Candy FCP886XS User Manual

PAPER TECHNICAL DATA SHEET / KAĞIT MALZEMESİ

E D C B

53418 26.10.18

CL N° REV. DATE

GENERAL TOLERANCE

SPECIFICATION

ISO 2768 - m

BASE CODE

Kağıt malzeme bilgisi eklendi.1-2-7-11-16-20. sayfalar revize edildi./Paper material information has been added.1-2-7-11-16-20 pages have been revised.

TREATMENT

WEIGHT SCALE

MATERIAL

WITHOUT OUR WRITTEN CONSENT IS FORBIDDEN

MATERIALS IN COMPLIANCE WITH REQUIREMENTS

OF EU DIRECTIVE 2002/95/CE + AMENDMENTS

55 gr/m

SIZE

DATE SIGNATURE

DRAWN

26.04.2018

CANDY OVEN

CHECKED

C. FİDANCI

K.ÖZGÜR

FOR

REPLACE No ORIGIN CL No Class Specification

------------

RELEASE LEVEL

PRODUCTION RELEASED

MODIFY DESCRIPTION

PROPERTY OF

NAME

USER MANUAL C HNPTF02 STM

(LOCAL LANGUAGE)

KULLANMA KLAVUZ C HNPTF02 STM

PART CODE

4 2 8 2 7 1 2 2

------------

52669

Y.GÜLTÜRK

MODIFIED BY

SHEET

1/1

SC 000-000

OVENS

USER INSTRUCTIONS

DESFOURSENCASTRABLES

NOTICE D'EMPLOI ET D'INSTALLATION

CANDY HOOVER GROUP S.R.L. • Via Comolli 16 • 20861 Brugherio (MB) - Italy

Safety Indications

• During cooking, moisture may condense inside the oven cavity or on the glass of the door. This is a normal condition. To reduce this effect, wait 10-15 minutes after turning on the power before putting food inside the oven. In any case, the condensation disappears when the oven reaches the cooking temperature.

• Cook the vegetables in a container with a lid instead of an open tray.

•Avoid leaving food inside the oven after cooking formore than 15/20 minutes.

• WARNING: the appliance and accessible parts become hot during use. Be careful not to touch any hot parts.

•WARNING: the accessible parts can become hot when the oven is in use. Children must be kept at a safe distance.

•WARNING: ensure that the appliance is switched off before replacing the bulb, to avoid the possibility of electric shocks.

•WARNING: before initiating the automatic cleaning cycle:

- Clean the oven door;

- Remove large or coarse food residues from the inside of the oven using a damp sponge. Do not use detergents;

- Remove all accessories and the sliding rack kit (where present);

- Do not place tea towels

• In ovens with meat probe it is necessary, before making the cleaning cycle, close the hole with the nut provided.Always close the hole with the nut when the meat probe is not used.

• Children under 8 must be kept at a safe distance from the appliance if not continuously supervised.

• Children must not play with the appliance. The appliance can be used by those aged 8 or over and by those with limited physical, sensorial or mental capacities, without experience or knowledge of the product, only if supervised or provided with instruction as to the operation of the appliance, in a safe way with awareness of the possible risks.

• Cleaning and maintenance should not be carried out by unsupervised children.

• Do not use rough or abrasive materials or sharp metal scrapers to clean the oven door glasses, as they can scratch the surface and cause the glass to shatter.

• The oven must be switched off before removing the removable parts and, after cleaning, reassemble them according the instructions.

• Only use the meat probe recommended for this oven.

• Do not use a steam cleaner for cleaning operations.

• Connect a plug to the supply cable that is able to bear the voltage, current and load indicated on the tag and having the earth contact. The socket must be suitable for the load indicated on the tag and must be having the earth contact connected and in operation. The earth conductor is yellow-green in colour. This operation should be carried out by a suitably qualified professional. In case of incompatibility between the socket and the appliance plug, ask a qualified electrician to substitute the socket with another suitable type. The plug and the socket must be conformed to the current norms of the installation country. Connection to the power source can also be made by placing an omnipolar breaker between the appliance and the power source that can bear the maximum connected load and that is in line with current legislation. The yellow-green earth cable should not be interrupted by the breaker. The socket or omnipolar breaker used for the connection should be easily accessible when the appliance is installed.

• The disconnection may be achieved by having the plug accessible or by incorporating a switch in the fixed wiring in accordance with the wiring rules.

• If the power cable is damaged, it must be substituted with a cable or special bundle available from the manufacturer or by contacting the customer service department.

• The type of power cable must be H05V2V2-F.

• Failure to comply with the above can compromise the safety of the appliance and invalidate the guarantee.

•Any excess of spilled material should be removed before cleaning.

• During the pyrolytic cleaning process, surfaces can heat up more than usual, children must therefore be kept at a safe distance.

• The appliance must not be installed behind a decorative door in order to avoid overheating.

• When you place the shelf inside, make sure that the stop is directed upwards and in the back of the cavity. The shelf must be inserted completely into the cavity

• WARNING: Do not line the oven walls with aluminum foil or single-use protection available from stores. Aluminum foil or any other protection, in direct contact with the hot enamel, risk melting and deteriorating the enamel of the insides.

• WARNING: Never remove the oven door seal.

• No additional operation/setting is required inorder to operate the appliance at the rated frequencies.

EN 02

Summary

General Instructions

Product Description

Use of the Oven

1.1 Safety indications

1.2 Electrical safety

1.3 Recommendations

1.4 Installation

1.5 Waste management

1.6 Conformity declaration

2.1 Overview

2.2 Accessories

2.3 First use

3.1 Display description

3.2 Cooking Modes

3.3 Using The Steam Function

Oven Cleaning and Maintenance

Troubleshooting

4.1 General notes on cleaning

4.2 Pyrolysis

4.3 Aquactiva Function

4.4 Maintenance

• Removal and cleaning of grills

• Removal of the oven window

• Removal and cleaning of the glass door

• Changing the bulb

5.1 F.A.Q.

EN 03

1. General Instructions

We thank you for choosingone of our products. For thebest results with your oven, you should read this manual carefully and retain it for future reference. Before installing the oven, take note of the serial number so that you can give it to customer service staff if any repairs are required. Having removed the oven from its packaging, check that it has not been damaged during transportation. If you have doubts, do not use the oven and refer to a qualified technician for advice. Keep all of the packaging material (plastic bags, polystyrene, nails) out of the reach of children. When the oven is switched on for the first time, strong smelling smoke can develop, which is caused by the glue on the insulation panels surrounding theoven heating for thefirst time. This is absolutely normal and, if it occurs, you should wait for the smoke to dissipate before putting food in the oven. The manufacturer accepts no responsibility in cases where the instructions contained in this document are not observed. NOTE: the oven functions, properties and accessories cited in this manual will vary, depending on the model youhave purchased.

1.1 Safety Indications

Only use the oven for its intended purpose, that is only for the cooking of foods; any other use, for example as a heat source, is considered improper and therefore dangerous. The manufacturer cannot be held responsible for any damage resulting from improper, incorrect or unreasonable usage. The use of any electrical appliance implies the observance of some fundamental rules:

- do not pull on the powercable to disconnect theplug from the socket;

- do not touch the appliance withwet or damp handsor feet;

- in general the useof adaptors, multiple sockets andextension cables is not recommended;

- in case of malfunction and/or poor operation, switch off the appliance and do not tamper with it.

1.2 Electrical Safety

ENSURE THAT AN ELECTRICIAN OR QUALIFIED TECHNICIAN MAKES THE ELECTRICAL CONNECTIONS. The power supply to which the oven is connected must conform with the laws in force in the country of installation. The manufacturer accepts no responsibility for any damage caused by the failure to observe these instructions. The oven must be connected to an electrical supply with an earthed wall outlet or a disconnector with multiple poles, depending on the laws in force in the country of installation. The electrical supply should be protected with suitable fuses and the cables used must have a transverse section that can ensure correct supplyto the oven. CONNECTION The oven is supplied witha power cable that shouldonly be connected to an electrical supply with 220-240 Vac 50 Hz power between the phases or between the phase and neutral. Before the oven is connected to the electrical supply, itis important to check:

- power voltage indicated on the gauge;

- the setting of the disconnector. The grounding wire connected to the oven's earth terminal must be connected to the earth terminal of thepower supply. WARNING Before connecting the oven to the power supply, ask a qualified electrician to check the continuity of the powersupply's earth terminal. The manufacturer accepts no responsibility for any accidents or other problems caused by failure toconnect the oven to theearth terminal or by an earth connection that has defectivecontinuity. NOTE: as the oven could require maintenance work, it is advisable to keep another wall socket available so that the oven can be connected to this if it is removed from the space in which it is installed. The power cable must only be substituted by technical service staff or by technicians with equivalent qualifications.

1.4 Installation

The manufacturers have no obligation to carry this out. If the assistance of the manufacturer is required to rectify faults arising from incorrect installation, this assistance is not covered by the guarantee. The installation instructions for professionally qualified personnel must be followed. Incorrect installation may cause harm or injury to people, animals or belongings. The manufacturer cannot be held responsible for such harm or injury. The oven can be located high in a column or under a worktop. Before fixing, you must ensure good ventilation in the oven space to allow proper circulation of the fresh air required for cooling and protecting the internal parts. Make the openings specifiedon last page according to the type of fitting.

1.5 Waste management and environmental protection

This appliance is labelled in accordance with European Directive 2012/19/EU regarding electric and electronic appliances (WEEE). The WEEE contain both polluting substances (that can have a negative effect on the environment) and base elements (that can be reused). It is important that the WEEE undergo specific treatments to

correctly remove and dispose of the pollutants and recover all the materials. Individuals can play an important role in ensuring that the WEEE do not become an environmental problem; it is essential tofollow a few basicrules:

- the WEEEshould not be treatedas domestic waste;

- the WEEE should be taken to dedicated collection areas managed by the towncouncil or a registeredcompany. In many countries, domestic collections may be available for large WEEEs. When you buy a new appliance, the old one can be returned to the vendor whomust acceptit free of charge as aone-off, as long as the appliance is of an equivalent type and has the same functions as the purchased appliance.

SAVINGAND RESPECTINGTHE ENVIRONMENT

Where possible, avoid pre-heating the oven and always try to fill it. Open the oven door as infrequently as possible, because heat from the cavity disperses every time it is opened. For a significant energy saving, switch off the oven between 5 and 10 minutes before the planned end of the cooking time, and use the residual heat that the oven continues to generate. Keep the seals clean and in order, to avoid any heat dispersal outside of the cavity. If you have an electric contract with an hourly tariff, the "delayedcooking" programme makes

energy saving more simple, moving the cooking process to start at the reduced tariff timeslot.

1.3 Recommendations

After each use of the oven, a minimum of cleaning will help keep the oven perfectly clean. Do not line the oven walls with aluminium foil or single-use protection available from stores. Aluminium foil or any other protection, in direct contact with the hot enamel, risks melting and deteriorating the enamel of the insides. In order to prevent excessive dirtying of your oven and the resulting strong smokey smells, we recommend not using the oven at very high temperature. It is better to extend the cooking time and lower the temperature a little. In addition to the accessories supplied with the oven, we advise you only use dishes and baking moulds resistant to very hightemperatures.

1.6 Declaration of compliance

Asapplicable, the parts of this appliance are compliant to: REGULATION(EC) No 1935/2004 on materials and articles intended to come intocontact with food; COMMISSION REGULATION (EC) No 2023/2006 on good manufacturing pratice for materials and articles intended come into contact with food. By placing the mark on this product, we are confirming compliance to all relevant European safety, health and environmental requirements which areapplicable in legislation forthis product.

EN 04

2. Product Description

2.1 Overview

2.2 Accessories

1. Control panel

2. Shelf positions (lateral wire grid if included)

3. Metal grill

4. Drip pan

5. Fan (behind the steel plate)

6. Oven door

1 Drip pan

Collects the residuesthat drip during thecooking of foods onthe grills.

2 Metal grill

Holds baking trays and plates.

3 Lateral wire grids

Lateral wire grid if included.

2.3 First Use

PRELIMINARYCLEANING Clean the oven before using for the first time. Wipe over external surfaces with a damp soft cloth. Wash all accessories and wipe inside the oven with asolution of hot water and washingup liquid. Set the empty ovento the maximum temperature and leaveon for about 1 hour, this will remove anylingering smellsof newness.

EN 05

3. Use of the Oven

3.1 Display description

1. Minute minder

2. Clock setting

3. Cooking time

4. End of cooking

5. Temperature or clock display

6. LCD display adjustment controls

7. Thermostat selector knob

8. Function selector knob

WARNING : the first operation to carry out after the oven has been installedor following the interruption ofpower supply (this is recognizable the display pulsating and showing ) is setting the correcttime. This is achievedas follows.

•Push the centralbutton.

•Set time with"-" "+" buttons.

•Release all buttons.

ATTENTION:The oven willonly operate providing theclock is set.

12:00

FUNCTION

SILENCE

MODE

SET

THE TIME

COOKING

DURATION

END OF

COOKING

HOW TO ACTIVATE HOW TO DEACTIVATE WHAT IT DOES WHY IT IS NEEDED

• Rotate the left function selector to the position " Silence mode “

• Rotate the left function selector to the position “Set the time”.

• Use the buttons " + " or " - " to set the time

• Turn the right function selector to a cooking function

• Rotate the left function selector to the position "Cooking Time Duration”

• Set the time of cooking by using buttons " + " and " - "

• Lighting Auto appears

• Turn the right function selector

to a cooking function

• Rotate the left function selector to the position "End of cooking"

• Set the end time of cooking by using buttons " + " and " - "

• Lighting Auto appears

• Rotate the function selector to

the position OFF.

• Rotate the function selector to the position OFF.

•When the cooking time has elapsed, the oven switch off automatically and the alarm rings for few seconds To stop the cooking functions early, turn the function control to OFF or set the time on 00.00; by rotating the function selector to Cooking Time Duration and by using the buttons " + " and " - “

• When the cooking time has elapsed, the oven switch off automatically.

• To stop the cooking functions early, turn the function control to OFF

• Enables you to turn off the sound of the minute minder.

• Enables you to set the time which appears on the display

• It allows to preset the cooking time required for the recipe chosen.

• When the cooking time is set, turn the function selector toOFF to go back to actual time.

• To view the cooking time selected, turn the left function selector to Cooking Time duration.

• It allows to preset the end of cooking time you want.

• When the cooking time is set, turn the function selector to OFF to go back to actual time.

• To view the cooking time selected, turn the left function selector to End of cooking Time

• To turn off the sound of the minute minder

• To set the time NB : Set the time when you first install your oven or just after a black out (the clock is showing a pulsating 12.00)

• For cooking the desired recipes.

•This function is normally used with the COOKING DURATION function

•For example, the desired food needs to cook for 45 minutes and I want it to be ready for 12.30; in this case: at the end of the set time, the oven automatically switches off and an alarm sounds. Select the desired cooking function. Set the cooking duration to 45 minutes (“-”“+”). Set the end of cooking to 12:30 (“-”“+”). Cooking will automatically begin at 11:45 (12:30 minus 45 minutes), at the end of the set cooking time, the oven will automatically switch off. WARNING: by setting only the end of cooking time, and not the cooking duration, the oven will immediately switch on and switch off at the end of the set cooking time.

MINUTE

MINDER

CHILD

SAFETY

LOCK

• Turn the left function selector to the position Minute Minder.

• Set the time of cooking by using buttons “+”and “-”

• Turn the left function selector to the position Child lock.

• Press the button " + " during 5 seconds

• Child lock is available when " STOP " appears on display

• Set the time on 00.00 by turning the left function selector to the position Minute Minder, and using the button " - “

• Turn back the left function selector to Child lock and press button " + " during 5 seconds.

• Indication STOP disappears.

EN 06

•Emits an audible signal at the end of a set time.

•During operation, the display shows the remaining time.

• The oven cannot be used.

• Allow to use the oven as

alarm even if the oven is switch off

• This function is useful when there are children in the house.

+ 14 hidden pages