Citizen E812 Abbreviated Instruction
English
• This watch is solar-powered. Expose the dial to light and use it sufficiently charged.
• To see details of charging time, specifications and operations, refer to the instruction manual:
E812 Abbreviated instruction
E812 instruction manual
Component identification
Function hand/
Chronograph minute hand
Minute hand
Hour hand
24-hour hand
Alarm indication (ON/
Chronograph second hand
• Actual appearance may differ from the illustration.
• The crown has two positions when pulling it out.
OFF)
Second hand/
Mode hand
A
Button
Date indication
Crown
B
Button
Crown's position
0 1 2
Changing the mode
This watch features four different modes: [TME] (time/calendar), [CHR]
(chronograph/reference position correction), [L-TM] (local time), and [ALM]
(alarm).
Push the crown in to position 0.
1.
Rotate the crown.
2.
The mode hand moves and the mode is changed.
Setting the calendar
Push the crown in to position 0.
1.
Rotate the crown to change the mode to [TME].
2.
Pull the crown out to position 1.
3.
The current setting of the year and mouth is indicated.
Function hand: year since leap year
Second hand: month
Rotate the crown counterclockwise to set the date indication.
4.
• When you rotate the crown quickly, the date indication will move
continuously. To stop the rapid movement, rotate the crown.
• The date indication changes to the first day of the next month after finishing
setting if you set a non-existing day.
Press and release the upper right button A and lower right
5.
button
• Button A changes the year setting indicated by the function hand.
• Button
Year indication
“Year” corresponds to the years since
leap year and is indicated with markers
in the figure below.
Each number means year since leap
ye ar.
B
repeatedly to adjust the year and the month.
B
changes the month setting indicated by the second hand.
Month indication
“Month” corresponds to one of the 12
markers in the figure below.
Each number means month.
Setting the time
Push the crown in to position 0.
1.
Rotate the crown to change the mode to [TME].
2.
Pull the crown out to position 2.
3.
The second hand stops at 0 second.
Rotate the crown to set the time.
4.
• Check AM/PM of the time referring to the 24-hour hand.
• When you rotate the crown quickly, the hand will move continuously. To
stop the rapid movement, rotate the crown.
Push the crown in to position 0 in accordance with a reliable
5.
time source to finish the procedure.
The second hand starts moving.
Push the crown in to position 0 to finish the procedure.
6.
The second hand moves to indicate the current second.
1/3
E812 Abbreviated instruction
Using the chronograph
• Measuring up to 60 minutes in 1/20 second increments.
• The hour, minute and 24-hour hands move normally during chronograph
measurement.
Push the crown in to position 0.
1.
Rotate the crown to change the mode to [CHR].
2.
The chronograph second hand moves to 0 second and the chronograph
minute hand moves to 0 minute and they stop.
A
Start/stop: press button
• The chronograph minute hand indicates the 1/20 second units by pressing
and holding button
return the hand to minute indication.
Reset: press button
• Be sure to reset chronograph after finishing measurement.
.
B
while chronograph is stopped. Release the button to
A
while the chronograph is stopped.
Using the local time
When the mode is changed to [L-TM], the time for another region separate from
the current time (local time) is displayed.
• The time difference can be set up to ±23 hours (in 1 hour units) based on the
time set in [TME] mode.
• The minute and second hands show the same time as that in [TME].
Displaying the local time
Push the crown in to position 0.
1.
Rotate the crown to change the mode to [L-TM].
2.
Local time is indicated.
Setting the time difference
Using the alarm
Push the crown in to position 0.
1.
Rotate the crown to change the mode to [ALM].
2.
Hour, minute and 24-hour hands indicate the current alarm time setting and
the second hand indicates the current alarm setting (“ON” or “OFF”).
Pull the crown out to position 2.
3.
The alarm setting is automatically turned to “ON”.
Rotate the crown to set the alarm time.
4.
• Check AM/PM of the alarm time referring to the 24-hour hand.
• When you rotate the crown quickly, the hands will move continuously. To
stop the rapid movement, rotate the crown.
• The alarm time cannot be set based on the local time.
Push the crown in to position 0 to finish the procedure.
5.
To set the alarm ON/OFF
While in the [ALM] mode, pull the crown out to position 1 or 2 and press
A
button
Press button A or B.
The alarm sounds for 15 seconds.
Press and hold button A in the [ALM] mode while the crown is in the position 0.
The alarm tone can be monitored.
.
To stop alarm
To check the alarm sound
Pull the crown out to position 2 when the mode hand points [L-
1.
TM].
Rotate the crown to set the time difference.
2.
• Rotate the crown counterclockwise when the time difference to set is minus.
Rotate the crown clockwise when the time difference to set is plus.
• If the hour hand passes the midnight during the setting, the date indication
will be advanced by 1 day. It takes some time to complete the date indication
to be advanced.
Push the crown in to position 0 to finish the procedure.
3.
2/3
Loading...