Clarion DVS970Z, DVS9755Z Service Manual

- 1 -

DVS9755z/

DVS970Z

Published by Service Dept.

Printed in Japan

Clarion Co., Ltd.

22-3, Shibuya 2-chome, Shibuyaku, Tokyo, 150-8335 Japan
Service Dept.- 50 kamitoda,Toda-shi,Saitama,335-8511 Japan Tel: [phone] FAX:[phone]

298-5899-00

3.2001 B

Service Manual

Model

Model

DVD/CD Player/Multiple Channel
Processor

(PE-2360E)

(PE-2359B)
FOR U.S.A.
(PE-2359K)
FOR OTHER COUNTRIES

■SPECIFICATIONS

DVD player section

System: Digital Versatile Disc System with

CDDA Capable
Usable Discs: DVD Video Disc,Compact Disc
Frequency Response: 20 Hz to 20kHz (

±1dB)

S/N Ratio: 100dB
Dynamic Range: 100dB
Distortion: 0.01

％THD

Channel Separation: 80dB

Audio section

S/N Ratio: 100dB(digital input)

100dB(analog input)
Frequency characteristics:

20 Hz to 20kHz (

±1dB)

Separation: 90dB(digital input)

80dB(analog input)
High frequency distortion:

0.01

％(digital input)

0.01

％(analog input)

Analog output: 4.0Vrms(Vol Max.)
Analog input: 2.0Vrms(Max.)
Digital input: 44.1kHz sampling,

16-bit digital audio data
DSF: 6 modes
P.EQ: 3 bands

×2(front/rear independent)

Fo;20 Hz to 20kHz

1/3 octava steps

Q;1 to 20

G;

±12dB

Preset front; 6types
Rear; 7types
Subwoofer voltage gain;

＋12dB

(M.Vol Max.)
LPF Fo;50 Hz,80Hz,120Hz
LPF slope;12,18,24 dB/oct

General

Power supply voltage: DC14.4V(10.8 to 15.6V allowable)

Negative ground
Current consumption: Less than 3A
Dimensions(mm): 178(W)

×50(H)×165(D)

Weight: about 1.6kg

Remote control unit

Dimensions(mm): 47(W)×142(H)×32(D)
Weight: 30g(including battery)

※ Specifications and design are subject to change without

notice for further improvement.

■COMPONENTS

PE-2359B-A

DVD disc unit −−−−− 1
Control unit

−−−−− 1

Control unit cord 855-2464-00 1
Power supply harness 854-6377-50 1

 Fuse (3A) 120-0030-00 1

Parts bag(1) 921-9596-00 1

Set screw(M2.6x4) 714-2604-80 1
 Cord clamps(small) 321-1024-00 1

- 2 -

DVS9755z/

DVS970Z

c

c

 Double sided tape for brackets(30x140)

345-7030-00 1

Lead holder(L99) 335-0833-01 3
 Cord holder 321-1026-00 2
 Velcro tape(large A) 348-0327-00 2
 Velcro tape(small B) 348-0326-00 2
 M5 wing nuts 724-6000-11 4
 Installation bolt(M5x6) 714-5006-41 4
 Double sided tape for remo-con holder(25x50)

347-5559-00 1

 Installation bolt(M5x6 counter sunk)

716-1561-01 4

Parts bag(2) 921-9597-00 1

Hook plate 330-8216-01 2
 Side spring 750-2796-02 2
 Rubber cap 345-3653-20 1
 Rear bolt 716-0726-01 1
 Machine screw(M5x6) 714-5006-41 2

Bracket with bolt 300-9548-03 2
Main unit bracket 300-9683-01 2
Remote control RCB-037-130 1
Batteries for remote control(AAA)

−−−−− 2

Remote control holder 335-6146-00 1
Universal mounting bracket 300-9035-01 1
Strap 300-4976-00 1
Outer escutcheon 370-9006-03 1

PE-2359K-A,B

DVD disc unit −−−−− 1
Control unit

−−−−− 1

Control unit cord 855-2464-00 1
Power supply harness 854-6377-50 1

 Fuse (3A) 120-0030-00 1

Parts bag(1)

−−−−− 1
 Set screw(M2.6x4) 714-2604-80 1
 Cord clamps(small) 321-1024-00 1
 Double sided tape for brackets(30x140)

345-7030-00 1

Lead holder(L99) 335-0833-01 3
 Cord holder 321-1026-00 2
 Velcro tape(large A) 348-0327-00 2
 Velcro tape(small B) 348-0326-00 2
 M5 wing nuts 724-6000-11 4
 Installation bolt(M5x6) 714-5006-41 4
 Double sided tape for remo-con holder(25x50)

347-5559-00 1

 Installation bolt(M5x6 counter sunk)

716-1561-01 4

Parts bag(2)

−−−−− 1
 Hook plate 330-8216-01 2
 Side spring 750-2796-02 2
 Rubber cap 345-3653-20 1
 Rear bolt 716-0726-01 1
 Machine screw(M5x6) 714-5006-41 2

Parts bag(3) (only K-A)

−−−−− 1
 Ferrite core(small) 060-8041-00 1
 Ferrite core(large) 060-8042-00 2

Bracket with bolt 300-9548-03 2
Main unit bracket 300-9683-01 2
Remote control RCB-037-400 1
Batteries for remote control(AAA)

−−−−− 2

Remote control holder 335-6146-00 1
Universal mounting bracket 300-9035-01 1

Strap 300-4976-00 1
Outer escutcheon 370-9006-03 1

PE-2360E-A

DVD disc unit −−−−− 1
Control unit

−−−−− 1

Control unit cord 855-2464-00 1
Power supply harness 854-6377-50 1

 Fuse (3A) 120-0030-00 1

Parts bag(1) 921-9600-00 1

Set screw(M2.6x4) 714-2604-80 1
 Cord clamps(small) 321-1024-00 1
 Double sided tape for brackets(30x140)

345-7030-00 1

Lead holder(L99) 335-0833-01 3
 Cord holder 321-1026-00 2
 Velcro tape(large A) 348-0327-00 2
 Velcro tape(small B) 348-0326-00 2
 M5 wing nuts 724-6000-11 4
 Installation bolt(M5x6) 714-5006-41 4
 Double sided tape for remo-con holder(25x50)

347-5559-00 1

 Installation bolt(M5x6 counter sunk)

716-1561-01 4

Parts bag(2) 921-9622-00 1

Ferrite core(small) 060-8041-00 1
 Ferrite core(large) 060-8042-00 2

Bracket with bolt 300-9548-03 2
Main unit bracket 300-9683-01 2
Remote control RCB-037-400 1
Batteries for remote control(AAA)

−−−−− 2

Remote control holder 335-6146-00 1
Universal mounting bracket 300-9035-01 1
Strap 300-4976-00 1
Outer escutcheon 370-9006-03 1

■NOTE

※ We cannot supply PWB with component parts in prin-

ciple. When a circuit on PWB has failure , please repair
it by component parts base. Parts which are not men­tioned in service manual are not supplied.

※ This product incorporates copyrigh protection technol-

ogy that is protected by methon claims of certain
U.S.patents and other intellectual property rights
owners.Use of this copyright protection tecnology must
be authorized by Macrovision Corporation,and is in­tended for home and other limited viewing uses only
unless otherwise authorized by Macrovision Corporation.

Reverse engineering or disassembly is prohibited.

※ Manufactured under license from dolby Laboratories.

"Dolby","Pro Logic"and duble-D symbol are tradmarks
of Dolby Laboratories.
Works.

○1992-1997 Dolby Laboratories,Inc.All rights

reserved.

※ Manufactured under license from Digital Theater

Systems,Inc.US Pat.5,451,942 5,956,674 5,974,380
5,978,762 and other world-wide patents issusd and pend­ing.
"DTS"and"DTS Digital surround"are registered tradmarks
of Digital Theater Systems,Inc.

○1996,2000 Digital The-

ater Systems,Inc.All Rights Reserved.

※ Prevent damage caused by static electricity when re-

pairing the pick-up.
The pattern of the pick-up is short-circuiting for preven-

- 3 -

DVS9755z/

DVS970Z

■ To engineers in charge of repair or

inspection of our products.

Before repair or inspection, make sure to follow
the instructions so that customers and Engineers
in charge of repair or inspection can avoid suf­fering any risk or injury.

1. Use specified parts.
The system uses parts with special safety features against
fire and voltage. Use only parts with equivalent charac­teristics when replacing them.
The use of unspecified parts shall be regarded as re­modeling for which we shall not be liable. The onus of
product liability (PL) shall not be our responsibility in cases
where an accident or failure is as a result of unspecified
parts being used.

2. Place the parts and wiring back in their original positions
after replacement or re-wiring.
For proper circuit construction, use of insulation tubes,
bonding, gaps to PWB, etc, is involved. The wiring con­nection and routing to the PWB are specially planned
using clamps to keep away from heated and high voltage
parts. Ensure that they are placed back in their original
positions after repair or inspection.
If extended damage is caused due to negligence during
repair, the legal responsibility shall be with the repairing
company.

3. Check for safety after repair.
Check that the screws, parts and wires are put back se­curely in their original position after repair. Ensure for
safety reasons there is no possibility of secondary

tion.

Remove the soldering with a solder iron whose insula­tion resistance is larger than 10M

Ω(DC500V) after com-

plete connection to the main PWB
For repair table shall use copper or conductive sheet
(with impedance is lower than 1G

Ω)such as a sheet.

Be sure to put on a wrist-strap for prevent electric
static's.(with impedance lower than 100M

Ω) The strap

works to drain away the static electricity build-up on the
human body.
And as static electricity build-up on clothes is not drained
away, be careful and not your clothes to touch the pick­up.
Position of short soldering for pick-up protection posi­tion is different by model.
Some units have two short soldering points.
Always short LD circuit to open the short circuit and re­moves by soldering iron.

This appliance contains a laser system and is classified as
a "CLASS 1 LASER PRODUCT".To use this model
properly,read this Owner's Manual carefully and keep this
manual for your future reference.In case of any trouble with
this player,please contact your nearest "AUTHORIZED ser­vice station".To prevent direct exposure to the laser beam,do
not try to open the enclosure.

■CAUTION

This equipment has been tested and found to comply with
the limits for a Class B digital device, pursuant to Part 15 of
the FCC Rules.These limits are designed to provide rea­sonable protection against harmful interference in a resi­dential installation.This equipment generates,uses,and can
radiate radio frequency energy and,if not installed and used
in accordance with the instructions,may cause harmful in­terference to radio communications.However,there is no
quarantee that interference will not occur in a particular
installation.If this equipment does cause harmful interfer­ence to radio or television reception,which can be deter­mined by turning the equipment off and on,the user is en­couraged to consult the dealer or an experienced radio/TV
technician for help.

Top View of model

Top View of model

- 4 -

DVS9755z/

DVS970Z

ploblems around the repaired spots.
If extended damage is caused due to negligence of re­pair, the legal responsibility shall be with the repairing
company.

4. Caution in removal and making wiring connection to the
parts for the automobile.
Disconnect the battery terminal after turning the ignition
key off. If wrong wiring connections are made with the
battery connected, a short circuit and/or fire may occur.
If extensive damage is caused due to negligence of re­pair, the legal responsibility shall be with the repairing
company.

5. Cautions regarding chips.
Do not reuse removed chips even when no abnormality
is observed in their appearance. Always replace them
with new ones. (The chip parts include resistors, capaci­tors, diodes, transistors, etc). The negative pole of tanta­lum capacitors is highly susceptible to heat, so use spe­cial care when replacing them and check the operation
afterwards.

6. Cautions in handling flexible PWB
Before working with a soldering iron, make sure that the
iron tip temperature is around 270

℃. Take care not to

apply the iron tip repeatedly(more than three times)to the
same patterns. Also take care not to apply the tip with
force.

7. Turn the unit OFF during disassembly and parts replace­ment. Recheck all work before you apply power to the
unit.

8. Cautions in checking that the optical pickup lights up.
The laser is focused on the disc reflection surface through
the lens of the optical pickup. When checking that the
laser optical diode lights up, keep your eyes more than
30cms away from the lens. Prolonged viewing of the la­ser within 30cms may damage your eyesight.

9. Cautions in handling the optical pickup
The laser diode of the optical pickup can be damaged by
electrostatic charge caused by your clothes and body.
Make sure to avoid electrostatic charges on your clothes
or body, or discharge static electricity before handling the
optical pickup.

9-1. Laser diode

The laser diode terminals are shorted for transpor­tation in order to prevent electrostatic damage.
After replacement, open the shorted circuit. When
removing the pickup from the mechanism, short
the terminals by soldering them to prevent this
damage.

9-2. Actuator

The actuator has a powerful magnetic circuit. If a
magnetic material is put close to it. its characteris­tics will change. Ensure that no foreign substances
enter through the ventilation slots in the cover.

9-3. Cleaning the lens

Dust on the optical lens affects performance. To
clean the lens, apply a small amount of isopropylalcohol
to lens paper and wipe the lens gently.

■ERROR DISPLAYS

If an error display other than the ones described above appears,press the reset botton.If the problem
persists,turn off the power.

If an error occurs,one of the following displays is displayed.
Take the measures described below to eliminate the problem.

Error Display

Cause

Measure

ERROR 2

ERROR 3

ERROR 6

A DVD/CD is caught inside the DVD deck
and is not ejected.

A DVD/CD cannot be played due to
scratches,etc.

A VDV/CD is loaded upside-down inside the
DVD deck and does not play.

This is a failure of DVD deck's mechanism.

Replace with a non-scratched,non-warped-disc.

Eject the disc then reload it properly.

Reset botton.

- 5 -

DVS9755z/

DVS970Z

■BLOCK DIAGRAM

- 6 -

DVS9755z/

DVS970Z

■EXPLANATION OF IC

pin 65 : DVD/CD : O : Disk distinction signal output.
pin 66 : LAYER : O : DVD type signal output (single layer/

dual layer).
pin 67 : PREVENT : IN : Prevent Japan.
pin 68 : CHUCK SW_ : IN : Chucking switch signal input.
pin 69 : TR A : IN : Photo sensor signal input.
pin 70 : TR B : IN : Photo sensor signal input.
pin 71 : TR C : IN : Photo sensor signal input.
pin 72 : NU : - : Not in use.
pin 73 : NU : - : Not in use.
pin 74 : NU : - : Not in use.
pin 75 : NU : - : Not in use.
pin 76 : MA_ : O : MA.
pin 77 : NU : - : Not in use.
pin 78 : NU : - : Not in use.
pin 79 : A 8 : O : Address output.
pin 80 : A 7 : O : Address output.
pin 81 : A 6 : O : Address output.
pin 82 : A 5 : O : Address output.
pin 83 : A 4 : O : Address output.
pin 84 : A 3 : O : Address output.
pin 85 : A 2 : O : Address output.
pin 86 : A 1 : O : Address output.
pin 87 : A 0 : O : Address output.
pin 88 : READ_ : O : Reading strobe signal output.
pin 89 : WRITE_ : O : Writing Strobe signal output.
pin 90 : NU : - : Not in use.
pin 91 : VSS : - : Negative supply voltage.
pin 92 : TK 0 : IN : Test mode key input.
pin 93 : TK 1 : IN : Test mode key input.
pin 94 : TK 2 : IN : Test mode key input.
pin 95 : TK 3 : IN : Test mode key input.
pin 96 : TM 1 : IN : Test mode selectionion input.
pin 97 : TM 2 : IN : Test mode selectionion input.
pin 98 : LIMIT SW : IN : Inside limit switch signal for the disk.
pin 99 : NU : - : Not in use.
pin100 : Vref : - : Reference voltage

052-5042-00 M30622MCA-E53GP DVD Player controller

1.Terminal Description
pin 1 : NU : - : Not in use.
pin 2 : NU : - : Not in use.
pin 3 : EJECT KEY _ : IN : Eject key switch input. Negative logic.
pin 4 : NU : - : Not in use.
pin 5 : REMOCON : IN : Remote controller signal input terminal.
pin 6 : BYTE_ : IN : Connect to VSS.
pin 7 : CN VSS_ : IN : Connect to VSS.
pin 8 : INIT 1 : IN : Destination setting input. Ref. Table 1.
pin 9 : INIT 2 : IN : Destination setting input. Ref. Table 1.
pin 10 : RESET_ : IN : Reset signal input. Negative logic.
pin 11 : X OUT : O : Crystal connection.
pin 12 : VSS : - : Negative supply voltage.
pin 13 : X IN : IN : Crystal connection.
pin 14 : VCC : - : Positive supply voltage.
pin 15 : NU : - : Not in use.
pin 16 : ACC DET : IN : ACC detect signal input. "H"= ACC

ON.
pin 17 : B/U OFF DET_ : IN : Backup voltage OFF signal input.
pin 18 : POWER KEY_ : IN : Power Key interrupt signal input.
pin 19 : 27pinCONNECT: IN : Connect to pin 27.
pin 20 : DIR SI : IN : Serial data input from the digital-audio-

interface-receiver.
pin 21 : DIR SO : O : Serial data output to the digital-audio-

interface-receiver.
pin 22 : NU : - : Not in use.
pin 23 : DIR CL : O : Clock pulse output to the digital-audio-

interface-receiver.
pin 24 : DIR CE : O : Chip enable pulse output to the digital-

audio-interface-receiver.
pin 25 : A IN SEL : O : RCA= "L", Ce-NET= "H"
pin 26 : V I/O SEL : O : External input = "H"
pin 27 : IE BUS RX : IN : IE Bus communication line.

052-5041-02 TMP95CW64F-3A88(Z) DVD Mechanizm controller

1.Terminal Description
pin 1 : Vref : - : Reference voltage
pin 2 : A VSS : - : Analog ground.
pin 3 : A VCC : - : Positive supply voltage for the internal

analog section.
pin 4 :NU : - : Not in use.
pin 5 :NU : - : Not in use.
pin 6 : NMI_ : IN : Connect to pin-7.
pin 7 : EJECT : IN : Eject signal input. Negative logic.
pin 8 : A MUTE : O : Audio mute signal output.
pin 9 : SYS P 1 : O : Power supply-1 control signal output.
pin 10 :NU : - : Not in use.
pin 11 : RESET OUT_ : O : Reset signal output.
pin 12 : T SCAN 0 : O : Test mode scan output.
pin 13 : T SCAN 1 : O : Test mode scan output.
pin 14 : T SCAN 2 : O : Test mode scan output.
pin 15 : T SCAN 3 : O : Test mode scan output.
pin 16 : MCW : O : Loading motor control output.
pin 17 : MCCW : O : Loading motor control output.
pin 18 :NU : - : Not in use.
pin 19 :NU : - : Not in use.
pin 20 : CS 0_ : O : Chip selection signal output.
pin 21 : CS 1_ : O : Chip selection signal output.
pin 22 :NU : - : Not in use.
pin 23 : M MUTE : O : M MUTE.
pin 24 :NU : - : Not in use.
pin 25 : VCC : - : Positive supply voltage.
pin 26 : VSS : - : Negative supply voltage.
pin 27 : X 1 : - : Crystal connection.
pin 28 : X 2 : - : Crystal connection.
pin 29 : EX ACCESS_ : IN : External access selection.
pin 30 : RESET : IN : Reset signal input. Negative logic.
pin 31 : ACC CONT : IN : ACC control signal input.
pin 32 :NU : - : Not in use.
pin 33 : TIME : O : Loading time & Eject time control out-

put.
pin 34 : FGPULSE : IN : FG pulse input.
pin 35 :S BRAKE : O : Brake command output to the disk-mo-

tor.
pin 36 :NU : - : Not in use.
pin 37 : DSP INT : IN : Interrupt signal input.
pin 38 :NU : - : Not in use.
pin 39 : PLL A : O : PLL control output.
pin 40 : PLL B : O : PLL control output.
pin 41 : M INT_ : IN : Interrupt signal input.
pin 42 :NU : - : Not in use.
pin 43 : AT RESET : O : Reset signal output.
pin 44 : VCC : - : Positive supply voltage.
pin 45 : D 0 : I/O :Data input / output.
pin 46 : D 1 : I/O :Data input / output.
pin 47 : D 2 : I/O :Data input / output.
pin 48 : D 3 : I/O :Data input / output.
pin 49 : D 4 : I/O :Data input / output.
pin 50 : D 5 : I/O :Data input / output.
pin 51 : D 6 : I/O :Data input / output.
pin 52 : D 7 : I/O :Data input / output.
pin 53 :RS : O : Test mode LCD driver control RS.
pin 54 :R/W : O : Test mode LCD driver control R/W.
pin 55 :E : O : Test mode LCD driver control E.
pin 56 :NU : - : Not in use.
pin 57 :DB 4 : I/O : Test mode LCD driver control DB.
pin 58 :DB 5 : I/O : Test mode LCD driver control DB.
pin 59 :DB 6 : I/O : Test mode LCD driver control DB.
pin 60 :DB 7 : I/O : Test mode LCD driver control DB.
pin 61 : AM 8 : O : Connect to VCC.
pin 62 : VSS : - : Negative supply voltage.
pin 63 : VCC : - : Positive supply voltage.
pin 64 : BUSY : O : Busy flag output.

- 7 -

DVS9755z/

DVS970Z

pin 33 : DISP DO : O : Serial data output to the LCD driver.
pin 34 : DISP DI : IN : Serial data input from the LCD driver.
pin 35 : DISP CLK : O : Clock pulse output to the LCD driver.
pin 36 : DISP CE : O : Chip enable signal output to the LCD

driver.
pin 37 : NU : - : Not in use.
pin 38 : DIRF 0 : O : Sample frequency select signal output.
pin 39 : DEC P OFF_ : IN : Power off admission signal input from

RISC CPU.
pin 40 : DIRF 1 : O : Sample frequency select signal output.
pin 41 : DEC SYS ACC : O : SYS-ACC output of RISC CPU.
pin 42 : DIRF 2 : O : Sample frequency select signal output.
pin 43 : DEC RST IN_ : IN : Reset request from RISC IC.
pin 44 : DIR RESET_ : O : Reset pulse output to the digital-audio-

interface-receiver.
pin 45 : DIR EMPHA : IN : Pre-emphasis selection.
pin 46 : DIR AUDIO : IN : PCM audio data = "L", Others = "H".
pin 47 : MECH 5V REM : O : 5V and 3.3V power supply control for

the mechanism.
pin 48 : 2.5 V REM : O : ACC 2.5V power supply control.
pin 49 : 3.3 V REM : O : ACC 5V and ACC 3.3V power supply

control.
pin 50 : DAC MC : O : Colck pulse output to the DAC.
pin 51 : DD 15 CONT : O : Power supply control output for the au-

dio sections.
pin 52 : DD 3.3 CONT : O : ACC 5V, ACC 3.3V, ACC 2.5V power

supply control.
pin 53 : DAC ML : O : Latch pulse output to the DAC.
pin 54 : 10 V REM : O : 10V power supply control for DVD

mechanism.
pin 55 : DAC MDI : O : Serial data output to the DAC.
pin 56 : DAC RESET_ : O : Reset pulse output to the DAC.
pin 57 : VOL STB : O : Strobe pulse output to the Electric vol-

ume or the digital-audio-interface-re-

ceiver.
pin 58 : VOL DATA : O : Serial data output to the electric vol-

ume IC.
pin 59 : VOL CLOCK : O : Serial data clock output for the electric

volume IC.
pin 60 : VCC : - : Positive supply voltage.
pin 61 : DIR ERR : IN : digital-audio-interface-receiver error de-

tection.
pin 62 : VSS : - : Negative supply voltage.
pin 63 : DSP RESET_ : O : Reset pulse output to DSP IC.
pin 64 : DSP 0V : IN : Sub DSP over flow detection.
pin 65 : ADC RESET_ : O : Reset pulse output to the ADC.
pin 66 : ADC 0V : IN : ADC over flow detection.
pin 67 : VIDEO MUTE_ : O : Video muting signal output.
pin 68 : AMP REM OUT: O : Amplifier ON signal output terminal.
pin 69 : NU : - : Not in use.
pin 70 : NU : - : Not in use.
pin 71 : DIR X STATE_ : IN : digital-audio-interface-receiver/PLL un-

lock detection.
pin 72 : AMP REM DT_ : IN : Remote controller wire short detection.
pin 73 : Speed pulse_ : IN : Speed pulse input.
pin 74 : SYS MUTE_ : O : System mute signal output. Negative

logic.
pin 75 : LINE MUTE_ : O : Mute signal output for Audio signal of

Ce-NET. Negative logic.
pin 76 : EJECT OUT_ : O : Eject command output.
pin 77 : NU : - : Not in use.
pin 78 : NU : - : Not in use.
pin 79 : DVD RESET_ : O : Reset pulse output to DVD mechanism.
pin 80 : DVD A MUTE_ : IN : Mute request input from DVD mecha-

nism.
pin 81 : DVD ACC CNT : O : DVD mechanism ACC-CONT.
pin 82 : DVD SYS P-1 : IN : From DVD mechanism.
pin 83 : REG 1 : IN : Region code input.
pin 84 : REG 2 : IN : Region code input.
pin 85 : REG 3 : IN : Region code input.
pin 86 : NU : - : Not in use.

pin 87 : KEY A/D : IN : Input terminal of A/D converter for Key

judgment. Ref. Table 2.
pin 88 : NTSC/PAL_ : IN : NTSC = "H", PAL = "L".
pin 89 : DECK BB_ : IN : Initial setting input, DVD deck = "H"
pin 90 : STND ALONE_ : IN : Stand alone = "L", Ce-NET slave =

"H".
pin 91 : PKB : IN : "H"= Parking brake ON
pin 92 : DSP CSB_ : O : Sub DSP chip selection output.
pin 93 : DSP CS_ : O : DSP chip selection output.
pin 94 : A VSS : - : Analog ground.
pin 95 : NU : - : Not in use.
pin 96 : Vref : - : Reference voltage
pin 97 : A VCC : - : Positive supply voltage for the internal

analog section.
pin 98 : DSP SI : IN : Serial data input from the DSP IC.
pin 99 : DSP SO : O : Serial data output to the DSP IC.
pin100 : DSP SCK : O : Clock pulse output to the DSP IC.

Table 1. Destination setting input

North Third

America area Japan Europe
INITIAL 1 ( pin 8 ) H L H L
INITIAL 2 ( pin 9 ) L L H H

Table 2. Input of A/D converter for Key judgment ( pin 87 )

Judgment A/D steps
Power key 0/255 to 25/255
With Controller 205/255 to 238/255
Without Controller 239/255 to 255/255

pin 28 : IE BUS TX : O : IE Bus communication line.
pin 29 : DEC TX : O : Transmit terminal to RISC CPU.
pin 30 : DEC RX : IN : Receive terminal from RISC CPU.
pin 31 : DEC RSTX_ : O : Reset pulse output to RISC CPU.
pin 32 : DEC REQ : IN : Request signal input from RISC CPU.

- 8 -

DVS9755z/

DVS970Z

Note)Several different parts of the same reference number are alternative parts.

One of those parts is used in the set.

NO. PART NO. DESCRIPTION Q'TYNO. PART NO. DESCRIPTION Q'TY

Note)Some parts depend on each model.The model name is specified in the description.

■EXPLODED VIEW・PARTS LIST

Control unit

1 373-0946-00 DIAL COVER(PE-2359) 1

373-0946-20 DIAL COVER(PE-2360)
2 370-5917-00 ESCUTCHEON 1
3 382-6024-00 BUTTON(POW,ADJ,SOU) 1
4 382-6025-00 BUTTON(DSF,AMOD) 1
5 382-6026-00 BUTTON(VOL-D,L) 1
6 382-6027-00 BUTTON(MUT,ENT) 1
7 382-6028-00 BUTTON(R) 1
8 382-6029-00 BUTTON(VOL-U) 1
9 347-6428-00 FILM 2

10 347-6429-00 FILM 1
11 347-6430-00 FILM 1
12 290-7920-00 LABEL(2359B) 1

290-8007-00 LABEL(2359K)

290-7920-00 LABEL(2360E)

13 378-0516-00 BADGE(clarion) 1
14 335-6420-00 ILLUMI PLATE 1
15 716-0872-01 PAD SCREW(M1.7×6) 3
16 001-7040-01 LED(WHITE) 3
17 379-1191-41 INDICATOR 1

18 001-7046-00 LED(WHITE) 1
19 331-2809-01 LCD COVER 1
20 347-6169-00 SHADE 1
21 347-6480-00 REFLECTOR 1
22 335-6213-00 ILLUMI PLATE 1
23 335-6209-00 LCD HOLDER 1
24 335-6216-00 LED HOLDER 1
25 345-8273-00 RUBBER CONNECTOR 1
26 345-8274-00 RUBBER CONNECTOR 1
27 855-8000-02 MINI DIN CORD 1
28 335-6419-00 REAR COVER 1
29 013-6507-50 SWITCH 11
30 716-0872-11 PAD SCREW(M1.7×6BLK) 4
31 039-1833-00 SWITCH PWB 1

(WITHOUT COMPONENT)
32 345-8605-00 CAP 4
33 347-6475-00 SHADE 1
34 060-4005-02 IR RECEIVER 1

- 9 -

DVS9755z/

DVS970Z

DVD disc unit

24

44