Campbell Hausfeld PW167612AV User Manual

Max Pressure with Effective Pressure Maximum Motor Power Maximum Inlet Unit

Model Standard Lance w/Turbo Lance Capacity (Single Phase) Voltage Water Temperature Weight

Electric Pressure
Washer

Please read and save these instructions. Read carefully before attempting to assemble, install, operate or maintain the product described.
Protect yourself and others by observing all safety information. Failure to comply with instructions could result in personal injury and/or prop­erty damage! Retain instructions for future reference.

Specifications

PW167612AV 1600 psi 1750 psi 1.6 GPM 14.5 Amps 120 V 100˚F 39 lbs.

Installation Instructions

Assembly Instructions and Parts List PW167612AV

NOTE: REFER TO PRODUCT MANUAL FOR
ALL SAFETY INSTRUCTIONS

Tools Required for Installation:

● Flat Screwdriver

● Hammer/Mallet

● Adjustable Wrench

1. Set plastic spacer (included in parts
pack) on workbench (Figure 1).

2. Place “star shaped” retaining ring on
the spacer (tangs pointing down)
(Figure 2).

3. Tap the retaining ring onto the axle
(Figure 3 & 4).

4. Put both wheels on axle, solid sides
together (Figure 5).

5. Attach opposite ring in the same
manner (Figure 6).

6. Slide wheels out and snap axle into
place on the underside of body
(Figure 7).

7. Snap wheel covers on the wheel.

8. Attach foot to front of pressure wash­er body (Figure 7).

9. Hook up chemical suction hose to the
tip on the bottom of the handle
(Figure 8).

10. Attach black handle with enclosed
screws and washers (Figure 9).

Figure 1

IN457001AV 2/03

Approved

Figure 2

Figure 4

Figure 5

Figure 6

Figure 7

Figure 9

Figure 8

Figure 3

Solid
Sides

© 2003 Campbell Hausfeld/Scott Fetzer

For parts, product & service information

visit www.chpower.com

U

L

Garden Hose Connection

GARDEN HOSE CONNECTION
INSTRUCTIONS

1. Attach nipple adapter to inlet fitting
on the unit (this may already be
attached to the pump).

2. Attach quick connect fitting to gar­den hose.

3. Pull side “A” of quick connect fitting
toward garden hose and push onto
nipple adapter.

4. Push side “A” of quick connect fitting
towards nipple adapter and release.

Figure 10 - Garden Hose Connection

Quick Connect Fitting

Garden Hose

Nipple
Adapter

! IMPORTANT !

This pressure washer is equipped with a
microswitch sensitive to water flow. This
Instant Start/Stop switch (ISS) senses
water flow in the pump. When the trig­ger is released, water stops flowing
through the pump. The ISS then auto­matically turns the motor off to protect
pump from overheating.

OPERATION

1. Pull trigger on gun.

2. Turn the “ON/OFF” switch to “ON”.

3. Release trigger. The pressure washer
motor will stop running.

4. To spray again, pull trigger and motor
and pump will restart.

Note: Occasionally the motor may run
for a short time to bring fresh, cool
water into the pump even if trigger is
released. This is part of normal opera­tion and will not damage the unit.

Always turn the

“ON/OFF” switch to “OFF”
then trigger gun to release hose pres­sure before unplugging power cord.

Risk of equipment dam-

age. Always make sure
the “ON/OFF” switch on the unit is
“OFF” and unit is unplugged prior to
storage.

Risk of Injection.

Unit will start spraying
when trigger is squeezed if on/off
switch is in “ON” position. Always
point gun in safe direction.

Call 1-800-330-0712

for Technical Service

Assembly Instructions and Parts List PW167612AV

2

www.chpower.com

Power Cord

1. Plug the power cord into a ground­ed 120V outlet and press the reset
button as shown in Figure 11.

2. THIS MUST BE DONE EACH TIME THE
UNIT IS PLUGGED IN AN OUTLET.

Figure 11 - Grounded plug/reset button

"A"

Reset

!

!

!

CAUTION

CAUTION

WARNING

3

www.chpower.com

Assembly Instructions and Parts List PW167612AV

Figure 13 - Connection Call-Outs

1. Insert lance into the gun and turn
clockwise to positive stop as shown in
Figure 12.

2. Ensure that the power switch is in the
“OFF” position.

3. Attach the high pressure hose and
gun assembly to the unit.

4. Connect garden hose as explained
under Garden Hose Connection
Instructions.

5. Plug the power cord into a grounded
120V outlet, that is on a dedicated
circuit.

6. Turn water on.

7. Depress and hold the trigger on the
gun for one minute to release pres­sure and remove any air trapped in
the system.

8. Turn the “ON/OFF” switch to the
“ON” position.

NOTE: REFER TO PRODUCT MANUAL
FOR OPERATING INSTRUCTIONS

System Connection

Figure 12 - Gun/Lance Connection

Outlet

Electrical Cord
with GFCI

High
Pressure
Hose

Gun

Garden
Hose

Handle/Detergent
Tank

13 mm

Assembly Instructions and Parts List

PW167612AV

4

www.chpower.com

Ref. Part

No. Description Number Qty.

For Replacement Parts,
Call 1-800-330-0712

Replacement Parts List

Please provide following information:

-Model number

-Serial number (if any)

-Part description and number as shown in
parts list

Address parts correspondence to:

The Campbell Group / Parts Dept.
100 Production Drive
Harrison, OH 45030 U.S.A.

1 Adjustable Lance PM257000SV 1

2 Turbo Lance PM257100SV 1

3 Hose PM243600AV 1

4 Gun PM037201AV 1

5 Nipple Adapter PM022100AV 1

6 Quick Connect Fitting PM020600SV 1

7 Tip Cleaner PM008500AV 1

8 Detergent Tank PM059000SV 1

9 Hardware Pack (Upper Handle/Wheels/Front Foot) PM062200SV 1

10 Axle PM062400SV 1

11 Wheels PM059100SV 2

12 Wheel Covers PM059200SV 2

13 Front Foot PM059400AV 1

14 Cap, Detergent Tank PM060000SV 1

1

3

5

4

6

7

2

8

13

10, 11, & 12

14

REPAIR MANUAL FOR

PRESSURE WASHERS

NOW AVAILABLE!

• Step-by-step instructions
lead you through the
removal, inspection and
replacement of key parts

• Jam-packed with pictures,
line art and exploded views

To order call

1-800-330-0712