Citizen 6850 Instruction Manual
Setting Instructions for
Movement Caliber 6850
Contents
1. Main Components
2. Mode Change-Over
3. Before Using
4. How to Set and Operate Each Mode
1. Hand movement demonstration
2. Setting the Time (TME mode)
3. Setting the Calendar (CAL mode)
4. Setting the Quick-Set Alarm (AL-1 mode)
5. Setting the Daily Alarm (AL-2 mode)
6. Stopwatch Operation (CHR mode)
7. Setting the Timer (TMR mode)
8. Setting the Local Time ( L-TM mode)
9. Monitoring in the Normal Time Mode
10. All-Reset Function
11. Calculation Operations
5. Specifications
Care of Your Timepiece.
6.
(click on a topic)
1 MAIN COMPONENTS
Return to Table of Contents
2 MODE CHANGE-OVER
Push the (M)
modes as shown
Note:
Always check the mode hand to ensure the watch is set in the desired mode durin
guse, since pressing the (M)(lower right) button unknowingly during operation may
occur
(lower right)
button in the normal position to switch between
Return to Table of Contents
g
Return to Table of Contents
3. BEFORE USE
Before use, follow the procedures below to ensure that all watch components are
in proper working order:
Confirm the Zero position setting:
x All hands, except the mode
hand, move to the ‘0’ position
x The 24-hour hand is
synchronized with the
hour/minute hands
ZERO POSITION SETTING
Each hand positioned as listed below confirms the
‘0’ position setting is correct:
Hour Hand 0 hour
Minute Hand 0 Minutes
Second Hand 0 Seconds
24-Hour Hand 0 hour
Auxiliary Hand 0 minutes
If the watch hands are not positioned as above,
follow the Zero Position Setting procedures to
ensure proper use.
1. Pull the (M) button out to the first step
position
Push the (A) button to set the second hand
to the 0 second position
Push the (B) button to set the Auxiliary
feature hand to the 0 hour position
Push the (C) button to set the hour, minute
and 24-hour hands to the 0 hour, 0 minute
position
2. Be sure to push the (M) button in to its
normal position. This completes the Zero
Position Setting
Press and hold down the (A), (B), or (C)
buttons to activate the quick-advance
feature
A stron
Return to Table of Contents
shock may cause the hands to move
g
Return to Table of Contents
4. HOW TO SET AND OPERATE EACH MODE
1. HAND MOVEMENT DEMONSTRATION
Pushing of the (A), (B) and (C)
button at once will cause the
second, minute and auxiliary
feature hands to stop in the ‘0’
position after moving through the
followin
Minute Hand: (1)+5min ->(2) –10min -> (3) +5min
Second Hand: (1)+5sec ->(2) –10sec -> (3) +5sec
Aux. Hand. : (1)+5 ->(2) –10 -> (3) +5
stages.
Return to Table of Contents
Return to Table of Contents
2.SETTING THE TIME
Changing the time from 10:10:15 to 19:20:00
<(M) button in the normal position>
x The hour/minute hand is based on the 12-hour clock system. Use the 24-hour
hands as a reference under normal time setting procedures to determine
morning or afternoon times
Setting Procedures
Resetting the second hand
x Pressing the (A) button while the
second hand is between 0-29 seconds
will not alter the minute hand
position
x Pressing the (A) button while the
second hand is between the 30-59
seconds position will advance the
minute hand to the next full minute
position
Return to Table of Contents
Return to Table of Contents
Push the (M) button in to the normal position
Press and hold down either the (B) and (C)
buttons to use the quick-advance feature
Quick-advance function: Hand movement is about
twice as fast after the first revolution.
(clockwise movement only)
The hour/minute/24-hour hands are synchronized
3. SETTING THE CALENDAR (CAL)
Changing the calendar from May 5 to Sept. 9.
<(M) button normal position)
(May 5)
Automatic Calendar System
The calendar feature on this watch requires
no adjustment at the end of the month.
Adjustment for Feb 29 during a leap year
Return to Table of Contents
p
Return to Table of Contents
Setting Procedures
Press and hold down either the (A) or (B) button for the quick-advance feature.
The month and date must be independently set.
<Press the (M) button in to the normal position>
Automatic Calendar Correction System
When a non-existent date is entered, the
watch will automatically set the date to
the 1
st
of the following month when the (M)
button is pushed in to the normal position.
Exam
le: Feb 30 -> March 1st
Return to Table of Contents
Loading...