. For the DVD changer, refer to the Ownerʼs
Manual provided with the DVD changer.
[
]
button
• Play or pause a CD or DVD.
[D]
button
• Press the button to display the title.
play, Title display, Clock display
• Press and hold the button for 1 second or longer
to enter the display adjust mode.
)
(
Main dis
RPT] button
• Perform repeat play. Press and hold the button
for 1 second or longer to perform disc repeat
play.
[
SCN] button
• Perform scan play for 10 seconds of each track.
Press and hold the button for 1 second or longer
to perform disc scan play.
[
, ] lever
-
• Select a track when listening to a disc.
• Press the lever upward or downward and hold
in position for 1 second or longer to enter the
fast-forward or fast-backward mode.
[T]
button
• Press the button switches the user titles or track
titles, etc. while in the CD changer mode.
• Press and hold the button for 1 second or longer
to input a title in the CD changer mode.
• Press the button to scroll the title during CD-text
play.
[
BND] button
• Move the next disc in increasing order.
[UP]
, [DN] buttons
• Select the disc.
[
RDM] button
• Perform random play. Press and hold the button
for 1 second or longer to perform disc random
play.
When the TV/DAB is connected
∗ For details, see the section “TV Operations” or
“Digital Radio/DAB Operations”.
[
]
button
• Perform preset scan while in the TV mode.
Press and hold the button for 2 seconds or
longer to perform auto store.
only TV tuner.
• Perform service scan while in the DAB mode.
[TA]
button
• Press the button to set the TA
)
ment
function is only DAB tuner.
[
BND] button
• Switch the band.
Press and hold the button for 1 second or longer
to switch to the seek tuning or manual mode.
)
standby mode in the DAB mode.
(
This function is
(
Traffic Announce
)
DXZ368RMP DXZ368RMP
(
This
-
Major button operations when
English
external equipment is connected to
this unit
[
DIRECT] button
• Store a station into memory or recall it directly.
[
ADJ] button
• Press the button to switch to the ADJ mode.
• Press and hold the button for 1 second or
longer to switch to the TV picture mode or VTR
(
external) picture mode.
[
, ] lever
• Select a station.
DXZ368RMP DXZ368RMPDXZ368RMP
8
9
English
DXZ368RMP
In extreme cold, the screen movement may slow down and the screen may darken, but this is normal.
The screen will recover when it returns to normal temperature.
Display Items
LCD Screen
10
English
DXZ368RMP
4. REMOTE CONTROL (Optional item
)
1. Turn over the remote control unit and slide the
cover in the direction indicated by the arrow in
the illustration.
2. Insert the battery (CR2025) into the insertion
gu ides , with the pri nted side
(+ )
fac ing
upwards.
3. Press the battery in the direction indicated by the
arrow so that it slides into the compartment.
4. Replace the cover and slide in until it clicks
into place.
Notes:
Misuse may result in rupture of the battery, producing
leakage of fluid and resulting in personal injury or
damage to surrounding materials. Always follow these
safety precautions:
• Use only the designated battery.
• When replacing the battery, insert properly, with
+
/- polarities oriented correctly.
• Do not subject battery to heat, or dispose of in fire or
water. Do not attempt to disassemble the battery.
• Dispose of used batteries properly.
If you buy the RCB-176-700 sold separately, you can enjoy the use of the Remote Control function.
Inserting the Battery
11
English
DXZ368RMP
Radio (RDS)/DAB
Mode
Button
CD/MP3/WMA
CD Changer
DVD Changer
TV
Switch among radio, DAB, CD/MP3/WMA, CD changer, DVD changer and TV.
[
SRC
]
Switch reception
band.
Play the first track.
Top play.
Move the next disc in
increasing order.
Switch reception
band.
[
BND
]
Increase and decrease volume (in all modes).
Move preset
channels up and
down.
Move tracks up and down.
Press and hold the button for 1 second or
longer: Fast-forward/fast-backward.
Move preset channels up and down.
No function.Switch between playback and pause.No function.
Turn mute on and off.
TA on and off.
Switch among main display, title display, clock (CT
)
display.
Preset scan.
Press and hold the
button for 2 seconds
or longer: Auto store.
Scan play.
Press and hold the
button for 1 second
or longer to perform
folder scan play while
in the MP3/WMA
mode.
Scan play.
Press and hold the
button for 1 second
or longer: Disc scan
play.
Preset scan.
Press and hold the
button for 2 seconds
or longer: Auto store.
AF function on and
off.
Press and hold the
button for 1 second
or longer: REG
function on and off
Repeat play.
Press and hold the
button for 1 second
or longer to perform
folder repeat play
while in the MP3/
WMA mode.
Repeat play.
Press and hold the
button for 1 second
or longer: Disc repeat
play.
No function.
PTY mode on and off. Random play.
Press and hold the
button for 1 second
or longer to perform
folder random play
while in the MP3/
WMA mode.
Random play.
Press and hold the
button for 1 second or
longer: Disc random
play.
Switch between TV
and VTR.
[ ]
,
[
]
[ ]
,
[ ]
[
]
[
MUTE
]
[TA]
[
DISP
]
[
PS/AS
]
[AF]
[
PTY
]
∗ Some of the corresponding buttons on the main unit and remote control unit have different functions.
Functions of Remote Control Unit Buttons
12
English
DXZ368RMP
The control panel can be detached to prevent
theft. When detaching the control panel, store it
in the DCP
(
Detachable Control Panel) case to
prevent scratches.
We recommend taking the DCP with you when
leaving the car.
2. Press in the
[
OPEN] button.
3. Pull the DCP toward you and remove it.
Attaching the DCP
1. Insert the right side of the DCP into the main
unit.
2. Insert the left side of the DCP to attach into
the main unit.
• The DCP can easily be damaged by shocks.
After removing it, be careful not to drop it or
subject it to strong shocks.
• If the FLIP DOWN PANEL is kept open, the
DCP may drop due to vibration of the car.
This result in damage to the DCP. So close
the FLIP DOWN PANEL or remove the DCP
to store into the case.
• The connector connecting the main unit and
the DCP is an extremely important part. Be
careful not to damage it by pressing on it
with fingernails, pens, screwdrivers, etc.
5. DCP
CAUTION
!
Removing the DCP
1. Press the
[
SRC] button for 1 second or longer
to switch off the power.
∗ If the flip down panel does not open fully, gently
open it with your hand.
Note:
• If the DCP is dirty, wipe off the dirt with a soft, dry
cloth only.
4. Close the HOLD FLAP.
CAUTION
!
Be sure to close the HOLD FLAP for safety
when removing the DCP.
13
English
DXZ368RMP
Note: Be sure to read this chapter referring to the front diagrams of
chapter “2. CONTROLS” on page 5 (unfold).
6. OPERATIONS
CAUTION
!
Basic Operations
Be sure to lower the volume before switching
off the unit power or the ignition key. The
unit remembers its last volume setting. If you
switch the power off with the volume up, when
you switch the power back on, the sudden loud
volume may hurt your hearing and damage
the unit.
Turning on/off the power
Note:
• Be careful about using this unit for a long time
without running the engine. If you drain the carʼs
battery too far, you may not be able to start the
engine and this can reduce the service life of the
battery.
1. Press the [SRC] button.
2. The illum ination and disp lay on the unit
ligh t up. The un it auto maticall y remem bers its last operation mode and will automa tical ly swi tch to displ ay tha t mode .
3. Press and hold the
[
SRC
]
button for 1 second
or longer to turn off the power for the unit.
Note:
• The first time this unit is turned on after the wire
connections are completed, it must be checked
what equipment is connected. When the power is
turned on, “SYSTEM CHK” appears in the display,
then “
TUNER” appears in the display and goes to
radio mode.
Selecting a mode
1. Press the
[
SRC] button to change the operation
mode.
2. Each time you press the
[
SRC
]
button, the op
-
eration mode changes in the following order:
Radio mode DAB mode CD/MP3/WMA
mode CD changer mode DVD changer mode TV mode Radio mode...
∗ External equipment not connected with CeNET
is not displayed.
Note:
• If the CD mode is selected when no disc is inserted,
the display shows “NO DISC”.
Switching the display
Press the [D
]
button to select the desired display.
Each time you press the
[D]
button, the display
switches in the following order:
Main display Title display Clock
(CT)
display Main display
∗ Once selected, the preferred display becomes the
display default. When a function adjustment such
as volume is made, the screen will momentarily
switch to that functionʼs display, then revert back
to the preferred display several seconds after the
adjustment.
∗ When you have entered a title in a CD/MP3/WMA,
it appears in the title display. If you have not en
-
tered a title, “NO TITLE” appears in the title display
instead.
For information on how to enter a title, refer to the
subsection “Entering titles” in section “Operations Common to Each Mode”.
∗ When CT data is not received, “CT--:--” appears in
the display.
Adjusting the volume
Turning the
[
ROTARY] knob clockwise increases
the volume; turning it counter-clockwise decreases
the volume.
∗ The volume level is from 0 (minimum
)
to 33
(
maxi-
mum).
Audio mode adjustments
1. Press the
[
A-M] button to select the adjustment
mode. The mode switches as follows each time
the [A-M] button is pressed:
BASS TREB BAL FAD Previous
mode
2. Turning the
[
ROTARY] knob to adjust the se
-
lected audio mode.
BASS
(
Bass) : Adjustment range : -6 to
+
7
TREB
(
Treble) : Adjustment range : -6 to
+
6
BAL
(
Balance) : Adjustment range : L13 to R13
FAD
(
Fader) : Adjustment range : F12 to R12
∗ The display returns to the previous mode 7
seconds after the adjustment.
14
English
DXZ368RMP
Basic Operations
Setting the Z-Enhancer
This unit are provided with 3 types of sound tone
effects stored in memory. Select the one you
prefer.
∗ The factory default setting is “Z-EHCR OFF”.
Each time you press the [Z
]
button, the tone effect
changes in the following order:
“Z-EHCR OFF” “BASS BOOST” “IMPACT”
“EXCITE” “Z-EHCR OFF” ...
• BASS BOOST : bass emphasized
• IMPACT : bass and treble emphasized
• EXCITE : bass and treble emphasized
mid de-emphasized
• Z-EHCR OFF : no sound effect
Adjusting the balance
1. Press the [A-M] button and select “BAL 0”.
2. Turning the
[
ROTARY] knob clockwise empha
sizes the sound from the right speaker; turning
it counterclockwise emphasizes the sound from
the left speaker.
∗ The factory default setting is “BAL 0”.
(
Adjustment range: L13 to R13
)
3. When the adjustment is complete, press the
[
A-M
]
button several times until the function
mode is reached.
Adjusting the fader
1. Press the [A-M] button and select “FAD 0”.
2. Turn i ng the
[
RO TA RY] kno b cl o ckwi s e
emphasizes the sound from the front speakers;
turning it counterclockwise emphasizes the
sound from the rear speakers.
∗ The factory default setting is “FAD 0”.
(
Adjustment range: F12 to R12
)
3. When the adjustment is complete, press the
[
A-M
]
button several times until the function
mode is reached.
Adjusting MAGNA BASS EX
The MAGNA BASS EX does not adjust the low
sound area like the normal sound adjustment
function, but emphasizes the deep bass sound
area to provide you with a dynamic sound.
∗ The factory default setting is off.
1. Press and hold the
[
A-M] button for 1 second or
longer to turn on the MAGNA BASS EX effect.
“M-B EX” lights in the display.
2. Press and hold the
[
A-M] button for 1 second or
longer to turn off the MAGNA BASS EX effect.
“M-B EX” goes off from the display.
CT
(
Clock Time
)
function
The CT function receives CT data sent from an
RDS station and displays the time. Press the [D
]
button to switch to the CT display.
∗ If a CT data is not being received, “CT--:--” appears
in the display.
Note:
• CT data is not transmitted in some countries and
by some broadcast stations. Also, in some areas,
the CT may not display accurately.
15
English
DXZ368RMP
Radio Mode Operations
Listening to the radio
1. Press the [SRC
]
button and select the radio
mode, then the radio will be on.
2. To select a preset band, press the
[
BND
]
button, then select one of the preset bands
such as FM1, FM2, FM3 or AM. Every time
the [BND
]
button is pressed, the display will
change as:
FM1 FM2 FM3 AM FM1...
3. Press the
[
, ] lever upward or downward
to tune in the desired station.
Seek tuning
There are 2 types of seek tuning: DX SEEK and
LOCAL SEEK.
DX SEEK can automatically tune in to receivable
broadcast stations; LOCAL SEEK can tune in to
only broadcast stations with a good reception
sensitivity.
1. Press the
[
BND
]
button and select the desired
band
(
FM or AM (MW, LW
))
.
2. Tune into a station.
∗ If “MANU” is lit in the display, press and hold
the [BND
]
button for 1 second or longer.
“MANU” in the display goes off and seek tuning
is now available.
∗ If “TA” is lit in the display, TP stations are auto
-
matically sought.
• DX SEEK
Press the
[
, ] lever upward or downward
to start automatic station tuning.
When the lever is pressed upward, search will be
performing in the direction of higher frequencies.
When the lever is pressed downward, search
will be perf ormed in the direct ion of lower
frequencies.
∗ When seek tuning starts, “DX” appears in the
display.
• LOCAL SEEK
If the lever is pressed upward or downward and
held in position for 1 second or longer, local seek
tuning will be enabled. Broadcast stations with
good reception sensitivity are selected.
∗ When local seeking starts, “LO” appears in the
display.
Manual tuning
There are 2 ways available: Quick tuning and
step tuning.
When you are in the step tuning mode, the
frequency changes one step at a time. In the quick
tuning mode, you can quickly tune the desired
frequency.
1. Press the
[
BND
]
button and select the desired
band
(
FM or AM (MW/LW
))
.
∗ If “MANU” is not lit in the display, press and hold
the
[
BND
]
button for 1 second or longer.
“
MANU” is lit in the display and manual tuning
is now available.
2. Tune into a station.
∗ If no operation is performed for more than 7
seconds, manual tuning is cancelled and the
display returns to the previous mode.
• Quick tuning:
Press the
[
, ] lever upward or downward
and hold in position for 1 second or longer to begin
station tuning.
• Step tuning:
Press the
[
, ] lever upward or downward
to perform manual tuning.
∗ If no operation is performed for more than 7 sec-
onds, manual tuning is cancelled and the display
returns to the previous mode.
Preset memory function
Pre set memory function can store up to 24
stations:
six stations for each of FM1, FM2, FM3 and AM.
Manual memory function
1. Press the [BND
]
button, to select a band you
want to store in the memory.
2. Press the
[
, ] lever to tune into a desired
station.
3. Press and hold one of the [DIRECT
]
button for
2 seconds or longer to store the current station
into preset memory.
16
English
DXZ368RMP
Auto store
Auto store is a function for storing up to 6 stations
that are automatically tuned in seq uentially.
If 6 receivable stations cannot be received, a
previously stored station remains unoverwritten
at the memory position.
1. Press the
[
BND
]
button and select the desired
band
(
FM or AM (MW/LW
))
.
2. Press and hold the
[
PS/ AS] butto n for 2
seconds or longer. The stations with good
reception are stored automatically to the preset
channels.
∗ If auto store is performed in the FM bands, the
stations are stored in FM3 even if FM1 or FM2
was chosen for storing stations.
Radio Mode Operations
Preset scan
Preset scan receives the stations stored in preset
memory in order. This function is useful when
searching for a desired station in memory.
1. Press the
[
PS/AS] button.
2. When a desired station is tuned in, press the
[
PS/AS] button again to continue receiving that
station.
Note:
• Be careful not to press and hold the
[
PS/AS] button
for 2 seconds or longer, otherwise the auto store
function is engaged and the unit starts storing sta
-
tions.
Recalling a preset station
A total of 24 preset positions
(
6-FM1, 6-FM2,
6-FM3, 6-AM) exists to store individual radio
stations in memory. Pressing the corresponding
[
DIRECT] button recalls the stored radio frequency
automatically.
1. Press the
[
BND
]
button and select the desired
band
(
FM or AM (MW/LW
))
.
2. Press the corresponding [DIRECT
]
button to
recall the stored station.
∗ Press and hold one of the [DIRECT
]
buttons for
2 seconds or longer to store that station into
preset memory.
RDS Operations
RDS (Radio Data System
)
This unit has a built-in RDS decoder system that
supports broadcast stations transmitting RDS
data.
Th i s syst e m can di s play th e name of the
broadcast station being received
(PS)
and can
automatically switch to the broadcast station with
the best reception as you move long distances
(
AF switching).
Also, if a traffic announcement or programme
type is broadcast from an RDS station, no matter
what mode you are in, this broadcast is received.
Additionally, if EON information is received,
this information enables automatic switching of
other preset stations on the same network and
interruption of the station being received with traffic
information from other stations
(TP)
. This function
is not available in some areas.
When using the RDS function, always set the
radio to FM mode.
• AF : Alternative Frequency
• PS : Programme Service Name
• PTY : Programme Type
• EON : Enhanced Other Network
• TP : Traffic Programme
∗ RDS interrupt does not function during AM radio
reception.
∗ When set receives RDS signal, and can read PS
data, PS appears in the display.
AF function
The AF function switches to a different frequency
on the same network in order to maintain optimum
reception.
∗ The factory default setting is “ON”.
1. Press and hold the [ADJ
]
button for 1 second
or longer to switch to the RDS adjustment
Mode.
2. Press the
[
, ] lever upward or downward
to select “AF”.
3. Turn the
[
ROTARY] knob clockwise to select
“ON” or counter-clockwise to select “OFF”.
• ON:
“AF” in the display lights and AF function turns on.
• OFF:
“AF” in the display goes off and AF function turns off.
17
English
DXZ368RMP
RDS Operations
4. Press the
[
ADJ] button to return to the previous
mode.
∗ If the reception of the current broadcast station
deteriorates, “SEARCHING” appears in the
display and the radio searches for the same
programme on another frequency.
• AF function between RDS and DAB
When the same programme is broadcasted by
both RDS and DAB, and this function is ON, the
unit switches to receive the broadcast with the
better reception automatically.
∗ This function only operates when the DAH923 or
DAH913 DAB unit, sold separately, is connected.
∗ This factory default setting is “ON”.
1. Press the
[
ADJ] bu tton to swit ch to the
adjustment selection display.
2. Press the [ , ] lever upward or downward
to select “LINK ACT”.
3. Turn the
[
ROTARY] knob to select “ON” or
“OFF”.
• ON:
AF switching between DAB and RDS enabled.
• OFF:
AF switching between DAB and RDS disabled.
4. Press the
[
ADJ] button to return to the previous
mode.
REG
(
Regional programme) function
When the REG function is ON, the optimum
regional station can be received. When this function is OFF, if the regional station area switches
as you drive, a regional station for that region is
received.
∗ The factory default setting is “OFF”.
Notes:
• This function is disabled when a national station
such as BBC R2 is being received.
• The REG function ON/OFF setting is valid when
the AF function is ON.
1. Press and hold the [ADJ
]
button for 1 second
or longer to switch to the RDS adjustment
selection display.
2. Press the [ , ] lever upward or downward
to select “REG”.
3. Turn the
[
ROTARY] knob to select “ON” or
“OFF”.
• ON:
“REG” in the display lights and REG function turns
on.
• OFF:
“REG” in the display goes off and REG function
turns off.
4. Press the
[
ADJ] button to return to the previous
mode.
Manually tuning a regional station in
the same network
1. This function is valid when the AF function is
ON and the REG function is OFF.
Note:
• This function can be used when a regional broad
-
cast of the same network is received.
2. Press any one of the [DIRECT
]
buttons to call
out the regional station.
3. If the reception condition of the called out sta
-
tion is bad, press the [DIRECT
]
button of the
same number. The unit receives a local station
on the same network.
TA
(
Traffic Announcement
)
In the TA standby mode, when a traffic announcement broadcast starts, the traffic announcement
broadcast is received as top priority regardless
of the function mode so you can listen to it.
Traffic programme (TP) automatic tuning is also
possible.
∗ This function can only be used when “TP” is lit in
the display. When “
TP” is lit, this means that the
RDS broadcast station being received has traffic
announcement programmes.
• Setting the TA standby mode
If you press the
[TA]
button when only “
TP” is lit
in the display, “TP” and “TA” light in the display
and the unit is set into the TA standby mode until a
traffic announcement is broadcast. When a traffic
announcement broadcast starts, “TRA INFO”
appears in the display. If you press the
[TA]
button
while a traffic announcement broadcast is being
received, the traffic announcement broadcast
reception is cancelled and the unit goes into the
TA standby mode.
18
English
DXZ368RMP
RDS Operations
• Cancelling the TA standby mode
As “TP” and “TA” lit in the display, press the
[TA]
button. The “TA” in the display goes off and the
TA standby mode is cancelled.
∗ If “TP” is not lit, pressing the
[TA]
button searches
for a TP station.
• Searching for a TP station
When “TP” is not lit, if you press the
[TA]
button,
“TA” in the display lights and the unit automatically
receives a TP station.
Note:
• If a TP station is not received, the unit continues
the search operation. Pressing
[TA]
button again
goes off “TA” in the display and stops TP station
searching.
Auto store function for TP stations
You can automatically store up to 6 TP stations
into preset memory. If the number of TP can be
received less than 6, broadcast stations already
stored in memory and left without being overwritten.
As “TA” lit in the display, press and hold the
[
]
button for 2 seconds or longer. The TP stations
with the good reception sensitivity are stored into
preset memory.
∗ Even if you select FM1 or FM2, a TP station is
stored into memory for FM3.
RDS MODE adjustment
Press and hold the [ADJ
]
button for 1 second or
longer to select the RDS MODE.
The mode switches as follows ea ch time the
[ , ]
lever are pressed upward or downward:
PTY ON PTY-S<E> AF ON REG
ON∗ INFO SEL (E) ....
Press [ADJ] button to exit RDS MODE.
∗ “REG ON” only available when “AF ON”.
PTY
This function enables you to listen to a broadcast
of the selected programme type even if the unit is
on a function mode other than radio.
∗ Some countries do not yet have PTY broadcast.
∗ In the TA standby mode, a TP station has priority
over a PTY broadcast station.
∗ The factory default setting is “OFF”.
1. Press and hold the [ADJ
]
button for 1 second
or longer to switch to the RDS adjustment
selection display.
2. Press the [ , ] lever upward or downward
to select “
PTY”.
3. Turn the
[
ROTARY] knob to select “ON” or
“OFF”.
• ON:
“PTY” in the display lights and PTY standby mode is
turned on. When the selected PTY broadcast starts,
the PTY item name appears in the display.
• OFF:
“PTY” in the display goes off and PTY standby mode
is cancelled.
4. Press the
[
ADJ] button to return to the previous
mode.
• Cancelling a PTY interrupt broadcast
Press the
[TA]
button during the PTY interrupt
broadcast, the PTY interrupt is cancelled and the
unit returns to PTY standby mode.
Selecting PTY
1. Press and hold the [ADJ
]
button for 1 second
or longer to switch to the RDS adjustment
mode.
2. Press the
[
, ] lever upward or downward
to select “PTY-SEL <E>”.
3. Press the
[
] button.
4. Press any one of the
[
DIRECT
]
buttons to call
the Preset Memory for PTY selection..
Alternatively, turn the
[
ROTARY] knob to select
the desired PTY.
5. Press the
[
ADJ] button to return to the previous
mode.
∗ Below are the factory default settings stored for
the [DIRECT] buttons.
19
English
DXZ368RMP
∗ The PTY select mode is cancelled automatically 7
seconds after a PTY is selected.
RDS Operations
Preset
number
News
Info
Pop M
Sport
Classics
Easy M
ENGLISH
PTY item
Contents
1
2
3
4
5
6
News
Information
Pop Music
Sport
Serious Classical Music
Easy Listening Music
PTY seek
1. Press and hold the [ADJ
]
button for 1 second
or longer to switch to the RDS adjustment
selection display.
2. Press the
[
, ] lever upward or downward
to select “PTY-SEL <E>”.
3. Press the
[ ]
button.
4. Press the
[
] lever upward to search for
a PTY broadcast in the direction of higher
frequencies; press the [ ] lever downward to
search in the direction of lower frequencies.
∗ If no station with the selected PTY broadcast
can be received, the unit returns to the PTY
select mode.
PTY preset memory
1. Press and hold the [ADJ
]
button for 1 second
or longer to switch to the RDS adjustment
selection display.
2. Press the [ , ] lever upward or downward
to select “PTY-SEL <E>”.
3. Press the [ ] button.
4. Turning the
[
ROTARY] knob to select the
desired PTY.
The 29 types of PTY below can be selected.
5. If you press and hold any one of the
[
DIRECT]
buttons for 2 seconds or longer, the selected
PT Y is st o red in t o tha t prese t chann el
memory.
Emergency broadcast
If an emergency broadcast is received, all the
function mode operations are stopped.
“ALARM” appears in the display and the emergency broadcast can be heard.
PTY item
ENGLISH
News
Affairs
Info
Sport
Educate
Drama
Culture
Science
Varied
Pop M
Rock M
Easy M
Light M
Classics
Other M
Weather
Finance
Children
Social
Religion
Phone In
Travel
Leisure
Jazz
Country
Nation M
Oldies
Folk M
Document
Contents
News
Todayʼs events
Information
Sports
Education
Drama
Culture
Science
Variety
Pop music
Rock music
Easy music
Light music
Classics
Other music
Weather
Finance
For children
Social
Religion
Phone in
Travel
Leisure
Jazz
Country
Nation music
Oldies
Folk music
Documentaries
• Cancelling an emergency broadcast
If you press the
[TA]
button, emergency broadcast
reception is cancelled.
20
English
DXZ368RMP
Switching the PTY display language
You can select one of 4 languages
(
English,
Ge rman , Swed ish or Frenc h) for the PT Y
displayed in the display.
∗ The factory default setting is “ENGLISH”.
1. Press the
[
ADJ] bu tton to swit ch to the
adjustment selection display.
2. Press the
[
, ] lever upward or downward
to select “LANGUAGE”.
3. Turn the
[
ROTARY] knob to select the desired
language.
4. Press the
[
ADJ] button to return to the previous
mode.
RDS Operations
Volume setting of TA, emergency
broadcast (ALARM) and PTY
The volume for TA, ALARM and PTY interrupts can
be set during TA, ALARM or PTY interrupt.
∗ The factory default setting is “15”.
During a TA, ALARM or PTY interrupt, turn the
[
ROTARY] knob to set the volume to the desired
level (0 to 33).
∗ When the TA, ALARM or PTY interrupt ends, the
volume returns to the level it had before the inter
-
rupt.
CD/MP3/WMA
Mode Operations
What is MP3?
MP3 is an audio compr essio n meth od and
classified into audio layer 3 of MPEG standards.
This audio compression method has penetrated
into PC users and become a standard format. This
MP3 features the original audio data compression
to about 12 percent of its initial size with a high
quality sound. This means that about 10 music
CDs can be recorded on a CD-R disc or CD-RW
disc to allow a long listening time without having
to change CDs.
What is WMA?
WMA is the abbreviation of Windows Media
Audio, an audio file format developed by Microsoft
Corporation.
Notes:
• If you play a file with DRM
(
Digital Rights Manage
-
ment
)
for WMA remaining ON, no audio is output.
• Windows Media™, and the Windows
®
logo are
trademarks, or registered trademarks of Microsoft
Corporation in the United States and/or other
countries.
• To disable DRM
(
Digital Rights Management):
1. When using Windows Media Player 8, click on
TOOLS OPTIONS COPY MUSIC tab,
then under COPY SETTINGS unclick the
check box for PROTECT CONTENT. Then,
reconstruct files.
2. When using Windows Media Player 9, click on
TOOL OPTIONS MUSIC RECORD tab,
then under Recording settings, unclick the
Ch e c k bo x fo r RE C ORD PROTEC T E D
MUSIC. Then, reconstruct files. Personally
constructed WMA files are used at your own
responsibility.
to MP3 or WMA file by using single byte letters.
If you add a file extension other than specified
or forget to add the file extension, the file
cannot be played
.
CD/MP3/WMA Mode Operations
• Logical format (File system
)
1. When writing MP3/WMA file on a CD-R disc or
CD-RW disc, please select “ISO9660 level 1, 2 or JOLIET or Romeo” as the writing software
format. Normal play may not be possible if the
disc is recorded on another format.
2. The fol der name and fil e nam e can be
displayed as the title during MP3/WMA play
but the title must be within 64 single byte
alphabetical letters and numerals
(
including
an extension).
3. Do not affix a name to a file inside a folder
having the same name.
• Folder structure
1. A disc with a fold er having mor e than 8
hierarchical levels will be impossible.
• Number of files or folders
1. Up to 255 files can be recognized per folder.
Up to 512 files can be played.
2. Tracks are played in the order that they were
recorded onto a disc.
(
Tracks might not always
be played in the order displayed on the PC.
)
3. Some noise may occur depending on the type
of encoder software used while recording.
CD-DA/MP3/WMA selection on
multi-session CD
1. If a multi-session CD which contains CD-DA
and MP3/WMA files is being inserted, user can
select either CD-DA or MP3/WMA files to be
played.
2. Defa ult setting for file s to be playe d on
multisession CD is CD-DA files.
3. Press the
[
BND] button for more than 1 second
will toggle between selection of CD-DA and
[
MP3/WMA
]
files to be played.
4. When CD-DA type is selected, display will
show “M-SESS CD”. When MP3/WMA type is
selected, display will show “M-SESS MP3”.
7. When a mixed mode CD is loaded and CD is
set, the track to be played first is MP3/WMA
file data and no sound is heard.
Note:
• When playing a CCCD (Copy Control CD), set the
setting to CD type. When this is set to MP3/WMA
type, the CD cannot be played normally in some
cases.
Play MP3/WMA
Play CD
Play MP3/WMA
Setting
Disc
Mixed with CD
and MP3/WMA
type tracks
CD type track only
MP3/WMA type
track only
Play CD
Play CD
Play MP3/
WMA
Set to CD Set to MP3/WMA
• Do not try to put your hand or fingers in the
disc insertion slot. Also never insert foreign
objects into the slot.
• Do not insert discs where adhesive comes
out from cellophane tape or a rental CD label,
or discs with marks where cellophane tape
or rental CD labels were removed. It may be
impossible to extract these discs from the
unit and they may cause the unit to break
down.
CAUTION
!
Backup eject function
Just pressing the
[ ]
button ejects the disc even
if the power to the unit was not turned on.
1. Press the
[
OPEN] button to open the FLIP
DOWN PANEL.
5. CD-DA/MP3/WMA Selection function can only
be performed in CD/MP3/WMA mode. It will
only activate after re-insert CD. For example,
current setting is CD-DA type. Press
[
BND
]
button for more than 1 second to set MP3/WMA
type. User has to eject CD and re-insert again
as to play MP3/WMA files.
6. Types of recording that can be played are as
follows.
22
English
DXZ368RMP
Note:
• If the FLIP DOWN PANEL will not open far enough,
open it gently with your hand.
2. Press the
[ ]
button. Remove the disc after it
is ejected.
3. Close the FLIP DOWN PANEL.
Notes:
• Always close the FLIP DOWN PANEL once you
take out the disc.
• If you force a CD into before auto reloading, this
can damage the CD.
• If a CD
(
12 cm) is left in the ejected position for 15
seconds, the CD is automatically reloaded.
(
Auto
reload).
• 8 cm CDs are not auto reloaded. Be sure to remove
it when ejected.
CD/MP3/WMA Mode Operations
Listening to a disc already loaded
in the unit
Press the
[
SRC] button to select the CD/MP3/
WMA mode.
When the unit enters the CD/MP3/WMA mode,
play starts automatically.
If there is no disc loaded, the indication “NO DISC
”
appears in the title display.
∗ The mode changes each time the [SRC] button is
pressed. (Modes are not displayed for equipment
that is not connected.
)
Radio (DAB
)
CD/MP3/WMA
(
CD changer) (DVD changer) (TV)
Radio...
Loading a CD
1. Press the
[
OPEN] button to access the CD
SLOT behind the FLIP DOWN PANEL.
2. Insert a CD into the center of the CD SLOT
with the labeled side facing up. The CD plays
automatically after loading.
Notes:
• Never insert foreign objects into the CD SLOT.
• If the CD is not inserted easily, there may be an
other CD in the mechanism or the unit may require
service.
• Discs not bearing the or mark and
CD-ROMs cannot be played by this unit.
• Some CDs recorded in CD-R/CD-RW mode may
not be usable.
Be careful not to catch your hand or fingers
while closing the FLIP DOWN PANEL.
Notes:
• If the FLIP DOWN PANEL does not open fully,
gently open with your hand.
• After loading a CD, always close the FLIP DOWN
PANEL.
CAUTION
!
Pausing play
1. Press the
[
] button to pause play. “PAUSE
”
appears in the display.
2. To resume CD play, press the
[
] button again.
Displaying CD titles
This unit can display title data for CD-text/MP3/
WMA disc and user titles input with this unit.
1. Press the [D] button to display the title.
2. Each time you press the [T
]
button, the title
display changes in the following order:
• CD-TEXT data
User title
(
disc) CD-text title (disc) Artist name
CD-text title (track) User title (disc)...
• MP3/WMA disc
Folder Track Album TAG Artist TAG
Title TAG Folder...
Notes:
• If the CD playing is not a CD-text data or no user
title has been input, “NO TITLE” appears in the
display.
• If MP3/WMA disc is not input TAG, “NO TAG” ap
-
pears in the display.
• For MP3, supports ID3 Tags V2.3/2.2/1.1/1.0.
• Tag displays give priority to V2.3/2.2
• In the case of album Tags for WMA, the information
written into the extension header is displayed.
• Only ASCII characters can be displayed in Tags.
Display selection
1. You can choose the display type for MP3/WMA
CD by pressing the [D] button.
To select the next type, press the
[D]
button
again.
23
English
DXZ368RMP
The arrangement is shown below.
CD/MP3/WMA Mode Operations
Title display mode
1. There are 5 types of display for the Title Display
mode.
2. To select the next type, press the
[T]
button for
less than 1 second.
The arrangement is shown below.
3. The displayed item can be scrolled by pressing
the [T] button for more than 1 second.
4. If a MP3/WMA file does not support for ID3
TAG, the display will show “NO TAG
”
5. If a MP3/WMA file encode with ID3 TAG header
but no consist of any TAG information, the
display will show nothing.
Notes:
• The folder name will be displayed as “ROOT” which
the file allocates in the root folder.
• The MP3 player decodes each file ID3 TAG ver 2
by default, if ID3 TAG ver 2 is unavailable, ID3 TAG
ver 1 will be decoded.
• UNICODE ID3
(
Chinese, Japanese and etc) is not
supported.
Selecting a track
• Track-up
1. Press the
[ ]
lever upward to move to the
beginning of the next track.
2. Each time the
[ ]
lever is pressed upward,
playback proceeds to another track in the
advancing direction.
• Track-down
1. Press the
[ ]
lever downward to move the
beginning of the current track.
2. Press the
[ ]
lever downward twice to move
to the beginning of the previous track.
Fast-forward/fast-backward
• Fast-forward
Press the
[ ]
lever upward and hold in position for
1 second or longer.
• Fast-backward
Press the
[ ]
lever downward and hold in position
for 1 second or longer.
∗ For MP3/WMA discs, it takes some time until the
start of searching and between tracks. In addition,
the playing time may have a margin of error.
MP3/WMA playing order
When selected for play folder up down functions,
files and folders are accessed in the order in which
they were written by the CD-ROM writer. Because
of this, the order in which they are expected to
be played may not match the order in which they
are actually played. You may be able to set the
order in which MP3/WMA are to be played by
writing them onto a medium such as a CD-R with
their file names beginning with play sequence
numbers such as “01” to “99”, depending on your
CD writer.
For example, a medium with the following folder/
file hierarchy is shown below.
After 2 seconds
24
English
DXZ368RMP
Example of a mediumʼs folder/file hierarchy
CD/MP3/WMA Mode Operations
Folder select
This funct ion allow s you to select a folde r
containing MP3/WMA files and start playing from
the first track in the folder.
1. Press the [DN] or the [UP] button.
Press the
[DN]
button to move the previous
folder. Press the
[UP]
button to move the next
folder.
∗ Press the [UP
]
button while in the final folder
to shift to the first folder.
∗ Folder without an MP3/WMA file is not selectable.
2. To select a track, press the
[ , ]
lever
upward or downward.
Top function
The top function resets the CD player to the first
track of the disc. Press the [BND
]
button to play
the first track
(
track No. 1) on the disc.
∗ In case of MP3/WMA, the first track of a folder being
played will be returned.
Other various play functions
• Scan play
This function allows you to locate and play the first
10 seconds of all the tracks recorded on a disc.
1. Press the
[
SCN
]
button to perform scan play.
The indication “SCN” lights in the display.
∗ Scan play starts from the next track after the
track currently being played.
• Folder scan play
This function allows you to locate and play the first
10 seconds of the first track of all the folders on
an MP3/WMA disc.
1. Press and hold the
[
SCN
]
button for 1 second
or longer to perform folder scan play.
The indications “
ALL...” and “SCN” light in the
display.
∗ Folder s can play starts from th e next tr ack
after the track currently being played.
• Repeat play
This function allows you to play the current track
repeatedly.
1. Press the
[
RPT] button to perform repeat play.
The indication “
RPT” lights in the display.
• Folder repeat play
This function allows you to play a track currently
being played in the MP3/WMA folder repeatedly.
1. Press and hold the [RPT
]
button for 1 second
or longer to perform folder repeat play.
The indications “
ALL...” and “RPT” light in the
display.
25
English
DXZ368RMP
• Random play
This function allows you to play all tracks recorded
on a disc in a random order.
1. Press the
[
RDM] button to perform random
play.
The indication “
RDM” lights in the display.
CD/MP3/WMA Mode Operations
• Folder random play
This function allows you to play all the tracks of
all the folders recorded on an MP3/WMA disc in
a random order.
1. Press and hold the
[
RDM
]
button for 1 second
or longer to perform folder random play.
The indications “
ALL...” and “RDM” light in the
display.
• To cancel play
1. Pr e s s the o p erating bu tton pr e v i o usly
selected.
Operations Common to
Each Mode
To change display setting
1. Press and hold the [D
]
button for 1 second or
longer to switch to the adjustment selection
display.
2. Press the
[ , ]
lever upward or downward
to select the “item name”.
“
SCREEN SVR” “MSG INP(E)”
“AUTO SCROL” “DIMMER”
3. Turn the
[
ROTARY] knob to select the “desired
setting value”.
∗ In the case of item names appearing with the
“E” suffix, after the item name, the
[
] button
must be pressed to display the setting value.
∗ After completing settings, press the [D
]
button
to return to the previous mode.
• Turning the screen saver function on
or off
This unit is provided with the screen saver function
which allows you to show various kinds of patterns
and characters in the operation status indication
area of the display in a random order. You can turn
on and off this function.
If the button operation is performed with the
screen saver function on, the operation display
corresponding to the button operation is shown
for about 30 seconds and the display returns to
the screen saver display.
∗ The factory default setting is “ON”.
2-1. Select “SCREEN SVR”.
3-1. Turn the
[
ROTARY] knob to select the setting.
Each time you turn the [ROTARY] kn ob,
the setting changes in the following order:
SS OFF SS ON SS MESSAGE.
• Entering MESSAGE INFORMATION
Message up to 30 characters long can be stored
in memory and displayed as a type of screen
saver setting.
∗ The factory default setting is “WELCO ME TO
CLARION
”.
26
English
DXZ368RMP
Operations Common to Each Mode
2-1. Select “MSG INP <E>”.
3-1. Press the
[
] button.
3-2. Press and hold
[
BND] button for 1 second or
longer to clear the old message.
3-3. Press the [ , ] lever upward or down
-
ward to move the cursor.
3-4. Press the
[
BND] button to select a character.
Each time you press the [BND] button, the
character changes in the following orders:
Capital letters Numbers Symbols
Capital letters...
3-5. Turn the
[
ROTARY] knob to select the desired
character.
3-6. Repeat step 3- 3 to 3-5 to enter up to 30
characters for message.
3-7. Press and hold the
[
]
button for 2 seconds
or longer to store the message in memory
and cancel input message mode.
• Dimmer control
You can setting the dimmer control “ON” or
“OFF”.
∗ The factory default setting is “ON”.
2-1. Select “DIMMER”.
3-1. Turn the
[
ROTARY
]
knob to select “ON” or
“OFF”.
• Setting the method for title scroll
Set how to scroll in CD-TEXT, MP3/WMA title.
∗ The factory default setting is “ON”.
2-1. Select “AUTO SCROL”.
3-1. Turn the
[
ROTARY
]
knob to select “ON” or
“OFF”.
To change other settings
1. Press the
[
ADJ] bu tton to sw itch to the
adjustment selection display.
2. Press the
[ , ]
lever upward or downward
to select the “item name”.
Each time the
[ , ]
lever is pressed up/
down, the item display changes in the following
order:
“BLINK LED” “AMP CANCEL”
(“LINK ACT”
)
“LANGUAGE” “TEL-
SP” “TEL-SWITCH” “SYS CHK(E)”
3. Turn the
[
ROTARY] knob to select the “desired
setting item”.
∗ After completing settings, press the [ADJ] but-
ton to return to the previous mode.
• Anti-theft indicator
The red Anti-theft indicator is a function for preventing theft. When the DCP is removed from the
unit, this indicator blinks.
∗ The factory default setting is “OFF”.
2-1. Select “BLINK LED”.
3-1. Turn the
[
ROTARY
]
knob to select “ON” or
“OFF”.
• Setting the external amplifier
∗ The factory default setting is “OFF”.
2-1. Select “AMP CANCEL”.
3-1. Turn the
[
ROTARY
]
knob to select “ON” or
“OFF”.
• Setting the car speaker output for the
cellular phone
(
Optional BLT-433
)
∗ The factory default setting is “RIGHT”.
∗ To output the telephone calls, set the cellular phone
interrupt to ON.
2-1. Select “TEL-SP”.
3-1. Turn the
[
ROTARY
]
knob to select “RIGHT”
or “LEFT”.
• ON:
To scroll automatically.
• OFF:
To scroll just 1 time when the title was changed or the
[T]
button was pressed for 1 second or longer.
• ON:
Use with connected AMP.
• OFF:
Use with inside AMP.
• RIGHT:
Telephone calls can be heard on the front right
speaker connected to this unit.
• LEFT:
Telephone calls can be heard on the front left speaker
connected to this unit.
∗ Press and hold the [BND
]
button for 1 second
or longer to cancel the input message. Then
press and hold the [ ] button for 2 seconds
or longer to store the message and the mes
-
sage return to default setting.
27
English
DXZ368RMP
• MUTE:
The sound from this unit is muted during telephone
calls.
• ON:
You can listen to your telephone calls from the
speakers connected to this unit.
∗ When listening to your calls on your car speak-
ers, you can adjust the volume by turning the
[
ROTARY
]
knob.
• OFF:
This unit continues normal operation even when the
cellular phone is used.
Note:
• If connecting a hands-free kit, please ensure the
setting is ON to receive the telephone audio through
the system.
• Performing a system check
This function allows you to perform a system check
from the adjust mode when required.
2-1. Select “SYS CHK <E>”.
3-1. Press and hold the
[
] button for 1 second
or longer.
“SYSTEM CHK” appears in the display, then
the unit returns to the previous operation
mode.
1. Press the [SRC
]
button to select the mode you
want to enter a title
(
CD, CD changer or TV
)
.
2. Select and play a CD in the CD changer or tune
in to a TV station for which you want to enter
the title.
3. Press the
[D]
button and display the title
display.
4. Press and hold the
[T]
button for 1 second or
longer.
The display switches to the title input display.
5. Press the
[ , ]
lever upward or downward
to move the cursor.
6. Press the
[
BND
]
button to select a character.
Each time you press the
[
BND] button, the
character changes in the following order:
Capital letters Numbers Symbols
Umlaut Capital letters...
7. Turn the
[
ROTARY] knob to select the desired
character.
8. Repeat steps 5 to 7 to enter up to 10 characters
for the title.
9. Press and hold the
[
] button for 2 seconds
or longer to store the title into memory and
cancel title input mode.
Operations Common to Each Mode
• Triggered audio mute for cellular telephones
This unit requires special wiring to mute the audio
signal automatically when a cellular telephone
rings in the car.
∗ This function is not compatible with all cellular
telephones Contact your local authorized Clarion
dealer for information on proper installation and
compatibility.
∗ The factory default setting is “OFF”.
Entering titles
Titles up to 10 characters long can be stored in
memory and displayed for CD, CD changer and TV
stations. The number of titles that can be entered
for each mode are as follows.
• Cellular phone interrupt setting
If you connect this unit and your cellular phone with
a separately sold unit
(
BLT-433), you can listen to
your telephone calls on your car speakers.
∗ The factory default setting is “OFF”.
2-1. Select “TEL-SWITCH”.
3-1. Turn t h e
[
RO TA RY] k n ob t o sel e c t th e
setting. Each time you turn the [ROTARY]
knob, the setting changes in the following
order:
OFF ON MUTE OFF...
Mode Number of titles
CD mode 50 titles
TV mode 20 titles
CD changer mode Number of titles
DCZ628 connected 100 titles
CDC655Tz connected 100 titles
28
English
DXZ368RMP
Operations Common to Each Mode
Clearing titles
1. Select and play a CD in the CD changer or
tune in to a TV station for which you want to
clear the title.
2. Press the [D
]
button and display the title
display.
3. Press and hold the
[T]
button for 1 second or
longer.
The display switches to the title input display.
4. Press and hold the
[
BND
]
button for 1 second
or longer.
All characters in the title disappear.
5. Press and hold the
[
] button for 2 seconds
or longer to clear the title and cancel title input
mode.
29
English
DXZ368RMP
Note:
• The following operations are the same as for CD
mode:
∗ Pause
∗ Track selection
∗ Fast-forward/fast-backward
∗ Scan play
∗ Repeat play
∗ Random play
See “CD/MP3/WMA Mode Operations
”
(
page 20-
25) for details.
CD changer functions
When an optional CD changer is connected
through the CeNET cable, this unit controls all CD
changer functions. This unit can control a total of
2 changers.
Press the
[
SRC] button and select the CD changer
mode to start play. If 2 CD changers are con
-
nected, press the [SRC
]
button to select the CD
changer for play.
∗ If “NO MAG” appears in the display, insert the
magazine into the CD changer. “DISC CHECK” ap
-
pears in the display while the player loads
(
checks
)
the magazine.
∗ If “NO DISC” appears in the display, eject the maga-
zine and insert discs into each slot. Then, reinsert
the magazine back into the CD changer.
Note:
• Some CDs recorded in CD-R/CD-RW mode may
not be usable.
CAUTION
!
CD-ROM discs cannot be played from every CD
changer, itʼs depended on the model.
Displaying CD titles
This unit can display title data for CD-text CDs and
user titles input with this unit.
∗ Title data for CD-text CDs can be displayed with
this unit only when it is connected to CDC655Tz.
1. Press the [D] button to display the title.
2. Each time you press the [T
]
button, the title
display changes in the following order:
User title
(
disc) CD-text title (disc)
Artist name CD-text title (track) User
title (disc)...
Notes:
• If the CD playing is not a CD-text CD or no user
title has been input, “NO TITLE” appears in the
display.
• If a CD-text CD is not input its disc title or a track
title, “NO TITLE” appears in the display.
Procedure to scroll a title
Set “SCROLL” to “ON” or “OFF”.
(
The factory default setting is “
ON”. Refer to the
subsection “Turning the screen saver function
on or off” in section “Operation common to
each mode”.
)
• When set to “ON”
The title is automatically kept scrolling.
• When set to “OFF”
To scroll just 1 time when the title was changed
or the [T
]
button was pressed for 1 second or
longer.
Selecting a CD
Press the
[UP]
or [DN] button to select the desired
disc.
∗ If a CD is not loaded in a slot of magazine, press-
ing the [UP] or [DN] button can not work.
CD Changer Operations
7. OPERATIONS OF ACCESSORIES
30
English
DXZ368RMP
TV Operations
Note:
• The following operations are performed the same
as for radio mode:
∗ Channel selection
∗ Storing channels in memory
∗ Calling channels from memory
∗ Auto store
∗ Preset scan
See “Radio Mode Operations”
(
page 15-16) for details.
TV tuner functions
When an optional TV tuner is connected through
the CeNET cable, this unit controls all TV tuner
functions. To watch TV requires a TV tuner and
monitor.
Watching a TV
1. Press the
[
SRC] button and select the TV
mode.
2. Press the [BND
]
button to select the desired
TV band (TV1 or TV2). Each time the button is
pressed, the input selection toggles between
TV1 and TV2.
3. Press the
[ , ]
lever upward or downward
to tune in the desired TV station.
Watching a video
The TV tuner has a VTR input terminal to which 1
external device can be connected. Connect a 12
V video cassette player (VCP
)
or videocassette
recorder (VCR
)
to the TV tuner input terminal.
1. Press and hold the
[
ADJ
]
button for 1 second
or longer to select VTR.
2. To return to the TV broadcast, press and hold
the [ADJ
]
button for 1 second or longer.
Setting the TV area
When you select the TV area
(
TV reception area
)
,
the TV tuner area setting changes.
1. Press the
[
ADJ] bu tton to swit ch to the
adjustment selection display.
2. Press the
[
, ] lever upward or downward
to select “TV AREA <E>”.
3. Press the [ ] button.
4. Turn the
[
ROTARY] knob to select the reception
area.
Other various play functions
• Disc scan play
Disc scan play locates and plays the first 10
seconds of the first track on each disc in the
currently selected CD changer. This function
continues automatically until it is cancelled.
∗ Disc scan play is useful when you want to select a
desired CD.
1. Press and hold the [SCN
]
button for 1 second
or longer. “ALL...” and “SCN” light in the display
and disc scan play starts.
• Disc repeat play
After all the tracks on the current disc have been
played, disc repeat play automatically replays the
current disc over from the first track.
This function continues automatically until it is
cancelled.
1. Press and hold the
[
RPT
]
button for 1 second
or longer. “ALL...” and “RPT” light in the display
and disc repeat play starts.
• Disc random play
The disc random play selects and plays individual
tracks or discs automatically in no particular
order.
This function continues automatically until it is
cancelled.
1. Press and hold the
[
RDM
]
button for 1 second
or longer. “ALL...” and “RDM” light in the
display and disc random play starts.
• To cancel play
1. Press the operati n g but t o n pr e v i o u sly
selected.
CD Changer Operations
31
English
DXZ368RMP
• ON:
Sets the diver setting to ON.
5. Press the [ ] button.
6. Press the
[
ADJ] button to return to the previous
mode.
Setting the TV diver
You can change the reception setting for the TV
antenna connected to the TV tuner.
1. Press the
[
ADJ] bu tton to swit ch to the
adjustment selection display.
2. Press the
[ , ]
lever upward or downward
to select “TV DIVER”.
3. Turn the
[
ROTARY] knob clockwise to set to
“ON” or counterclockwise to set to “OFF”.
Digital Radio/DAB
Operations
DAB control function
When a CeNET cable is used to connect a DAB
(
DAH913 or DAH923
) (
sold separately), all
functions can be operated.
Listening to the DAB station
1. Press the
[
SRC] button to select the DAB
mode.
2. When the unit receives a DAB station, the
display changes in the following order:
Frequency channel Service label
Switching displays
1. Press the [D
]
button to select the desired
display.
2. Each time you press the
[D]
button, the display
switches in the following order:
S-LABL PTY CLOCK S-LABL ...
Notes:
• The display shown in the normal reception mode
and the preset reception mode is the same when
a DAB station is received.
• The number of programmes and broadcasting times
depend on the DAB stations.
• When the strength of DAB signals is weak, audio
output is muted.
Seek tuning
1. Press the
[
SRC] button to select the DAB
mode.
2. Press the
[ , ]
lever upward or downward
and hold in position for 1 second or longer.
∗ The main unit stops the seek tuning when it
cannot find a DAB station. The display returns
to the previous mode.
Manual tuning
1. Press the
[
SRC] button to select the DAB
mode.
2. Press and hold the
[
BND
]
button for 1 second
or longer. “
MANU” lights up in the display.
3. Press the
[ , ]
lever upward or downward
to select a station.
• OFF:
Sets the diver setting to OFF.
4. Press the
[
ADJ] button to return to the previous
mode.
TV Operations
32
English
DXZ368RMP
Recalling a preset programme
1. Press the
[
SRC] button to select the DAB
mode.
2. Press the [BND
]
button. Each time you press
the [BND
]
button, the display changes in the
following order:
[
M1] [M2] [M3] [M1]...
3. Press one of the
[
DIRECT
]
buttons to recall a
preset programme.
Note:
• Press and hold the
[
DIRECT
]
button for 2 seconds
or longer to store the programme currently being
received. (Manual memory
)
INFO (Announcement
)
In the INFO standby mode, when the selected
announcement programme starts, the main unit
switches to the selected announcement programme automatically.
• Setting the INFO standby mode
If you press and hold the
[TA]
button for 1 second
or longer, the main unit is set into the INFO
standby mode until the selected announcement
is broadcast. When the selected announcement
broadcast starts, the announcement item appears
in the display. If you press and hold the [TA
]
button for 1 second or longer while the selected
announcement broadcast is being received, the
selected announcement broadcast reception is
cancelled and the main unit goes into the INFO
standby mode.
• Cancelling INFO standby mode
To cancel the INFO standby mode, press and hold
the
[TA]
button for 1 second or longer.
• Information select
This is a function for selecting INFORMATION ON
or OFF in the Information interrupt mode.
You can set ON up to 6 information items.
∗ If no operation is performed for more than 7
seconds, manual tuning is cancelled and the
display returns to the previous mode.
Programme scan
This function scans through each receivable
programme in a DAB station being received for
10 seconds sequentially. This is useful when you
want to search for a desired programme.
1. Press the
[
SRC] button to receive a DAB
station.
2. Perform the following operation depending on
the connected model.
Press the
[
] button. “SCN” lights up and the
unit starts scanning each programme for 10
seconds sequentially.
Each time the main unit scans, the programme
name is shown in the display.
3. To stop programme scan when a desired
programme is tuned in.
Press the
[
] button.
Manual memory
The main unit has a manual memory function
for DAB programmes. Up to 18 programmes (6
programmes each
)
can be preset in the preset
buttons.
[M1], [M2]
and [M3
]
1. Press the
[
SRC] button to select the DAB
mode.
2. Press and hold the
[
BND
]
button for 1 second
or longer to select any one shown above.
3. Press the
[
, ] lever upward or downward
to select a desired programme.
4. Press and hold one of the [DIRECT
]
buttons
(
1 to 6) for 2 seconds or longer to store the
programme.
Switching programmes
1. Press the
[
SRC] button to receive a DAB
station.
2. Press the
[ , ]
lever upward or downward
to switch programmes in the DAB station.
Note:
• The programme name may be the same depend
-
ing on DAB programmes.
Digital Radio/DAB Operations
Note:
• The interrupt programme
(
PTY or INFO) cannot be
written into a manual memory.
33
English
DXZ368RMP
Digital Radio/DAB Operations
1. Perform the following operation depending on
the connected model.
Press and hold the
[
ADJ
]
button for 1 second
or longer to switch to the RDS adjustment
selection display.
2. Press the
[ , ]
lever upward or downward
to select “INFO-S <E>”, then press the
[
]
button to enter “INFO-S <E>” mode.
3. Press the
[ , ]
lever upward or downward
to select an information item. You can select
any of 6 items:
Travel Warning News Weather
Event Special Travel ...
4. Turn the
[
ROTARY] knob to set the information
item for ON or OFF.
5. Press the
[
] button to store the setting.
6. Press the
[
ADJ] button to return to the previous
display.
INFORMATION item
ENGLISH
Travel
Warning
News
Weather
Event
Special
Contents
Transport flash
Warning / Service
News flash
Area weather flash
Event announcement
Special event
For the following items, see “RDS Operations”
(
page 16
)
• AF function
∗ If the reception of the current broadcast station
deteriorates, “SEARCHING” appears in the display
and the radio searches for the same programme
on another frequency.
• TA
(
Traffic Announcement
)
• PTY
• Emergency broadcast
• Switching the PTY and INFO display
language
• Volume setting of TA, INFO emergency
broadcast (ALARM
)
and PTY
You can select any of the 6 items below:
34
English
DXZ368RMP
Replace with a fuse of the same amperage.
If the fuse blows again, consult your store of
purchase.
Consult your store of purchase.
Power does not turn on.
(
No sound is produced
)
No sound output when
operating the unit with
amplifiers or power
antenna attached.
ProblemCauseMeasure
Fuse is blown.
Incorrect wiring.
Power antenna lead is
shorted to ground or
excessive current is
required for remote-on
the amplifiers or power
antenna.
Nothing happens when
button are pressed.
Display is not accurate.
No sound heard.
The microprocessor has
malfunctioned due to
noise, etc.
DCP or main unit
connectors are dirty.
The speaker protection
circuit is operating.
General
1. Turn the unit off.
2. Remove all wires attached to the power
antenna lead. Check each wire for a possible
short to ground using an ohm meter.
3. Turn the unit back on.
4. Reconnect each amplifier remote wire to
the power antenna lead o ne by one. If
the amplifiers turn off before all wires are
attached, use an external relay to provide
remo te- on volt ag e
(
exce ssi ve curr en t
required).
Turn off the power, then press the
[
OPEN]
button and remove the DCP.
Press the reset button for about 2 seconds
with a thin rod.
Wipe the dirt off with a soft cloth moistened
with cleaning alcohol.
1. Turn down sound volume. Function can
also be restored by turning the power off
and on again. (Speaker volume is reduced
automatically when the speaker protection
circuit operates).
2. If the sound is muted again, consult our
service department.
8. TROUBLESHOOTING
35
English
DXZ368RMP
Troubleshooting
Write MP3/WMA files onto the disc properly.
Use MP3/WMA files encoded properly.
Use ISO9660 level 1, 2 or JOLIET or Romeo
file system.
Clean the disc with a soft cloth.
Replace with a disc with no scratches.
Use MP3/WMA files encoded properly.
Let dry for about 1 hour with the power on.
Use ISO9660 level 1, 2 or JOLIET or Romeo
file system.
No sound heard.
Sound skips or is noisy.
Sound is cut or skipped.
Noise is generated or
noise is mixed with
sound.
Sound is bad directly
after power is turned on.
Wrong filename
ProblemCauseMeasure
MP3/WMA files are
absent in a disc.
Files are not recognized
as an MP3/WMA file.
File system is not
correct.
Disc is dirty.
Disc is heavily scratched
or warped.
MP3/WMA files are not
encoded properly.
Water droplets may
form on the internal lens
when the car is parked
in a humid place.
File system is not
correct.
CD/MP3/WMA
36
English
DXZ368RMP
9. ERROR DISPLAYS
This is a failure of CD deckʼs mechanism and
consult your store of purchase.
Replace with a non-scratched, non-warpeddisc.
Eject the disc then reload it properly.
ERROR 2
Error DisplayCauseMeasure
A DISC is caught inside the CD
deck and is not ejected.
A DISC cannot be played due
to scratches,etc.
A DISC is loaded upside-down
inside the CD deck and does
not play.
CD/MP3/WMA
ERROR 3
ERROR 6
This is a failure of CD changerʼs mechanism
and consult your store of purchase.
Replace with a non-scratched, non-warped
disc.
Eject the disc then reload it properly.
ERROR 2
Error DisplayCauseMeasure
A CD inside the CD changer is
not loaded.
A CD inside the CD changer
cannot be played due to
scratches, etc.
A CD inside the CD changer
cannot be played because it is
loaded upside-down.
CD Changer
ERROR 3
ERROR 6
This is a failure of DVD mechanism and
consult your store of purchase.
Retry or replace with a non-scratched, nonwarped-disc.
Eject the disc then reload it properly.
ERROR 2
Error DisplayCauseMeasure
A DISC inside the DVD
changer cannot be played.
A DISC cannot be played due
to scratches, etc.
A DISC inside the DVD chang
er cannot be played because it
is loaded upside-down.
DVD Changer
ERROR 3
ERROR 6
Parental level error.
Region code error.
Set the correct Parental level.
Eject the disc and replace correct region code
disc.
ERROR P
ERROR R
37
English
DXZ368RMP
10. SPECIFICATIONS
FM tuner
Frequency Range: 87.5 MHz to 108 MHz
Usable Sensitivity: 11 dBf
50 dB Quieting Sensitivity: 17 dBf
Alternate Channel Selectivity: 75 dB
Stereo Separation (1 kHz): 35 dB
Frequency Response
(
±
3 dB): 30 Hz to 15 kHz
Audio
Maximum Power Output: 200 W (50 W X 4 ch
)
Power Output: 4 X 25 W (DIN 45324, +B=14.4 V
)
Bass Control Action (100 Hz): ±14 dB
Treble Control Action (10 kHz): ±14 dB
Line Output
(
with A/C 1 kHz, 10 k
Ω): 1.8 V
Notes:
• Specifications comply with JEITA Standards.
• Specifications and design are subject to change
without notice for further improvement.
• Please make sure when connecting external power
amplifier, that you properly, to the car chassis,
ground the amplifier.
• If this is not done, severe damage to the source unit
may happen.
General
Power Supply Voltage:
14.4 V DC (10.8 V to 15.6 V allowable), nega-
tive ground
Current Consumption: Less than 15 A
Speaker Impedance: 4 Ω (4 Ω to 8 Ω allowable
)
Weight: 2.42 lb.
(
1.1 kg
)
Dimensions:
178 mm Width X 50 mm Height X 152 mm
Depth
AM tuner
Frequency Range:
MW 531 kHz to 1602 kHz
LW 153 kHz to 279 kHz
Usable Sensitivity: 25 μV
CD player
System: Compact disc audio system
Usable Discs: Compact disc
Frequency Response: 10 Hz to 20 kHz
(
±
1 dB
)
Signal-to-Noise Ratio: 85 dB (1 kHz) IHF-A
Dynamic Range: 80 dB (1 kHz