Campbell Hausfeld PW1686 User Manual

Assembly Instructions and Parts List PW1686
1
2
3
3
4
Please read and save these instructions. Read carefully before attempting to assem­ble, install, operate or maintain the product described. Protect yourself and others by observing all safety information. Failure to comply with instructions could result in personal injury and/or property damage! Retain instructions for future reference.
Electric Pressure Washer
NOTE: REFER TO PRODUCT MANUAL FOR ALL SAFETY INSTRUCTIONS
Specifications
Max Pressure Motor Maximum
with Power Inlet
Cleaning Standard Maximum (Single Water Unit
Model Power Lance Capacity Phase) Voltage Temp. Weight
PW1686 2640 1650 psi 1.6 GPM 14 Amps 120V 100˚F 38 lbs.
Assembly Instructions
1. Attach detergent suction tube to hose barb on detergent tank and put cap on detergent tank (Figure
1).
2. Slide accessory storage bracket onto back of pressure washer (Figure 1).
3. Slide cord holder and lance storage collar onto side of pressure washer (Figure 1).
4. Align handle on back of pressure washer and attach using screws pro­vided (Figure 1).
Figure 1
5. Assemble one wheel to axle and slide through back of pressure wash­er and detergent tank (Figure 2).
© 2003 Campbell Hausfeld
Figure 2
For parts, product & service information
visit
www.chpower.com
Assembly Instructions and Parts List PW1686
Assembly Instructions (Continued)
6. Assemble second wheel to axle (Figure 3).
7. Attach hose holder with screws pro­vided (Figure 4).
8. Attach lance storage holder with screw provided (FIgure 5).
9. Align hub cap locking tabs with wheels and press into place (Figure
5).
Figure 3
Figure 4
Figure 5
www.chpower.com
2
"A"
!
WARNING
!
CAUTION
!
CAUTION
Assembly Instructions and Parts List PW1686
Reset
Garden Hose Connection
GARDEN HOSE CONNECTION INSTRUCTIONS
1. Attach nipple adapter to inlet fitting on the unit (this may already be attached to the pump).
2. Attach quick connect fitting to gar­den hose.
3. Pull side “A” of quick connect fitting toward garden hose and push onto nipple adapter.
4. Push side “A” of quick connect fitting towards nipple adapter and release.
Quick Connect Fitting
Garden Hose
Nipple Adapter
Figure 6 - Garden Hose Connection
! IMPORTANT !
This pressure washer is equipped with a microswitch sensitive to water flow. This Instant Start/Stop switch (ISS) senses water flow in the pump. When the trig­ger is released, water stops flowing through the pump. The ISS then auto­matically turns the motor off to protect pump from overheating.
OPERATION
1. Pull trigger on gun.
2. Turn the “ON/OFF” switch to “ON”.
3. Release trigger. The pressure washer motor will stop running.
4. To spray again, pull trigger and motor and pump will restart.
Note: Occasionally the motor may run for a short time to bring fresh, cool water into the pump even if trigger is released. This is part of normal opera­tion and will not damage the unit.
Power Cord
1. Plug the power cord into a ground­ed 120V outlet and press the reset button as shown in Figure 7.
2. THIS MUST BE DONE EACH TIME THE UNIT IS PLUGGED IN AN OUTLET.
Figure 7 - Grounded plug/reset button
Always turn the
“ON/OFF” switch to “OFF” then trigger gun to release hose pres­sure before unplugging power cord.
Risk of equipment dam-
age. Always make sure the “ON/OFF” switch on the unit is “OFF” and unit is unplugged prior to storage.
Risk of Injection.
Unit will start spraying when trigger is squeezed if on/off switch is in “ON” position. Always point gun in safe direction.
Call 1-800-330-0712
for Technical Service
www.chpower.com
3
13 mm
OUTLET
INLET
Assembly Instructions and Parts List PW1686
13 mm
OUTLET
INLET
System Connection
1. Insert lance into the gun and turn clockwise to positive stop as shown in Figure 8.
Figure 8 - Gun/Lance Connection
2. Ensure that the power switch is in the “OFF” position.
3. Attach the high pressure hose and gun assembly to the unit.
4. Connect garden hose as explained under
Instructions
Garden Hose Connection
.
5. Plug the power cord into a grounded 120V outlet, that is on a dedicated circuit.
6. Turn water on.
7. Depress and hold the trigger on the gun for one minute to release pres­sure and remove any air trapped in the system.
8. Turn the “ON/OFF” switch to the “ON” position.
NOTE: REFER TO PRODUCT MANUAL FOR OPERATING INSTRUCTIONS
High Pressure Hose
Figure 9
Gun
On/Off Switch
Garden Hose
www.chpower.com
4
Assembly Instructions and Parts List PW1686
Replacement Parts List
For Replacement Parts, Call 1-800-330-0712
8
9
10
9
19
12
Please provide following information:
-Model number
-Serial number (if any)
-Part description and number as shown in parts list
Address parts correspondence to:
The Campbell Group / Parts Dept. 100 Production Drive Harrison, OH 45030 U.S.A.
20
2
11
9
4
3
5
1
16
17
18
13
14
15
6
7
Ref. Part No. Description Number Qty.
1 Adjustable pressure lance PM271080SV 1 2 Turbo lance PM022621AV 1 3 Hose PM243600AV 1 4 Gun PM037201SJ 1 5 Nipple adapter PM022100AV 1 6 Quick connect fitting PM020600SV 1 7 Tip cleaner PM008500AV 1 8 Handle PM271000SV 1 9 Hardware pack PM271010SV 1 10 Lance storage collar PM271020SV 1 11 Accessories storage bracket PM271030SV 1 12 Lance storage holder PM271040SV 1 13 Hose holder PM270050SV 1 14 Detergent tank cap PM060000SV 1 15 Detergent tank PM271050SV 1 16 Wheel cover PM066300SV 2 17 Wheel PM066301SV 2 18 Axle PM271060SV 1 19 Cord holder PM271070SV 1 20 O-ring PM232200SV 1
www.chpower.com
5
Loading...