Canon EOS 760D, EOS REBEL T6s Basic Manual

Camera

Wi-Fi/NFC Function

This manual is the Basic Instruction Manual. For more detailed instructions, refer to the Instruction Manuals included in the Camera Instruction Manual CD-ROM.

Basic Instruction Manual

EOS REBEL T6S (W)

EOS 760D (W)

The Camera Basic Instruction Manual covers the most basic operations.

Camera Basic Instruction Manual

EOS REBEL T6S (W)

EOS 760D (W)

Introduction

The EOS REBEL T6S or EOS 760D is a digital single-lens reflex camera featuring a fine-detail CMOS sensor with approx. 24.2 effective megapixels, DIGIC 6, high-precision and high-speed 19-point AF (cross-type AF point: max. 19 points), approx. 5.0 fps continuous shooting, Live View shooting, Full High-Definition (Full HD) movie shooting, and Wi-Fi/NFC function.

Before Starting to Shoot, Be Sure to Read the Following

To avoid botched pictures and accidents, first read the “Safety Precautions” (p.16-18) and “Handling Precautions” (p.19-21).

Refer to This Manual while Using the Camera to Further Familiarize Yourself with the Camera

While reading this manual, take a few test shots and see how they come out. You can then better understand the camera.

Testing the Camera Before Use and Liability

After shooting, play images back and check whether they have been properly recorded. If the camera or memory card is faulty and the images cannot be recorded or downloaded to a computer, Canon cannot be held liable for any loss or inconvenience caused.

Copyrights

Copyright laws in your country may prohibit the use of your recorded images or copyrighted music and images with music in the memory card for anything other than private enjoyment. Also be aware that certain public performances, exhibitions, etc., may prohibit photography even for private enjoyment.

Item Check List

Battery Pack

LP-E17

(with protective cover)

Battery Charger

LC-E17/LC-E17E*

Wide Strap

Camera

(with eyecup and body cap)

Interface Cable

Before starting, check that all the following items are included with your camera. If anything is missing, contact your dealer.

* Battery Charger LC-E17 or LC-E17E is provided. (The LC-E17E comes with a

power cord.)

 The Instruction Manuals and CD-ROMs provided are listed on the next page.  If you purchased a Lens Kit, check that the lenses are included.  Depending on the Lens Kit type, lens instruction manuals may also be

included.

 Be careful not to lose any of the above items.

Instruction Manual and CD-ROMs

Camera and Wi-Fi/NFC Function

Basic Instruction Manual

(This Manual)

The instruction manual consists of a booklet and electronic manuals (PDF files on the CD-ROM). The booklet is the Basic Instruction

Manual. For more detailed instructions, see the Camera Instruction Manual on the CD-ROM.

Camera Instruction Manual CD-ROM

Contains the following manuals (PDF files):

• Camera Instruction Manual

• Wi-Fi/NFC Function Instruction Manual

• Quick Reference Guide Instructions for viewing the Camera Instruction Manual CD-ROM are on pages 162-163.

EOS DIGITAL Solution Disk (Software CD-ROM) Contains software such as image-editing software and Software Instruction Manuals (PDF files). For more information and installation procedures of the software, see pages 166-167. Instructions for viewing the Software Instruction Manual are on page 168.

Compatible Cards

In this manual, “card” refers to SD memory cards, SDHC memory cards, and SDXC memory cards. * The camera does not come with a card for recording images/

movies. Please purchase it separately.

The camera can use the following cards regardless of capacity: If the

card is new or was previously formatted by another camera or computer, format the card with this camera (p.61).

• SD memory cards

• SDHC memory cards*

• SDXC memory cards*

* UHS-I cards supported.

Cards that Can Record Movies

When shooting movies, use a large-capacity SD card rated SD Speed Class 6 “ ” or higher.

 If you use a slow-writing card when shooting movies, the movie may

not be recorded properly. Also, if you play back a movie on a card with a slow reading speed, the movie may not play back properly.

 If you want to shoot still photos while shooting a movie, you will need

an even faster card.

 To check the card’s reading/writing speed, refer to the card

manufacturer’s Web site.

Quick Start Guide

White index Red index

Insert the battery (p.34).

To charge the battery, see page 32.

Insert the card (p.35).

With the card’s label facing

toward the back of the camera, insert it into the card slot.

Attach the lens (p.43).

Align the lens’s white or red mount

index with the camera’s mount index of the same color.

Set the lens focus mode switch to <f> (p.43).

Set the power switch to <1>, then set the Mode Dial to <A> (Scene Intelligent Auto)



Turn the Mode Dial while holding down

the lock release button at the center.

All the necessary camera settings

will be set automatically.

(p.70).

Quick Start Guide

Flip out the LCD monitor (p.37).

 To shoot while looking at the LCD monitor, see “Live View

Shooting” (p.131).

 To view the images captured so far, see “Image Playback” (p.94).  To delete an image, see “Erasing Images” (p.160).

When the LCD monitor displays the

date/time/zone setting screens, see page 40.

Focus on the subject (p.48).

Look through the viewfinder and

aim the viewfinder center over the subject.

Press the shutter button halfway,

and the camera will focus on the subject.

If necessary, the built-in flash will be

raised.

Take the picture (p.48).

Press the shutter button completely

to take the picture.

Review the picture.

The captured image will be

displayed for 2 sec. on the LCD monitor.

To display the image again, press

the <x> button (p.94).

Conventions Used in this Manual

Icons in this Manual

<6> : Indicates the Main Dial. <5> : Indicates the Quick Control Dial. <W><X><Y><Z> : Indicates the direction of the shift or move

<0> : Indicates the Setting button. 0, 9, 7, 8 : Indicates that each function remains active

* In this manual, the icons and markings indicating the camera’s buttons, dials,

and settings correspond to the icons and markings on the camera and on the LCD monitor.

3 : Indicates a function that can be changed by pressing the

<M> button to change its settings.

J :

(p.**) : Reference page numbers for more information.

When shown on the upper right of a page, it indicates that the function is available only in the Creative Zone modes (p.27).

: Warning to prevent shooting problems. : Supplemental information. : Tips or advice for better shooting. : Troubleshooting advice.

Basic Assumptions

All operations explained in this manual assume that the power switch

is set to <1> and the <R> switch is set to the left (Multi function lock released) (p.51).

It is assumed that all the menu settings, Custom Functions, etc. are

set to their defaults.

The illustrations in this manual show the camera attached with the

EF-S18-135mm f/3.5-5.6 IS STM lens as an example.

when the key on the Quick Control Dial is pressed.

for 4 sec., 6 sec., 10 sec., or 16 sec. after you let go of the button.

Chapters

234

678

Introduction

Getting Started

Basic Shooting and Image Playback

Setting the AF and Drive Modes

Image Settings

Advanced Operations

Shooting with the LCD Monitor (Live View Shooting)

Shooting Movies

Image Playback

Viewing the CD-ROM Instruction Manuals / Downloading Images to Your Computer

109

121

131

145

153

161

Contents

Introduction 4

Item Check List.................................................................................5

Instruction Manual and CD-ROMs................................................... 6

Compatible Cards.............................................................................7

Quick Start Guide ............................................................................. 8

Conventions Used in this Manual...................................................10

Chapters..........................................................................................11

Contents.........................................................................................12

Safety Precautions......................................................................... 16

Handling Precautions..................................................................... 19

Nomenclature................................................................................. 22

Getting Started 31

Charging the Battery ...................................................................... 32

Installing and Removing the Battery...............................................34

Installing and Removing the Card ..................................................35

Using the LCD Monitor................................................................... 37

Turning on the Power..................................................................... 38

Setting the Date, Time, and Zone................................................... 40

Selecting the Interface Language...................................................42

Attaching and Detaching a Lens..................................................... 43

Lens Image Stabilizer..................................................................... 46

Basic Operation.............................................................................. 47

Q Quick Control for Shooting Functions.......................................53

3 Menu Operations.................................................................. 55

d Using the Touch Screen....................................................... ...... 58

Formatting the Card ....................................................................... 61

Switching the LCD Monitor Display................................................ 63

lDisplaying the Grid...................................................................65

Q Displaying the Electronic Level...............................................66

Feature Guide ............................................................ .... ... ............. 68

Basic Shooting and Image Playback 69

A Fully Automatic Shooting (Scene Intelligent Auto)...................70

A Full Auto Techniques (Scene Intelligent Auto)..........................73

7 Disabling Flash.........................................................................75

C Creative Auto Shooting.............................................................76

2 Shooting Portraits......................................................................80

3 Shooting Landscapes...............................................................81

4 Shooting Close-ups..................... ... .... ........................................82

5 Shooting Moving Subjects........................................................83

8: Special Scene Mode .............................................................84

C Shooting Children......................................................................85

P Shooting Food............................................................................86

x Shooting Candlelight Portraits ...................................................87

6 Shooting Night Portraits (With a Tripod)....................................88

F Shooting Night Scenes (Handheld)............................................89

G Shooting Backlit Scenes............................................................90

Q Quick Control.......................... .... ... ............................................92

x Image Playback........................................................................94

Setting the AF and Drive Modes 97

f: Changing the Autofocus Operation (AF operation)..................98

S Selecting the AF Area and AF Point.......................................101

AF Area Selection Modes.............................................................104

MF: Manual Focus........................................................................105

i Selecting the Drive Mode........................................................106

j Using the Self-timer.................................................................107

Contents

Image Settings 109

Setting the Image-Recording Quality............................................110

g: Changing the ISO Speed to Suit the Light............................112

A Selecting a Picture Sty le.......................................................113

B: Matching the Light Source (White balance)..........................114

Auto Correction of Brightness and Contrast (Auto Lighting Optimizer)

Setting Noise Reduction................................................................116

Correction of Lens Peripheral Illumination and Aberrations..........118

Reducing Flicker...........................................................................120

Advanced Operations 121

d: Program AE................................................... .... ..................... 122

s: Conveying the Subject’s Movement (Shutter priority AE)..... 123

f: Changing the Depth of Field (Aperture priority AE) ............. 124

a: Manual Exposure................................................................... 125

q Changing the Metering Mode (Metering mode)...................... 126

Setting Exposure Compensation (Exposure comp.) .................... 127

Auto Exposure Bracketing (AEB) .................................................128

A Locking the Exposure (AE Lock)............................................. 129

D Using the Built-in Flash.............................................................130

Shooting with the LCD Monitor (Live View Shooting)

A Shooting with the LCD Monitor.............................................. 132

Changing the Autofocus Operation (AF operation)...................... 135

Using AF to Focus (AF Method)...................................................137

x Shooting with the Touch Shutter.............................................141

MF: Focusing Manually................................................................142

...115

131

Shooting Movies 145

Certification Logo

Select [54: Certification Logo Display] and press <0> to display some of the logos of the camera’s certifications. Other certifi ca tion logos can be found in this Instruction Manual, on the camera body, and on the camera’s package.

k Shooting Movies.....................................................................146

Autoexposure Shooting..............................................................146

Manual Exposure Shooting........................................................147

Setting the Movie Recording Size.................................................150

Image Playback 153

x Searching for Images Quickly.................................................154

u/y Magnified View ............................................... ... .... .............155

d Playing Back with the Touch Screen.........................................156

k Playing Back Movies...............................................................158

L Erasing Images.................................................... ....................160

Viewing the CD-ROM Instruction Manuals /

Downloading Images to Your Computer 161

Viewing the Camera Instruction Manual CD-ROM........................162

Downloading Images to a Computer.............................................164

Software Overview........................................................................166

Installing the Software...................................................................167

Software Instruction Manual.........................................................168

Contents

Safety Precautions

The following precautions are provided to prevent harm or injury to yourself and others. Make sure to thoroughly understand and follow these precautions before using the product.

If you experience any malfunctions, problems, or damage to the product, contact the nearest Canon Service Center or the dealer from whom you purchased the product.

Warnings

 To prevent fire, excessive heat, chemical leakage, explosions, and electrical shock,

follow the safeguards below:

• Do not use any batteries, power sources, or accessories not specified in the Instruction Manual. Do not use any home-made or modified batteries.

• Do not short-circuit, disassemble, or modify the battery. Do not apply heat or solder to the battery. Do not expose the battery to fire or water. Do not subject the battery to strong physical shock.

• Do not insert the battery’s plus and minus ends incorrectly.

• Do not recharge the battery in temperatures outside the allowable ambient temperature range. Also, do not exceed the recharging time indicated in the Instruction Manual.

• Do not insert any foreign metallic objects into the electrical contacts of the camera, accessories, connecting cables, etc.

 When disposing of a battery, insulate the electrical contacts with tape to prevent

contact with other metallic objects or batteries. This is to prevent a fire or an explosion.

 If excessive heat, smoke, or fumes are emitted when recharging the battery,

immediately unplug the battery charger from the power outlet to stop recharging. Otherwise, it may cause a fire, heat damage, or electrical shock.

 If the battery leaks, changes color, deforms, or emits smoke or fumes, remove it

immediately. Be careful not to get burned in the process. It may cause a fire, electrical shock or skin burn if you keep using it.

 Prevent any battery leakage from contacting your eyes, skin, and clothing. It can

cause blindness or skin problems. If the battery leakage contacts your eyes, skin, or clothing, flush the affected area with lots of clean water without rubbing it. See a physician immediately.

 Do not leave any cords near a heat source. It can deform the cord or melt the

insulation and cause a fire or electrical shock.

 Do not hold the camera in the same position for long periods of time. Even if the

camera does not feel too hot, prolonged contact with the same body part may cause skin redness, blistering or low-temperature contact burns. Using a tripod is recommended for people with circulation problems or very sensitive skin, or when using the camera in very hot places.

 Do not fire the flash at anyone driving a car or other vehicle. It may cause an

accident.

Follow the warnings below. Otherwise, death or serious injuries may result.

Safety Precautions

 Do not fire the flash near a person’s eyes. It may impair the person’s vision. When

using flash to photograph an infant, keep at least 1 meter/3.3 feet away.

 When the camera or accessories are not in use, make sure to remove the battery and

disconnect the power plug from the equipment before storing. This is to prevent electrical shock, excessive heat, fire, or corrosion.



Do not use the equipment where there is flammable gas. This is to prevent an explosion or a fire.

 If you drop the equipment and the casing breaks open to expose the internal parts, do

not touch the internal parts. There is a possibility of an electrical shock.

 Do not disassemble or modify the equipment. High-voltage internal parts can cause

electrical shock.

 Do not look at the sun or an extremely bright light source through the camera or lens.

Doing so may damage your vision.



Keep equipment out of the reach of children and infants, including when in use. Straps or cords may accidentally cause choking, electrical shock, or injury. Choking or injury may also occur if a child or infant accidentally swallows a camera part or accessory. If a child or infant swallows a part or accessor y, consult a physician immediately.

 Do not use or store the equipment in dusty or humid places. Likewise, store the

battery with its protective cover attached to prevent short-circuit. This is to prevent a fire, excessive heat, electrical shock, or burn.

 Before using the camera inside an airplane or hospital, check if it is allowed.

Electromagnetic waves emitted by the camera may interfere with the plane’s instruments or the hospital’s medical equipment.

 To prevent a fire and electrical shock, follow the safeguards below:

• Always insert the power plug all the way in.

• Do not handle a power plug with wet hands.

• When unplugging a power plug, grasp and pull the plug instead of the cord.

• Do not scratch, cut, or excessively bend the cord or put a heavy object on the cord. Also do not twist or tie the cords.

• Do not connect too many power plugs to the same power outlet.

• Do not use a cord whose wire is broken or insulation is damaged.

 Unplug the power plug periodically and clean off the dust around the power outlet with

a dry cloth. If the surrounding is dusty, humid, or oily, the dust on the power outlet may become moist and short-circuit the outlet, causing a fire.



Do not connect the battery directly to an electrical outlet or a ca r’s cigarette lighter outlet. The battery may leak, generate excessive heat or explode, causing a fire, burns or injuries.

 A thorough explanation of how to use the product by an adult is required when the

product is used by children. Supervise children while they are using the product. Incorrect usage may result in electrical shock or injury.

 Do not leave a lens or lens-attached camera in the sun without the lens cap attached.

Otherwise, the lens may concentrate the sun’s rays and cause a fire.

 Do not cover or wrap the product with a cloth. Doing so may trap heat within and

cause the casing to deform or catch fire.

 Be careful not to get the camera wet. If you drop the product in the water or if water or

metal get inside the product, promptly remove the battery. This is to prevent a fire and an electrical shock.

 Do not use paint thinner, benzene, or other organic solvents to clean the product.

Doing so may cause fire or a health hazard.

Safety Precautions

Cautions

 Do not use or store the product inside a car under the hot sun or near a heat source.

The product may become hot and cause skin burns. Doing so may also cause battery leakage or explosion, which will degrade the performance or shorten the life of the product.

 Do not carry the camera around when it is attached to a tripod. Doing so may cause

injury. Also make sure the tripod is sturdy enough to support the camera and lens.

 Do not leave the product in a low-temperature environment for an extended period of

time. The product will become cold and may cause injury when touched.

 Never play the provided CD-ROM in a drive that is not compatible with the CD-ROM.

If you use it in a music CD player, you may damage the speakers and other components. When using headphones, there is also a risk of injury to your ears from excessively loud volume.

Follow the cautions below. Otherwise, physical injury or property damage may result.

Handling Precautions

Camera Care

 This camera is a precision instrument. Do not drop it or subject it to physical

shock.

 The camera is not waterproof and cannot be used underwater. If you

accidentally drop the camera into water , promptly consu lt the nearest Canon Service Center. Wipe of f any wat er dr oplets with a dry and clean cloth. If the camera has been exposed to salty air, wipe it with a well -wrung wet cloth.

 Never leave the camera near anything having a strong magnetic field such

as a magnet or electric motor. Also avoid using or leaving the camera near anything emitting strong radio waves, such as a large antenna. S trong magnetic fields can cause camera misoperation or destroy image data.

 Do not leave the camera in excessive heat, such as in a car in direct

sunlight. High temperatures can cause the camera to malfunction.

 The camera contains precision electronic circuitry. Never attempt to

disassemble the camera yourself.

 Do not block the built-in flash, mirror operation with your fin ger , etc. Doing so

may cause a malfunction.

 Use a blower to blow away dust on the lens, viewfinder, reflex mirror, and

focusing screen. Do not use cleaners that contain organic solvents to clean the camera body or lens. For stubborn dirt, take the camera to the nearest Canon Service Center.

 Do not touch the camera’s electrical contacts with your fingers. This is to

prevent the contacts from corroding. Corroded contacts can cause camera misoperation.

 If the camera is suddenly brought in from the cold into a warm room,

condensation may form on the camera and internal parts. To prevent condensation, first put the camera in a sealed plastic bag and let it adjust to the warmer temperature before taking it out of the bag.

 If condensation forms on the camera, do not use the camera. Th is is to avoid

damaging the camera. If there is condensation, remove the lens, card and battery from the camera, and wait until condensa tio n has evaporat ed b efo re using the camera.

 If the camera will not be used for an extended period, remove the battery

and store the camera in a cool, dry, well-ventilated location. Even while the camera is in storage, press the shutter button a few times once in a while to check that the camera is still working.

Handling Precautions

 Avoid storing the camera where there are chemicals that result in rust and

corrosion such as in a chemical lab.

 If the camera has not been used for an extend ed perio d, te st a ll i ts functions

before using it. If you have not used the camera for some time or if there is an important shoot such as a foreign trip coming up, have the camera checked by your nearest Canon Service Center or check the camera yourself and make sure it is working properly.

 If you use continuous shooting, Live Vi ew shooting, or movie shooting for a

prolonged period, the camera may become hot. This is not a malfunction.

 If there is a bright light source inside or outside the image area, ghosting

may occur.

LCD Panel and LCD Monitor

 Although the LCD monitor is manufactured with very high precision

technology with over 99.99% effective pixels, ther e may be a few dead pixels displaying only black or red, etc. among the remaining 0.01% or less pixels. Dead pixels are not a malfunction. They do not affect the images recorded.

 If the LCD monitor is left on for a prolonge d period, scree n burn-in may occu r

where you see remnants of what was displayed. However, this is only temporary and will disappear when the camera is left unused for a few days.

 The LCD monitor display may seem slow in low temperatures, or look black

in high temperatures. It will return to normal at room temperature.

Cards

To protect the card and its recorded data, note the following:

 Do not drop, bend, or wet the card. Do not subject it to excessive force,

physical shock, or vibration.

 Do not touch the card’s electronic contacts with your fingers or anything

metallic.

 Do not affix any stickers, etc., on the card.  Do not store or use the card near anything that has a strong magnetic field,

such as a TV set, speakers, or magnet. Also avoid places prone to having static electricity.

 Do not leave the card in direct sunlight or near a heat source.  Store the card in a case.  Do not store the card in hot, dusty, or humid locations.

Handling Precautions

Contacts

Smudges Adhering to the Front of the Sensor

Besides dust entering the camera from outside, in rare cases lubricant from the camera’s internal parts may adhere to the fr ont of the sensor. If visible spots remain on the image, having the sensor cleaned by a Canon Service Center is recommended.

Lens

After detaching the lens from the camera, put down t he lens with the rear end up and attach the rear lens cap to avoid scratching the lens surface and electrical contacts.

Nomenclature

Built-in flash/AF-assist beam (p.130/100)

Mode Dial (p.27)

<g> ISO speed setting button (p.112)

<6> Main Dial (p.49)

Shutter button (p.48)

Remote control sensor

Grip

Mirror

Contacts (p.21)

Lens mount

Lens lock pin

<Y> External microphone IN terminal

<F> Remote control terminal

<q/C> Audio/video OUT/ Digital terminal (p.164)

<D> HDMI mini OUT terminal

Depth-of-field preview button

Lens release button (p.44)

Red-eye reduction/Selftimer lamp (p.107)

EF Lens mount index (p.43)

Built-in microphones (p.146)

Flash sync contacts

Hot shoe

<D> Flash button (p.130)

<V> Focal plane mark (p.82)

Speaker (p.158)

Strap mount (p.31)

Body cap (p.43)

EF-S Lens mount index (p.43)

Term inal cover

<B> AF area selection button (p.102)

<U> LCD panel illumination button (p.51)

Mode Dial lock-release button (p.49)

Nomenclature

Display-off sensor (p.63)

Viewfinder eyepiece

Eyecup

<B> Info button (p.63, 94, 134, 149)

<M> Menu button (p.55)

LCD monitor/ Touch screen (p.55/58, 156, 159)

Tripod socket

<x> Playback button (p.94)

<5> Quick Control Dial (p.50)

<WB> White balance selection button (p.114) <XA> Picture Style selection button (p.113) <YQi> Drive mode selection button (p.106, 107) <Zf> AF operation selection button (p.98)

<Q> Quick Control button (p.53)

Dioptric adjustment knob (p.47)

<A> Live View shooting/ Movie shooting button (p.131/146)

<A/I> AE lock/ FE lock button/Index/ Reduce button (p.129/154, 155)

<S/u> AF point selection/ Magnify button (p.103/155)

<L> Erase button (p.160)

Card slot (p.35)

Power switch (p.38)

p (N-Mark)

Serial number

Access lamp (p.36)

DC cord hole

Card slot cover (p.35)

Battery compartment cover release lever (p.34)

Battery compartment cover (p.34)

<0> Setting button (p.55)

Multi function lock switch (p.51)

Nomenclature

Shutter speed Multi function lock (LOCK) (p.51)

Exposure level indicator Exposure compensation amount (p.127) AEB range (p.128) Multi function lock (LOCK) (p.51)

Shooting mode Picture Style

(p.113) AF operation (p.98)

One-Shot AF

AI Focus AF

AI Servo AF

Manual Focus

Quick Control icon (p.54)

Battery check (p.39)

zxcn

White balance (p.114)

Q Auto W Daylight E Shade R Cloudy Y Tungsten light U White fluorescent light I Flash O Custom

Eye-Fi transmission status

Drive mode (p.106, 107)

u Single shooting i Continuous shooting B Silent single shooting M Silent continuous shooting

Q Self-timer:10 sec./Remote control

l Self-timer:2 sec.

q Self-timer:Continuous

u White balance correction

B White balance bracketing

Multi Shot Noise Reduction (p.116)

Possible shots during WB bracketing

Possible shots

Image-recording quality (p.110)

73 Large/Fine 83 Large/Normal 74 Medium/Fine 84 Medium/Normal 7a Small 1/Fine 8a Small 1/Normal

b Small 2 (Fine) c Small 3 (Fine)

1+73

RAW+Large/Fine

1 RAW

Metering mode (p.126)

q Evaluative metering w Partial metering r Spot metering e Center-weighted average

metering

y Flash exposure compensation

Highligh

t tone priority

ISO speed (p.112)

Auto Lighting Optimizer (p.115)

Aperture Multi function lock (LOCK) (p.51)

AF area selection mode (p.101)

Self-timer countdown

GPS connection indicator

Shooting Function Settings (in Creative Zone modes, p.27)

The display will show only the settings currently applied.

LCD Panel

Shutter speed Bulb exposure (buLb) FE lock (FEL) Busy (buSY) Built-in flash recycling (buSY) Multi function lock warning (L) No card warning (Card) Card error (Card) Card full warning (FuLL) Error code (Err) Cleaning image sensor (CLn)

AF point selection (MAF, SEL N, SEL AF)

Aperture

Exposure level indicator

Exposure compensation amount (p.127) AEB range (p.128)

Battery check (p.39)

Wi-Fi function

Possible shots Self-timer countdown Bulb exposure time Possible shots during WB bracketing Card error warning (Err) Error number

ISO speed (p.112)

<A> Highlight tone priority

<g> ISO speed (p.112)

Nomenclature

The display will show only the settings currently applied.

Nomenclature

Shutter speed Bulb exposure (buLb) FE lock (FEL) Busy (buSY) Built-in flash recycling (D buSY) Multi function lock warning (L) No card warning (Card) Card error (Card) Card full warning (FuLL) Error code (Err)

Spot metering circle (p.126)

Single-point AF (Manual selection) (p.101)

Focusing screen

Area AF frame (p.101)

Electronic level (p.67)

<A> AE lock/AEB

in-progress

<D> Flash-ready

Improper FE lock warning

<e> High-speed sync <d> FE lock/FEB in-progress

<y> Flash exposure compensation

Aperture (p.124)

Exposure level indicator

Exposure compensation amount AEB range

Red-eye reduction lamp ON

<A> Highlight tone priority

ISO speed

<0> Monochrome shooting

Maximum burst

<o> Focus indicator

<u> White

balance correction

<g>

ISO speed

Flicker detection (p.120)

Grid (p.65)

AF point (p.101)

19-point automatic selection AF (p.101)

Zone AF (Manual selection of zone) (p.101)

Aspect ratio line

AF point selection (M AF , SEL N, SEL AF)

Viewfinder Information

The display will show only the settings currently applied.

Mode Dial

Basic Zone

All you do is press the shutter button. The camera sets everything to suit the subject or scene for shooting.

Creative Zone

These modes give you more control for shooting various subjects as desired.

d : Program AE (p.122) s : Shutter-priority AE (p.123) f : Aperture-priority AE (p.124) a : Manual exposure (p.125)

A : Scene Intelligent Auto (p.70) 7 : Flash Off (p.75)

C : Creative Auto (p.76)

2 : Portrait (p.80) 3 : Landscape (p.81) 4 : Close-up (p.82) 5 : Sports (p.83) 8: Special scene (p.84)

C : Kids (p.85) P : Food (p.86) x : Candlelight (p.87) 6 : Night Portrait (p.88) F : Handheld Night Scene (p.89) G : HDR Backlight Control (p.90)

Y ou can set the shooting mode. T urn the Mode Dial while holding down the Mode Dial center (Mode Dial lock release button).

Nomenclature

Focusing ring (p.105, 142)

Focus mode switch (p.43)

Zoom position index (p.44)

Hood mount (p.45)

Filter thread (front of lens)

Zoom ring (p.44)

Image Stabilizer switch (p.46)

Lens mount index (p.43)

Contacts (p.21)

Zoom ring lock lever (p.44)

Lens without a Distance Scale

Battery Charger LC-E17

Power plug

Charge lamp

Full-charge lamp Battery pack slot

IMPORTANT SAFETY INSTRUCTIONS-SAVE THESE INSTRUCTIONS. DANGER-TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, CAREFULLY FOLLOW THESE INSTRUCTIONS.

For connection to a supply not in the U.S.A., use an attachment plug adapter of the proper configuration for the power outlet, if needed.

Power cord

Power cord socket

Battery pack slot

Charge lamp

Full-charge lamp

Charger for Battery Pack LP-E17 (p.32).

Battery Charger LC-E17E

Charger for Battery Pack LP-E17 (p.32).

Nomenclature

+ 198 hidden pages