Campbell Hausfeld PW158010AV User Manual

Lista de Repuestos

Para ordenar repuestos,
sírvase llamer al
1-800-330-0712
(En los Estados Unidos,
o llame a su distribuidor
local)

Instrucciones de Montaje y Lista de Piezas PW158010AV

Electric Pressure
Washer

Please read and save these instructions. Read carefully before attempting to assem­ble, install, operate or maintain the product described. Protect yourself and others by
observing all safety information. Failure to comply with instructions could result in
personal injury and/or property damage! Retain instructions for future reference.

IN463201AV 10/04

© 2004 Campbell Hausfeld

Specifications

PW158010AV 2250 1500 psi 1.5 GPM 13 Amps 120V 100˚F 26 lbs.

Assembly Instructions

Assembly Instructions and Parts List PW158010AV

1. Attach handle with enclosed screws
as shown. The longest screw goes

into the top hole of the handle.

2. Assemble wheels by pushing wheel
fasteners through wheels and into
mounting holes as shown.

3. Attach foot to bottom of pressure
washer as shown.

4. Attach high pressure soap lance
holder with enclosed screws as
shown.

Figure 1

NOTE: REFER TO PRODUCT MANUAL
FOR ALL SAFETY INSTRUCTIONS

For parts, product & service information

visit www.chpower.com

Max Pressure Motor Maximum

with Power Inlet

Cleaning Standard Maximum (Single Water Unit

Model Power Lance Capacity Phase) Voltage Temp. Weight

1 * Lanza de jabón de alta presión — 1
2 Lanza turbo PM022621AV 1
3 Manguera PM243600AV 1
4 Pistola PM037203AV 1
5 Adaptador de manguito PM022100AV 1
6 Conector rápido PM020600SV 1
7 Limpiador de puntas PM008500AV 1
8 Sujetador de rueda PM342200SV 2
9 Rueda PM342210SV 2
10 Soporte delantero PM270040SV 1
11 Soporte de lanza de jabón de alta presión PM342220SV 1
12 Mango PM342230SV 1
13 Paquete de hardware PM270070SV 1
14 Anillo en O PM232200SV 1

* Para las partes de la lanza de jabón de alta presión, ver el manual para la lanza

de alta presión del jabón IN464701AV 11/04, incluido.

No. de Número del
Ref. Descripción Repuesto Ctd.

Longest Screw

1

8

4

2

3

5

6

7

12

11

13

10

8

9

9

13

13

14

14

Sírvase proporcionar la siguiente información:

-Número de modelo

-Número de serie (si lo hubiera)

-Descripción y número del repuesto, según se
indica en la lista de repuestos.

Dirija toda la correspondencia a:

Campbell Hausfeld

Attn: Customer Service
100 Mundy Memorial Drive
Mt. Juliet, TN 37122 U.S.A.

3. Conecte la manguera de alta presión
y el conjunto de pistola en la unidad.

4. Conecte la manguera de jardín según
se explica en Instrucciones de conex­ión de la manguera de jardín.

5. Enchufe el cordón de corriente en un
tomacorrientes de 120 V con conex­ión a tierra, que se encuentre en un
circuito dedicado.

6. Abra la llave del agua.

7. Presione el gatillo y manténgalo pre­sionado por 1 minuto para liberar la
presión y remover el aire atrapado en
el sistema.

8. Mueva el interruptor "ON/OFF"
(“ENCENDIDO/APAGADO”) a la posi­ción "ON" ("ENCENDIDO").

NOTA: PARA OBTENER INSTRUC­CIONES DE OPERACIÓN, CONSULTE
EL MANUAL DEL PRODUCTO.

1. Inserte la lanza en la pistola y gírela
en el sentido de las agujas del reloj
hasta que llegue a su tope, como se
muestra en la Figura 4.

2. Verifique que el interruptor de
energía esté en la posición "OFF"
("APAGADO").

11 Sp

Figura 5

System Connection

Figura 4 - Conexión de la pistola y lanza

Interruptor
"On/Off"
(Encendido/
Apagado)

Pistola

Manguera de
alta presión

Manguera
de jardín

Cable de Corriente Eléctrica
Continuación

Instrucciones de Montaje y Lista de Piezas PW158010AV

2. SE DEBE HACER ESTO CADA VEZ QUE LA

UNIDAD SE ENCHUFE EN UN TOMACOR­RIENTE.

Garden Hose Connection

GARDEN HOSE CONNECTION
INSTRUCTIONS

1. Attach nipple adapter to inlet fitting
on the unit (this may already be
attached to the pump).

2. Attach quick connect fitting to
garden hose.

3. Pull side “A” of quick connect fitting
toward garden hose and push onto
nipple adapter.

4. Push side “A” of quick connect fitting
towards nipple adapter and release.

Figure 2 - Garden Hose Connection

Quick Connect Fitting

Garden Hose

Nipple
Adapter

! IMPORTANT !

This pressure washer is equipped with a
microswitch sensitive to water flow. This
Instant Start/Stop switch (ISS) senses
water flow in the pump. When the trig­ger is released, water stops flowing
through the pump. The ISS then auto­matically turns the motor off to protect
pump from overheating.

OPERATION

1. Pull trigger on gun.

2. Turn the “ON/OFF” switch to “ON”.

3. Release trigger. The pressure washer
motor will stop running.

4. To spray again, pull trigger and motor
and pump will restart.

Note: Occasionally the motor may run
for a short time to bring fresh, cool
water into the pump even if trigger is
released. This is part of normal opera­tion and will not damage the unit.

Always turn the

“ON/OFF” switch to “OFF”
then trigger gun to release hose pres­sure before unplugging power cord.

Risk of equipment dam-

age. Always make sure
the “ON/OFF” switch on the unit is
“OFF” and unit is unplugged prior to
storage.

Risk of Injection.

Unit will start spraying
when trigger is squeezed if on/off
switch is in “ON” position. Always
point gun in safe direction.

Call 1-800-330-0712

for Technical Service

Assembly Instructions and Parts List PW158010AV

2

www.chpower.com

Power Cord

1. Plug the power cord into a grounded
120V outlet and press the reset
button as shown in Figure 3.

2. THIS MUST BE DONE EACH TIME THE
UNIT IS PLUGGED IN AN OUTLET.

Figure 3 - Grounded plug/reset button

ENTRADA

SALIDA

"A"

Reset

!

CAUTION

!

CAUTION

!

WARNING

13 mm

OUTLET

INLET