Casio CTK2100ES1A User Manual

USER’S GUIDE
Please keep all information for future reference.
Safety Precautions Before trying to use the keyboard, be sure to read the separate “Safety Precautions”.
GUÍA DEL USUARIO
Guarde toda información para tener como referencia futura.
Precauciones de seguridad
Antes de intentar usar el teclado, asegúrese de leer las “Precauciones de seguridad” separadas.
ES
EnglishEspañol
CTK2100ES1A
NOTICE
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
FCC WARNING
Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
Declaration of Conformity
Model Number: CTK-2100 Trade Name: CASIO COMPUTER CO., LTD. Responsible party: CASIO AMERICA, INC. Address: 570 MT. PLEASANT AVENUE, DOVER, NEW JERSEY 07801 Telephone number: 973-361-5400 This device complies with Part 15 of the FCC Rules, Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
Important!
Please note the following important information before using this product.
• Before using the optional AD-5 Adaptor to power the unit, be sure to check the AC Adaptor for any damage first. Carefully check the power cord for breakage, cuts, exposed wire and other serious damage. Never let children use an AC adaptor that is seriously damaged.
• Never attempt to recharge batteries.
• Do not use rechargeable batteries.
• Never mix old batteries with new ones.
• Use recommended batteries or equivalent types.
• Always make sure that positive (+) and negative (–) poles are facing correctly as indicated near the battery compartment.
• Replace batteries as soon as possible after any sign they are getting weak.
• Do not short-circuit the battery terminals.
• The product is not intended for children under 3 years.
• Use only CASIO AD-5 adaptor.
• The AC adaptor is not a toy.
• Be sure to disconnect the AC adaptor before cleaning the product.
Manufacturer:
This mark applies in EU countries only.
CASIO COMPUTER CO.,LTD. 6-2, Hon-machi 1-chome, Shibuya-ku, Tokyo 151-8543, Japan
Responsible within the European Union: CASIO EUROPE GmbH Casio-Platz 1, 22848 Norderstedt, Germany
Company and product names used in this manual may be registered trademarks of others.
Any reproduction of the contents of this manual, either in part or its entirety, is prohibited. Except for your own,
personal use, any other use of the contents of this manual without the consent of CASIO is prohibited under copyright laws.
IN NO EVENT SHALL CASIO BE LIABLE FOR ANY DAMAGES WHATSOEVER (INCLUDING, WITHOUT LIMITATION, DAMAGES FOR LOSS OF PROFITS, BUSINESS INTERRUPTION, LOSS OF INFORMATION) ARISING OUT OF THE USE OF OR INABILITY TO USE THIS MANUAL OR PRODUCT, EVEN IF CASIO HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.
The contents of this manual are subject to change without notice.
Contents
General Guide ............................. E-2
Using the 10-key Pad (bn) ..................................... E-4
Using the Setting Button (
)................................. E-4
3
Getting Ready to Play ................ E-5
Preparing the Music Stand ..................................... E-5
Power Supply ......................................................... E-5
Playing the Digital Keyboard..... E-6
Turning on Power and Playing ............................... E-6
Using Headphones................................................. E-6
Using the Voice Pads ............................................. E-7
Using the Metronome ............................................. E-7
Controlling the
Keyboard Sounds....................... E-9
Select from a variety of musical
instrument sounds .................................................. E-9
Using Reverb........................................................ E-10
Using a Pedal ....................................................... E-10
Changing the Pitch (Transpose, Tuning).............. E-11
Sampling a Sound and Playing It on the
Keyboard (Sampling) ............................................ E-11
Using a Sampled Sound in a Rhythm
(Drum Assign)....................................................... E-14
Music Challenge
Keyboard Game ........................ E-25
Using Auto Accompaniment
Playing the Rhythm Part Only .............................. E-27
Playing All Parts ................................................... E-28
Using Auto Accompaniment Effectively................ E-30
Using One-Touch Preset ...................................... E-31
Connecting External Devices
Connecting a Computer........................................ E-32
MIDI Settings ........................................................ E-33
Connecting to Audio Equipment........................... E-35
..... E-27
..... E-32
Reference................................... E-36
Troubleshooting.................................................... E-36
Specifications ....................................................... E-38
Operating Precautions .......................................... E-39
Song List............................................................... E-40
Chord Example List .............................................. E-41
MIDI Implementation Chart
English
Playing Built-in Songs ............. E-15
Playing the Demo Songs...................................... E-15
Playing Back a Particular Song ............................ E-15
Using Built-in Songs to
Master Keyboard Play .............. E-19
Phrases ................................................................ E-19
Step Up Lesson Flow ........................................... E-19
Selecting the Song, Phrase, and
Part You Want to Practice .................................... E-20
Lessons 1, 2, and 3 .............................................. E-21
Lesson Settings .................................................... E-22
Using Auto Step Up Lesson ................................. E-23
Included Accessories
Music Stand
Song Book
Leaflets
• Safety Precautions
• Appendix
• Other (Warranty, etc.)
Items included as accessories are subject to change without notice.
Separately Available Accessories
• You can get information about accessories that are separately for this product from the CASIO keyboard catalog available from your retailer, and from the CASIO website at the following URL.
http://world.casio.com/
E-1
General Guide
• In this manual, the term “Digital Keyboard” refers to the CTK-2100.
• In this manual, buttons and other controllers are identified using the numbers shown below.
1
2345
789 bmbk bl6
bn
cs ct
E-2
bo bp bq br bs bt ck cl cm
cn co cp cq cr cn
General Guide
POWER switch E-6
1
VOLUME slider E-6
2
SETTING button E-4
3
SAMPLING button E-11, 12, 14
4
METRONOME, BEAT button E-7
5
INTRO, REPEAT button E-16, 17, 22, 30
6
NORMAL/FILL-IN, REW button E-16, 20, 27, 30
7
VARIATION/FILL-IN, FF button E-16, 20, 30
8
SYNCHRO/ENDING, PAUSE button E-16, 30, 31
9
START/STOP, PLAY/STOP button
bk
E-15, 16, 18, 21, 22, 27
ACCOMP ON/OFF, CHORDS, PART SELECT
bl
button E-15, 18, 20, 22, 28, 34
TEMPO buttons ☞E-8, 17, 31
bm
Number buttons, [–]/[+] buttons ☞E-4
bn
SONG BANK button E-15, 17, 20, 25
bo
RHYTHM, ONE TOUCH PRESET button
bp
E-7, 9, 27, 31
TONE button E-6, 9
bq
VOICE PAD1, LISTEN button E-7, 12, 21
br
VOICE PAD2, WATCH button E-7, 12, 21
bs
VOICE PAD3, REMEMBER button E-7, 12, 22
bt
VOICE PAD4, NEXT button E-7, 12, 20
ck
VOICE PAD5, AUTO button E-7, 12, 23
cl
SET SELECT, MUSIC CHALLENGE button
cm
E-7, 25
Speakers
cn
Song Bank list
co
Rhythm list
cp
Display
cq
Tone list
cr
CHORD root names ☞E-28
cs
Percussion instrument list ☞E-9
ct
English
USB port E-32
dk
dk
dl dm dn do
SUSTAIN jack E-10
dl
PHONES/OUTPUT jack E-6, 35
dm
AUDIO IN jack E-11, 35
dn
DC 9V terminal E-5
do
E-3
General Guide
Using the 10-key Pad (bn)
Use the number buttons and the [–] and [+] buttons to change the settings of the parameters that appear in the upper left area of the display.
Setting
Mde r nPno
Number Buttons
Use the number buttons to enter numbers and values.
• Enter the same number of digits as the currently displayed value. Example: To enter tone number 005, input 0 3 0 3 5.
• Negative values cannot be input using the number buttons. Use [+] (increase) and [–] (decrease) instead.
[–] and [+] Buttons
You can use the [+] (increase) and [–] (decrease) buttons to change the displayed number or value.
• Holding down either button scrolls the displayed setting.
• Pressing both buttons at the same time will revert to the initial default setting or the recommended setting.
Using the Setting Button (3)
Use the Setting button ( select the reverb type, pedal effect, etc.
1.
Press 3.
) to access settings that let you
3
Setting
T r a n s .
Parameter
2.
Next press 3 until the parameter whose setting you want to change is displayed.
Each press of 3 cycles through the available parameters.
Parameter Display See Page
1 Transpose Trans. E-11
2 Accompaniment Volume AcompVol E-31
3 Song Volume Song Vol E-17
4 Tuning Tune E-11
5 Reverb Reverb E-10
6 Voice Fingering Guide Speak E-22
7 Note Guide NoteGuid E-23
8 Performance Evaluation Scoring E-23
9 Phrase PhraseLn E-23
10 Sampling Start SmplAuto E-13
11 Keyboard Channel Keybd Ch E-33
12 Navigate Channels Navi. Ch E-33
13 Local Control Local E-34
14 Accomp Out AcompOut E-34
15 Pedal Effect Jack E-10
E-4
3.
When the parameter you want is displayed, use
(10-key) to change its setting.
bn
• The parameter setting will disappear from the upper left area of the screen if you do not perform any operation for some time.
• The tone and other parameters revert to their initial defaults whenever you turn on power (page E-6).
Getting Ready to Play
Preparing the Music Stand
Music stand
Power Supply
Either an AC adaptor or batteries can be used to power this Digital Keyboard. Normally, use of AC adaptor power is recommended.
• The AD-5 AC adaptor does not come with this Digital Keyboard. Purchase it separately from your retailer. See page E-1 for information about options.
Using the AC Adaptor
Use the AD-5 AC adaptor when you want to power the Digital Keyboard from a household electrical outlet.
AD-5DC 9V terminal
Household power outlet
Using Batteries
• Be sure to turn off power before loading batteries.
• It is up to you to prepare six commercially available AA-size batteries. Do not use oxyride batteries or any other nickel based batteries.
1.
Open the battery cover on the bottom of the Digital Keyboard.
2.
Load six AA-size batteries into the battery compartment.
Make sure the positive + and negative - ends of the batteries are facing as shown in the illustration.
3.
Insert the tabs of the battery cover into the holes on the side of the battery compartment, and close the cover.
Tabs
English
• Be sure to turn off Digital Keyboard power before connecting or disconnecting the AC adaptor.
Low Battery Indication
The indicator shown below starts to flash to let you know when battery power is low. Replace the batteries with new ones.
Low battery indicator (flashes)
E-5
Playing the Digital Keyboard
11 22 55
Turning on Power and Playing
1.
Turn on 1.
This turns on power.
2.
Try playing something on the keyboard. Use 2 to adjust volume.
Increase
Decrease
bnbn
cmcm
clcl
ckck
btbt
bmbm
bpbp
bqbq
Using Headphones
Using headphones cuts off output from the built-in speakers, which means you can practice playing even late at night without disturbing others.
• Be sure to turn down the volume level before connecting headphones.
brbr
bsbs
PHONES/OUTPUT jack
• Turning off the keyboard power causes all current settings and sampled sounds (page E-11) to be cleared. The keyboard will revert to initial default settings the next time you turn it on.
Auto Power Off (Using Batteries)
While you are using batteries for power, power will turn off automatically if you do not perform any operation for about six minutes. Auto Power Off is disabled while the AC adaptor is being used for power.
Disabling Auto Power Off
You can disable Auto Power Off to ensure that power is not turned off automatically during a concert, etc.
1.
While holding down bq, turn on power.
Auto Power Off will be disabled.
E-6
• Headphones do not come with the Digital Keyboard.
• Use commercially available headphones. See page E-1 for information about options.
• Do not listen to very high volume output over headphones for long period. Doing so creates the risk of hearing damage.
• If you are using headphones that require an adaptor plug, make sure you do not leave the adaptor plugged in when removing the headphones.
Playing the Digital Keyboard
Using the Voice Pads
You can use the voice pads to sound various sound effects or even sounds you have sampled (“Sampling”, page E-11). Use the voice pads to add something extra to your performances.
1.
Press bp.
Lights
2.
Press a pad (1 through 5, br through cl) to sound what is assigned to it.
There are four sets of voice pad sounds numbered 1 through 4 (see below). Each press of the sound sets 1 through 4.
br bs bt ck cl cm
Pad 1Pad 2Pad 3Pad 4Pad 5
TONE 402
Set 1
“VOICE PAD 1”
Set 2 Set 1 sounds with various pitches.
Set 3 Set 1 sounds repeated.
Set 4 XIAO LUO GUNSHOT BONGO CONGA
*1: Pad 5 plays original sound raised a perfect fifth. *2: Pad 1: Up a perfect fifth; Pad 2: Down a perfect fifth;
Pad 3: Same as Set 1; Pad 4: Up a major third; Pad 5: Down a perfect fifth
*3: Pads 1 and 5: Gradually rising pitch;
Pad 2: Gradually falling pitch
TONE 403
“VOICE
PAD 2”
*3
TONE 404
“VOICE PAD 3”
*2
cycles thorough
cm
TONE 401 “ORIGINAL”
TAMBOURINE
*1
Sounding Sampled Sounds with the Voice Pads
Sampling sounds will change the tones assigned to sets 1 through 3 to the sampled sounds. For more information, see page E-11.
Using the Metronome
The metronome lets you play and practice along with a steady beat to help keep you on tempo.
Start/Stop
1.
Press 5.
This starts the metronome.
This pattern changes with each beat.
2.
Press 5 again to stop the metronome.
Changing the Beats Per Measure
You can configure the metronome to use a bell sound for the first beat of each measure of the song you are playing.
• You can specify 0, or a value from 2 to 6 as the number of beat per measure.
• When playing a built-in song, the beats per measure setting (which determines when the bell sounds) is configured automatically for the currently selected song.
1.
Hold down 5 until the beats per measure setting screen appears on the display.
Bea t
English
Example: When Set 2 is selected
P a d S e t
• While a sound set number is displayed, you can change it using few seconds after the indicator appears, the display will return to the previous screen automatically.
(10-key). If you do not perform any operation for a
bn
• If you do not perform any operation for after the beats per measure setting screen appears, the display will return to the screen displayed before you pressed
2.
Use bn (10-key) to enter the number of beats per measure.
• The bell will not sound if you specify 0 for this setting. In this case, all beats are indicated by a click sound. This setting lets you practice with a steady beat, without worrying how many beats there are in each measure.
5
E-7
.
Playing the Digital Keyboard
Changing the Metronome Tempo
Use the following procedure to change the tempo of the metronome.
1.
Press bm.
Use y (slower) and t (faster) to change the tempo setting. Holding down either button changes the setting at high speed.
•Pressing y and t at the same time will initialize the
tempo setting in accordance with the currently selected song or rhythm.
•Pressing display. While the tempo value is flashing, you can use
(10-key) to change it.
bn
Note that you must input leading zeros, so 89 is input as 089.
• The tempo value will stop flashing if you do not perform any operation for a short while.
Tempo value (flashes)
causes the tempo value to flash on the
bm
Changing the Metronome Sound Volume
The metronome volume setting is changed automatically with the volume level of the currently selected Auto Accompaniment or song. The metronome volume cannot be adjusted independently.
• For information about changing the Auto Accompaniment volume, see page E-31.
• For information about changing the song volume, see page E-17.
• You cannot adjust the balance between the metronome and note volume during Auto Accompaniment and built-in tune play.
E-8
Controlling the Keyboard Sounds
33
Select from a variety of musical instrument sounds
Your Digital Keyboard lets you select tones for a wide variety of musical instrument sounds, including violin, flute, orchestra, and more. Even the same song sound takes on a different feel by changing the instrument type.
To select an instrument for playing
1.
Press bq.
Tone number
44
bnbn
clcl
ckck
btbt
brbr
bsbs
bqbq
bpbp
3.
Try playing something on the keyboard.
The tone of the instrument you selected will sound.
Playing with a Piano Tone (Piano Setup)
1.
Press bp and bq at the same time.
This selects the grand piano tone.
English
S t . G r P n o
Tone name
2.
Use bn (10-key) to select the tone number you want.
The corresponding tone number and tone name will appear on the screen.
• See the separate “Appendix” for a complete list of available tones.
• You also can find out instrument numbers using the tone groups printed on the Digital Keyboard’s console.
• Use the number buttons to enter the tone number. Specify three digits for the tone number. Example: To select 001, enter 0 3 0 3 1.
• When one of the drum sets is selected (tone numbers 395 through 400), each keyboard key is assigned a different percussion sound.
Settings
Tone Number: “001” Reverb: “06” Transpose: 00 Pedal Effect: SUS Rhythm Number: “131” Accompaniment: Rhythm part only Local Control: On Drum Assign: Off
E-9
Controlling the Keyboard Sounds
Using Reverb
Reverb adds reverberation to notes. You can change the duration of the reverb.
1.
Press 3 a number of times until “Reverb” appears on the display (page E-4).
Reverb
2.
Use the bn (10-key) [–] and [+] keys to select the reverb setting you want.
Off (oFF) Turns off reverb. 1 to 10 The larger the number selected, the longer
the reverb duration.
Indicator disappears when reverb is turned off.
R e v e r b
Using a Pedal
A pedal can be used to change notes in various ways while playing.
• A pedal unit does not come with the Digital Keyboard. Purchase one separately from your retailer. See page E-1 for information about options.
Connecting a Pedal Unit
Connect an optional pedal unit.
SUSTAIN jack
Selecting the Pedal Effect
1.
Press 3 a number of times until “Jack” appears on the display (page E-4).
J a c k
2.
Use the bn (10-key) [–] and [+] keys to select the pedal effect you want.
• The following shows the available pedal effects.
Sustain (SUS)
Sostenuto (SoS)
Soft (SFt)
Rhythm (rHy)
Sustains notes played while the pedal is depressed. Organ and other similar tone notes are sustained even if the pedal is not pressed.
Sustains notes that are playing when the pedal is depressed before the keyboard keys are released.
Slightly softens notes played while the pedal is depressed.
Pressing the pedal starts and stops Auto Accompaniment or song playback.
E-10
Controlling the Keyboard Sounds
Changing the Pitch (Transpose, Tuning)
Changing the Pitch in Semitone Steps (Transpose)
The transpose feature lets you change the pitch, in semitone steps. A simple operation lets you instantly change the pitch to match that of a singer.
• The transpose setting range is –12 to +12 semitones.
1.
Press 3.
Trans.
2.
Use the bn (10-key) [–] and [+] keys to select the transpose setting you want.
Fine Tuning (Tuning)
Use the tuning feature when you need to adjust the pitch slightly to play along with another musical instrument. Also, some artists perform their music with slightly altered tuning. You can use the tuning feature to adjust tuning so it exactly matches a performance on a CD.
• The tuning setting range is –99 to +99 cents.
1.
Press 3 a number of times until “Tune” appears on the display (page E-4).
Sampling a Sound and Playing It on the Keyboard (Sampling)
You can use the Digital Keyboard to sample a sound from a portable audio player, or other device, and then play the sound with the keyboard keys or voice pads. For example, you could sample the bark of your dog and then use the sound in a melody. You also can sample and use passages from a CD. The sampling feature is a great way to create new sounds that are highly creative.
Connection
Connect a external device.
Keyboard AUDIO IN jack
CD player, Cassette player, etc.
Stereo mini plug
• Connection requires commercially available connecting cords, supplied by you. The connecting cords should have a stereo mini plug on one end and a plug that matches the configuration of the external device on the other end.
• Turn off the external device and the Digital Keyboard before connecting them.
• Sampled sounds are recorded in monaural.
Sampling a Sound and Playing It
There are two sampling methods: full sampling and short sampling.
English
Tune
2.
Use the bn (10-key) [–] and [+] keys to adjust the tuning.
Full Sampling
This method allows sampling of a single sound with a duration of one second.
1.
Turn the volume levels of the external device and Digital Keyboard down.
2.
Turn on the external device and then the Digital Keyboard.
3.
Press 4 and immediately release it.
This enters record standby.
Flashes
W
a i t i n
g
E-11
Controlling the Keyboard Sounds
4.
Output the sound from the external device.
The Digital Keyboard will start sampling automatically, and stop after one second. What you sample is stored as tone number 401.
Flashes
2.
While holding down 4, press the voice pad (br,
, or bt) that corresponds to the tone number
bs
where you want to store the sound.
• The relationship between tone numbers and voice pads is shown below.
S a m p l i n g
Lights
O r i g i n a l
5.
Try playing something on the keyboard.
• You can press pad 4 or 5 (ck or cl) to sound the sampled sound (page E-7).
• Sampling will not start if the volume level of the external device is too low.
• A new sample replaces sample data currently assigned to tone number 401. All of the old data (including short sampled sounds) is deleted.
Short Sampling
With short sampling, you can sample up to three sounds, each one with a duration of approximately 0.3 seconds. You can sound the short sampled sounds using voice pads 1 through 3.
Selected Tone
Number
Pressed Voice Pad Pad 1 (
Example: When voice pad 3 (Tone Number 404) is
selected
402 403 404
) Pad 2 (bs) Pad 3 (bt)
br
Flashes
V o i . P a d 3
Record standby is entered when you release
Flashes
W
a i t i n
3.
Output the sound from the external device.
Sampling starts automatically and stops after about 0.3 seconds.
Lights
g
4
.
1.
Connect an external device to the keyboard.
Refer to steps 1 through 2 under “Full Sampling” (page E-11).
E-12
V o i . P a d 3
4.
Try playing something on the keyboard.
• You also can sound the sampled sound by pressing the voice pad you pressed in step 2.
• Sampling will not start if the volume level of the external device is too low.
• Sampling a new sound deletes the sound assigned to the same tone number and the full sampling sound (page E-11).
Loading...
+ 32 hidden pages