HL-4040CN
HL-4050CDN
Laser Printer
Before you can use the printer, you must set up the hardware and install the driver. Please
read this ‘Quick Setup Guide’ for proper set up and installation instructions.
STEP 1
Setting Up the Machine
STEP 2
Installing the Printer Driver
Setup is Complete!
Quick Setup Guide
How to use the printer, see the User’s Guide in the CD-ROM.
Keep this ‘Quick Setup Guide’ and the supplied CD-ROM in a convenient place for quick and
easy reference at all times.
1
Symbols used in this guide
Warning
Warnings tell you what to do
to prevent possible personal
injury.
Improper Setup
Improper Setup icons alert
you to devices and
operations that are not
compatible with the printer.
Electrical Hazard
Electrical Hazard icons alert
you to a possible electrical
shock.
Note
Notes tell you how you should
respond to a situation that
may arise or give tips about
how the current operation
works with other features.
Hot Surface
Hot Surface icons warn you
not to touch machine parts
that are hot.
User's Guide
Network User's Guide
Indicates reference to the
User's Guide or Network
User's Guide which is on the
CD-ROM we have supplied.
Caution
Cautions specify procedures
you must follow or avoid to
prevent possible damage to
the printer or other objects.
Table of Contents
Safety Precautions ....................................................................................................................................... 4
To Use the Printer Safely ........................................................................................................................ 4
Regulations ............................................................................................................................................. 5
Getting Started
What is in the box?....................................................................................................................................... 7
Control panel................................................................................................................................................ 8
Supplied CD-ROM ....................................................................................................................................... 9
STEP 1— Setting Up the Machine
Put the CD-ROM into the CD-ROM drive................................................................................................... 10
Removing the packing materials from the printer....................................................................................... 11
Installing the toner cartridges ..................................................................................................................... 12
Loading paper in the paper tray ................................................................................................................. 12
Printing a test page .................................................................................................................................... 13
Setting your language on the control panel................................................................................................ 14
STEP 2— Installing the Printer Driver
Windows
For USB interface cable users .................................................................................................................. 16
For parallel interface cable users .............................................................................................................. 17
For network interface cable users ............................................................................................................. 18
For Peer-to-Peer network printer users ............................................................................................... 18
For shared network printer users ......................................................................................................... 19
Macintosh
For USB interface cable users .................................................................................................................. 21
For network interface cable users ............................................................................................................. 22
®
®
Other Information
Shipment of the printer ............................................................................................................................... 24
Troubleshooting
Chapter 7 of the User’s Guide on the CD-ROM
3
Safety Precautions
To Use the Printer Safely
Warning
There are high voltage electrodes inside the printer. Before you clean the inside of the printer, make sure that
you have turned off the power switch and unplugged the printer from the AC power outlet.
DO NOT handle the plug with wet hands. Doing this might cause an electrical shock.
The fuser unit becomes extremely hot during operation. Wait until it has cooled down sufficiently before
replacing consumable items. DO NOT remove or damage the caution labels located on or around the fuser.
DO NOT use flammable substances or any type of spray to clean the inside or outside of the machine. Doing
this may cause a fire or electrical shock. Refer to the User's Guide for how to clean the machine.
DO NOT use a vacuum cleaner to clean up scattered toner. Doing this might cause the toner dust to ignite
inside the vacuum cleaner, potentially starting a fire. Please carefully clean the toner dust with a dry, lint-free
cloth and dispose of it according to local regulations.
If the printer becomes hot, blows smoke, or generates obscure odor, immediately turn off the power switch and
unplug the printer from the AC power outlet. Call your Brother dealer or Brother Customer Service.
4
Safety Precautions
If metal objects, water or other liquids get inside the printer, immediately turn off the power switch and unplug
the printer from the AC power outlet. Call your Brother dealer or Brother Customer Service.
This printer is heavy and weighs approximately 64.2 lb. (29.1 kg). To prevent injuries use at least two people
to lift the printer. Be careful not to pinch your fingers when you put the printer back down.
Regulations
Important
A shielded interface cable should be used in order to
ensure compliance with the limits for a Class B digital
device.
Changes or modifications not expressly approved by
Brother Industries, Ltd. could void the user's authority
to operate the equipment.
Radio interference (220-240 volt model only)
This printer follows EN55022 (CISPR Publication
22)/Class B.
Before you use this product, make sure that you use
one of the following interface cables.
1 A shielded parallel interface cable with twisted-pair
conductors and that it is marked “IEEE 1284
compliant”.
2 A USB cable.
The cable must not be more than 2 meters long.
EC Declaration of Conformity
5
International ENERGY STAR® Compliance
Statement
The purpose of the International ENERGY STAR
®
Program is to promote the development and
popularization of energy-efficient office equipment.
As an ENERGY STAR
®
Partner, Brother Industries,
Ltd. has determined that this product meets the
ENERGY STAR
®
guidelines for energy efficiency.
IEC 60825-1 specification (220 to 240 volt model
only)
This printer is a Class 1 laser product as defined in
IEC 60825-1+A2: 2001 specifications. The label
shown below is attached in countries where it is
needed.
IMPORTANT - For Your Safety
To ensure safe operation, the supplied three-pin plug
must be inserted only into a standard three-pin power
outlet that is properly grounded through the normal
household wiring.
Extension cords used with this printer must be threepin plug type and correctly wired to provide proper
grounding. Incorrectly wired extension cords may
cause personal injury and equipment damage.
The fact that the equipment operates satisfactorily
does not imply that the power is grounded and that
the installation is completely safe. For your safety, if
in any doubt about the effective grounding of the
power, call a qualified electrician.
This product should be connected to an AC power
source within the range indicated on the rating label.
DO NOT connect it to a DC power source. If you are
not sure, contact a qualified electrician.
Disconnect device
You must install this printer near a power outlet that is
easily accessible. In case of an emergency, you must
disconnect the power cord from the power outlet to
shut off the power completely.
CLASS 1 LASER PRODUCT
APPAREIL À LASER DE CLASSE 1
LASER KLASSE 1 PRODUKT
This printer has a Class 3B laser diode which
produces invisible laser radiation in the laser unit. You
should not open the laser unit under any
circumstances.
Caution
Use of controls or adjustments or performance of
procedures other than those specified herein may
result in hazardous radiation exposure.
Internal laser radiation
Maximum radiation power: 25 mW
Wave length: 780 - 800 nm
Laser class: Class 3B
Caution for LAN connection
Connect this product to a LAN connection that is not
subjected to over voltages.
Warning - This printer must be earthed.
The wires in the mains lead are coloured in line with
the following code:
Green and Yellow: Earth
Blue: Neutral
Brown: Live
If in any doubt, call a qualified electrician.
6
Getting Started
1
1
Carton components may vary from one country to another.
Save all packing materials and the printer carton in case for any reason you must ship your printer.
What is in the box?
1
2
3
4
5
8 7
6
9
1 Front cover release button
2 Control panel
1
3 USB direct interface
4Front cover
5 Paper tray
6 Power switch
7 Face-down output tray
8 Face-down output tray support flap (Support flap)
9 Multi -purpose tray (MP tray)
1
You can adjust the angle of the LCD display by tilting it up or down.
CD-ROM
(including User’s
Guide)
Quick Setup Guide
AC power cord
Belt unit
(pre-installed)
Waste toner box
(pre-installed)
Insertion sheet and
Toner cartridges
(Black, Cyan, Magenta and Yellow)
Drum unit
Plastic bag for
repacking
(pre-installed)
The interface cable is not a standard accessory. Buy the appropriate cable for the interface you are going to use.
USB cable
Do not use a USB interface cable that is longer than 6 feet (2.0 meters).
Do not connect the USB cable to a non-powered hub or a Macintosh
®
keyboard.
Make sure that you connect it to the USB connector of your computer.
Parallel cable (For HL-4050CDN users)
Do not use a parallel interface cable that is longer than 6 feet (2.0 meters).
Use a shielded interface cable that is IEEE 1284-compliant.
Network cable
Use a straight-through Category5 (or greater) twisted-pair cable for 10BASE-T or 100BASE-TX Fast Ethernet
Network.
7
Getting Started
2
Control panel
1 Menu buttons
+
7
Scroll backward through menus and the available options.
-
Scroll forward through menus and the available options.
6
OK
Choose the control panel menu.
Select the chosen menus and settings.
Back
Go back one level in the menu structure.
2 Reprint button
1
Choose the reprint menu.
3 Go button
Clear error messages.
Pause and continue printing.
2
4 Cancel button
Stop and cancel the print operation in progress.
5
Exit from a menu (control panel menu, reprint menu or Direct
Print menu)
3
5 Direct Print LED: Blue
On
4
USB flash memory is inserted into the USB direct interface.
Off
USB flash memory is not inserted into the USB direct
interface.
Direct Print button
Switch to Direct Print mode when USB flash memory is
inserted into the USB direct interface.
6 LCD back light
Off
The printer is off or in sleep status.
Green (General)
Ready to print / Printing / Warming up
Red (Error)
There is a problem with the printer.
Orange (Setting)
Choose a menu (control panel menu, reprint menu or Direct Print menu) or Pause
LCD messages
The message on the LCD shows the current printer status during normal operation.
The o marks indicate the status of the toner in the toner cartridges. When the o mark blinks (n), the indicated
toner is nearly empty. When toner becomes empty, the o indicator disappears completely.
7 Data LED: Yellow
On
Data is in the printer memory.
Blinking
Receiving / processing data
Off
No remaining data in the memory.
For the control panel details, see Chapter 4 of the User’s Guide on the CD-ROM.
8
Getting Started
3
Supplied CD-ROM
You can find a variety of information on the CD-ROM.
Windows
®
Initial Setup
Instructional movie for printer setup.
Install Printer Driver
Install the printer driver.
Install Other Drivers or Utilities
Install optional drivers, utilities and Network
management tools.
Macintosh
®
Documentation
View the Printer User’s Guide and Network User's
Guide in HTML format.
You can also view the manuals in PDF format by
accessing the Brother Solutions Center.
The User’s Guide and Network User’s Guide in HTML
format will be installed automatically when you install
the driver. Click the Start button, All Programs
1
,
your printer (Brother HL-4050CDN), and then User’s
Guide. If you do not want to install the User’s Guide,
choose Custom setup from Install Printer Driver,
and uncheck User’s Guides in HTML format when
you install the driver.
1
Programs for Windows® 2000 users
On-Line Registration
Register your product on-line.
Brother Solutions Center
The Brother Solutions Center
(http://solutions.brother.com
) is a one-stop resource
for all your printer support needs. Download the latest
drivers and utilities for your printers, read FAQs and
troubleshooting tips, or learn about printer solutions.
Supplies Information
Visit our web site for original/genuine Brother supplies
at http://www.brother.com/original/
Initial Setup
Instructional movie for printer setup.
Install Printer Driver
Install the printer driver.
Documentation
View the Printer User’s Guide and Network User's
Guide in HTML format.
You can also view the User’s Guide in PDF format by
accessing the Brother Solutions Center.
On-Line Registration
Register your product on-line.
Brother Solutions Center
The Brother Solutions Center
(http://solutions.brother.com
) is a one-stop resource
for all your printer support needs. Download the latest
drivers and utilities for your printers, read FAQs and
troubleshooting tips, or learn about printer solutions.
Supplies Information
Visit our web site for original/genuine Brother supplies
at http://www.brother.com/original/
Note
For visually impaired users, we have prepared an HTML file on the supplied
CD-ROM: readme.html. This file can be read by Screen Reader ‘text-tospeech’ software.
9
STEP 1
1
1 Put the CD-ROM into the CD-ROM drive
Setting Up the Machine
For Windows® users
Improper Setup
DO NOT connect the interface cable.
Connecting the interface cable is done when
installing the driver.
1 Turn on your computer. (You must be logged
on with Administrator rights.) Put the supplied
CD-ROM into your CD-ROM drive. The
opening screen will appear automatically.
Choose your printer model and the language.
2 Click Initial Setup on the menu screen.
For Macintosh® users
Improper Setup
DO NOT connect the interface cable.
Connecting the interface cable is done when
installing the driver.
1 Turn on your Macintosh
ROM into your CD-ROM drive, and then
double-click the HL4040_4050 icon on your
desktop. Double-click the Start Here icon.
Follow the on-screen instructions.
®
. Put the supplied CD-
3 You can view the initial setup instructions and
follow along with the steps on the next page.
2 Click Initial Setup on the menu screen.
3 You can view the initial setup instructions and
follow along with the steps on the next page.
10
2 Removing the packing
materials from the printer
Important
Save all packing material and the carton in
case you have to ship your machine.
Improper Setup
DO NOT plug in the AC power cord yet.
1 Press the front cover release button and open
the front cover.
Setting Up the Machine
3 Hold the green handle of the drum unit. Lift the
drum unit up and then pull it out until it stops.
2 Remove the 4 pieces of orange packing
material as shown in the illustration below.
4 Remove the orange packing material as shown
in the illustration below.
11
STEP 1
3 Installing the toner
1 Unpack the toner cartridges and rock each
2 Remove the protective cover.
Setting Up the Machine
cartridges
toner cartridge 5 to 6 times.
5 Put the drum unit back into the printer.
6 Close the front cover of the printer.
3 Hold the handle of the toner cartridge and slide
it into the drum unit. Make sure that you match
the toner cartridge color to the same color label
on the drum unit, and make sure that you fold
down the toner cartridge handle (1) once the
toner cartridge is in place.
1
1
1
2
3
4
4 Loading paper in the paper
1 Pull the paper tray completely out of the printer.
tray
2 While pressing the green paper-guide release
lever (1), slide the paper guides to fit the paper
size. Make sure that the guides are firmly in the
slots.
1 C — Cyan
2 M — Magenta
3 Y — Yellow
4 K — Black
4 Repeat steps 1 through 3 for the remaining
toner cartridges.
12
1
Setting Up the Machine
3 Fan the stack of paper well to avoid paper jams
and misfeeds.
4 Put paper in the paper tray. Make sure that the
paper is flat in the tray and below the maximum
paper mark.
1 Lift the LCD display and adjust it for the best
viewing angle.
2 Unfold the support flap.
5 Put the paper tray firmly back into the printer.
Mak e sure th a t it is co mplete l y insert ed into t h e
printer.
5 Printing a test page
Improper Setup
DO NOT connect the interface cable yet.
3 Make sure that the printer power switch is off.
Remove the label covering the AC power inlet.
4 Connect the AC power cord to the printer.
13
STEP 1
5 Plug the AC power cord into an AC power
6 After the printer has finished warming up, the
Setting Up the Machine
outlet. Turn on the printer power switch.
LCD shows Ready.
6 Setting your language on the
control panel
7 Press Go. The printer prints a test page. Check
that the test page has printed correctly.
1 Press the + or – button until the LCD shows
General Setup.
Press OK.
Select ab or OK
General Setup
2 Press OK again.
General Setup
Local Language
3 Press the + or – button to choose your
language. Press OK to accept.
Local Language
English
Note
• If you press Reprint, the printer prints a duplex
test page. (For HL-4050CDN)
• This function will not be available after the first
print job you send from your computer.
14
STEP 2
Follow the instructions on this page for your operating system and interface.
For the latest drivers, documentation, and to find the best solution for your problem, access the Brother Solution Center
directly from the CD-ROM / Driver or visit http://solutions.brother.com.
Installing the Printer Driver
Windows
For USB interface cable users....................................................................................... 16
For parallel interface cable users.................................................................................. 17
For network interface cable users ................................................................................ 18
Macintosh
For USB interface cable users....................................................................................... 21
®
For Peer-to-Peer network printer users............................................................................................. 18
For shared network printer users ...................................................................................................... 19
®
For network interface cable users ................................................................................ 22
The screens for Windows® in this Quick Setup Guide are based on Windows® XP.
The screens for Mac OS
®
X in this Quick Setup Guide are based on Mac OS® X 10.4.
15
STEP 2
1
1
®
USB
Windows
Note
If the Found New Hardware Wizard appears on
your computer, click Cancel.
Installing the driver and connecting the printer to
your computer
Installing the Printer Driver
For USB interface cable users
Windows
• If you want to install the PS driver (Brother’s
BR-Script Driver), choose Custom setup and
then follow the on-screen instructions. When the
Select Components screen appears, check
PS(PostScript Emulation) Driver, and then
continue following the on-screen instructions.
4 When the License Agreement window
appears, click Yes if you agree to the License
Agreement.
5 When this screen appears, make sure the
printer power switch is on.
Connect the USB interface cable to your
computer, and then connect it to the printer.
Click Next.
®
1 Make sure the USB interface cable is NOT
connected to the printer, and then begin
installing the driver. If you have already
connected the cable, remove it.
2 Click Install Printer Driver on the menu
screen.
3 Click USB cable users.
Note
• For Windows Vista™, when the User Account
Control screen appears, click Continue.
6 Click Finish.
Note
• If you want to register your product on-line, check
On-Line Registration.
• If you do not want to set your printer as Default
printer, uncheck Set as Default Printer.
Setup is now complete.
16
Installing the Printer Driver
Windows
®
2
For parallel interface cable users
Note
If the Found New Hardware Wizard appears on
your computer, click Cancel.
Installing the driver and connecting the printer to
your computer
1 Click Install Printer Driver on the menu
screen.
• If you do not want to set your printer as Default
printer, uncheck Set as Default Printer.
5 Turn off the printer power switch.
6 Connect the parallel interface cable to your
computer, and then connect it to your printer.
7 Turn on the printer power switch.
®
Parallel
Windows
2 Click Parallel cable users.
Note
• For Windows Vista™, when the User Account
Control screen appears, click Continue.
• If you want to install the PS driver (Brother’s
BR-Script Driver), choose Custom setup and
then follow the on-screen instructions. When the
Select Components screen appears, check
PS(PostScript Emulation) Driver, and then
continue following the on-screen instructions.
3 When the License Agreement window
appears, click Yes if you agree to the License
Agreement.
Setup is now complete.
4 Click Finish.
Note
• If you want to register your product on-line, check
On-Line Registration.
17
STEP 2
Installing the Printer Driver
Windows
®
3
For network interface cable users
For Peer-to-Peer network printer users
Note
R
1
Macintosh
Windows
TCP/IP
®
Windows
1 Router
2Network printer
Network
R
2
TCP/IP
• If you are going to connect the printer to your
network, we recommend that you contact your
system administrator prior to installation or see the
Network User’s Guide on the CD-ROM.
• If you are using Personal Firewall software (e.g.
Windows Firewall), disable it. Once you are sure
that you can print, restart your Personal Firewall
software.
Connecting the printer to your network and
installing the driver
• If you want to install the PS driver (Brother’s
BR-Script Driver), choose Custom setup and
then follow the on-screen instructions. When the
Select Components screen appears, check
PS(PostScript Emulation) Driver, and then
continue following the on-screen instructions.
3 Turn off the printer power switch.
4 Connect the network interface cable to the
printer, and then connect it to a free port on
your hub.
5 Turn on the printer power switch.
1 Click Install Printer Driver on the menu
screen.
2 Click Network cable users.
Note
• For Windows Vista™, when the User Account
Control screen appears, click Continue.
6 When the License Agreement window
appears, click Yes if you agree to the License
Agreement.
7 Choose Brother Peer-to-Peer Network
Printer, and then click Next.
18
Installing the Printer Driver
Windows
®
8 Choose Search the network for devices and
choose from a list of discovered devices
(Recommended). Or enter your printer's IP
address or its node name. Click Next.
Note
Contact your administrator if you do not know the
printer's IP address or node name.
For shared network printer users
9 Choose your printer, and then click Next.
10 Click Finish.
Note
• If you want to register your product on-line, check
On-Line Registration.
• If you do not want to set your printer as Default
printer, uncheck Set as Default Printer.
®
Network
Windows
Windows
Windows
1 Network Shared
2 Also known as “Server” or “Printer server”
3 Printer
4 TCP/IP, USB or Parallel
R
TCP/IP
R
Windows
2
R
4
3
1
Note
If you are going to connect to a shared printer on
your network, we recommend that you ask your
system administrator about the queue or share
name for the printer prior to installation.
Installing the driver and choosing the correct
printer queue or share name
1 Click Install Printer Driver on the menu
screen.
2 Click Network cable users.
Note
• For Windows Vista™, when the User Account
Control screen appears, click Continue.
• If you want to install the PS driver (Brother’s
BR-Script Driver), choose Custom setup and
then follow the on-screen instructions. When the
Select Components screen appears, check
PS(PostScript Emulation) Driver, and then
continue following the on-screen instructions.
19
STEP 2
3 When the License Agreement window
4 Choose Network Shared Printer, and then
5 Choose your printer's queue, and then click
®
Installing the Printer Driver
appears, click Yes if you agree to the License
Agreement.
click Next.
OK.
Windows
®
Network
Windows
Note
Contact your administrator if you do not know the
location or the name of the printer in the network.
6 Click Finish.
Note
• If you want to register your product on-line, check
On-Line Registration.
• If you do not want to set your printer as Default
printer, uncheck Set as Default Printer.
Setup is now complete.
20
Installing the Printer Driver
Macintosh
®
4
For USB interface cable users
Connecting the printer to your Macintosh® and
installing the driver
1 Connect the USB interface cable to your
Macintosh
®
, and then connect it to the printer.
Improper Setup
DO NOT connect the printer to a USB port on a
keyboard or a non-powered USB hub.
2 Make sure the printer power switch is on.
5 The Brother software will search for the Brother
printer. During this time the following screen
will appear.
Note
If more than one printer is available, the following
list appears. Choose the printer you wish to
connect, and then click OK.
®
3 Click Install Printer Driver on the menu
screen.
4 Click USB cable users and follow the
on-screen instructions. Then, restart your
Macintosh
For Mac OS
Go to step 7.
For Mac OS
Go to step 5.
Note
Please see the User’s Guide on the CD-ROM to
install the PS driver (Brother’s BR-Script Driver).
®
.
®
X 10.2.4 to 10.2.8 users:
®
X 10.3 or greater users:
6 When this screen appears, click OK.
For Mac OS® X 10.3 or greater users:
Setup is now complete.
7 When this screen appears, click Add.
USB
Macintosh
21
STEP 2
Installing the Printer Driver
Macintosh
®
8 Choose USB.
9 Choose your printer, and then click Add.
5
For network interface cable users
10 Click Print Center, then Quit Print Center.
For Mac OS® X 10.2.4 to 10.2.8 users:
Setup is now complete.
Connecting the printer to your Macintosh® and
installing the driver
1 Connect the network interface cable to the
®
printer, and then connect it to a free port on
your hub.
4 Click Network cable users and follow the
on-screen instructions. Then, restart your
Macintosh
For Mac OS
Go to step 7.
For Mac OS
®
.
®
X 10.2.4 to 10.2.8 users:
®
X 10.3 or greater users:
Go to step 5.
Network
Macintosh
Note
Please see the Network User’s Guide on the
CD-ROM to install the PS driver (Brother’s
BR-Script Driver).
5 The Brother software will search for the Brother
2 Turn on the printer power switch.
printer. During this time the following screen
will appear.
3 Click Install Printer Driver on the menu
screen.
22
Installing the Printer Driver
Note
If more than one printer is available, the following
list appears. Choose the printer you wish to
connect, and then click OK.
• If there is more than one of the same printer
model connected on your network, the
Ethernet address (MAC address) will be
displayed after the model name.
6 When this screen appears, click OK.
Macintosh
9 Choose your printer, and then click Add.
Note
If there is more than one of the same printer model
connected on your network, the Ethernet address
(MAC address) will be displayed after the model
name.
10 Click Print Center, then Quit Print Center.
®
For Mac OS® X 10.3 or greater users:
Setup is now complete.
7 When this screen appears, click Add.
8 Make the following selection.
For Mac OS® X 10.2.4 to 10.2.8 users:
Setup is now complete.
®
Network
Macintosh
23
Other Information
1
1
Shipment of the printer
Caution
• Once your printer has been set up and used, we do not recommend that it be moved or shipped unless
absolutely necessary.
• Color laser printers are complex printing devices. Moving the printer or shipping it without properly removing
the installed supplies can result in SEVERE damage to the printer. As a result, your printer may not operate
properly afterwards.
• If the printer must be shipped, see the supplied Repacking Information insertion or visit
http://solutions.brother.com
transport.
• Failure to properly prepare the printer for shipping according to the instructions located at
http://solutions.brother.com
• If for any reason you must ship your printer, carefully package the printer to avoid any damage during transit.
We recommend that you save and use the original packaging. The printer should also be adequately insured
with the carrier.
for detailed, step-by-step instructions on how to properly prepare your printer for
may VOID YOUR WARRANTY.
Trademarks
The Brother logo is a registered trademark of Brother Industries, Ltd.
Apple, the Apple Logo, Macintosh and TrueType are registered trademarks of Apple Inc. in the United States and
other countries.
Microsoft, MS-DOS and Windows are registered trademarks of Microsoft Corporation in the U.S. and other
countries.
Windows Vista is either a registered trademark or trademark of Microsoft Corporation in the United States and/or
other countries.
Java and all Java-based trademarks and logos are trademarks or registered trademarks of Sun Microsystems, Inc.
in the United States and other countries.
All other terms and brand and product names mentioned in this Quick Setup Guide are registered trademarks of
their respective companies.
Compilation and Publication
This manual has been compiled and published, under the supervision of Brother Industries Ltd., covering the latest
product descriptions and specifications.
The contents of this manual and the specifications of this product are subject to change without notice.
Brother reserves the right to make changes without notice in the specifications and materials contained herein and
shall not be responsible for any damages (including consequential) caused by reliance on the materials presented,
including but not limited to typographical and other errors relating to the publication.
This product is designed for use in a professional environment.
Copyright and License
© 2007 Brother Industries, Ltd. © 1998-2007 TROY Group, Inc. © 1983-2007 PACIFIC SOFTWORKS INC.
This product includes the "KASAGO TCP/IP" software developed by Elmic Systems, Inc. © 2007 Devicescape
Software, Inc. This product includes RSA BSAFE Cryptographic software from RSA Security Inc. ALL RIGHTS
RESERVED.
24
Loading...