Campbell Hausfeld PW1805 Operating Instructions And Parts List Manual
Electric Pressure
Washer
Please read and save these instructions. Read carefully before attempting to assemble,
install, operate or maintain the product described. Protect yourself and others by
observing all safety information. Failure to comply with instructions could result in
personal injury and/or property damage! Retain instructions for future reference.
IN470100AV 12/09
Specifications
Maximum
Inlet
Cleaning Maximum Maximum Water Unit
Model Power Pressure Capacity Temp. Voltage Amperage Weight
Operating Instructions and Parts List PW1805
PW1805 2700 1800 psi 1.5 GPM 100˚F 120V 14 Amps 22 lbs.
For parts, product & service information
visit www.chpower.com
© 2009 Campbell Hausfeld/Scott Fetzer
Figure 1
This manual contains information that
is very important to know and
understand. This information is
provided for SAFETY and to PREVENT
EQUIPMENT PROBLEMS. To help
recognize this information, observe the
following symbols.
Warning indicates
a potentially
hazardous situation which, if not
avoided, COULD result in death or
serious injury.
Caution indicates a
potentially
hazardous situation which, if not
avoided, MAY result in minor or
moderate injury.
NOTE or NOTICE: Information that
requires special attention.
Safety Guidelines
470100_1209.qxd 12/11/09 2:34 PM Page 1
SA
VE THESE INSTRUCTIONS
When using this product, basic
precautions should always be followed,
including the following:
1. Read all instructions before using the
product.
2. ALWAYS disconnect power before
disassembling or repairing the unit.
3. Follow all safety codes as well as the
Occupational Safety and Health Act
(OSHA).
4. Ensure safety devices are operating
properly before each use. DO NOT
remove or modify any part of the gun
or unit.
5. Know how to stop this product and
bleed pressure quickly. Be thoroughly
familiar with the controls.
6. Stay alert – watch what you are doing.
7. Do not operate the product when
fatigued or under the influence of
alcohol or drugs.
8. Keep operation area clear of all
persons.
9. Do not overreach or stand on
unstable support. Keep good footing
and balance at all times.
10. Follow the maintenance instructions
specified in the manual.
11. This product is provided with a ground
fault circuit interrupter, GFCI, be sure
to inspect cord and GFCI prior to use.
Any repair or replacement of the
power cord must be performed by a
qualified (licensed or certified)
electrical technician.
12. Never use an extension cord with this
product.
2
www.chpower.com
Operating Instructions and Parts List PW1805
Important Safety Instructions
! IMPORTANT !
This pressure washer is equipped with a
microswitch sensitive to water flow. This
Instant Start/Stop switch (ISS) senses
water flow in the pump. When the trigger is released, water stops flowing
through the pump. The ISS then automatically turns the motor off to protect
pump from overheating.
OPERATION
1. Pull trigger on gun.
2. Turn the “ON/OFF” switch to “ON”.
3. Release trigger. The pressure washer
motor will stop running.
4. To spray again, pull trigger and motor
and pump will restart.
Note: Occasionally the motor may run
for a short time to bring fresh, cool
water into the pump even if trigger is
released. This is part of normal operation and will not damage the unit.
Always turn the
“ON/OFF” switch
to “OFF” then trigger gun to release
hose pressure before unplugging
power cord.
Risk of equipment
damage. Always
make sure the “ON/OFF” switch on the
unit is “OFF” and unit is unplugged
prior to storage.
Risk of Injection.
Unit will start
spraying when trigger is squeezed if
ON/OFF switch is in “ON” position.
Always point gun in safe direction.
Call 1-800-330-0712
for Technical Service
470100_1209.qxd 12/11/09 2:34 PM Page 2
• Discharge pressure – When ‘on/off’
switch is in “off” position, pressure may
still exist in unit. To discharge pressure,
point gun is safe direction and squeeze
trigger.
Risk of explosion
• Do not spray flammable liquids.
• Never use in areas containing
combustible dust, liquids, or vapors.
• High pressure - Gun kicks back – Hold
gun with both hands.
• Keep hose away from sharp objects.
Bursting hoses may cause injury.
Examine hose regularly and replace if
damaged. Do not attempt to mend a
damaged hose.
NOTICE
• Use only detergents specifically
formulated for pressure washers. Always
follow detergent manufacturer’s label
recommendations for proper use of
detergents. Always protect eyes, skin,
and respiratory system from detergent.
• For either indoor or outdoor use. Store
indoors and where temperature stays
above freezing.
• Unplug unit when not in use.
• Pressure washer is not meant to pump
hot water. Do not connect to hot water
supply.
• Never leave the unit unattended while
it is plugged in.
• Always turn water supply “ON” before
turning pressure washer “ON.” Running
pump dry causes damage.
3
www.chpower.com
Operating Instructions and Parts List PW1805
13. The power cord on this product
contains chemicals, including lead,
known to the State of California to
cause [cancer and] birth defects or
other reproductive harm. Wash hands
after handling.
14. To reduce the risk of injury, close
supervision is necessary when a
product is used near children.
Risk of electrocution
• Inspect cord before using - Do not use if
cord is damaged.
• Keep all electrical connections dry and
off the ground.
• Do not touch plug with wet hands.
• This product is provided with a ground
fault circuit interrupter built into the
power cord plug. If replacement of the
plug or cord is needed, use only
identical replacement parts.
• Do not spray electrical apparatus and
wiring.
Risk of injection or sever injury
• High pressure. Keep clear of nozzle. Do
not discharge streams at persons or
animals.
• Never put hand or fingers over spray tip
while operating the unit.
• Never try to stop or deflect leaks with
any body part.
• Always engage the trigger safety latch
in the safe position when spraying is
stopped even if only for a few moments.
• Point gun in safe direction. Unit will
start spraying when trigger is squeezed
if “on/off” switch is in “ON” position.
470100_1209.qxd 12/11/09 2:34 PM Page 3
Do not spray
electrical apparatus and wiring.
• Never disconnect the high pressure
discharge hose from the machine while
the system is pressurized. To
depressurize machine, turn power and
water supply off, then press gun trigger
2-3 times.
• Never permanently engage the trigger
mechanism on the gun.
• Never operate the machine without all
components properly connected to the
machine (handle, gun/wand assembly,
nozzle, etc.).
Equipment damage.
• ALWAYS turn water supply “ON” before
turning pressure washer “ON.” Running
pump dry causes serious damage.
• Do not operate the pressure washer
with the inlet water screen removed.
Keep screen clear of debris and
sediment.
• NEVER operate pressure washer with
broken or missing parts. Check
equipment regularly and repair or
replace worn or damaged parts
immediately.
• Use only the nozzle supplied with this
machine.
• Never leave the wand unattended while
the machine is running.
• Never attempt to alter factory settings.
Altering factory settings could damage
the unit and will void the warranty.
• Always hold gun and wand firmly when
starting and operating the machine.
• NEVER allow the unit to run with the
trigger released (off) for more than one
(1) minute. Resulting heat buildup will
damage pump.
4
www.chpower.com
Operating Instructions and Parts List PW1805
In a double-insulated product, two systems of insulation are provided instead of
grounding. No grounding means are provided for a double-insulated product, nor
should grounding means be added to the
product. Servicing a double-insulated
product requires extreme care and knowledge of the system, and should be done
only by qualified service personnel.
Replacement parts for a double-insulated
product must be identical to the original
parts. A double-insulated product is
marked with the words “Double
Insulation” or “Double Insulated.”
Product may also be marked with symbol
shown below.
Do not use pressure
that exceeds the operating pressure of
any of the parts (hoses, fittings, etc.) in
the pressurized system. Ensure all
equipment and accessories are rated to
withstand the maximum working
pressure of the unit.
Explosion hazard.
• NEVER spray flammable liquids or use
pressure washer in areas containing
combustible dust, liquids or vapors.
• Never operate this machine in a closed
building or in or near an explosive
environment
Servicing of a DoubleInsulated Appliance
Double Insulated symbol
470100_1209.qxd 12/11/09 2:34 PM Page 4
3. The spray gun should be locked into the
"OFF" position by locating the safety
trigger lock just above the trigger of
the gun. Activate the lock by holding
the gun and push the lock from left to
right. Squeeze trigger to make sure the
trigger does not move. The safety trigger lock should be locked at all times
when pressure washer is not in use.
5
www.chpower.com
Operating Instructions and Parts List PW1805
• Pressure washer is not meant to pump
hot water. NEVER connect it to a hot
water supply as it will significantly
reduce the life of the pump.
• NEVER store the pressure washer
outdoors or where it could freeze. The
pump will be seriously damaged.
• Release trigger when changing from
high to low pressure modes. Failure to
do so could result in damage
Keep hose away from
sharp objects. Bursting hoses may cause
injury. Examine hoses regularly and
replace if damaged. Do not attempt to
mend a damaged hose.
Garden Hose Connection
Instructions
1. Attach swivel adapter to pump water
inlet, if not already attached. Notice
the swivel adapter is marked with the
words pump and hose. Make sure to
connect pump side of adapter to pump
water inlet to prevent damage to the
threads.
2. Attach garden hose to swivel adapter
side marked hose.
Figure 2 - Garden Hose Connection
Garden
Hose
Swivel
Adapter
Power Cord
1. Plug the power cord into a grounded
120V outlet and press the reset
button as shown in Figure 3.
2. THIS MUST BE DONE EACH TIME THE
UNIT IS PLUGGED IN AN OUTLET.
Reset
Figure 3 - Grounded plug/reset button
470100_1209.qxd 12/11/09 2:34 PM Page 5
Operating Instructions and Parts List PW1805
6
www.chpower.com
Directions for Use
Damage to cleaning surfaces occurs
because the impact force of the water
exceeds the durability of the surface. You
can vary the impact force by controlling
the nozzle’s fan pattern, the nozzle’s
angle to the cleaning surface, and the
nozzle’s distance from the cleaning
surface. Never use a narrow high impact
stream or a turbo nozzle on a surface that
is susceptible to damage. Avoid spraying
windows with a narrow high impact
stream or turbo nozzle. Doing so may
break the window. The surest way to
avoid damaging surfaces is to follow these
steps:
1. Before triggering the gun, adjust the
nozzle to a wide fan pattern.
2. Place the nozzle approximately
4-5 feet away from the cleaning
surface. Then hold the nozzle at a 45°
angle to the cleaning surface. Trigger
the gun.
3. Vary the fan pattern spray angle and
the distance to the cleaning surface
until optimum cleaning efficiency is
achieved without damaging the
surface.
1. Insert lance into the gun and turn
clockwise to positive stop as shown in
Figure 4.
2. Attach the high pressure hose onto the
gun by turning clockwise and tighten
with a wrench.
3. Be sure that the power switch is in the
“OFF” position.
4. Attach the high pressure hose onto the
pump water outlet by turning clockwise
and hand tightening.
5. Connect garden hose as explained
under Garden Hose Connection
Instructions.
6. Plug the power cord into a grounded
120V outlet.
7. Turn water on.
8. Unlock trigger lock by moving lock
right to left.
9. Depress and hold the trigger on the
gun for one minute to release pressure
and remove any air trapped in the system.
10.Turn the “ON/OFF” switch to the “ON”
position.
System Connection
Figure 4 - Gun/Lance Connection
How to Avoid Damaging
Surfaces
Nozzle Cleaning Instructions
A clogged or partially clogged nozzle can
cause a significant reduction of water
coming out of the nozzle and cause the
unit to pulsate while spraying.
To clean out the nozzle:
• Turn off unit.
• Turn off water supply. Relieve any
pressure trapped in the hose by
squeezing trigger 2-3 times.
470100_1209.qxd 12/11/09 2:34 PM Page 6
The use of detergents can dramatically
reduce cleaning time and assist in the
removal of difficult stains. Some
detergents have been customized for
pressure washer use on specific cleaning
tasks. These detergents are approximately
as thick as water. The use of thicker
detergents, such as dish soap, will clog the
chemical injection system and prevent the
application of the detergent.
The cleaning power of detergents comes
from applying them to a surface and
giving the chemicals time to break down
the dirt and grime. Detergents work best
when applied at low pressure.
The combination of chemical action and
high pressure rinsing is very effective. On
vertical surfaces, apply the detergent
starting at the bottom and work your way
upward. This will prevent the detergent
from sliding down and causing streaks.
High pressure rinsing should also progress
from the bottom to top. On particularly
tough stains, it may be necessary to use a
brush in combination with detergents and
high pressure rinsing.
7
www.chpower.com
Operating Instructions and Parts List PW1805
• Separate lance from gun.
• Rotate nozzle to the narrow stream
setting. This opens up the fan blades.
• Using the included tip cleaner, or an
un-folded paper clip, insert wire into
the nozzle hole and move back and
forth until debris is dislodged (refer to
Figure 5).
• Remove additional debris by backflushing water through the nozzle. To
do this, remove the lance from the
gun, place end of a garden hose (with
water running) to tip of nozzle
pushing water and debris out the back
opening of the lance.
Nozzle Cleaning Instructions
(Continued)
Detergents
Tip Cleaner
Nozzle
Figure 5
Figure 6
Water
outlet
Water
inlet
GFCI
Plug
ON/OFF
switch
Garden
hose
Gun
High
pressure
hose
Swivel
Adapter
Lance
470100_1209.qxd 12/11/09 2:34 PM Page 7
Operating Instructions and Parts List PW1805
8
www.chpower.com
1. The lance is affected by pressure during
operation; therefore hold it firmly with
both hands and point the nozzle
toward the ground.
2. Activate by pulling the trigger of the
gun/spray handle.
3. Adjust the distance to the cleaning surface, which will also adjust your pressure of the nozzle.
4. Spray pattern shape and intensity can
be changed by twisting the spray
adjuster at the end of the lance. Keep
hands clear of the front of the lance to
prevent injury. See figure 7.
Operation
Notes
Figure 7 - Spray Adjust
END OF OPERATION
1. Press the ON/OFF switch to “OFF” on
the pressure washer.
2. Disconnect the plug from the power
source.
3. Shut off the water supply.
4. Activate the spray handle to relieve the
machine of pressure.
5. Lock the trigger into the “OFF”
position.
470100_1209.qxd 12/11/09 2:34 PM Page 8
Ref. Part
No. Description Number Qty.
Replacement Parts List
For Replacement Parts or Technical
Assistance, Call 1-800-330-0712
1 Swivel Adapter PM350100SV 1
2 Filter PM350101SV 1
3 Pump Inlet N/A 1
4 Switch N/A 1
5 Gun Holder PM350111SV 1
6 Tip Cleaner PM008500AV 1
7 Turbo Nozzle PM350108SV 1
8 Adjustable Fan Lance PM350104SV 1
9 Gun PM350109SV 1
10 Hose PM350110SV 1
11 Hose Holder PM350112SV 1
12 Handle PM350114SV 1
13 Power Cord Holder PM350113SV 1
14 Pump Outlet N/A 1
15 Detergent Bottle PM350105AV 1
16 O-Ring PM232200SV 3
Please provide following information:
- Model number
- Serial number (if any)
- Part description and number as
shown in parts list
Address parts correspondence to:
Campbell Hausfeld
Attn: Customer Service
100 Mundy Memorial Drive
Mt. Juliet, TN 37122 U.S.A.
12
2
1
3
4
5
6
7
8
9
10
11
Operating Instructions and Parts List PW1805
9
www.chpower.com
13
14
15
16
16
16
470100_1209.qxd 12/11/09 2:34 PM Page 9
Operating Instructions and Parts List PW1805
10
www.chpower.com
Limited Warranty
1. DURATION: From the date of purchase by the original purchaser as follows: One Year.
2. WHO GIVES THIS WARRANTY (WARRANTOR): Campbell Hausfeld / Scott Fetzer Company, 100 Production Drive,
Harrison, Ohio 45030, Telephone: (800) 330-0712
3. WHO RECEIVES THIS WARRANTY (PURCHASER): The original purchaser (other than for purposes of resale) of the
Campbell Hausfeld pressure washer.
4. WHAT PRODUCTS ARE COVERED UNDER THIS WARRANTY: Any Campbell Hausfeld Pressure Washer supplied or
manufactured by the Warrantor.
5. WHAT IS COVERED UNDER THIS WARRANTY: Substantial defects on material and workmanship which occur
within the duration of the warranty period with the exceptions noted below. Warrantor will also cover normal
wear items for a period of 90 days from the date of original purchase against defects in material and
workmanship. These wear items include high pressure hoses, water and oil seals, o-rings, valves, lances, and
spray tips.
6. WHAT IS NOT COVERED UNDER THIS WARRANTY:
A.Implied warranties, including those of merchantability and FITNESS FOR A PARTICULAR PURPOSE ARE
LIMITED FROM THE DATE OF ORIGINAL PURCHASE AS STATED IN THE DURATION. If this pressure washer is
used for commercial, industrial or rental purposes, the warranty will apply for ninety (90) days from the date
of purchase. Some States do not allow limitation on how long an implied warranty lasts, so the above
limitations may not apply to you.
B. ANY INCIDENTAL, INDIRECT, OR CONSEQUENTIAL LOSS, DAMAGE, OR EXPENSE THAT MAY RESULT FROM
ANY DEFECT, FAILURE, OR MALFUNCTION OF THE CAMPBELL HAUSFELD PRESSURE WASHER. Some States do
not allow the exclusion or limitation of incidental or consequential damages, so the above limitation or
exclusion may not apply to you.
C. Any failure that results from shipping damage, accident, purchaser’s abuse, neglect or failure to install and
operate pressure washer in accordance with instructions provided in the owner’s manual(s) supplied with
product.
D.Pre-delivery service, i.e. assembly, oil or lubricants and adjustment.
E. Items or service normally required to maintain the pressure washer.
F. Gasoline engine and components are expressly excluded from coverage under this limited warranty. Such
components should be returned by the purchaser to the original manufacturer or to its authorized repair
stations for service.
G. Additional items not covered under the warranty:
1. Motor brushes (Electric models only).
2. Cosmetic defects that do not interfere with functionality.
3. Rusted components.
4. Pump wear or valve damage caused by using improper oil, oil contamination or by failure to follow proper
oil maintenance guidelines.
7. RESPONSIBILITIES OF WARRANTOR UNDER THIS WARRANTY: Repair or replace, at Warrantor’s option, pressure
washer or component which is defective, has malfunctioned and/or failed to conform within duration of the
warranty period.
8. RESPONSIBILITIES OF PURCHASER UNDER THIS WARRANTY:
A. Provide dated proof of purchase and maintenance records.
B. Call Campbell Hausfeld (800-330-0712) to obtain your warranty service options. Freight costs must be borne
by the purchaser.
C. Use reasonable care in the operation and maintenance of the pressure washer as described in the owner’s
manual(s).
9. WHEN WARRANTOR WILL PERFORM REPAIR OR REPLACEMENT UNDER THIS WARRANTY: Repair or replacement
will be scheduled and serviced according to the normal work flow at the servicing location, and depending on
the availability of replacement parts.
This Limited Warranty applies in the U.S., Canada and Mexico only and gives you specific legal rights. You may also
have other rights which vary from state to state or country to country.
470100_1209.qxd 12/11/09 2:34 PM Page 10
Pulvérisateur de
Lavage Électrique
S’il vous plaît lire et conserver ces instructions. Lire attentivement avant de monter,
installer, utiliser ou de procéder à l’entretien du produit décrit. Se protéger ainsi que les
autres en observant toutes les instructions de sécurité, sinon, il y a risque de blessure et /
ou dégâts matériels ! Conserver ces instructions comme référence.
Manuel d’instructions et pièces de rechange PW1805
IN470100AV 12/09
11 Fr
Spécifications
Température
Max. Poids
Pouvoir de Pression Capacité d’Eau du
Modèle nettoyage Maximum Maximum d’Arrivée Tension Ampérage Modèle
PW1805 70 613 12 410 kPa 5,69 L/min 38° C 120V 14 A 9,98 kg
© 2009 Campbell Hausfeld/Scott Fetzer
Directives de Sécurité
Ce manuel contient de l’information
très importante qui est fournie
pour la SÉCURITÉ et pour ÉVITER LES
PROBLÈMES D’ÉQUIPEMENT.
Rechercher les symboles suivants pour
cette information.
Avertissement
indique une situation hasardeuse
potentielle qui, si elle n’est pas évitée,
PEUT résulter en perte de vie ou
blessures graves.
Attention indique
une situation hasardeuse potentielle
qui, si elle n’est pas évitée, PEUT résulter
en blessures.
REMARQUE ou AVIS:
L’information qui exige une attention
spéciale.
Figure 1
470100_1209.qxd 12/11/09 2:34 PM Page 11
Loading...