Read this manual rst. This manual describes the basic machine
settings, operations, and cautions. Be sure to read this manual
before using the machine.
10 1/2"
(265 mm)
20 1/2"
(520 mm)
Driver installation manuals (Included with the drivers):
Read these manuals next. These manuals describe software
installation.
e-Manual (User Manual CD-ROM):
Read the desired chapter to suit your needs. The e-Manual is
categorized by subject to nd desired information easily.
Viewing the e-Manual from the CD-ROM
1 Insert the User Manual CD-ROM in your computer.
2 Select the language.
3 Click [Display].
Depending on the operating system you are using, a security
protection message appears.
If the User Manual CD-ROM has been already inserted in your
computer and the setup screen is not displayed, remove the CD-ROM
and insert it again.
3
Navigating the Menu and Text Input Method
▲▼◀▶OK
Back
Menu#ClearNumeric keys
Navigating the Menu
Item selection or moving the cursor among the menu items
Select an item with [▲] or [▼].
Proceed to the next hierarchy with or [▶]. Return to the
previous hierarchy with (Back) or [◀].
Setting conrmation
. However, when <Apply> appears on the display,
Press
select <Apply>, and then press
.
Turning ON/OFF the Power
ON
OFF
Text Input Method
Changing entry mode
Press
to change the entry mode. You can also change the
entry mode on the display by selecting <Entry Mode> and
pressing .
Entry modeAvailable text
<A>Uppercase alphabetic letters and symbols
<a>Lowercase alphabetic letters and symbols
<12>Numbers
Entering text, symbols, and numbers
Enter with the numeric keys or
Moving the cursor (Entering a space)
Move with [◀] or [▶]. Move the cursor to the end of the text
and press [▶] to enter a space.
Deleting characters
Delete with . Pressing and holding deletes all characters.
Entry mode: <A>Entry mode: <a>Entry mode: <12>
@ . - _ /1
ABCabc2
DEFdef3
GHIghi4
JKLjkl5
MNOmno6
PQRSpqrs7
TUVtuv8
WXYZwxyz9
(Not available)0
(space) @ . / - _ ! ? & $ % # ( ) [ ] { } < >
* + = " , ; : ' ^ ` | \
.
~
(Not available)
• Make sure that the power plug is rmly inserted into the
power outlet.
• Do not connect the USB cable at this time. Connect it
when installing software.
Specifying the Initial Settings
Follow the instructions on the screen to perform the following:
• Set the language
• Set the country and region
• Insert the paper into the paper drawer
• Set the time zone
• Set the date and time
For details on navigating the menu and how to input the
numbers, see “Navigating the Menu and Text Input Method”
(
P.4).
4
Choosing the Method to Connect the
Machine to the Computer
●
Connecting via a LAN
You can connect the machine to the computer through a
wired LAN router. Use a LAN cable to connect the machine
to the router.
Make sure that there are ports available on the router to connect
the machine and the computer.
Have a Category 5 or higher twisted pair LAN cable ready.
●
Connecting via a USB cable
You can connect the machine to the computer using a USB
cable.
Make sure that the USB cable you use has the following mark.
Setting Up the LAN Connection
Connect the LAN cable.
1
The IP address will be automatically congured in 2
minutes. If you want to set the IP address manually, see
the following items.
e-Manual “Network” ▶ “Connecting to a Network” ▶
“Setting IP Addresses”
Download the appropriate drivers from the Canon
2
website (http://www.canon.com/).
Install the drivers on your computer.
3
For details on the installation procedures, see the driver
installation manuals that are included with the drivers.
Proceed to “Setting a Paper Size and Type” (P.6).
Connecting via a LAN
Checking Before the Setup
Internet
Are the computer and the router properly connected using
a LAN cable?
For more information, see the instruction manual for the
network device you are using, or contact the networking
device manufacturer.
Have the network settings on the computer been
completed?
If the computer is not properly congured, you may not use
the wired LAN connection even after completing the following
settings.
NOTE
• When you connect to a network environment that is not
security protected, your personal information could be
disclosed to third parties. Please use caution.
• If you connect through a LAN in the oce, contact your
network administrator.
Router
LAN cable
Connecting via a USB Cable
Connect the USB cable after installing the drivers.
Download the appropriate drivers from the Canon
1
website (http://www.canon.com/).
Install the drivers on your computer.
2
For details on the installation procedures, see the driver
installation manuals that are included with the drivers.
Connect the USB cable.
3
Proceed to “Setting a Paper Size and Type” (P.6).
5
Loading...
+ 11 hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.