Canon FS36, FS306, FS37 User Manual

Instruction Manual

COPY

PUB. DIE-0349-000

Digital Video Camcorder

Introduction

COPY

Important Usage Instructions

WARNING!

CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK AND TO REDUCE ANNOYING INTERFERENCE, USE THE RECOMMENDED ACCESSORIES ONLY.

CAUTION:

DISCONNECT THE MAINS PLUG FROM THE SUPPLY SOCKET WHEN NOT IN USE.

WARNING:

To r edu ce the risk of electric shock, do not expose this product to dripping or splashing.

The Mains plug is used as the disconnect device. The Mains plug shall remain readily operable to disconnect the plug in case of an accident.

While using the compact power adapter, do not wrap it or cover it with a piece of cloth, and do not place it in confined narrow spaces. Heat may build up, the plastic case may deform and it could result in electric shock or fire.

CA-570 identification plate is located on the bottom.

European Union (and EEA) only.

Improper handling of this type of waste could have a possible impact on the environment and human health due to potentially hazardous substances that are generally associated with EEE. Your cooperation in the correct disposal of this product will contribute to the effective usage of natural resources. For more information about the recycling of this product, please contact your local city office, waste authority, approved scheme or your household waste disposal service or visit www.canon-europe.com/environment. (EEA: Norway, Iceland and Liechtenstein)

TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.

TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS PRODUCT TO RAIN OR MOISTURE.

Using any device other than the Compact Power Adapter CA-570 may damage the camcorder.

These symbols indicate that this product is not to be disposed of with your household waste, according to the WEEE Directive (2002/96/EC), the Battery Directive (2006/66/EC) and/or your national laws implementing those Directives. This product should be handed over to a designated collection point, e.g., on an authorized one-for-one basis when you buy a new similar product or to an authorized collection site for recycling waste electrical and electronic equipment (EEE) and batteries and accumulators.

Getting to Know the Camcorder

COPY

What is so special about recording on flash memory?

Your videos and photos are recorded in the built-in memory ( / only) or on a memory card (SD or SDHC card). Recording on flash memory means that there are no moving parts in the recorder unit of the camcorder. To you, it means a camcorder that is smaller, lighter and faster.

Other features of this camcorder

Whether you are using a camcorder for the first time or are very experienced, this camcorder offers many easy-to-use functions. The following are just but a few examples of the many functions that can enrich your shooting experience.

• Dual Shot ( 21): With Dual Shot ( mode), recording is as simple as pressing a single button and using the zoom lever. The camcorder will take care of the rest!

• Image Stabilization ( 79): Dynamic IS compensates for camcorder shake when shooting video while walking. This gives you more freedom and mobility when recording movies.

• Special Scene recording programs ( 40): When recording in a variety of situations, such as at the beach, the camcorder automatically selects the optimal settings for that situation.

• Pre-recording function ( 45): The camcorder records for 3 seconds before you start shooting, ensuring that those once-in-a-lifetime moments do not slip by.

• Video Snapshot ( 43): Create a montage of scenes and even set it to music when you play it back.

Table of contents

COPY

Introduction ______________________________

3 Getting to Know the Camcorder 8 About this Manual

10 Overview

10 Supplied Accessories and CD-ROMs 11 Components Guide 13 Screen Displays

Preparations _____________________________

16 Getting Started

16 Charging the Battery Pack 18 Preparing the Accessories 19 Adjusting the Position and Brightness of the LCD Screen

21 Basic Operation of the Camcorder

21 Operating Modes 22 Joystick and Joystick Guide 23 Using the Menus

25 First Time Settings

25 Setting the Date and Time 25 Changing the Language 26 Changing the Time Zone

27 Using a Memory Card

27 Memory Cards Compatible for Use with the Camcorder 27 Inserting and Removing a Memory Card 28 28 Initializing the Built-In Memory (

Card

/ Selecting the Memory for the Recordings

/ only) or Memory

Table of contents

COPY

Video ____________________________________

30 Basic Recording

30 Shooting Video 31 Selecting the Video Quality

31 Zooming: Optical, Advanced and Digital Zoom 33 Quick Start Function

34 Basic Playback

34 Playing Back the Video 35 Selecting What Recordings to Play Back 36 Selecting Scenes by Recording Date 37 Selecting the Playback Starting Point from the Movie Timeline 38 Pre-selecting Recordings from the Index Screen 39 Deleting Scenes

40 Advanced Functions

40 Special Scene Recording Programs 41 Controlling Shutter Speed and Other Functions while Shooting 43 Mini Video Light 43 Video Snapshot 45 Pre-recording Function 46 Self Timer 46 Automatic Backlight Correction and Manual Exposure

47 Manual Focus Adjustment 48 White Balance 49 Image Effects 49 Digital Effects 50 On-Screen Displays and Data Code

51 Playlist and Scene Operations

51 Dividing Scenes 52 Editing the Playlist: Adding, Deleting and Moving Playlist

(Recording Mode)

Adjustment

Scenes

/ Copying Scenes

Photos __________________________________

COPY

55 Basic Recording

55 Taking Photos 55 Selecting Photo Size and Quality 56 Erasing a Photo Right After Recording It

57 Basic Playback

57 Viewing Photos 59 Magnifying Photos during Playback 59 Deleting Photos

61 Additional Functions

61 Histogram Display 61 Protecting Photos 62 63 Other Functions You Can Use When Taking Photos

63 Printing Photos

63 Printing Photos 64 Selecting the Print Settings 66 Print Orders

/ Copying Photos

External Connections _______________________

69 Terminals on the Camcorder

69 Connection Diagrams

70 Playback on a TV Screen

71 Saving Your Recordings

71 Saving Your Recordings on a Computer 71 Authoring DVD Discs and Photo DVDs 74 Transfer Orders 74 Copying your Recordings to an External Video Recorder 75 Transferring Photos to a Computer

Table of contents

COPY

Additional Information ______________________

77 Appendix: Menu Options Lists

77 FUNC. Menu 79 Setup Menus

85 Trouble?

85 Troubleshooting 89 List of Messages

97 Do’s and Don’ts

97 Handling Precautions 100 Maintenance/Others 100 Using the Camcorder Abroad 101 Music Files

102 General Information

102 System Diagram 103 Optional Accessories 105 Specifications 108 Index

Introduction

COPY

About this Manual

Thank you for purchasing the Canon LEGRIA FS37/FS36/FS307/FS306/FS305*. Please read this manual carefully before you use the camcorder and retain it for future reference. Should your camcorder fail to operate correctly, refer to Troubleshooting ( 85).

* Availability differs from area to area.

Conventions Used in this Manual

• IMPORTANT: Precautions related to the camcorder’s operation.

• NOTES: Additional topics that complement the basic operating procedures.

• POINTS TO CHECK: Restrictions or requirements regarding the function described.

• : Reference page number in this manual.

To complete some operations, you will need to refer also to the instruction manual of the optional DW-100 DVD Burner. This will be indicated with the

• : Text that applies only to the model shown in the icon.

• The following terms are used in this manual:

When not specified as “memory card” or “built-in memory”, the term “memory” by itself refers to both ( “Scene” refers to one movie unit from the point you press the button to start recording until you press again to pause the recording.

• The photos included in this manual are simulated pictures taken with a still camera. Unless indicated otherwise, illustrations and menu icons refer to the .

icon and the name of the relevant chapter or section.

/ only).

Start/Stop

Names of buttons and switches other

COPY

than the joystick are indicated within a “button” frame. For example .

FUNC.

Special Scene Recording Programs

Recording in a very bright ski resort or capturing the full colors of a sunset or a fireworks display becomes as easy as selecting a Special Scene recording program. For details about the available options, refer to the following sidebar.

Brackets [ ] are used to refer to menu options as they are displayed on screen. In tables in this manual the default value is shown in boldface. For example [ON], [OFF].

FUNC.

[PROGRAM AE] [ PORTRAIT] Press to display the Special Scene (SCN) recording programs Desired recording program

FUNC.

In this manual, the arrow is used to abbreviate menu selections. For a detailed explanation refer to Using the Menus ( 23).

( 25)

Introduction

COPY

Overview

Supplied Accessories and CD-ROMs

The following accessories are supplied with the camcorder.

CA-570 Compact Power Adapter (incl. power cord)

Quick Guide

The following CD-ROMs and software are supplied with the camcorder.

• PIXELA Application - Disc 1 CD-ROM* and ‘PIXELA Applications Installation Guide’

- ImageMixer 3 SE Transfer Utility - For saving and transferring movies.

- Music Transfer Utility - For transferring to a memory card music files that can be used during playback on the camcorder.

• PIXELA Application - Disc 2 CD-ROM*

- ImageMixer 3 SE Video Tools - For managing, editing, and playing back movies.

• Instruction Manual/Music Data Disc CD-ROM - Contains the full-length camcorder instruction manual (electronic version on PDF file) and music files that can be used as background music during playback. This CD-ROM cannot be played back on a CD player. The music files on this CD-ROM are for exclusive use with the supplied PIXELA applications, Music Transfer Utility and ImageMixer 3 SE Video Tools. For more details, refer to the ‘Music Transfer Utility Software Guide’ and ‘ImageMixer 3 SE Software Guide’ on the PIXELA Application - Disc 1 CD-ROM.

BP-808 Battery Pack STV-250N

Stereo Video Cable

Yellow • Red • White plugs

IFC-300PCU USB Cable

* The CD-ROM includes the instruction manual of the software (electronic version on PDF file).

Components Guide

COPY

Left side view

Right side view

Front view

RESET button ( 88) VIDEO SNAP (Video Snapshot) button

( 43)/ (print/share) button ( 64)

DISP. (on-screen display) button ( 50, 61)/ BATT. INFO button ( 15)

USB terminal ( 69) AV OUT te rminal ( 69) Speaker ( 34) Strap mount ( 18) ACCESS (memory access) indicator

( 30, 55) Grip belt DC IN terminal ( 16) Mini video light ( 43) Stereo microphone

Introduction

COPY

Back view

Top vie w

Bottom view

LCD screen ( 19) ON/OFF(CHG) (power/charge) indicator

( 17) Camera mode dial ( 21) Start/Stop button ( 30)

(camera/play) button ( 22)

PLAYLIST button ( 51)/ Zoom in T (telephoto) button ( 31)

(stop) button ( 34)/

Zoom out W (wide-angle) button ( 31)

/ (play/pause) button ( 34)/

START/STOP button ( 30) FUNC. button ( 23, 77) Joystick ( 22) PHOTO button ( 55) Zoom lever ( 31) POWER button Tripod socket ( 97) Battery release latch ( 17) Memory card slot ( 27) Battery compartment ( 16) Battery compartment cover/

Memory card slot cover Serial number

The serial number label is located on the top surface of the battery compartment cover.

Screen Displays

COPY

Recording Movies

Playing Movies (During Playback)

Operating mode ( 21) Recording program ( 40, 41) White balance ( 48) Image effects ( 49) Digital effects ( 49) Recording mode ( 31) Manual focus ( 47) Image stabilizer ( 79) Pre-recording function ( 45) Memory operation ( 15) Number of scenes recorded (record

pause)/Time code (hours : minutes : seconds, while recording)

Remaining recording time

On the memory card

/ In the built-in memory

Remaining battery time ( 15) Wind screen off ( 79) Backlight correction ( 46) Joystick guide ( 22) Mini video light ( 43) Level marker ( 81) Audio level indicator ( 81) Time code/Playback time

(hours : minutes : seconds) Scene number Data code ( 81)

Introduction

COPY

Recording Photos

Viewing Photos

Zoom ( 31), Exposure ( 46) Recording program ( 40, 41) White balance ( 48) Image effect ( 49) Digital effect ( 49) Photo quality/size ( 55) Manual focus ( 47) Remaining battery time ( 15) Number of photos available ( 15)

On the memory card

/ In the built-in memory

Self timer ( 46) AF frame ( 80) Joystick guide ( 22) Mini video light ( 43) Focus and exposure lock ( 55) Camcorder shake warning ( 80) Photo number ( 15, 84) Current photo / Total number of photos Histogram ( 61) Date and time of recording Photo protection mark ( 61) Manual exposure ( 46) Photo size ( 55) File size Aperture value Shutter speed ( 41)

Memory operation

COPY

Record, Record pause,

Playback, Playback pause,

Fast playback,

Fast reverse playback, Slow playback, Slow reverse playback

Remaining recording time

When there is no more free space on the memory, [ END] (built-in memory, / only) or [ END] (memory card) will be displayed and the recording will stop.

, Remaining battery time

• The icon shows a rough estimate of the remaining charge as a percentage of the full charge of the battery pack. The remaining recording/playback time of the battery pack is displayed, in minutes, next to the icon.

• When is displayed in red, replace the battery pack with a fully charged one.

• When you attach an empty battery pack, the power may turn off without displaying .

• The first time you use a battery pack, fully charge it and then use the camcorder until the battery pack is completely exhausted. Doing so will ensure that the remaining recording time will be displayed accurately.

• Depending on the conditions under which the camcorder and the battery pack are used, the actual battery charge may not be indicated accurately.

• When the camcorder is off, press to display the charge status of a battery pack. The Intelligent System will display the charge status (as a percentage) and the remaining recording time (in minutes) for 5 seconds. If the battery pack is exhausted, the battery information may not be displayed.

Number of photos available

in red: No card in green: 6 or more photos in yellow: 1 to 5 photos in red: No more photos can be recorded

• When viewing the photos, the display will always be in green.

• Depending on the recording conditions, the number of available photos displayed may not decrease even after a recording has been made, or may decrease by 2 photos at once.

Photo number

The photo number indicates the name and location of the file on the memory card. For example, the file name of photo 101-0107 is “IMG_0107.JPG”, stored under the folder “DCIM\101CANON”.

BATT.INFO

Preparations

COPY

This chapter describes basic operations, such as navigating the menus, and first time settings to help you learn more about your camcorder.

Getting Started

Charging the Battery Pack

The camcorder can be powered with a battery pack or directly using the compact power adapter. Charge the battery pack before use. For approximate charging times and recording/playback times with a full battery pack, refer to the tables on pages 103-104.

DC IN terminal

2 Plug the power cord into a power

outlet.

3 Connect the compact power

adapter to the camcorder’s DC IN terminal.

4 Slide the battery compartment

cover away from the lens and open it.

5 Insert the battery pack all the way

into the compartment and press gently until it clicks.

6 Close the cover and slide it toward

the lens until you hear a click.

1 Connect the power cord to the

compact power adapter.

ON/OFF(CHG) indicator

COPY

TO REMOVE THE BATTERY PACK

7 Charging will start when the

camcorder is turned off.

• The ON/OFF(CHG) indicator starts flashing in red. The indicator will go out when the charging is completed.

• If the indicator flashes quickly, refer to Troubleshooting ( 85).

ONCE THE BATTERY PACK IS FULLY CHARGED

1 Disconnect the compact power

adapter from the camcorder.

2 Unplug the power cord from the

power outlet and the compact power adapter.

Battery release latch

1 Slide the battery compartment

cover away from the lens and open it.

2 Press the battery release latch and

pull out the battery pack.

3 Close the cover and slide it toward

the lens until you hear a click.

IMPORTANT

• Turn off the camcorder before connecting or disconnecting the compact power adapter. After turning off the camcorder, important data is updated in the memory. Be sure to wait until the ON/OFF(CHG) indicator turns off.

• We recommend charging the battery pack in temperatures between 10 °C and 30 °C. Outside the temperature range of 0 °C to 40 °C, the charging will not start.

• Do not connect to the camcorder’s DC IN terminal or to the compact power adapter any electrical equipment that is not expressly recommended for use with this camcorder.

• To prevent equipment breakdowns and excessive heating, do not connect the

Preparations

COPY

supplied compact power adapter to voltage converters for overseas travels or special power sources such as those on aircraft and ships, DC-AC inverters, etc.

NOTES

• Turn off the camcorder before charging the battery pack. The battery pack will not charge while the camcorder is on.

• If remaining battery time is an issue, you can power the camcorder using the compact power adapter so the battery pack will not be consumed.

• Charged battery packs continue to discharge naturally. Therefore, charge them on the day of use, or the day before, to ensure a full charge.

• We recommend that you prepare battery packs to last 2 to 3 times longer than you think you might need.

Preparing the Accessories

finger, and the button with your thumb.

Start/Stop

TO REMOVE THE GRIP BELT

1 Lift the padded handgrip’s flap

and detach the strap from the Velcro pad.

2 Pull the strap to remove it first

from the front bracket on the camcorder, then to unthread it from the handgrip and finally to remove it from the rear bracket on the camcorder.

TO ATTACH A WRIST STRAP

Fasten the grip belt.

Adjust the grip belt so that you can reach the zoom lever with your index

Pass the attaching end of the wrist strap through the back bracket on the camcorder, thread the wrist strap through the loop and fasten.

You can also attach the wrist strap to

COPY

the strap mount on the grip belt to use both for extra convenience and protection.

TO ATTACH A SHOULDER STRAP

Pass the ends of the shoulder strap through the strap mount on the grip belt and adjust the length of the strap.

You can also remove the grip belt and attach the shoulder strap directly to the rear bracket on the camcorder.

Adjusting the Position and Brightness of the LCD Screen

Rotating the LCD Panel

Open the LCD panel 90 degrees.

• You can rotate the panel 90 degrees downward.

• You can rotate the panel 180 degrees toward the lens. Rotating the LCD panel 180 degrees can be useful when you wish to include yourself in the picture when recording with the self timer.

180°

90°

TO REATTACH THE GRIP BELT

1 Pass the end of the strap through

the rear bracket on the camcorder.

2 Thread the strap through the

padded handgrip and then pass it through the front bracket on the camcorder.

3 Fasten the grip belt as necessary,

attach the strap to the Velcro pad on the handgrip and close the flap.

180°

Subject can monitor the LCD screen

NOTES

About the LCD screen: The screen is

produced using extremely high-precision manufacturing techniques, with more than

99.99% of the pixels operating to

specification. Less than 0.01% of the pixels may occasionally misfire or appear as black, red, blue or green dots. This has

Preparations

COPY

no effect on the recorded image and does not constitute a malfunction.

LCD Backlight

You can set the brightness of the screen to dim, normal or bright. To set the screen to dim, turn on [LCD DIMMER] (s 81). To toggle between normal and bright or to turn off [LCD DIMMER], perform the following procedure.

While the camcorder is on, hold

DISP.

pressed down for more than

2 seconds.

Repeat the operation to switch between normal and bright.

NOTES

• This setting does not affect the brightness of the recording.

• Using the bright setting will shorten the effective usage time of the battery pack.

• When the compact power adapter is connected while the brightness of the screen is normal, the brightness will automatically change to bright.

Basic Operation of the

COPY

Camcorder

Operating Modes

The camcorder’s operating mode is determined by the button and the position of the camera mode dial. In this manual, indicates that a function is available in the operating mode shown and indicates that the function is not available. See the following table for a summary of the operating modes.

Recording: Dual Shot and Flexible Recording

The camcorder offers two basic modes for recording video or photos: Dual Shot ( mode) for beginners or if you just prefer not to bother with detailed camcorder settings, and flexible recording mode, which lets

you change the camcorder’s settings to your preference.

Turn the camera mode dial to to set the camcorder to mode. You do not need to worry about any settings and can shoot video using just

Start/Stop

or take photos using just

. You can also use the zoom

PHOTO

lever, Quick Start ( 33) and Video Snapshot ( 43). To set the camcorder to flexible recording mode, turn the camera mode dial to for movies or for photos. You can access the menus and change

Operating mode Icon display Operation

Recording movies or photos to the memory (Dual Shot) 21

(green)

(blue)

(green)

(blue)

Recording movies to the memory 30

Recording photos to the memory 55

Playing movies from the memory (press while the camera mode dial is set to or

Viewing photos from the memory (press while the camera mode dial is set to )

)

Preparations

COPY

settings to your preference. Even in flexible recording mode, the camcorder can help you with the settings. For example, you can use the Special Scene recording programs ( 40) to set at once all the optimal settings to match special recording conditions.

Playback

Press to switch between the recording mode indicated by the camera mode dial and playback mode (

/ the selected media will

remain the same). When the camera mode dial is set to or , pressing

switches the camcorder to movie playback mode. When the camera mode dial is set to , pressing

switches the camcorder to photo playback mode. Even if the camcorder is turned off, pressing will start the camcorder in the corresponding playback mode.

NOTES

In mode you cannot access the menus or joystick guide but you can change the following settings in advance, before setting the camcorder to mode.

- Recording mode of movies

- Size/quality of photos

- Widescreen

- Auto slow shutter

- All settings in the [ SYSTEM SETUP]

- LCD screen dimmer

-Demo mode

- Image stabilizer (If you select

[ DYNAMIC] in advance, [IMG STAB] will be set to [ DYNAMIC]; if you select [ STANDARD] or [ OFF] in

advance, [IMG STAB] will be set to [STANDARD].)

Joystick and Joystick Guide

Use the joystick to operate the camcorder’s menus.

Push the joystick up, down, left or right ( , ) to select an item or change settings.

Press the joystick itself ( ) to save the settings or confirm an action. On menu screens, this is indicated by the icon

( ).

OFF

A M

The functions that appear in the joystick guide depend on the operating mode. By default, the joystick guide is minimized. Push the joystick ( ) to display it. During or mode, select ( ) a function and press to change the setting. With some functions, you will need to make further adjustments (indicated by small arrows).

During playback mode, select ( ) a

COPY

“row” of functions and press to operate the function in the middle or push the joystick ( ) to operate the function on the left or right side of the row, respectively.

In either mode, if you wait a few seconds, the joystick guide will minimize again but the selected function can still be operated. You can also push the joystick ( ) to hide the joystick guide.

Using the Menus

Selecting a FUNC. Menu Option in Recording Mode

Many of the camcorder’s functions can be adjusted from the menus that open after pressing the FUNC. button

FUNC.

( ). To access the menus, set the camcorder to flexible recording mode. In mode, except for a few exceptions, most menu settings will return to their default values.

For details about the available menu options and settings, refer to the appendix Menu Options Lists ( 77).

1 Press .

FUNC.

2 Select ( ) the icon of the

function you want to change from the left side column.

Menu items not available will appear grayed out.

3 Select ( ) the desired setting

from the available options at the bottom bar.

• The selected option will be highlighted in orange.

• With some settings you will need to make further selections and/or press . Follow the additional operation guides that will appear on the screen (such as the icon, small arrows, etc.).

4 Press to save the settings

FUNC.

and close the menu.

You can press to close the menu at any time.

FUNC.

Preparations

COPY

Selecting an Option from the Setup Menus

1 Press .

FUNC.

2 Select ( , ) the icon and

press to open the setup menus.

You can also hold pressed down for more than 1 second to open directly the setup menus screen.

FUNC.

3 Select ( ) the desired menu from

the left side column and press .

The title of the selected menu appears on top of the screen and under it the list of settings.

4 Select ( ) the setting you want

to change and press .

• The orange selection bar indicates the menu setting currently selected. Items not available appear in black.

• Push the joystick ( ) to return to the menu selection screen (step 3).

5 Select ( ) the desired option and

press to save the setting.

6 Press .

FUNC.

You can press to close the menu at any time.

FUNC.

First Time Settings

COPY

Setting the Date and Time

You will need to set the date and time of the camcorder before you can start using it. The [DATE/TIME] screen will appear automatically when the camcorder’s clock is not set.

• The date appears in a year-month-day format only in the first setup screen. In subsequent screen displays the date and time will appear as day-month-year (for example, [1.JAN.2010 12:00 AM]). You can change the date format ( 84).

• You can also change the date and time later on (not during the initial setup). To open the [DATE/TIME] screen:

FUNC.

[ MENU] [ DATE/TIME SETUP] [DATE/TIME]

Changing the Language

When the [DATE/TIME] screen appears, the year will be displayed in orange and indicated with up/down arrows.

1 Change ( ) the year and move

( ) to the month.

2 Change the rest of the fields

(month, day, hour and minutes) in the same way.

3 Select ( ) [OK] and press to

start the clock and close the setup screen.

IMPORTANT

• When you do not use the camcorder for about 3 months, the built-in rechargeable lithium battery may discharge completely and the date and time setting may be lost. In such case, recharge the built-in lithium battery ( 99) and set the time zone, date and time again.

( 21)

Options

[][MELAYU][] [DEUTSCH][NEDERLANDS][ ] [][POLSKI][]



[ENGLISH]

[ESPAÑOL][ ] [ ] [FRANÇAIS][TÜRKÇE][] [ITALIANO][ ] [ ] [MAGYAR][ ]

FUNC.

[ MENU] [ DISPLAY SETUP] [LANGUAGE ] Desired language

FUNC.

[PORTUGUÊS][ ]



Default value

Preparations

COPY

NOTES

• If you changed the language by mistake, select the menu item with the mark and change the setting.

• The displays and that appear in some menu screens refer to the name of buttons on the camcorder and will not change, regardless of the language selected.

Changing the Time Zone

Change the time zone to match your location. The default setting is Paris.

( 21)

TO SET THE HOME TIME ZONE

FUNC.

[ MENU] [ DATE/TIME SETUP] [T.ZONE/DST] Your local time zone*

FUNC.

WHEN YOU TRAVEL

FUNC.

[ MENU] [ DATE/TIME SETUP] [T.ZONE/DST] Local time at your destination*

FUNC.

* To adjust for daylight saving time, select the

area name marked with a .

Using a Memory Card

COPY

Memory Cards Compatible for Use with the Camcorder

You can use commercially available

SDHC (SD high capacity) memory cards and SD memory cards with this camcorder to record movies and photos. However, depending on the memory card, you may not be able to record movies on it. Refer to the following table. As of October 2009, the movie recording function has been tested using SD/SDHC memory cards made by Panasonic, SanDisk and Toshiba.

NOTES

About the SD Speed Class: The SD Speed

Class is a standard that indicates the minimum guaranteed data transfer speed of SD/SDHC memory cards. When you buy a new memory card, look for the Speed Class logo on the package.

Inserting and Removing a Memory Card

Make sure to initialize all memory cards before using them with this camcorder ( 28).

1 Turn off the camcorder.

Make sure that the ON/OFF(CHG) (power/charge) indicator is off.

2 Slide the memory card slot cover

away from the lens and open it.

3 Insert the memory card straight,

with the label facing away from the lens, all the way into the memory card slot until it clicks.

Memory cards usable for recording movies

Memory card Capacity SD Speed Class Recording movies

64 MB or less – –

SD memory cards

SDHC memory cards 4 GB to 32 GB

* Depending on the memory card, it may not be possible to record movies.

128 MB to 2 GB – *

512 MB to 2 GB

, , ,

Preparations

COPY

4 Close the cover and slide it toward

the lens until you hear a click.

Do not force the cover closed if the memory card is not correctly inserted.

IMPORTANT

Memory cards have front and back sides that are not interchangeable. Inserting a memory card facing the wrong direction can cause a malfunction of the camcorder.

NOTES

To remove the memory card: Push the

memory card once to release it. When the memory card springs out, pull it all the way out.

/ Selecting the Memory for

the Recordings

You can select to record your movies and photos in the built-in memory or on the memory card. The built-in memory is the default media for recording both.

( 21)

FUNC.

[ MENU] [ MEMORY OPER.] [MEDIA:MOVIES] or [MEDIA:PHOTOS] The memory you want to use* Press

FUNC.

* For each media, you can check the total,

used, and approximate available space. The approximate available space will depend on the recording mode (for movies) or size/quality (for photos) currently in use.

Initializing the Built-In Memory ( /

only) or Memory Card

Initialize memory cards when you use them with this camcorder for the first time. You can also initialize a memory card or the built-in memory (

only) to permanently delete all the

data it contains.

/ At the time of purchase,

COPY

the built-in memory comes preinitialized.

Options

[INITIALIZE] Clears the file allocation table but does not

physically erase the stored data. [COMPL.INIT.] Erases all data completely.

FUNC.

[ MENU] [ MEMORY OPER.] [INITIALIZE] The memory you want to initialize Initialization method [YES]* [OK]

FUNC.

[ MENU] [ MEMORY OPER.] [INITIALIZE] Initialization method [YES]* [OK]

FUNC.

IMPORTANT

• Initializing the memory will permanently erase all data. Lost original recordings cannot be recovered. Make sure you

( 21)

save important recordings in advance using an external device ( 71).

• When the memory is initialized, music files will also be erased.

- Windows users: Use the supplied

software Music Transfer Utility to transfer the music files on the supplied Instruction Manual/Music Data Disc CD-ROM to a memory card. For details, refer to the software’s instruction manual (PDF file).

- Mac OS users: Use the Finder to

transfer the music files on the supplied Instruction Manual/Music Data Disc CD-ROM to a memory card. Refer to Music Files ( 101) for the folder structure of the memory and CDROM.

• While the initialization is in progress, do not disconnect the power source or turn off the camcorder. In addition, do not perform any operation on the camcorder (except canceling initialization, if necessary).

* Press to cancel the complete

initialization while it is in progress. All recordings will be erased but the recording media can be used without any problem.

Video

COPY

This chapter covers functions related to shooting movies, including recording, playback, and memory operations.

Basic Recording

Shooting Video

( 21)

1 Set the camera mode dial to or

2 Turn on the camcorder.

/ You can select the

memory to be used for recording movies ( 28).

3 Press to begin

Start/Stop

recording.

• Recording starts; press again to pause the recording.

Start/Stop

• You can also press on the LCD panel.

START/STOP

WHEN YOU HAVE FINISHED RECORDING

1 Make sure that the ACCESS

indicator is off. 2 Turn off the camcorder. 3 Close the LCD panel.

IMPORTANT

Observe the following precautions while the ACCESS indicator is on or flashing. Failing to do so may result in permanent data loss or damage to the memory.

- Do not open the memory card slot cover.

- Do not disconnect the power source or

turn off the camcorder.

- Do not change the operating mode.

NOTES

• About the Power Save mode: To save p ower

when the camcorder is powered by a battery pack, the camcorder will automatically shut off if left without any operations for 5 minutes ( 83). Press

• When recording in bright places it may

to turn on the camcorder.

be difficult to use the LCD screen. Conversely, when recording in dark places, the LCD panel may be a nuisance to others nearby. In such cases, change the brightness of the LCD screen accordingly ( 19, 82).

+ 81 hidden pages