Citizen Peeler CL-S6621 User Manual

PEELER CL-S6621

User’s Manual

Contents

CAUTION ...................................................................................... 3

1 Function ............................................................................... 4

1-1 Exterior view and part names ........................................4

2 Main specications of peeler ........................................... 5

3 Checking items inside the accessory box ...................... 6

4 Peeler setting ...................................................................... 7

4-1 Peeler door opening/closing ..........................................7

4-2 Media loading ......................................................................7

4-3 Peeler setting .......................................................................7

5 Initial value of peeling position ....................................... 8

6 Peeler commands ............................................................... 9

7 Adjust the peel sensor ..................................................... 10

CITIZEN is a registered trademark of CITIZEN WATCH CO., Japan.
CITIZEN es una marca registrada de CITIZEN WATCH CO., Japón.

Company names and product names in this manual are trademarks or registered

trademarks of relevant companies.

Copyright ©2016 by CITIZEN SYSTEMS JAPAN CO., LTD.

-2-

CAUTION

z Always use the peeler with the door closed except when the media is

loaded into the peeler.

z Do not push down the door roughly when it is opened, which may cause

damage to the hinge of the door.

z Use the media that meets standard requirements. If not, the liner and label

may be jammed in the peeler.

z Wipe o dirt or glue stuck to the peeler with a soft cloth soaked in a neutral

detergent.

z Do not use volatile liquids such as benzine and thinner, which may cause

the roller rubber and plastic parts to deteriorate.

-3-

1 Function

Peeling Roller

Idle Roller (upper)

This peeler unit is designed to automatically remove the label from the liner.

1-1 Exterior view and part names

Release Knob

Peeling Sensor

Door (Closed)

Friction Roller (lower)

Door (Open)

Inside of the peeler unit

-4-

2 Main specications of peeler

Direction of media feed

Width of liner (a) : 1.97 – 7 in (50 – 177.8 mm)

Minimum length of label (b) : 1 in (25.4 mm)

Label: ne media/Thickness: 0.09 mm
(including glue layer)/Rolled inwards

Minimum width of label (c) : Label must be positioned at 1.4 in

(10.16 mm) from left edge of liner, which is
viewed from front of media exit

Maximum width of label : To be narrower than liner

Thickness of label : 0.0067 in (0.17 mm) or less

Thickness of liner : 0.0027 in (0.07 mm) or less

Inner diameter of roll media : 3 in (76 mm) or more

Durability : 20 km or 200,000 peeled labels (when using the

label above)

Peeling position accuracy : ±1.5 mm

Peeling position varies depending on the type of
media, the size of roll media and the size of ink
ribbon, so adjust it to the optimum condition as
needed

a

c

b

-5-

3 Checking items inside the accessory box

User's Manual

You should check that all of the following items are inside the accessory box.
If any are missing, please contact your supplier.

PEELER ...............................................................................................................................................1 piece

COVER FRONT FOR PEELER .......................................................................................................1 piece

Screws .............................................................................................................................................4 pieces

Installation Guide .........................................................................................................................1 piece

User’s Manual ................................................................................................................................1 piece

Screw (4)

PEELER

Installation Guide

COVER FRONT FOR PEELER

-6-

4 Peeler setting

4-1 Peeler door opening/closing

1 Opening

Shift the release knob of the peeler to the left with the nger, and the peeler door will

open.

2 Closing

Push up the peeler door until it clicks closed.

4-2 Media loading

1 First peel o the labels with a length of 12 cm (5 inch) or more on the top of the

loading media, then load the media into the peeler where the rst label comes to
the peeling sensor. Close the print head of the printer.

2 Open the peeler door and pass the liner between the peeling roller and the peeler

door and close the door.

4-3 Peeler setting

To use this peeler, select the peeler function from the menu stored in a nonvolatile
memory in the printer. To change the setting item in a memory, execute it in the
VuePrint mode that is the menu setting contents printing.

Note: For details about the VuePrint mode, see the user’s manual of the printer (CD-

ROM).

The CL-S6621 has the menu “AutoCongure“ set to ON when shipping from the
factory. In this ON condition, if the peeler is installed on the printer, the menu
“Function Select” will be automatically changed to “Peel On.” But if the O condition
occurs, select the “Peel On” in the following manner. (For details of menu setting,
refer to the operation manual of each printer.)

 Setting the peeler function in the menu setup mode

1 Prior to entering the menu mode, load media into the printer. (For details about

the media loading, see the user’s manual of the printer.)

2 Hold in the MODE/REPEAT key and at the same time turn on the power to the

printer and the printer will be placed into the menu mode, where the PRINT LED
and the CONDITION LED will light up.

3 In the VuePrint mode, performs the printing of menu setting contents until the

sub-menu FUNCTION SELECT of the After Print shows up. In that state, select the
Peel On.

Note: After selecting the peeler function, feed the media to the peeling position

by pressing the FEED key. After this, the media, once printed, automatically
advances towards the peeling position and there the label is peeled o.

-7-

5 Initial value of peeling position

If the peeler function is selected when the power is turned on or the resetting is
performed, the media will automatically feed from the reference point to the peeling
position (by initial value of feeding amount), regardless of printer emulation.
To nely adjust the peeling position, transmit the command STX f or STX Kf from
the host computer to the printer. In this case, each command initial value being set
designates the zero (0) of peeling position, and the peeling position shifts front or
back by the parameter of each command. (For details, see the separate Command
Reference.)

<Each command initial value>
Emulation DM4 : 68.6 mm (2.70 in)
Emulation DMI : 12.7 mm (0.50 in)
Emulation DPP : 37.1 mm (1.46 in)

<Example of making ne adjustments>
STX f (nnn)
When the emulation is set to DM4, the peeling position shifts from zero (0) to

frontward position by 0.01 inch. In this case, the command is STX f (271).

The distance between the peeler sensor or platen center and the peeling position is
shown below.

Middle point
between labels

10.76 mm
(0.42 in)

Peeling plate

Note: The measurements shown here are examples.

35.4 mm (1.39 in)

Center of platen

-8-

24.64 mm (0.97 in)

Label

Liner

Sensor position

6 Peeler commands

The following are the peeler commands. For details of each command, see the
separate Command Reference.

Peeling position designated command STX f, STX Kf

This command designates the feeding amount from the reference point to the peeling
position.

Software switch setting command STX V

The peeler function can be temporarily turned ON or OFF by transmitting this
command to the printer while turning on the power to the printer.
Note: If the label is at peeling position when the peeler function is selected, the
medial will not feed even if the Feed key is pressed. In this case, remove the label rst.

-9-

7 Adjust the peel sensor

(1) Open the top cover.

(2) Remove the screw (1) fastening the cable cover, and push down the section

indicated by the arrow (1) . While holding the section down, push inward (toward
the rear of the machine) to release (2) , and then lift and remove the cable cover
(3). Take care that the screw does not fall inside the printer chassis.

Cable cover

1

3

2

-10-

(3) Adjust the peel sensor.

1 Remove the label backing on the

paper sheet (mounting board) pulled
out, and pass the mounting board
through the peeler unit.

2 Close the peeler unit.
3 First, the peel sensor knob will need to

be turned all the way to the minimum
setting. Using a screwdriver, turn
the knob counter-clockwise all the
way around until it can be turned no
farther.

3

4 With the label ejected from the printer facing up and raised so that it is 10 mm

from the sensor, turn the knob clockwise little by little. Continue adjusting the
position of the knob to the point where the LED turns on.

LED

4

4

10mm

-11-

363 V

an Ness Way, Suite 404

T
T
Fax:
http://www

Otto-Hirsch-Brücken 17
70329 Stuttgar
Ger
T
Fax:
http://www

6-1-12, T
T
T
Fax:
http://www

orrance, CA 90501. USA
el: [phone]

[phone]

.citizen-systems.com

many United Kingdom

el: [phone] Tel: [phone]

[phone] Fax: [phone]

okyo, 188-8511. Japan
el: [phone]

anashi-cho, Nishi-Tokyo-shi

[phone]

Elizabeth House, 56-60 London Road

t Staines-Upon-Thames, TW18 4HF

.citizen-europe.com

.citizen-systems.co.jp

PXZ00086-10

PMC-1609