Brother Innov-is F440E, Innov-is NS1150E Operation Manual

Operation Manual

Embroidery Machine

Product Code: 888-L90/L91/L93/K92

Be sure to read this document before using the machine. We recommend that you keep this document nearby for future reference.

INTRODUCTION

Thank you for purchasing this machine. Before using this machine, carefully read the “IMPORTANT SAFETY INSTRUCTIONS”, and then study this manual for the correct operation of the various functions. In addition, after you have finished reading this manual, store it where it can quickly be accessed for future reference.

IMPORTANT SAFETY INSTRUCTIONS

Please read these safety instructions before attempting to use the machine.

DANGER - To reduce the risk of electrical shock

1Always unplug the machine from the electrical outlet immediately after using, when cleaning, making any user

servicing adjustments mentioned in this manual, or if you are leaving the machine unattended.

WARNING - To reduce the risk of burns, fire, electrical shock, or injury to

persons.

2Always unplug the machine from the electrical outlet when making any adjustments mentioned in the instruction

manual.

• To unplug the machine, switch the machine to the symbol “O” position to turn it off, then grasp the plug and pull it out of the electrical outlet. Do not pull on the cord.

• Plug the machine directly into the electrical outlet. Do not use an extension cord.

• Always unplug your machine if there is a power failure.

3Electrical Hazards:

• This machine should be connected to an AC power source within the range indicated on the rating label. Do not connect it to a DC power source or converter. If you are not sure what kind of power source you have, contact a qualified electrician.

• This machine is approved for use in the country of purchase only.

4Never operate this machine if it has a damaged cord or plug, if it is not working properly, has been dropped or

damaged, or water is spilled on the unit. Return the machine to the nearest authorized Brother dealer for examination, repair, electrical or mechanical adjustment.

• While the machine is stored or in use if you notice anything unusual, such as an odor, heat, discoloration or deformation, stop using the machine immediately and unplug the power cord.

• When transporting the machine, be sure to carry it by its handle. Lifting the machine by any other part may damage the machine or result in the machine falling, which could cause injuries.

• When lifting the machine, be careful not to make any sudden or careless movements, which may cause a personal injury.

IMPORTANT SAFETY INSTRUCTIONS

5Always keep your work area clear:

• Never operate the machine with any air openings blocked. Keep ventilation openings of the machine and foot control free from the build up of lint, dust, and loose cloth.

• Do not use extension cords. Plug the machine directly into the electrical outlet.

• Never drop or insert foreign objects in any opening.

• Do not operate where aerosol (spray) products are being used or where oxygen is being administered.

• Do not use the machine near a heat source, such as a stove or iron; otherwise, the machine, power cord or garment being sewn may ignite, resulting in fire or an electric shock.

• Do not place this machine on an unstable surface, such as an unsteady or slanted table, otherwise the machine may fall, resulting in injuries.

6Special care is required when embroidering:

• Always pay close attention to the needle. Do not use bent or damaged needles.

• Keep fingers away from all moving parts. Special care is required around the machine needle.

• Switch the machine to the symbol “O” position to turn it off when making any adjustments in the needle area.

• Do not use a damaged or incorrect needle plate, as it could cause the needle to break.

7This machine is not a toy:

• Your close attention is necessary when the machine is used by or near children.

• The plastic bag that this machine was supplied in should be kept out of the reach of children or disposed of. Never allow children to play with the bag due to the danger of suffocation.

• Do not use outdoors.

8For a longer service life:

• When storing this machine, avoid direct sunlight and high humidity locations. Do not use or store the machine near a space heater, iron, halogen lamp, or other hot objects.

• Use only neutral soaps or detergents to clean the case. Benzene, thinner, and scouring powders can damage the case and machine, and should never be used.

• Always consult the Operation Manual when replacing or installing needle or other parts to assure correct installation.

9For repair or adjustment:

• If the light unit is damaged, it must be replaced by an authorized Brother dealer.

• In the event a malfunction occurs or adjustment is required, first follow the troubleshooting table in the back of the Operation Manual to inspect and adjust the machine yourself. If the problem persists, please consult your local authorized Brother dealer.

Use this machine only for its intended use as described in the manual.

Use accessories recommended by the manufacturer as contained in this manual.

The contents of this manual and specifications of this product are subject to change without notice.

For additional product information and updates, visit our website at www.brother.com

IMPORTANT SAFETY INSTRUCTIONS

SAVE THESE INSTRUCTIONS

This machine is intended for household use.

FOR USERS IN COUNTRIES EXCEPT EUROPEAN COUNTRIES

This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety. Children should be supervised to ensure that they do not play with the appliance.

FOR USERS IN EUROPEAN COUNTRIES

This appliance can be used by children aged from 8 years and above and persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning use of the appliance in a safe way and understand the hazards involved. Children shall not play with the appliance. Cleaning and user maintenance shall not be made by children without supervision.

FOR USERS IN THE UK, EIRE, MALTA

AND CYPRUS ONLY

IMPORTANT

• In the event of replacing the plug fuse, use a fuse approved by ASTA to BS 1362, i.e. carrying the mark,

rating as marked on plug.

• Always replace the fuse cover. Never use plugs with the fuse cover omitted.

• If the available electrical outlet is not suitable for the plug supplied with this equipment, you should contact your

authorized Brother dealer to obtain the correct lead.

iii

TRADEMARKS

IMPORTANT:

READ BEFORE DOWNLOADING, COPYING, INSTALLING OR USING. By downloading, copying, installing or using the software you agree to this license. If you do not agree to this license, do not download, install, copy or use the software.

Intel License Agreement For Open Source Computer Vision Library

Redistribution and use in source and binary forms, with or without modification, are permitted provided that the following conditions are met:

• Redistribution’s of source code must retain the above copyright notice, this list of conditions and the following disclaimer.

• Redistribution’s in binary form must reproduce the above copyright notice, this list of conditions and the following disclaimer in the documentation and/or other materials provided with the distribution.

• The name of Intel Corporation may not be used to endorse or promote products derived from this software without specific prior written permission.

This software is provided by the copyright holders and contributors “as is” and any express or implied warranties, including, but not limited to, the implied warranties of merchantability and fitness for a particular purpose are disclaimed. In no event shall Intel or contributors be liable for any direct, indirect, incidental, special, exemplary, or consequential damages (including, but not limited to, procurement of substitute goods or services; loss of use, data, or profits; or business interruption) however caused and on any theory of liability, whether in contract, strict liability, or tort (including negligence or otherwise) arising in any way out of the use of this software, even if advised of the possibility of such damage.

All information provided related to future Intel products and plans is preliminary and subject to change at any time, without notice.

WHAT YOU CAN DO WITH THIS MACHINE

B Basic operations

After purchasing your machine, be sure to read this section first. This section provides details on the initial setup procedures as well as descriptions of this machine’s more useful functions.

Chapter 1 GETTING READY

To learn the operation of the principal parts and the screens

Chapter 2 STARTING TO EMBROIDER

To learn how to prepare for embroidering and basic embroidering operations

Page B-2

Page B-25

E Embroidering

This section provides instruction on editing embroidery patterns and recalling stored embroidery patterns.

Chapter 1 EMBROIDERY

Embroider artistically; by editing the built-in patterns you can easily create your own original designs.

Page E-2

A Appendix

This section provides important information for operating this machine.

Chapter 1 MAINTENANCE AND TROUBLESHOOTING

The various maintenance and troubleshooting procedures are described.

Page A-2

CONTENTS

INTRODUCTION .................................................. i

IMPORTANT SAFETY INSTRUCTIONS ................. i

TRADEMARKS ..................................................... iv

WHAT YOU CAN DO WITH THIS MACHINE ..... v

B Basic operations

Chapter 1 GETTING READY 2

Names of Machine Parts and Their Functions....... 2

Machine................................................................................. 2

Needle and presser foot section................................................... 3

Embroidery Unit..................................................................... 3

Operation buttons .................................................................. 4

Operation panel and operation keys....................................... 4

Included accessories .............................................................. 5

Optional accessories .............................................................. 6

Turning the Machine On/Off................................ 7

Turning on the machine ......................................................... 8

Turning off the machine ......................................................... 8

Select machine setting for the first time .................................. 8

LCD Operation ..................................................... 9

Viewing the LCD.................................................................... 9

Using the settings key........................................................... 10

Adjusting input sensitivity for operation keys........................ 12

Saving a settings screen image to USB flash drive ................. 13

Checking machine operating procedures.............................. 13

Winding/Installing the Bobbin............................ 14

Winding the bobbin ............................................................. 14

Installing the bobbin............................................................. 17

Upper Threading ................................................ 19

Threading the upper thread .................................................. 19

Threading the needle............................................................ 21

Threading the needle manually (without using the needle

threader)............................................................................... 22

Replacing the Needle.......................................... 23

Checking the needle............................................................. 23

Replacing the needle............................................................ 23

Chapter 2 STARTING TO EMBROIDER 25

Embroidery Step by Step..................................... 25

Attaching the Embroidery Unit........................... 26

Embroidery Attractive Finishes ........................... 28

Preparing the Fabric ........................................... 29

Attaching iron-on stabilizers (backing) to the fabric .............. 29

Hooping the fabric in the embroidery frame ......................... 30

Embroidering small fabrics or fabric edges ........................... 32

Attaching the Embroidery Frame ........................ 33

Selecting Embroidery Patterns............................ 35

Embroidery pattern types...................................................... 35

Selecting an embroidery pattern........................................... 35

Confirming the Pattern Position ......................... 36

Checking the pattern position............................................... 36

Previewing the selected pattern............................................ 36

Embroidering ...................................................... 37

Embroidering a pattern......................................................... 37

Changing the thread color display ........................................ 38

E Embroidering

Chapter 1 EMBROIDERY 2

Selecting Patterns................................................. 2

Selecting embroidery patterns/Brother “Exclusives”/floral

alphabet patterns................................................................... 2

Selecting character patterns ................................................... 2

Selecting frame patterns......................................................... 4

Editing Patterns .................................................... 5

Moving the pattern ................................................................ 6

Changing the size of the pattern............................................. 6

Rotating the pattern ............................................................... 7

Changing the thread color ..................................................... 7

Creating a horizontal mirror image ........................................ 7

Changing the density (alphabet character and frame

patterns only)......................................................................... 8

Deleting the pattern............................................................... 8

Displaying patterns in the screen magnification..................... 8

After editing........................................................................... 8

Editing Character Patterns ................................... 9

Changing the colors of alphabet character patterns................ 9

Switching between text written vertically and horizontally .... 9

Changing the font of entered characters............................... 10

Changing character spacing................................................. 10

Separating combined character patterns .............................. 10

Editing single characters ...................................................... 11

Changing the configuration of character patterns................. 12

Combining Patterns............................................ 13

Editing combined patterns ................................................... 13

Embroidering combined patterns ......................................... 14

Editing All Patterns............................................. 15

Moving the pattern .............................................................. 15

Rotating the pattern ............................................................. 15

Aligning the pattern and the needle ..................................... 15

Embroidering linked characters............................................ 16

Embroidery Applications .................................... 18

Sewing embroidery patterns which use appliqué ................. 18

Using a frame pattern to make an appliqué (1)..................... 20

Using a frame pattern to make an appliqué (2)..................... 21

Sewing split embroidery patterns ......................................... 22

Adjustments During the Embroidery Process ..... 23

If the bobbin runs out of thread............................................ 23

If the thread breaks during sewing ....................................... 24

Restarting from the beginning .............................................. 24

Resuming embroidery after turning off the power ................ 24

Making Embroidery Adjustments ....................... 26

Adjusting thread tension ...................................................... 26

Adjusting the bobbin case (with no color on the screw) ....... 27

Using the automatic thread cutting function

(END COLOR TRIM)............................................................ 28

Adjusting the embroidery speed........................................... 28

Changing the “Embroidery Frame Display”.......................... 28

Selecting/displaying patterns according to the embroidery

frame size............................................................................ 29

Changing the background colors of the embroidery

patterns................................................................................ 30

Specifying the size of pattern thumbnails............................. 30

Using the Memory Function............................... 31

Embroidery data precautions ............................................... 31

Saving embroidery patterns in the machine’s memory ......... 32

Saving embroidery patterns to USB flash drive..................... 33

Retrieving patterns from the machine’s memory .................. 34

Recalling from USB flash drive ............................................ 34

A Appendix

Chapter 1 MAINTENANCE AND

TROUBLESHOOTING 2

Care and Maintenance ......................................... 2

Restrictions on oiling ............................................................. 2

Precautions on storing the machine ....................................... 2

Cleaning the LCD Screen....................................................... 2

Cleaning the machine surface................................................ 2

Cleaning the race................................................................... 2

About the maintenance message............................................ 4

Touch panel is malfunctioning ............................................... 4

Operation beep...................................................................... 4

Replacing the embroidery foot............................................... 5

Troubleshooting ................................................... 6

List of symptoms .................................................................... 6

Error messages ..................................................................... 10

Upgrading your machine’s software using

USB flash drive ................................................... 12

Index .................................................................. 13

CONTENTS

vii

CONTENTS

viii

Basic

operations

This section provides details on the initial setup procedures as well as descriptions of this machine’s more useful functions.

Page number starts with “B” in this section.

Chapter1 GETTING READY....................................................... B-2

Chapter2 STARTING TO EMBROIDER................................. B-25

Names of Machine Parts and Their Functions

Chapter 1

GETTING READY

Names of Machine Parts and Their Functions

The names of the various parts of the machine and their functions are described below. Before using the machine, carefully read these descriptions to learn the names of the machine and their locations.

Machine

■ Front view

■ Right-side/rear view

1 Top cover

Open the top cover to place the spool of thread on the spool pin.

2 Thread guide plate

Pass the thread around the thread guide plate when threading the upper thread.

3 Bobbin winding thread guide and pretension disk

Pass the thread under this thread guide and around the pretension disk when winding the bobbin thread.

4 Spool cap

Use the spool cap to hold the spool of thread in place.

5 Spool pin

Place a spool of thread on the spool pin.

6 Bobbin winder

Use the bobbin winder when winding the bobbin.

7 LCD (liquid crystal display)

Settings for the selected pattern and error messages appear in the LCD. (page B-9)

8 Operation panel

From the operation panel, embroidery patterns can be selected and edited, and operations for using the machine can be selected. (page B-4)

9 Operation buttons

Use these buttons to operate the machine. (page B-4)

0 Embroidery unit

Attach embroidery unit to embroider. (page B-26)

A Thread cutter

Pass the threads through the thread cutter to cut them.

B Needle threader lever

Use the needle threader lever to thread the needle.

1 Handwheel

Turn the handwheel toward you (counterclockwise) to raise and lower the needle.

2 Handle

Carry the machine by its handle when transporting.

3 Presser foot lever

Raise and lower the presser foot lever to raise and lower the presser foot.

4 Main power switch

Use the main power switch to turn the machine on and off.

5 Power supply jack

Insert the plug on the power cord into the power supply jack.

6 Air vent

The air vent allows the air surrounding the motor to circulate. Do not cover the air vent while the machine is being used.

7 USB port (for a USB flash drive)

In order to import patterns from a USB flash drive, insert the USB flash drive directly into the USB port.

B-2

Names of Machine Parts and Their Functions

CAUTION

Needle and presser foot section

1 Needle bar thread guide

Pass the upper thread through the needle bar thread guide.

2 Needle plate 3 Needle plate cover

Remove the needle plate cover to clean the bobbin case and race.

4 Bobbin cover/bobbin case

Remove the bobbin cover and then insert the bobbin into the bobbin case.

5 Embroidery foot

The embroidery foot helps control fabric flexibility for better stitch consistency.

6 Embroidery foot screw

Use the embroidery foot screw to hold the embroidery foot in place.

Embroidery Unit

1 Frame-securing lever

Press the frame-securing lever to the left to attach or remove the embroidery frame. (page B-33)

2 Embroidery unit connector

Insert the embroidery unit connector into the connection port when attaching the embroidery unit. (page B-26)

3 Carriage

The carriage moves the embroidery frame automatically when embroidering. (page B-26)

4 Release button (located under the embroidery unit)

Press the release button to remove the embroidery unit. (page B-27)

• Before inserting or removing the embroidery unit, turn the main power to OFF.

GETTING READY

Basic operations B-3

Names of Machine Parts and Their Functions

CAUTION

Note

b c

Operation buttons

1 “Start/Stop” button

Press the “Start/Stop” button to start or stop embroidering. The button changes color according to the machine’s operation mode.

Green: The machine is ready to embroider or is

embroidering.

Red: The machine can not embroider.

Orange: The machine is winding the bobbin thread, or

the bobbin winder shaft is moved to the right side.

2 Needle position button

Press the needle position button to raise or lower the needle.

3 Thread cutter button

Press the thread cutter button after embroidering is stopped to cut both the upper and the bobbin threads.

• Do not press (Thread cutter button) after the threads have already been cut, otherwise the needle may break, the threads may become tangled or damage to the machine may occur.

Operation panel and operation keys

1 LCD (liquid crystal display) (touch panel)

Selected pattern settings and messages are displayed. Touch the keys displayed on the LCD to perform operations. For details, refer to “LCD Operation” on page B-9.

2 Previous page key

Displays the previous screen when there are items that are not displayed on the LCD.

3 Next page key

Displays the next screen when there are items that are not displayed on the LCD.

4 Help key

Press to get help on using the machine.

5 Settings key

Press to set the needle stop position, the buzzer sound, and more.

6 Embroidery key

Press this key to sew embroidery.

7 Back key

Press to return to the previous screen.

8 Presser foot/Needle exchange key

Press this key before changing the needle, the presser foot, etc. This key locks all key and button functions to prevent operation of the machine.

B-4

• The operation keys of this machine are capacitive touch sensors. Operate the keys by directly touching them with your finger. The response of the keys varies according to the user. The pressure exerted on the keys does not affect the response of the keys.

• Since the operation keys react differently depending on the user, adjust the setting for “Adjusting input sensitivity for operation keys” on page B-12.

• When using an electrostatic touch pen, make sure that its point is 8 mm or more. Do not use a touch pen with a thin point or a unique shape.

Names of Machine Parts and Their Functions

Included accessories

Included accessories may differ from the table below depending on the machine model you purchased. For more details on included accessories and their part codes of your machine, refer to the Quick Reference Guide.

1. 2. 3. 4. 5. 6.

Embroidery f oot “Q” (on machine)

7. 8. 9. 10. 11. 12.

Screwdriver (large) Screwdriver (small) Disc-shaped screwdriver Spool cap (large) Spool cap (medium)

13. 14. 15. 16. 17.

Thread spool insert (mini king thread spool)

18. 19. 20. 21. 22.

Accessory bag Dust cover Operation Manual Quick Reference Guide Embroidery Design Guide

Needle set 2/11 needle

Spool net Bobbin case

Bobbin (4) (One is on machine.)

(no color on the screw) (on machine)

Seam ripper Scissors Cleaning brush

(on machine)

Embroidery frame set (large) 18 cm (H) × 13 cm (W) (7 inches (H) × 5 inches (W))

Spool cap (small)

Poly 90 weight bobbin thread

GETTING READY

Basic operations B-5

Names of Machine Parts and Their Functions

Memo

Optional accessories

The following are available as optional accessories to be purchased separately. For more optional accessories and their part codes, refer to the Quick Reference Guide.

1. 2. 3.

Embroidery frame set (extra large (multi-position)) 30 cm (H) × 13 cm (W) (12 inches (H) × 5 inches (W))

4. 5.

Stabilizer material for embroidery

Water soluble stabilizer

• To obtain optional accessories or parts, contact your authorized Brother dealer.

• All specifications are correct at the time of printing. Please be aware that some specifications may change without notice.

• Visit your nearest authorized Brother dealer for a complete listing of optional accessories available for your machine.

• Always use accessories recommended for this machine.

Embroidery frame set (medium) 10 cm (H) × 10 cm (W) (4 inches (H) × 4 inches (W))

Embroidery frame set (small) 2 cm (H) × 6 cm (W) (1 inch (H) × 2-1/2 inches (W))

B-6

Turning the Machine On/Off

WARNING

CAUTION

Turning the Machine On/Off

• Use only regular household electricity for the power source. Using other power sources may result in fire,

electric shock, or damage to the machine.

• Make sure that the plugs on the power cord are firmly inserted into the electrical outlet and the power

cord receptacle on the machine. Otherwise, a fire or electric shock may result.

• Do not insert the plug on the power cord into an electrical outlet that is in poor condition.

• Turn the main power to OFF and remove the plug in the following circumstances:

When you are away from the machine After using the machine When the power fails during use When the machine does not operate correctly due to a bad connection or a disconnection During electrical storms

• Use only the power cord included with this machine.

• Do not use extension cords or multi-plug adapters with any other appliances plugged into them. Fire or

electric shock may result.

• Do not touch the plug with wet hands. Electric shock may result.

• When unplugging the machine, always turn the main power to OFF first. Always grasp the plug to remove

it from the electrical outlet. Pulling on the cord may damage the cord, or lead to fire or electric shock.

• Do not allow the power cord to be cut, damaged, modified, forcefully bent, pulled, twisted, or bundled.

Do not place heavy objects on the cord. Do not subject the cord to heat. These things may damage the cord, or cause fire or electric shock. If the cord or plug is damaged, take the machine to your authorized Brother dealer for repairs before continuing use.

• Unplug the power cord if the machine is not to be used for a long period of time. Otherwise, a fire may

result.

• When leaving the machine unattended, either the main switch of the machine should be turned to OFF or

the plug must be removed from the electrical outlet.

• When servicing the machine or when removing covers, the machine must be unplugged.

•(For U.S.A. only)

This appliance has a polarized plug (one blade wider than the other). To reduce the risk of electrical shock, this plug is intended to fit in a polarized electrical outlet only one way. If the plug does not fit fully in the electrical outlet, reverse the plug. If it still does not fit, contact a qualified electrician to install the proper electrical outlet. Do not modify the plug in any way.

GETTING READY

Basic operations B-7

Turning the Machine On/Off

Memo

Turning on the machine

Make sure that the machine is turned off (the main

power switch is set to “ ”), and then plug the power cord into the power supply jack on the right side of the machine.

Insert the plug of the power cord into a household

electrical outlet.

1 Power supply jack 2 Main power switch

Press the right side of the main power switch on the

right side of the machine to turn the machine on (set it to “I”).

Turning off the machine

When you are finished using the machine, turn it off. In addition, before transporting the machine to another location, be sure to turn it off.

Make sure that the machine is not embroidering.

Press the main power switch on the right side of the

machine in the direction of the “ ” symbol to turn the machine off.

Select machine setting for the first time

When you first turn on the machine, select the language of your choice. Follow the procedure below when the settings screen appears automatically.

Press and to select your choice of language.

→ The light, LCD and the “Start/Stop” button light up

when the machine is turned on.

• When the machine is turned on, the machine will make a sound when it moves; this is not a malfunction.

• If the machine is turned off in the middle of embroidering, the operation will resume after turning the power on again.

When the machine is turned on, the opening movie is

played. Press anywhere on the screen.

Press .

B-8

LCD Operation

Viewing the LCD

An opening movie may be displayed when the power is turned on. When the opening movie is displayed, the screen will be displayed if you touch the LCD with your finger. Press a key with your finger to select the embroidery pattern, to select a machine function, or to select an operation indicated on the key.

The screen below appears after the embroidery carriage moves to its initial position.

GETTING READY

1 Embroidery patterns 2 Brother “Exclusives” 3 Floral alphabet patterns 4 Character patterns 5 Frame patterns 6 Press this key to position the embroidery unit for

storage

7 Patterns saved in the machine's memory 8 Patterns saved in USB flash drive

Basic operations B-9

LCD Operation

Using the settings key

Press to change the default machine settings (needle stop position, embroidery speed, opening display, etc.). Press , after you changed necessary settings.

■ Embroidery settings

Page 1 Page 2 Page 3

1 Select the embroidery frame to be used. 2 Select the centerpoint marker and grid that are displayed. For details, refer to “Changing the “Embroidery Frame Display”” in the

“Embroidering” section.

3 When set to “ON”, the embroidery pattern can be selected according to the embroidery frame size that you have selected in

4 Change the thread color display on the “Embroidery” screen; thread number, color name. (page B-38). 5 When the thread number “#123” is selected, select from six thread brands. (page B-38). 6 Adjust the maximum embroidery speed setting. For details, refer to “Adjusting the embroidery speed” in the “Embroidering”

7 Change the display units (mm/inch). 8 Adjust the upper thread tension for embroidering. For details, refer to “Adjusting thread tension” in the “Embroidering” section. 9 Press to specify the size of pattern thumbnails. For details, refer to “Specifying the size of pattern thumbnails” in the

0 Change the color of the background for the embroidery display area. For details, refer to “Changing the background colors of the

A Change the color of the background for the thumbnail area. For details, refer to “Changing the background colors of the

1. For details, refer to “Selecting/displaying patterns according to the embroidery frame size” in the “Embroidering”

number section.

section.

“Embroidering” section.

embroidery patterns” in the “Embroidering” section.

B-10

LCD Operation

Memo

■ General settings

Page 4 Page 5 Page 6

B Select the needle stop position (the needle position for when the machine is not being operated) to be up or down. C Select whether to hear the beep operation sound. For details, refer to “Operation beep” in the “Appendix” section. D Select whether to display the opening screen when the machine is turned on. E Select the display language. (page B-12) F Select whether to turn on the light for the needle area and work area. G Select the level of the input sensitivity for operation keys. (page B-12) H Display the service count which is a reminder to take your machine in for regular servicing. (Contact your authorized Brother

dealer for details.)

I Display the total number of stitches sewn on this machine. J The “No.” is the internal machine number for your machine. K Display the program version of the LCD panel.

GETTING READY

• The latest version of software is installed in your machine. Check with your local authorized Brother dealer or at “ http://support.brother.com/ USB flash drive” in the “Appendix” section.

• Press to save the current settings screen image to USB flash drive. (page B-13)

” for available updates. For details, refer to “Upgrading your machine’s software using

Basic operations B-11

LCD Operation

Note

■ Choosing the display language

Press .

Display page 4.

Use and to choose the display language.

1 Display language

Press to return to the original screen.

Adjusting input sensitivity for operation keys

You can adjust the sensitivity of the operation keys to five levels. Display the settings screen to set desired level.

Adjust the “Input Sensitivity” by pressing / .

• The higher the setting, the more sensitive the keys will be. The default setting is “3”.

• We recommend selecting the highest setting if an electrostatic touch pen is being used.

• While adjusting the input sensitivity, press to check the sensitivity. When the key responds, the setting value indicating the sensitivity blinks.

1 Operation keys

Press to display the settings screen.

Display page 5 by pressing / .

Press “Start”.

→ The adjusting screen is displayed.

Press to return to previous screen.

■ If the machine does not respond when an operation key is pressed

Turn machine off, then hold down (Thread cutter button) and turn on the machine to reset the setting. Display the settings screen, and then adjust the setting

again.

B-12

Saving a settings screen image to USB flash

4321

5 6 7

drive

An image of the settings screen can be saved as a BMP file.

Insert the USB flash drive into the USB port on the

right side of the machine.

1 USB port 2 USB flash drive

Press .

→ The settings screen appears. Select the settings screen

page, make the changes that you want, and then save the screen image.

Press .

→ The image file will be saved to the USB flash drive.

Remove the USB flash drive, and then for future

reference, check the saved image using a computer.

• The files for settings screen images are saved with the name “S######.bmp” in a folder labeled “bPocket”.

LCD Operation

Press the item to be displayed.

1 Upper threading 2 Bobbin winding 3 Bobbin installation 4 Needle replacement 5 Embroidery unit attachment 6 Embroidery frame attachment 7 Embroidery foot attachment

→ The first screen describing the procedure for the

selected topic appears.

• Pressing , returns you to the item selection screen.

Press to switch to the next page.

If you press , you return to the previous page.

After you have finished viewing, press two times.

GETTING READY

Checking machine operating procedures

Turn on the machine.

→ The LCD comes on.

Press anywhere on the LCD screen.

Press on the operation panel.

→ The machine help screen appears.

Basic operations B-13

Winding/Installing the Bobbin

CAUTION

Memo

Winding/Installing the Bobbin

• Only use the Bobbin (part code: SA156, SFB: XA5539-151) designed specifically for this machine. Use of any other bobbin may result in injuries or damage to the machine.

• The included bobbin was designed specifically for this machine. If bobbins from other models are used, the machine will not operate correctly. Use only the included bobbin or bobbins of the same type (part code: SA156, SFB: XA5539-151).

SA156 is Class15 type bobbin.

Open the top cover.

Place the bobbin on the bobbin winder shaft so that the

spring on the shaft fits into the notch in the bobbin Press down on the bobbin until it snaps into place.

1 Notch 2 Bobbin winder shaft spring

Slide the bobbin winder in the direction of the arrow

until it snaps into place.

* Made of plastic

1 This model 2 Other models 3 11.5 mm (approx. 7/16 inch)

Winding the bobbin

This section describes how to wind thread onto a bobbin.

• When winding bobbin for embroidery be sure to

use the recommended bobbin thread for this machine.

• The “Start/Stop” button lights up in orange.

Remove the spool cap that is inserted onto the spool

pin.

1 Spool pin 2 Spool cap

B-14

Place the spool of thread for the bobbin onto the spool

CAUTION

Memo

pin.

Slide the spool onto the pin so that the spool is horizontal and the thread unwinds to the front at the bottom.

Winding/Installing the Bobbin

• When using the spool as shown below, use the small spool cap, and leave a small space between the cap and the spool.

• If the spool is not positioned so that the thread unwinds correctly, the thread may become tangled around the spool pin.

Slide the spool cap onto the spool pin.

Slide the spool cap as far as possible to the right, as shown, with the rounded side on the left.

• If the spool or the spool cap is not installed correctly, the thread may become tangled around the spool pin, causing the needle to break.

• Three spool cap sizes are available, allowing you to choose a spool cap that best fits the size of spool being used. If the spool cap is too small for the spool being used, the thread may catch on the slit in the spool or the machine may be damaged. When using mini king thread spool, use the thread spool insert (mini king thread spool). For details on thread spool insert (mini king thread spool), refer to “Memo” on page B-15.

1 Spool cap (small) 2 Spool (cross-wound thread) 3 Space

• When using thread that winds off quickly, such as metallic thread, place the spool net over the spool before placing the spool of thread onto the spool pin. If the spool net is too long, fold it to fit the size of the spool.

1 Spool net 2 Spool 3 Spool cap 4 Spool pin

• If a spool of thread whose core is 12 mm (1/2 inch) in diameter and 75 mm (3 inches) high is inserted onto the spool pin, use the thread spool insert (mini king thread spool).

GETTING READY

1 Thread spool insert (mini king thread spool) 2 12 mm (1/2 inch) 3 75 mm (3 inches)

Basic operations B-15

Winding/Installing the Bobbin

Note

CAUTION

While holding the thread near the spool with your right

hand, as shown, pull the thread with your left hand, and then pass the thread behind the thread guide cover and to the front.

1 Thread guide cover

Pass the thread under the thread guide plate, and then

pull it to the right.

While holding the thread with your left hand, wind the

thread that was pulled out clockwise around the bobbin five or six times with your right hand.

• Make sure that the thread between the spool and the bobbin is pulled tight.

• Be sure to wind the thread clockwise around the bobbin, otherwise the thread will become wrapped around the bobbin winder shaft.

Pass the end of the thread through the guide slit in the

bobbin winder seat, and then pull the thread to the right to cut it.

1 Thread guide plate

Pass the thread under the hook on the thread guide,

and then wind it counterclockwise under the pretension disk.

1 Thread guide 2 Pretension disk 3 Pull it in as far as possible

• Make sure that the thread passes under the pretension disk.

1 Guide slit in bobbin winder seat

(with built-in cutter)

• Be sure to cut the thread as described. If the bobbin is wound without cutting the thread using the cutter built into the slit in the bobbin winder seat, the thread may become tangled in the bobbin or the needle may bend or break when the bobbin thread starts to run out.

Turn on the machine.

Press the “Start/Stop” button once to start winding the

bobbin.

1 “Start/Stop” button

When the bobbin winding becomes slow, press the

“Start/Stop” button once to stop the machine.

B-16

• When the bobbin winding becomes slow, stop the machine, otherwise the machine may be damaged.

Winding/Installing the Bobbin

Memo

CAUTION

Use scissors to cut the end of the thread wound around

the bobbin.

Slide the bobbin winder shaft to the left, and then

remove the bobbin from the shaft.

• If the bobbin winder shaft is set to the right side, the needle will not move. (Embroidering is impossible.)

Remove the spool for the bobbin thread from the spool

pin.

Press (Needle position button) once or twice to

raise the needle.

Press .

→ The screen changes, and all keys and operation

buttons are locked (except ).

Raise the presser foot lever.

Slide the bobbin cover latch to the right.

1 Bobbin cover 2 Latch

GETTING READY

• When the machine is started or the handwheel is turned after winding the bobbin, the machine will make a clicking sound; this is not a malfunction.

Installing the bobbin

Install the bobbin wound with thread. You can begin embroidering immediately without pulling up the bobbin thread by simply inserting the bobbin in the bobbin case and guiding the thread through the slit in the needle plate cover.

• Use a bobbin that has been correctly wound with thread, otherwise the needle may break or the thread tension will be incorrect.

Remove the bobbin cover.

Hold the bobbin with your right hand with the thread

unwinding to the left, and hold the end of the thread with your left hand. Then, with your right hand, place the bobbin in the bobbin case.

• Before inserting or changing the bobbin, be sure to press on the operation panel to

lock all keys and buttons, otherwise injuries may occur if the “Start/Stop” button or any other button is pressed and the machine starts.

Basic operations B-17

Winding/Installing the Bobbin

CAUTION

Memo

Note

Lightly hold down the bobbin with your right hand

(1), and then guide the end of the thread around the tab of the needle plate cover with your left hand (2).

1 Tab

• Be sure to hold down the bobbin with your finger and unwind the bobbin thread correctly, otherwise the thread may break or the thread tension will be incorrect.

• The order that the bobbin thread should be

passed through the bobbin case is indicated by marks around the bobbin case. Be sure to thread the machine as indicated.

While lightly holding down the bobbin with your right

hand (1), continue guiding the thread through the slit with your left hand (2). Then, cut the thread with the cutter (3).

• If the thread is not correctly inserted through the tension-adjusting spring of the bobbin case, it may cause incorrect thread tension.

While lightly holding down the bobbin with your right

hand (1), guide the thread through the slit in the needle plate cover (2) and lightly pull it with your left hand (3).

• The thread enters the tension spring of the bobbin case.

1 Tension-adjusting spring

Reattach the bobbin cover.

Insert the tab in the lower-left corner of the bobbin cover, and then lightly press down on the right side.

→ The bobbin threading is finished.

Next, thread the upper thread. Continue with the procedure in “Upper Threading” on page B-19.

Press to unlock all keys and buttons.

B-18

Upper Threading

CAUTION

Note

• Three spool cap sizes are available, allowing you to choose a spool cap that best fits the size of spool being used. If the spool cap is too small for the spool being used, the thread may catch on the slit in the spool or the needle may break. When using mini king thread spool, use the thread spool insert (mini king thread spool). For more information regarding the choice of spool caps for your thread choice, see page B-15.

Upper Threading

Raise the presser foot lever to raise the presser foot.

1 Presser foot lever

→ The upper thread shutter opens so the machine can

be threaded.

GETTING READY

• When threading the upper thread, carefully follow the instructions. If the upper threading is not correct, the thread may become tangled or the needle may bend or break.

Threading the upper thread

1 Shutter

• If the presser foot is not raised, the machine cannot be threaded.

Press (Needle position button) once or twice to

raise the needle.

1 Needle position button

→ The needle is correctly raised when the mark on the

handwheel is at the top, as shown below. Check the

handwheel and, if this mark is not at this position, press (Needle position button) until it is.

→ When threading the upper thread, carefully follow

the instructions.

Turn on the machine.

1 Mark on handwheel

Basic operations B-19

Upper Threading

CAUTION

Note

Remove the spool cap that is inserted onto the spool

pin.

1 Spool pin 2 Spool cap

Place the spool of thread onto the spool pin.

Slide the spool onto the pin so that the spool is horizontal and the thread unwinds to the front at the bottom.

While holding the thread lightly with your right hand,

pass the thread under the thread guide plate, and then pull it up.

1 Thread guide plate

Pass the thread through the thread channel in the order

shown below.

• If the spool or the spool cap is not positioned correctly, the thread may become tangled around the spool pin or the needle may break.

Slide the spool cap onto the spool pin.

Slide the spool cap as far as possible to the right, as shown, with the rounded side on the left.

While holding the thread lightly with your right hand,

pull the thread with your left hand, and then pass the thread behind the thread guide cover and to the front.

1 Thread guide cover

1 Shutter

• If the presser foot has been lowered and the shutter is closed, the machine cannot be threaded. Be sure to raise the presser foot to open the shutter before threading the machine. In addition, before removing the upper thread, be sure to raise the presser foot to open the shutter.

• This machine is equipped with a window that allows you to check the position of the take-up lever. Look through this window and check that the thread is correctly fed through the take-up lever.

Press .

→ The screen changes, and all keys and operation

buttons are locked (except ).

B-20

+ 70 hidden pages