Citizen PEELER CL-E700 series User Manual

PEELER

USER’S MANUAL

For CL-E700 Series

I – 2

Contents

CAUTION ............................................................................ I-3

1 Function .............................................................................I-4

1-1 Exterior view and part names ..................................... I-4

2 Main specications of peeler .........................................I-5

3 Checking items inside the accessory box ....................I-6

4 Peeler setting ....................................................................I-7

4-1 Peeler door opening/closing ....................................... I-7

4-2 Media loading ................................................................... I-7

4-3 Peeler setting ....................................................................I-7

5 Initial value of peeling position ..................................... I-8

6 Peeler commands .............................................................I-9

CITIZEN is a registered trademark of CITIZEN WATCH CO., Japan.
CITIZEN es una marca registrada de CITIZEN WATCH CO., Japón.

Company names and product names in this manual are trademarks or

registered trademarks of relevant companies.

Copyright ©2016 by CITIZEN SYSTEMS JAPAN CO., LTD.

I – 3

CAUTION

z Always use the peeler with the door closed except when the media is

loaded into the peeler.

z Do not push down the door roughly when it is opened, which may cause

damage to the hinge of the door.

z Use the media that meets standard requirements. If not, the liner and label

may be jammed in the peeler.

z Wipe o dirt or glue stuck to the peeler with a soft cloth soaked in a neutral

detergent.

z Do not use volatile liquids such as benzine and thinner, which may cause

the roller rubber and plastic parts to deteriorate.

I – 4

1 Function

This peeler unit is designed to automatically remove the label from the liner.

1-1 Exterior view and part names

Peeling Roller

Idle Roller (upper)

Friction Roller (lower)

Top view of door opened

Door

Top view

Front view

Peeling Sensor

Release Knob

Side view

I – 5

2 Main specications of peeler

Width of liner (a) : 25.4  118 mm (1  4.65 in)

Minimum length of label (b) : 25.4 mm (1 in)

Label: ne media/Thickness: 0.09 mm (0.0035 in)
(including glue layer)/Rolled inwards

Maximum length of label : Approx. 120 mm (4.72 in)

However it will change depending on the
environment of the media exit and the type of
media used.

Minimum width of label (c) : Label must be positioned at 16  22 mm

(0.63  0.87 in) from left edge of liner, which is
viewed from front of media exit.

Maximum width of label : To be narrower than liner

Thickness of label : 0.17 mm (0.0067 in) or less

Thickness of liner : 0.07 mm (0.0027 in) or less

Inner diameter of roll media : 76 mm (3 in) or more

Durability : 20 km (when using the label above)

Peeling position accuracy : ±1.5 mm

Peeling position varies depending on the type of
media, the size of roll media and the size of ink
ribbon, so adjust it to the optimum condition as
needed.

c

a

b

Direction of media feed

I – 6

3 Checking items inside the accessory box

You should check that all of the following items are inside the accessory box.
If any are missing, please contact your supplier.

PEELER ...............................................................................................................................................1 piece

Screws ..............................................................................................................................................2 pieces

Installation Guide ..........................................................................................................................1 piece

User’s Manual ..................................................................................................................................1 piece

Screw (2)

Installation Guide

User's Manual

PEELER

I – 7

4 Peeler setting

4-1 Peeler door opening/closing

1 Opening

Shift the release knob of the peeler to the left with the nger, and the peeler door

will open.

2 Closing

Push down the left end of the peeler door until it clicks closed.

4-2 Media loading

1 First peel o the labels with a length of 12 cm (5 inch) or more on the top of the

loading media, then load the media into the peeler where the rst label comes to
the peeling sensor. Close the print head of the printer.

2 Open the peeler door and pass the liner between the peeling roller and the peeler

door and close the door.

4-3 Peeler setting

To use this peeler, set the peeler function ON that is one of the various setting items in
a nonvolatile memory in the printer.

To change the setting of the peeler function, execute it in the printer congurations
setting mode from the control panel or use the command STX KD.

The CL-E700 series has the menu “AutoCongure“ set to ON when shipping from
the factory. In this ON condition, if the peeler is installed on the printer, the menu
“Function Select” will be automatically changed to “Peel On.” But if the O condition
occurs, select the “Peel On” in the following manner. (For details of menu setting,
refer to the operation manual of each printer.)

 Selecting the “Peel ON” in the menu setup mode

1 In a condition that the “Ready” is displayed on the control panel, press the MENU

key and the printer will be placed into the printer conguration setting mode.

2 Press the Feed key twice rst and then the Stop key.
3 Press the Feed key and the menu “Function Select” will be displayed.
4 Press the Stop key and the current function select item will be displayed.
5 Press the Feed key 1-3 times until the “Peel On” is displayed.
6 Press the Stop key and the current contents will be stored in the memory.

If turn o the power, the printer will return to the original menu item. If the current
setting data is required to be stored permanently, perform the “Save Settings”
operation, referring to Chapter 2 in the User’s Manual of the printer.

Note: After selecting the peeler function, feed the media to the peeling position

by pressing the Feed key. After this, the media, once printed, automatically
advances towards the peeling position and there the label is peeled o.

I – 8

5 Initial value of peeling position

If the peeler function is selected when the power is turned on or the resetting is
performed, the media will automatically feed from the reference point to the peeling
position (by initial value of feeding amount), regardless of printer emulation.
To nely adjust the peeling position, transmit the command STX f or STX Kf from
the host computer to the printer. In this case, each command initial value being set
designates the zero (0) of peeling position, and the peeling position shifts front or
back by the parameter of each command. (For details, see the separate Command
Reference.)

<Each command initial value>
Emulation DM4 : 68.6 mm (2.70 in)
Emulation DMI : 12.7 mm (0.50 in)
Emulation DPP : 37.1 mm (1.46 in)

<Example of making ne adjustments>
STX f (nnn)
When the emulation is set to DM4, the peeling position shifts from zero (0) to

frontward position by 0.01 inch. In this case, the command is STX f (271).

The distance between the peeler sensor or platen center and the peeling position is
shown below.

35.4 mm (1.39 in)

10.76 mm
(0.42 in)

Center of platen

24.64 mm (0.97 in)

Middle point
between labels

Label

Liner

Sensor position

Peeling plate

Note: The measurements shown here are examples.

I – 9

6 Peeler commands

The following are the peeler commands. For details of each command, see the
separate Command Reference.

Peeling position designated command STX f, STX Kf

This command designates the feeding amount from the reference point to the peeling
position.

Software switch setting command STX V

The peeler function can be temporarily turned ON or OFF by transmitting this
command to the printer while turning on the power to the printer.

Note: If the label is at peeling position when the peeler function is selected, the

media will not feed even if the Feed key is pressed. In this case, remove the
label rst.

363 V

an Ness Way, Suite 404

T

orrance, CA 90501. USA

T

el: [phone]

Fax:

[phone]

http://www

.citizen-systems.com

Otto-Hirsch-Brücken 17

Elizabeth House, 56-60 London Road

70329 Stuttgar

t Staines-Upon-Thames, TW18 4HF

Ger

many United Kingdom

T

el: [phone] Tel: [phone]

Fax:

[phone] Fax: [phone]

http://www

.citizen-europe.com

6-1-12, T

anashi-cho, Nishi-Tokyo-shi

T

okyo, 188-8511. Japan

T

el: [phone]

Fax:

[phone]

http://www

.citizen-systems.co.jp

PXZ00122-10

PMC-1609